Search Documents

By Walter Crafts, C. M. Offenhauer

IN a previous study' of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is a more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about r1to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, 1 per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to 1-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudomartensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously' that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By C. S. Smith

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Dr. Gerhard Derge; Editorial Assistant, M. A. Redmyrski; Staff Coordinator, James J. Burke. THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Post-President; John Chipman, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretory. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman- Dennis Carney John Chipman J. C. Fulton J. H. Hollomon H. H. Kellogg, A. E. Lee, R. Moddin, J. D. sullivan, and D.' Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. lnstitute of Metals DM lion: Robert Maddin, Chairman. F. Lincoln Vogel, Jr.. Vice chairman. W. A. Backofen R. W. Boliuffi J. H. Bechtold' M. B. Bever R: S. Busk C 6. Goetzel poul Gordon C. D. Grobom, Jr., Robert F. Hehe-mann R. I. Joffee F. i. Joumot Jr. lrvin R. Kromer, A. J. Leno. Horold Morgolfn, C. J. McHargue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alon U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman. T. B. King, F. C. Laogenberg, W. O. Philbrook, and T. 0. Winkler. Publishod bimonthl by the American Institute of Mining Metollurgicol and Petroleum Engineers Inc., 29 West 39th Street, New York 16, N. Y. Telephone: PEonylvanie 6-9220. Subscription $20 par yew for non-AIME members in United States and North, South and Control Americo $25 foreign; $5 for AIME members. Single copies, $4.00, single copios foreign $5,00. The AIME is 1958 by the Amarican mode or opinion axpressed in it* publications ... Copyright by the Amarican lnstitute of Mining, MataIlurgicol, and Petrolum Engineers, Inc,. . . Reg. istered cable address AIME New Yark ... Indexed in Engineering Inderx, Industrial Arts ...Index and Chemicol Number5. Absrtracis . . . Second class postage paid at New York,Indor. N. Y., Industrialond Ann Arbor, Mich.

Jan 1, 1959

By Goro Shimaoka, Kichizo Niwa

IN the past, the crystalline states of graphite in cast iron have been studied by many investigators. Recently several authors 1-4 have published interesting information on the crystal texture of the individual graphite grain, especially spherulites in nodular cast iron. In regard to the crystal structure of graphite, Lipson and Stokes0 howed by powder X-ray analysis that most of the crystals contain about 14 pct rhombohedra1 structure (ß-form) which differs from the hexagonal structure (a-form) in the sequence of layer stacking. Hoerni6 onfirmed the existence of the ß-form in a single crystal with electron diffraction by Kossel-Moellenstedt's method. Furthermore, Hoerni and Weigle7 found extra reflections in electron diffraction patterns, which are given by a unit cell twice as large as the usual one in the basal plane. Recently, Lukeshs observed graphite twinning and satellite reflections in his X-ray work and considered them as evidence for the existence of an orthorhombic superstructure. Owen and Street" and Matuyama" studied the structures of graphite crystals in several types of cast iron, using the X-ray powder method, and they showed that the graphite crystal contains a certain amount of the ß-form, an amount which varies with the sources of the cast iron used. The present study was made in order to secure structural information on graphitization in cast iron. Electron diffraction studies on the structure of single graphite flakes segregated from molten carbon or silicon-rich iron at 1200" to 1500°C are reported. Experimental Honkeiko pig iron (4.05 pct C, 1.59 pct Si, and 0.65 pct Mn) was used as the solvent of carbon or silicon. The pig iron was melted in an open furnace and a small quantity of metallic silicon was added to the melt at 1300°C. The melt was heated to 150O°C, and then retort black carbon or metallic silicon was added little by little. The components added to the bath contained approximately 5.0 pct C and 2.0 pct Si in the carbon-rich material, and 3.8 pct C and 5.4 pct Si in the silicon-rich iron. These two types were held at 1500°C and then cooled without graphitizing by cutting the heat sup-

Jan 1, 1958

By Lyall Zickrick

NUMEROUS brands of virgin pig lead are used in the manufacture of lead and lead-alloy cable sheath for commercial cables. In changing from one brand of pig lead to another a readjustment of press operating conditions is nearly always necessary. This is due largely to different flow characteristics, and some brands extrude at a much lower pressure than others; for example, copper-bearing lead requires much more pressure than a low-bismuth lead under the same operating conditions. With the modern type of lead press the extrusion practice in general differs very little. Molten lead at a temperature of 375° to 400° C. (710° to 750° F.) is cast in a water-cooled cylinder and allowed to cool or solidify into a slug for six to nine minutes. . This slug is forced into the die block and around the core tube through which the cable runs. The die block is held at an optimum temperature by means of gas flames, usually 175° to 225° C. (350° to 4.35° F.). Measurements of the tem¬perature of the cable sheath taken at the time of extrusion have covered a range of 190° to 225° C. (375° to 435° F.). According to Tammann, the rate of extrusion for a metal under constant pressure through a simple orifice is almost doubled for each 10° C. rise in temperature. Because of the irregularity of die-block construction, such a great increase is not obtained in lead-cable extrusion practice. To obtain more" definite information about the effect of small per¬centages of metals usually present as impurities in virgin pig lead, a series of compression tests were made covering several different brands of lead and various alloys. Since the usual temperature of the sheath is approxi¬mately 200.° C. as it emerges from the die block, these compression tests were all performed at 200° C. Five different brands of virgin pig lead were selected, as follows: Brand A: A desilverized western lead of very high purity. This lead contains neither copper nor bismuth. Brand B: A bismuth-free southeastern Missouri lead, usually con¬taining 0.05 to 0.08 per cent copper. Brand C: A copper-free mid-western desilverized lead of very good grade, usually containing around 0.06 to 0.10 per cent bismuth.

Jan 1, 1932

By A. E. Outerbridge

It has been generally accepted as a fact that cast-iron, under the influence of repeated shocks, becomes brittle, and will finally break under a blow which otherwise it would have withstood. It will probably surprise metallurgists, therefore, to learn that experiment disproves the supposed fact, and establishes exactly its opposite. The result of about a thousand tests of bars of cast-iron of all grades, from the softest foundry-mixtures to the strongest car-wheel metal, enables me to assert with confidence that, within limits, cast-iron is materially strengthened by subjection to repeated shocks or blows. It is very well known that the usual process of annealing castings—such, for example, as car-wheels—increases their strength by relieving cooling-strains. But it is not well known (if known at all prior to this announcement) that the molecules of cast-iron are capable of movement—for they do not touch each other*—without the necessity of heating the casting, and that they can thus rearrange themselves in comfortable relation to their neighbors, and relieve the overcrowding near the surface of the casting. In more technical words, a molecular annealing may be accomplished at ordinary temperatures which will release the strains in the castings, precisely as does annealing by slow cooling in heated pits or ovens. A statement so surprising should not be made without sufficient data to establish its correctness beyond cavil, since it is contrary to former

Jan 1, 1897

By J. W. Snavely

WITH all the advantages of handling bulk materials by means of belt conveyor also go some problems, one of the most persistent being that of cleaning. When sticky materials are being carried; the build-up of material on the return idler rolls results in difficulty of belt training. Much attention has been given to the problem of cleaning conveyor belts, and a great variety of cleaning devices have been developed. Even the best involve troublesome maintenance, and none can completely remove the fine particles imbedded in the belt cover, which cause rapid wear of the return idler rolls, and at the same time, of the belt cover as well.

Jan 12, 1951

By D. A. Sullivan, D. W. Fuerstenau

The authors investigated the comminution of quartz and limestone mixtures in a ball mill, showing that the distribution modulus of a comminuted material is the same whether it is ground separately or as part of a mixture. Analysis of the ground products indicates that quartz and limestone consume energy during ball milling in proportion to their mass fraction in the mixtures. Recently Schuhmann' made a significant contribution to comminution theory by proposing that complex comminution operations comprise the summation of many individual comminution events. By means of the single comminution event hypothesis, Schuhmann derived the Charles energy-size reduction relationship by considering that fragments of every particle crushed during a single impact have a size distribution characterized by the Schuhmann size distribution. In this paper, the size reduction of mixtures of solids in ball mills is analyzed by considering that size reduction occurs as many single comminution events. If a mixture of two materials is being ground in a ball mill, each successful impact of a ball with a particle of one material should yield an assembly of particles whose size distribution is characteristic of that material. Considering both materials to follow the Schuhmann size distribution equation, the size distribution of material 1 in the product is Where y is the weight percentage of material 1, which

Jan 1, 1962

Established as a Division November 17, 1948 B W Gonser, Chairman J C Kinnear, Jr, Past Chairman H H Kellogg, Chairman-Elect R C Cole, Vice-Chairman, '58 A E Lee, Jr, Vice-Chairman, '59 W R Opie, Vice-Chairman, '60 R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y

Jan 1, 1957

By E. W. Engle

Fox several years the Fansteel Products Co. has been engaged in the production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770° C., tungsten 3350° C., and molybdenum 2550° C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum some¬what resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids.

Jan 3, 1925

By E. R. Parker, E. A. Smith

Metallurgists and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applica-tions and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. Experimental Procedure Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were

Jan 1, 1944

By E. A. Smith, E. R. Parker

Metallurgists and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applica-tions and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. Experimental Procedure Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were

Jan 1, 1944

By Sidney Diamond, Charles Wert

The anelastic behavior of Ni-C alloys of nominal 0.5 wt pct C has been determined over a wide temperature range. The most prominent damping effect, that due to the presence of C-C pairs, was measured both above and below the Curie temperature. The effect on diffusion of the C-C pairs by magnetic spin ordering is deduced to be very small. The diffusion coefficient for C-C pairs in nickel is given by the expression ThE solid-state diffusion of both interstitial and sub-stitutional solutes in ferromagnetic solvents has been the subject of a number of investigations. Measurements of the self-diffusion of iron,"' the diffusion of nickel1,4 gold,"1 and cobalt4 into iron, the diffusion of vanadium in an Fe-V alloy,' and the diffusion of cobalt and nickel in Co-Ni alloys9 show an unusual behavior. In both the ferromagnetic and paramagnetic regions, far removed from the Curie temperature, the diffusion coefficient, D, obeys an Arrhenius relation. However, in the ferromagnetic region D is markedly lower than would be expected from an extrapolation of D from the paramagnetic region; this results in an increase in the activation energy in the ferromagnetic region. The cause of this effect for self- and substitutional diffusion is uncertain. Since substitutional diffusion is presumed to proceed by the vacancy mechanism, it has been variously suggested that the increase in activation energy below the Curie temperature is due to one of the following causes: 1) an increase in the energy of formation of a vacancy because of local demagnetization around the vacancy,2,3 2) a decrease in vacancy mobility in the ferromagnetic state,' or 3) an effect on the entropy of motion of a vacancy in the ferromagnetic state.5 Quite another explanation for the observed effect has been proposed by Borg.7 The diffusion coefficient is a function of the elastic constants of a metal. Since the temperature dependence of the elastic constants often changes at the Curie temperature, the temperature dependence of D might be expected to undergo a universal change in the vicinity of the Curie temperature. The magnitude of the change in D would, of course, depend on the magnitude of the change in the elastic constants. One might attempt to differentiate between vacancy effects and elastic effects by making measurements on interstitial alloys, in which vacancy effects play no role. Some measurements of this type have been made; this paper reports additional observations. Measurements of the diffusion of carbon in a Fe by a tracer technique8 and of the diffusion of carbon in a Co and in Co-Fe alloys by a decarburization method9 reveal a small effect, if any, on D of the magnetic change at the Curie temperature. If the effect of spin ordering is only to alter the parameters controlling formation or mobility of a vacancy, interstitial diffusion should indeed remain unchanged through the magnetic transition, as these measurements imply.

Jan 1, 1968

By V. Patarini, D. Kuehl, F. Galasso, M. Salkind

In recent years, a great deal of research has been directed toward the production of continuous low-density, high-strength, high-modulus boron fibers for aerospace applications. A technique which has proven to be quite successful for forming these fibers involves the reaction of boron trichloride and hydrogen on a hot tungsten wire. In this process, a boron fiber is produced which consists of a tungsten boride core covered with amorphous or crystalline boron depending on the temperature of the preparation.2,3 The purpose of this paper is to present the properties which have been obtained to date from measurements and observations on these fibers. Selected samples of boron filament produced by reacting boron trichloride and hydrogen on a 0.5 by 10-3 in. diam tungsten wire substrate using different reacting temperatures were cross-sectioned, polished, and photomicrographed with cross-polarized light. The temperature of the wire was measured using a two-color optical pyrometer. Photomicrographs of these samples are shown in Fig. 1. Three general types of boron, in addition to the tungsten borides, have been identified by means of X-ray powder diffraction techniques: a) at low temperatures (below 1400°C) the boron is deposited in the amorphous form; b) at temperatures between 1400° and 1500°C the boron is deposited in the ß tetragonal form; and, c) above 1500°C the boron is deposited in the B rhom-bohedral form. In the depositing range of 1400" to 1500°C the boron initially deposits as amorphous and becomes crystalline as evidenced by the large equi-axed grains which then merge into columnar grains in later stages of boron deposition. This can be seen in Fig. 1 and has been observed in the X-ray patterns of these fibers, which contain both halos from the amorphous boron and lines from the ß tetragonal form. Above 1500°C the only boron reflections observed in the X-ray patterns were those of the ß rhombohedral form and only columnar grains are seen in the photomicrographs. Photomicrographs of the surface in Fig. 2 show the smooth-surface kernal-type deposition which corresponds to the amorphous form and the rougher surfaces which correspond to the crystalline form. Mechanical measurements were made on amorphous boron produced at 1300°C rather than the crystalline boron because the strengths of these filaments were greater and were more consistent. A tensile tester consisting of a fixed crosshead containing a double

Jan 1, 1967

NEW MEMBERS The following list comprises the names of those persons who became members during the period Feb. 10, 1916 to Mar. 10, 1916. ALLAN, FERGUS L., Min. Engr., Cons. Min. Engr., Mexico Mines of El Oro, El Oro, Mex. ARMSTRONG, EMERSON WARREN, Met.,. Mina Bibilonia, La Libertad, Nicaragua, C. A. BABB, P. A Blaisdell Coscotitlan Syndicate, Pachuca, Hgo., Mex. BANDY, PERCY J Fundicion Delicias, Calle Delicias, Mexico, D. F. BELLWALD, J. N Apartado 1488, Mexico, D. F. BILLICK, DON CARLOS, Min. Engr., Supt., Hess Gold Mines Co., Alturas, Modoc Co., Cal. BITLER, FRANK L., Cons. Min. Engr., Birkinbine Engineering Offices, Parkway Bldg., Broad and Cherry Sts.. Philadelphia. Pa.

Jan 4, 1916

By J. C. Bowling

Factors governing the choice of building types, materials, and the details of construction for mineral processing plants in remote locations with cold climates are discussed. Alternative types of building insulation in common use are described and a comparison is made of their suitability under various conditions.

Jan 1, 1973

By K. Hodgson, N. C. Joughin

The detailed mechanism of rockbursts and other forms of damage due to rock failure in underground mining is as yet unknown. Studies of the energy changes which necessarily occur when an excavation is made underground seem to provide the best understanding of the phenomena leading to rock failure and damage (see Cook 1). It is common knowledge that the damage and rockburst hazard increases with depth and is greatest at remnants and in regions mined in an irregular manner. The rate at which energy is released as an excavation is enlarged provides an objective parameter to describe mining geometry in terms which are significant to studies of rock failure. In this paper, it is shown empirically that the rate of energy release per unit area increase in the size of an excavation is closely related to seismicity and incidence of damage in the mine. Consequently, it is suggested that the energy release rate is an important parameter in the design of underground mine layouts. Observations were made at two mines: the East Rand Proprietary Mines, Ltd. (E.R.P.M.), at a depth of about 9000 ft, and at Harmony Gold Mining Co., Ltd., at a depth of about 5000 ft. At both of these mines continuous recording seismic networks were in operation. (See Cook and Joughin.3) DESCRIPTION At E.R.P.M. the gold-bearing reef dips at approximately 35 degrees and is presently being mined at depths from 8000 ft to 11,000 ft below surface. The rock surrounding the excavation consists of a very homogeneous quartzite extending far into the hangingwall and footwall. The stoping width is approximately 40 in.

Jan 1, 1967

By Hermann Irresberger

SUMMARY In the German hard coal industry, relevant parameters influencing strata control have been identified in many years of intensive research work. The research results allow the formulation of the technical requirements on the design of shield supports as a function of the geological and operational conditions the face machinery is subject to. Keys to strata control are support resistance adjusted to the individual conditions of application and the tip-to-face interval. The technology to implement these requirements in actual operation is available. The automation of the shield-advance work cycle, currently setting in, can further contribute to improve strata control. In doing so, however, we must not forget the demand for an unsophisticated and low-cost design of shield supports with high operational safety. INTRODUCTION The German hard coal mining Industry produces coal from flat and inclined seams in depths between 400 and 1,300 m. The coal is exclusively won by longwall working involving face lengths up to 280 m. The thickness of the seams being worked is between 0.7 m and 4.5 m. Coal winning is fully mechanized with drum shearers or coal ploughs; two, three, or four leg shields are predominantly used as supports.

Jan 1, 1984

By J. Spotts McDowell

INTRODUCTION The magnitude of the thermal expansion of silica brick, and its inability to withstand rapid temperature changes, present problems of considerable importance in the manufacture of siliceous refractories. In the study represented by the experimental data herein described, these problems are considered from the point of view afforded by the results of recent investigators: Fenner and his associates of the "Geophysical Laboratory, Washington, D. C., who have established the stability relations of the silica minerals, and Endell and co-workers in Berlin, who have studied the changes brought about in the constitution of siliceous refractory materials upon the application of heat. In the process of manufacture, the quartzite from which the brick is made changes in part into cristobalite and tridymite. The attempt is herein made to determine by microscopic methods the degree of transformation in various specimens of test bricks manufactured at slightly varying temperatures of burning, with varying coarseness of grain, and to determine the effect of repeated burning. The effect of variations

Jan 10, 1916

By Y. M. Chang, C. H. Pitt

A jet slurry apparatus has been constructed to test corrosive/erosive wear properties of grinding ball metal. Plain high carbon steel heat treated to a hardness of about 60 Rc was used. Slurries of quartz and chalcopyrite ore concentrate were used as the jetting media. Weight loss due to pure corrosion was determined by the linear polarization technique. Weight loss due to pure erosion was determined by jetting while cathodically protecting the sample. By comparing the total weight loss with the sum of the weight losses from pure corrosion and pure erosion, it was found that there was a synergistic effect between corrosion and erosive wear. Corrosion rate, erosion rate, and total erosion/corrosion rate are given as a function of pH and mineral type.

Jan 1, 1986

By Charles Eichrodt

THE ore that is being treated by the present plant lies between the leached zone, or capping, and the mixed sulfide and oxide zone. The principal copper minerals are chalcanthite (CuSO4.5H20), brochantite (CuS04 3Cu (OH)2) and atacarnite, (CuC12.3Cu (OH)2). There are, in addition, some other minerals such as cuprite and kröhnkite (CuSO4. Na2SO4.2H20). These minerals, with many others, occur in a greatly crushed granodiorite rock. Most of the copper-bearing minerals occur in the cracks and veinlets, but there are disseminated values and it is probably the relative proportion of these that accounts for some otherwise unexplainable variations in extraction. The entire mineralization of the ore is complex and varies with depth. This variation, the problems presented thereby, and the effect of various constituents of the ore will be taken up in detail. An analysis of an unweighted composite of the ore treated during 1927 follows:

Jan 1, 1930