Search Documents

STANDING COMMITTEES Executive-A. R. LEDOUX, chairman. Membership-GEORGE C. STONE, chairman. Finance-J. V. N. DORR, chairman. Library-E. GYBBON SPILSBURY, chairman. Papers and Publications--BRADLEY STOUGHTON, chairman. Nominations-POPE YEATMAN, chairman.

Jan 9, 1919

By M. G. Cheney

THE production record of the Sinclair-Moren pool, in southeast Young County, Texas, demonstrates that under efficient operating methods a single well may obtain normal oil recovery from an area of 100 acres or more. This record is the more surprising in view of relatively adverse reservoir conditions such as lack of water drive, moderate initial reservoir pressures and a consolidated sandstone reservoir with original permeability greatly reduced by processes of lithification. This case history is considered worthy of special study in view of the ever present problem of proper spacing of wells. Cupidity, abetted by the unrestrained law of capture, has in too many instances guided development and production methods without regard for sound economic and engineering principles. Largely as a result of ill advised spacing of wells, many oil fields have brought financial losses instead of deserved profit to those using capital, time and energy in this important business of adequately meeting the petroleum requirements of what is known as our modern civilization. In March 1923, the Sinclair Oil and Gas Co. obtained initial daily production of about 12,000,000 cu. ft. of gas and 1100 bbl. of oil in its first well near the center of a 372-acre lease on the L. P. Moren land, James Rose survey, Abstract 245. This exploratory test was drilled as a geological prospect of average promise, on a plunging anticline with possibly 10 ft. of closure as mapped on the outcropping limestone of upper Canyon (Pennsylvanian) age. In subsurface, the top of the producing res-ervoir is 16 ft. lower in this well than in the highest wells but probably 25 ft. above lowest closing contour. Wells No. 2 and 3 were drilled about 1/4 mile west and southwest near a normal fault with some 30 ft. of downthrow to the southwest. The producing sand was reached at a depth of 2512 ft. and drilled to 2529 ft. in the first well. This sandstone reservoir is of Millsap Lake (middle Strawn, upper Cherokee) age. It was absent in the second and third wells, which were abandoned at the depths of 3725 or more. In April 1925, a fourth well was drilled 600 ft. east and 24 ft. lower for top of sand than No. I. Production of about 100 bbl. daily was reported from 2521 to 2562 after an 80-quart shot. This well was drilled to 4560 ft., plugged back to 2575 and shot again; but was abandoned soon thereafter because of small production.

Jan 1, 1940

The following additional notes about prices of coal in the early days were collected from the sources shown. Several data about canal tolls and labor conditions are also included. 1796, November: "The inhabitants lay it (coal) in at about 3;d. (83¢) sterling per bushel." (Ref. 73: p. 147.) 1804, March: "In March, 1804, I sent a person accustomed to mining to open the vein of coal, and to load the ark, which was accomplished, and early in the month of April the ark, with the first cargo of bituminous coal passed safely the Conewago falls, and landed her coal at Columbia, Lancaster County. The coal was sold at 31¢ per bushel at Columbia." ($7.75 per ton). This was the first coal from Clearfield County near the town of that name. (Letter from William Boyd: Pa. Senate Jour., 1833-1834, vol. 2, p. 561.) 1807: The following notice appeared in the Bedford Gazette: "Huntingdon, June 4. "Stone Coal.-Such of the farmers as wish to make experiment with stone coal as a substitute for plaster, in manuring their Indian corn, may be supplied with coal gratis upon application to Peter Hughes, at Mr. Riddle's mines, on the Raystown Branch. The proprietor of the mines offers not only to refund the carriage, but to pay the expenses of applying the coal, if upon a fair experiment it is found to be inferior to plaster, which now sells at two dollars per bushel." (Ref. 735: p. 708.) 1809: Coal was delivered in Pittsburgh at 5¢ per bushel or $1.25 per net ton. (Ref. 444: p. 50.) Coal was delivered in Connellsville at 4¢ per bushel or $1.00 per net ton. (Ibid.: p. 185.) 1810: Pittsburgh.-"Coal may be obtained of a good quality, ready delivered at 5¢ a bushel." ($1.25 per net ton.) (Ref. 315: vol. 2.) 1811: "It (coal) costs 6¢ a bushel at your door." ($1.50 per net ton.) (In Pittsburgh.) (Ref. 277: 1811, p. 68.) 1814: At Columbia, now part of Donors, Washington County, Pa., an original sale of lots in 1814 gave the purchaser of each lot the right to mine stone coal gratis from a bank on the property. (Ref. 410: vol. 1, p. 547.) "A laborer is able to dig upwards of 100 bushels per day." (4 tons.) (Ref. 277: 1814, p. 109.) A paper about the early newspapers in West Virginia says: "Collier Wanting. From 10 to 20 steady and industrious men, who understand digging coal, may obtain high wages in Kenhawa for that business, if immediate application is

Jan 1, 1942

PRESIDENT AND DIRECTOR CHESTER A. FULTON NEW YORK, N. Y. PAST PRESIDENTS AND DIRECTORS EUCENE MCAULIFFE OMAHA, NEBR. C. H. MATHEWSON NEW HAVEN, CONN. TREASURER AND DIRECTOR ANDREW FLETCHER NEW, YORK, N. Y.

Jan 1, 1944

By W. B. Humes

The use of high vacuum on a large industrial scale in the ferrosilicon process for the production of magnesium marks the coming of age of an important new metallurgical technique. The economical production of reactive metals, such as magnesium, which combine with all the well-known furnace atmospheres, has until recently been successfully carried out only by electrolytic methods. It is now apparent that, through the use of high vacuum, the distillation or sublimation of many metals can be done industrially at much lower temperatures, and hence in much simpler equipment, than heretofore has been thought possible. At the beginning of the present emergency, when the ferrosilicon process of producing magnesium was brought to the fore, little was generally known about vacuum engineering, practices, and techniques. In a comparatively short time, the available equipment has been adapted, new equipment designed and built, and a fund of know-how evolved to make possible the production of thousands of pounds of magnesium per day at pressures less than 1/ r0,000 of an atmosphere. Pilot-plant operations have been consistently maintained at pressures even as low 2s one micron (0.001 mm.). These low pressures, which previously were regarded as prohibitively costly or impossible to attain, have been demonstrated as economically feasible on an industrial scale. Necessity for Vacuum The main function of vacuum in the ferrosilicon process, and hence in most vacuum smelting processes, is to lower the temperature at which the metal may be distilled or sublimed from the reduction mixture. A secondary function is to protect the distilled metal from attack by the furnace atmosphere and to permit the formation of a dense condensate. In the ferrosilicon process, magnesium is formed by the reaction between dolomite and ferrosilicon: 2(Mg0-Ca0) -\- HFeSU / t=> aMg + MFe + (CaO)2-SiO2 The metal is distilled from the pelleted charge at a free air pressure of about 0.100 mm. of mercury (100 microns). This low pressure is not needed for the reaction, but rather serves to protect the metal vapor from the oxygen or nitrogen of the atmosphere and permits the formation of a condensate free of pyrophoric material. The reaction proceeds at air pressures as high as several millimeters of mercury, and evidence has been offered to show that the actual equilibrium pressure of magnesium at operating temperatures of 2I50°F. is somewhat higher. Experimentation indicates that the yield begins to decrease at pressures above 500 microns. While no real operating data are yet available on the relationship between

Jan 1, 1944

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By R. L. Huntington, Frank P. Vance, George F. Russell, Robert Thompson

With the advent of higher pressures in the operation of natural-gas transmission lines, the removal of water vapor from the gas has become increasingly important in order to prevent condensation or formation of gas hydrate from slowing down or stopping the flow of gas. Intelligent design of these dehydration or gas-drying plants has been hampered through the Iack of experimental data on the water vapor content of natural gas at elevated pressures. In view of this need, this present investigation was sponsored by the Southern Natural Gas Co. in the Chemical Engineering laboratories at the University of Oklahoma Research Institute. Experimental results were obtained on the water-vapor content of natural gas up to 2000 lb. per sq. in. at atmospheric temperatures. The water content at 2000 lb. is approximately two thirds as much as it is at 1000 Ib. Deviations from the ideal gas laws vary directly with pressure and indirectly with temperature. Introduction The removal of water vapor from natural gas is an important operation in connection with the production and transportation of this commodity because: I. Liquid water accelerates internal corrosion of a pipe line. 2. Accumulation of water at low points in a pipe line reduces markedly its capacity. 3. Gas hydrates, icy snowlike growths, form readily under high pressure in the presence of the lower hydrocarbons and water, often plugging up the pipe line. In order to design dehydration plants for stripping the gas of its water content, it is essential that the engineer. have a knowledge of the saturated or equilibrium water-vapor content of the gas to be processed. With the gradual increase of operating pressures around gas-producing wells and pipe lines, it was observed that the quantity of water recovered from dehydration plants or condensed in colder lines was considerably greater than had been expected from calculated contents, based on vapor-pressure data taken from steam tables. This observation prompted a number of investigators, for instance, Laulhere,3 Dea-ton,l and Hammerschmidt2 to carry out experimental work at pressures up to 600 lb. per sq. in. in order to determine quantitatively the water content of various gases. Sage, Lacey, et al.4,5 have recognized more recently the need for such data at higher pressures, but their work was done at temperatures of 100ºF, and higher. Since hydrate formation usually, if not entirely, occurs at temperatures below 100ºF., the present investigation was confined to the . lower temperature range at pressures from 600 to 2000 lb. per sq. in. gauge.

Jan 1, 1945

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By Samuel S. Wyer

The installation of the gas-producer power-plant in America has been so unusual that all engineers have viewed it with interest; a large majority, however, regard it with a lack of confidence and many with positive distrust. Despite the fact that

Jan 1, 1906

By AIME AIME

AWRDED jointly by the four AW Founder Engineering Societies the John Fritz Medal is generally regarded as the most signal honor that American engineers can confer on a fellow engineer. The roll of 34 recipients contains the names of Lord Kelvin, George Westinghouse, Alexander Graham Bell, Thomas. A. Edison, George W. Goethals, Guglielmo Marconi, and Michael I. Pupin; and among members of the A.I.M.E. now living, Sir Robert A. Hadfield, Herbert Hoover, and Daniel C. Jackling. On the evening of March 1 7 the name of Paul Dyer Merica was formally added to this list of illustrious engineers when the medal was presented to him at a dinner at the Metropolitan Club in New York. The citation read. For important contributions to the development of alloys for industrial uses. Arrangements for the dinner were made by the following committee representing the four Founder Societies: R. C. Allen, George S. Davison, A. A. Potter, and J. B. Whitehead.

Jan 1, 1938

By C. L. Siebenthal

C. E. SIEBENTHAL, ? Washington, D. C.-From being one of the most maligned of metals-a veritable bugaboo-cadmium has almost overnight become respectable, though its slender claim to respectability rests almost wholly on the possibility of its substitution for tin. Preliminary to any campaign for such substitution, particularly for enforced substitution, the possible supply of cadmium should he determined as closely as possible; for that reason the statistical inquiry of which this paper embodies the results was undertaken. Production Cadmium is marketed in two forms, as metallic cadmium, in sticks or bars, and as cadmium sulfide, the pigment. The metal has found its greatest field of use in this country as a component of an easily fusible alloy that is used in automatic fire extinguishers. The sulfide is .used to some extent in paints but chiefly to give color and luster to glass and porcelain. The metal was first made in this country by the Grasselli Chemical

Jan 12, 1918

By Thomas M. Drown

IN a communication to this Institute at the Baltimore meeting, February, 1879,* on the "Determination of Silicon in Pig Iron and Steel," the method recommended was the treatment of the metal with nitric acid until action had ceased, and then evaporating with sulphuric acid until the nitric acid was nearly or quite driven off After filtration of the siliceous and carbonaceous residue, and washing with hot water and hydrochloric acid, a silica was obtained, on ignition, which was quite pure. Since this paper was read before the Institute, we have had large experience with the method, and * Transactions, vol. vii, p. 346.

Jan 1, 1880

By Courtenay de Kalb

The following observations upon onyx-marbles are fragmentary, and may shortly be rendered superfluous by the appearance of a work upon these interesting stones by Prof. George

Jan 1, 1896

By C. H. Benedict, H. C. Kenny

A 2000-ton ammonia leaching plant has been operated by the Calumet & Hecla Mining Co., at Lake Linden, Mich., continuousl~ since February, 1917, except from April, 1921, to April, 1922, during the period of depression following the European war. A description of this plant has been published elsewhere.1 The present article describes the operation of the plant since 1917, together with the changes in the process that have been found to be advisable. In spite of the fact that this plant and that of the Kennecott Copper Co. are the only ones operating on a large scale, much experimental work is being done on ammonia leaching, as applied to oxidized ores, and it is to aid these and other investigators that this detailed account is given. For the benefit of those unfamiliar with the original article, the following short abstract is given, as an introduction to a more detailed account of the process and the reasons for present practice. Rêsumê of Previous Article Leaching on a commercial scale began in July, 1916, and by Februsry, 1917, the plant of 2000 tons capacity was in commission. The ore treated is a conglomerate containing native copper and no sulfides or oxidized copper minerals. Before leaching, the ore is crushed by steam stamps and Hardinge pebble mills to pass a 28-mesh screen. Free copper is removed, by gravity concentration, on Woodbury jigs and Wilfley tables, and colloidal slime for oil flotation is removed by quadruplex Dorr classifiers. The leaching sand remaining contains about 2 per cent. + 28-mesh material and 15 per cent. — 200-mesh and carries from 8 to 14 lb. of copper per ton, depending on the grade of ore worked. The solvent employed in leaching is a water solution of ammonium carbonate,

Jan 1, 1924

By K. J. Reid, H. A. Lex, I. Iwasaki, K. A. Smith

The effects of autogenous grinding and conventional grinding on the floatabilities of copper-nickel sulfides from Duluth gabbro were investigated. At the same mesh-of-grind copper, nickel, and cobalt recoveries were higher and residual sulfur in the flotation tailings was lower with the autogenously ground pulps. With the ball-mill ground pulps the residual sulfur in the tailings could not be lowered to the level attained by the autogenously ground pulps even at increased levels of the collector addition. From mineralogical examinations of concentrate and tailings samples, an electrochemical interaction between grinding media and sulfide minerals was thought to have a greater effect on sulfide mineral flotation behavior than the breakage characteristics of the ore samples in these two types of mills.

Jan 1, 1984

By E. J. Ripling, S. I. Liu

IT has been shown in a number of recent publications that much information on the mechanical behavior of metals can be gleaned by first deforming test specimens under one set of conditions, and then evaluating the effect of this deformation by means of a subsequent tensile test. A straining procedure of this type has been applied to study the flow behaviors of a number of metals.1, 2 In these studies the prestraining and testing were both tensile strains, while the straining temperature was varied between the prestraining and testing steps. These data indicate that there is a more or less general flow behavior exhibited by all metals which are pre-stretched at one temperature and then tested in tension at a second temperature. Prestraining a metal at a high temperature produces a lower yield strength during the subsequent low temperature strain than would the same total strain at the lower temperature. On reversing the order of the strains, low temperature prestraining produces a higher yield strength during the subsequent high temperature straining than would a single high temperature strain of the same magnitude. Unlike the flow behaviors, the fracturing characteristics of metals when prestrained under one set of conditions and tested under a second set of conditions is quite material dependent. The fracture behavior of a number of steels2" as well as of a commercially pure zinc,4 have been investigated by these two-step tests and was found to depend upon the position of the transition temperature with respect to the prestraining and testing conditions. Since these fracturing phenomena are complicated by the appearance of the transition temperature, it has been difficult to reliably define the basic effect of a two-step straining procedure in fracturing. Metals crystallizing in the face-centered cubic system do not exhibit transition temperature effects so that the mechanical characteristics obtained on these materials could serve as a base for two-step straining behaviors. Consequently groups of specimens of the aluminum alloy 24s-T4 were prestrained various amounts at room temperature in either tension or compression after which these strained specimens were further strained to failure, or tested in tension, at either room or some lower temperature. Other groups of 24S-T4 specimens were prestretched at various low temperatures after which these were tested in tension at room temperature. These straining techniques then made it possible to compare the behaviors of aluminum with the behaviors previously presented for steels. Material and Procedure The commercial aluminum alloy 24S-T4 in the form of 3/4 in. rods was used in this investigation. The material was subjected to the following treatments before machining: 1—resolution treating at 920" & 10°F for 45 min, 2—quenching in water at room temperature, and 3—aging at room temperature for four days. The re-heat treated material was then machined to either of the specimen shapes shown in Fig. 1. Fig. la shows the threaded-end specimen used for prestraining in compression. Fig. 1b shows the specimen used for both prestrain in tension and final testing. The material subjected to precompression in the form of the specimen shown in Fig. la was re-machined to the specimen shape in Fig. 1b for final testing. Prestraining in tension and final testing were done without any intermediate machining. All straining was performed on a 10,000 1b Riehle tensile testing machine. Tensile strains were conducted in a specially designed concentric fixture which produced an eccentricity of less than 0.001 in." The change in diameter at the minimum section of

Jan 1, 1954

By H. C. Brassfield, R. E. Fryxell, E. C. Duderstadt, E. A. Aitken, P. K. Conn

Permeation rates of hydrogen through are-cast tungsten were measured at temperatures from 1300" to 2600°C with hydrogen pressure differentials of 1 and 0.1 atm across isothermal membranes. Rates were nearly Proportional to square root of pressure, were inversely ProPortional to membrane thickness, and were temperature-dependent according to the equation: p = permeation coefficient in cu cm (stp)-mm per sq cm-min-atmlr2, R = gas constant in cal per mole-OK, T = absolute temperature in OK. Permeation rates of oxygen through tungsten were deternlined in the range 1965" to 2300°C and at calculated oxygen (02) pressures of 3.3 x 10-4 to 2.2 x at?n using sealed capsules containing Kmown quantities of tungsten oxide. Permeation coefficients obtained in this manner had a temperature dependency in the range of 40 to 45 kcal per mole of permeating species. Permeation coefficients for oxygen were higher than those for hydrogen in the temperature range studied. This is probably the result of oxygen solubility being much greater than hydrogen solubility at these temperatures at a gzven pressure. The purpose of this investigation was to determine experimentally the permeabilities of hydrogen and oxygen through polycrystalline tungsten at temperatures ranging from 1300° to 2600°C. Permeation rates of hydrogen through tungsten have been measured at temperatures up to 925°C,but no previous measurements have been reported for the temperature range covered in this investigation. Some diffusion measurements3&apos;&apos; and solubility measurements3 have been made for hydrogen at temperatures below 2200°C. No previous permeability studies of oxygen through tungsten are known to the authors; however, efforts have been made to determine diffusion rates5-&apos; and solubilities PERMEATION THEQRY Permeation has been defined by ortton" as the overall steady-state flow process from the gas phase on one side of a membrane or wall to the gas phase on the other side and includes the steps of adsorption, solution, diffusion, exsolution, and desorption; in a given temperature range, any of these processes may be rate-controlling. For diatomic gases, which dissociate prior to diffusion, the quantity of gas which permeates through a membrane or wall at a given temperature is directly proportional to the surface area of the membrane, the length of time of permeation, and the difference between the square roots of the pressures on each side of the membrane, and it is inversely proportional to the thickness of the membrane when diffusion-controlled, thus: q = total amount of gas permeating a membrane, p = temperature-de pendent permeation coefficient, A = area of membrane exposed, / = time, p i = gas pressure of high-pressure side, p2 = gas pressure of low-pressure side, d = thickness of membrane. When the surface reactions are not rate-controlling steps and the solution of the gas in the metal follows Henry&apos;s law, the permeation coefficient, P, is equal to the product of diffusivity and solubility. The permeation coefficient is also temperature-dependent according to the equation: Po = permeation constant, Q = activation energy, R = gas constant, T = absolute temperature. MATERIALS The tungsten materials used in this investigation were greater than 99.9 pct pure. The interstitial impurities ranged from < 1 to 50 pprn C, 7 to 35 ppm O, less than 15 pprn N, and undetectable quantities of hydrogen. Previous high-temperature studies of are-cast tungsten have shown that thermal treatment similar to that which the hydrogen permeation cells experienced reduces the carbon content from starting levels of 50 to 60 ppm to about 30 ppm. Metallic impurities were in the low (1 to 50) ppm range. The argon gas used in this investigation contained about 8 ppm N. None of the following gases were

Jan 1, 1968

By H. A. Wriedt

Zinc-vapor pressures in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C were measured by an isopiestic method. Thermody-na?nic properties of zinc in these solutions were derived directly and those of iron with a Gibbs-Duhem integration. Zirzc and iron exhibit large, positive, and moderately temperature-sensitive deviations from ideality. Excess enthalpies and Gibbs energies are positive in the ranges studied. It has been establzshed in relating published phase equilibria to the Gibbs energies of forming solid solutions that positive departures from ideality also exist in the fcc solutions. Tlze stability, as defined by Darken, of the bcc solutions is small but positive at 703.5"C. Its decrease with decreasing temperature indicates that a miscibility gap may exist in the stable or metastable bcc solutions at lower temperatures. The changes of thertnodynanlic properties relatable to changes in magnetic state are minor compared to other changes due to alloying. The accuracy with which the relation between lattice parameter and composition of the bcc solutions is known has been improved. Zinc increases the lattice parameter of a iron by O.ZOZA per unit atom action zinc to at least NZn = 0.25. TO our knowledge, only Ciganl has previously investigated thermodynamic properties of the bcc solutions of the Fe-Zn system. He measured zinc-vapor pressures in the temperature range from about 320" to 360°C by an effusion technique. We have measured the vapor pressures of zinc in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C by an isopiestic technique. This investigation and the pursuant thermodynamic computations are part of a program for studying several properties of these solid solutions. In the appendix we report a remeasurement of the relation at room temperature between the lattice parameter and zinc content. Related work not reported herein embraces measuring the diffusivity2 of zinc in ferrite at 700" to 900°C and the Curie point temperature3 as functions of composition. EXPERIMENTAL METHOD AND APPARATUS Purified iron at a series of constant temperatures was saturated with zinc at a series of constant zinc-vapor pressures, the range of conditions being so limited that the equilibrated solid solutions were ferri-tic. The equilibration was conducted in long capsules, Fig. 1, that had been evacuated, gettered with titanium, and sealed. The purified iron, part of a vacuum-melted ingot of electrolytic-iron stock (Glidden Co. 1044-grade), had the impurity contents listed in Table I. It was used in the form of millings about 0.001 in. thick. A zinc of 99.999 pct purity (United Mineral and Chemical Corp.) and later one of 99.9999 pct purity (Cominco Products, Inc.) were used, with no observed difference in results. Sufficient zinc was placed in the capsule (separate from the iron and kept at a different temperature) to supply the vapor phase and the iron alloy, while leaving a pool of pure liquid zinc throughout the run. The imposed temperature of the residual zinc pool fixed the vapor pressure of zinc throughout the capsule; condensation was avoided at other locations by making this the lowest temperature in the capsule. Two common complications of nonisothermal systems were, we believe, effectively absent from ours: first, molecular species other than monatomic have no appreciable concentration in zinc vapor at 700" to 900~~: second, the development of zinc-pressure differentials in the capsules was suppressed by use of relatively large-diameter tubing and the absence of diluents in the zinc vapor other than desorbed impurities. The specimens and zinc pool were located at two isothermal zones (each ranging within 1°C over several inches) of a wire-wound, 37-in.-long vertical-tube furnace. The required temperature distribution was achieved by external adjustment of the currents in three electrically isolated windings. The temperatures of the isothermal zones were controlled independently by ther-

Jan 1, 1968