Search Documents

By D. R. Semmes

The possible oil territory of Alabama can be readily divided into two regions, the Paleozoic area of the north, and the Coastal Plain province of Cretaceous and younger formations lying to the south. This latter area has received much attention in the last few years and has been described by a number of writers.' Although the possibilities of the Cretaceous series have been much emphasized by recent writers, the fact remains that the two, or possibly three, localities where oil or gas have been found in anything like paying quantities are confined to the area of Carboniferous rocks. Moreover, almost all of the oil seeps and a good percentage of the gas seeps are confined to this area.2 Topographically, as well as structurally, the Paleozoic area can be divided into three rather well defined provinces: (1) The broad, open Coosa Valley lying adjacent to the crystalline oldland, with comparatively little relief, except for occasional longitudinal ridges and rather intense folding; (2) the plateau region of horizontal or gently warped Pennsylvanian strata broken by occasional anticlinal valleys aligned northeast and southwest, outliers of the Coosa Valley proper, in which the older Paleozoic formations are exposed—a region of much relief (200

Jan 1, 1921

By J. J. Jakosky

THE fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.1 One of the most impor-tant measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtain-ing bottom-hole data. The applications of bottom-hole pressure or fluid-level measure-ments are based on simple hydrodynamic principles. Under equilib-rium conditions, pbh = hd + pg + pch [ l] when pbh = bottom-hole pressure, lb. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, lb. per sq. in. per foot, pg = weight of section of gas column 1 in. square from fluid level to casing head, pch = casing-head pressure, lb. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casing head plus the casing-head pressure. At moderate rates of flow, the rate of production is approximately proportional to the difference between the reservoir, or static bottom-hole, pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939

MEMBERS-QUALIFICATIONS AND ELECTION SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall he entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which be must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which be may belong.

Jan 1, 1938

By E. A. Swedenborg, J. S. Ross

Oil-field waters enter into many underground problems with which the petroleum engineer has to deal. Whether the problem is one of infiltration or natural encroachment, it is always desirable to determine the source of the water before commencing repair or remedial work. The usual mechanical tests for determining the source of extraneous water in wells are slow and expensive. An excellent means for the identification of oil-field waters may be afforded by their chemical characteristics when the chemical character of waters from the various sands has been established by careful sampling and analysis cautiously interpreted. In the Salt Creck field, Wyoming, a fairly high degree of efficiency has been attained in the control of field operations by utilizing the information afforded by the analysis. All of the operating companies appreciate this means of identifying waters, with the result that water-sampling has become general practice. Most of the chemical work dealing with Salt Creek waters has been done since the laboratories of the Midwest Refining Co. and the U. S. Geological Survey, were established in the field; the former in 1922, the latter in 1924. A spirit of cooperation has existed between the company and the government personnel by which many of the data for this paper were made available. Sands of the Salt Creek Field The principal sand horizons in the Salt Creek field are the Shannon, First, Second, and Third Wall Creeks, Dakota, Lakota, Sundance and Tensleep. Of these the important oil producers are the First Wall Creek, Second Wall Creek, Lakota and the Sundance. The Third Wall Creek is lenticular and is productive in only a few wells in the southern end of the field. There are also a number of shale wells, but they do not produce water in any appreciable amount. The stratigraphic position of these sands and their relative thicknesses are shown on the condensed composite section of Salt Creek

Jan 1, 1929

By T. B. Gyles

Zinc is made by the National Smelting Co. and its associates by both the horizontal retort process and the vertical retort process developed by the New Jersey Zinc Co. This paper deals only with the horizontal retort practice at Avonmouth. That the horizontal retort process does survive in all countries in some form or other is due to at least partial success in overcoming some of the inherent difficulties of the process. The horizontal retort furnaces ran into considerable difficulties when the product of the selective flotation of mixed lead and zinc ores became the normal material for treatment. It is necessary, therefore, to make some reference in connection with the process to the preliminary treatment of the ore prior to distillation.. Therefore we include some small reference to this aspect in our description. Furnace Design and Structure Of the types of furnaces in operation at the company's various works, those at Avonmouth are perhaps more typical of the trend to utilize large units, with a subsequent saving in costs, such as heating and supervision.

Jan 1, 1937

By C. S. Roberts

Four binary alloys in this system were creep tested at 300°' to 600°F. A photographic study of microstructural changes showed that the outstanding creep resistance results primarily from a potent precipitation hardening locally at grain boundaries. Twinning was correlated with the primary stage and nonbasal slip with the tertiary stage of creep. THE utility of the rare earth metals as ingredients of magnesium alloys destined for elevated temperature application has been recognized for about 15 years. A review of the early development of these alloys has been given by Leontis. 1,2 It has been only recently that a desire has arisen to understand basically their remarkable creep resistance. The present research had that object. The work of Leontis showed that the differences between the behavior of the individual magnesium-rare earth element binaries was of commercial significance. However, the variations were small compared to the overall difference in creep resistance between the group as a whole and the magnesium alloys of the Al-Zn type. It was decided to conduct this investigation with one binary system which would be representative of the magnesium-rare earth element alloy group. Cerium was chosen as the solute because of its near-middle position in the series and because of its availability in the commercially pure form. A previously published description of the creep behavior of electrolytic magnesium" serves as the background to this research. The experimental approach used in that investigation has been partially repeated here. A series of binary alloys was planned to include the following: 1—A dilute alloy which would contain the cerium almost entirely in solid solution. This would assess the solid solution effect. 2—An alloy which is nearly saturated at the selected solution heat treatment temperature, 1070°F. Here the effect of nearly maximum precip- itation would be obtained without the influence of undissolved Mg-Ce intermetallic. 3—An alloy containing slightly more cerium than is soluble at 1070°F. This would allow the investigation of the effect of a small amount of excess intermetallic. 4—A high cerium alloy in which the influence of a large volume of undissolved intermetallic may be examined. Experimental Details In order to specify compositions of the binary alloy series a knowledge of the solubility of commercially pure cerium in solid electrolytic magnesium and also of the composition of the terminal intermetallic phase was necessary. The latter has been proven to be approximately Mg,Ce by Voge14 and Haughton and Schofield.5 A series of both cast and extruded alloys were solution heat treated 24 hr at 1070°F for a solubility determination. Lineal analyses of the polished and etched microstructures were accomplished with the aid of a Hurlbut

Jan 1, 1955

By A. W. Ashbrook

The process of solvent extraction.(or liquid-liquid extraction) is a separation technique involving mass transfer across a phase boundary, and as such is not limited to metal transfer from an aqueous to a non-aqueous phase, or, vice versa. We shall here, however, restrict ourselves to the application of the solvent extraction technique to metallurgical processing. Basically, the process of solvent extraction as applied to metals separation and purification requires only that a specific metal be transferred from, initially, an aqueous phase to a non-aqueous phase, followed by a reversal of this transfer. Such a process can be defined simply by the following equation: [M + E ME]

Jan 1, 1978

By Howard M. Wells

The investment worth of a mineral deposit can only be realistically evaluated in relation to specified engineering design criteria which fully detail the proposed method of exploitation. The operational design of a mine falls essentially within the technical discipline of the mining engineer, under the constraint that the technical design should be aimed at optimizing the financial attractiveness of the project. In the case of a marginally viable proposition it becomes vitally necessary to identify the best set of design parameters which together will add up to an optimum investment proposal. This paper examines some fundamental logic of optimization for a "wasting asset" type of investment such as a mine, with special reference to the rate of annual production and the strategy of selective mining.

Jan 12, 1978

By R. A. Flinn, John T. Norton

A considerable number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping capacity,'' might be a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail. Methods of Measuring Damping Capacity Many kinds of observations can be made upon a specimen subjected to a cyclic stress from which can be calculated the energy absorbed in

Jan 1, 1938

By R. A. Flinn, John T. Norton

A considerable number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping capacity,'' might be a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail. Methods of Measuring Damping Capacity Many kinds of observations can be made upon a specimen subjected to a cyclic stress from which can be calculated the energy absorbed in

Jan 1, 1938

By Dara P. Antia, Morris Cohen, Frank S. Gardner

THERE is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a specimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallographic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X-ray exposure and film-development conditions, a standard reference line is superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By R. N. Lambert

This chapter discusses the evolution of high-speed shaft sinking in the South African goldfields. Whether we are talking of an additional shaft at an existing mine or the opening of a new mine, the increasing depth of the ore-bearing reef and the unremitting inflation of costs have provided the compelling incentive to shorten the time taken to sink a shaft and start earning revenue. The high costs of sinking a modern shaft system in South Africa are indicated by the recent example of a deep-level mine in the Orange Free State where the cost was nearly $22!42 million. This was for a single large shaft of 33 ft 6 in. diam (in all cases, shaft diameters refer to the finished diameter of the shaft, e.g., inside the concrete) and 7600 ft deep with a prestressed concrete brattice wall dividing the shaft into upcast and downcast compartments. Higher costs and the consequent demand for increased tonnages, deeper shafts with higher rock temperatures, which necessitate highly sophisticaled ventilation and refrigeration requirements, have all accentuated the importance of time in a shaft-sinking operation. Rectangular shafts with their simple design and comparatively reasonable sinking speeds remained popular for many years until greater mining depths combined with a host of the other allied problems inevitably led to changes in shaft design. Circular shafts appeared to offer many advantages, particularly when considering ventilation, strength, mechanization, and sinking through bad ground and heavily watered zones. However, these advantages were largely offset by the slow rate of advance necessitated by the need to stop sinking in order to line the shaft. The development of the curb ring which enabled lining to take place above the bottom of the shaft and the use of multideck stages allowing sinking and lining to be carried out concurrently resulted in a major break- through. Rectangular shafts, which are still popular elsewhere, have been superseded in South Africa by circular shafts which are almost without exception the only shafts sunk in our goldfields today.

Jan 1, 1970

By W. G. Bearden, P. P. Scott, G. C. Howard

This paper concerns the rupture or breakdown of rock formations as related to drilling, completing, and stimulating production of wells, and comprises data compiled from a study of literature and records of treatment of oil and gas wells. and from tests conducted in bores drilled into rock cores and outcrops of rock. Results of the investigation indicate that the internal pressure to rupture cylinders of rock and to breakdown rock formations surrounding a bore in the earth is dependent upon the extent of intrusion of fluids. the position of bedding planes. the ratio of internal to external diameter, the tensile strength of rock, and magnitude of confining pressure, and is independent of the size of bore, degree of fluid saturation. and temperature of rock within practical limits. It is concluded that the mathematical relationship of pressure in bores and stresses in the surrounding rock must not be limited by the simplifying assumptions of homogeneity. isotropy, and impermeability; that the incidence of lost circulation of drilling fluids to induced fractures may be reduced by preventing intrusion of fluids into the small intrinsic fractures along weak bedding planes; and that the magnitude of the breakdown pressure of wells to be treated may be lowered by removal of mud cake. INTRODUCTION The purpose of this paper is to present and discuss the results of tests which may serve to broaden the understanding of the phenomena of rupture or breakdown of rock and thus contribute to the improvement of the techniques for drilling and completing wells. including such operations as preventing lost circulation, stimulating production, and placing cement. Since the early recognition of the possibility of rupturing rock adjacent to a well by fluid pressure, the distribution and magnitude of stresses around a well and the internal pressure to cause failure have been expressed mathematically by application of the principles defining the elastic and inelastic behavior of thick-walled cylinders of a homogeneous. isotropic, impermeable material. In either the elastic or plastic state, if the conditions of homogeneity. isotropy, and impermeability were the normal characteristics of rock. there would be no reason to question the validity of the above principles when applied to rock. However. since most rock formations are characteristically permeable to some degree, contain bedding planes and small intrinsic fractures. and are heterogeneous, rendering invalid the assumptions of homogeneity, isotropy, and impermeability, the application of the thick-walled cylinder theories to the behavior of rock formations penetrated by a bore appears illogical. Also the failure to consider the effect of the properties of the drilling fluids, which certainly intrude in various degrees into most rock formations. is further cause for questioning the application of these principles. Even in the case of cylinders of hardened chrome-nickel steel, which would he considered relatively homogeneous isotropic. and impermeable, as compared to rock, it has been observed that the internal pressure capable of being withstood by the cylinders varied with the sizes of molecules comprising the rupturing fluid used. Because of these apparent weaknesses in the theories of the behavior of thick-walled cylinders when applied to bores in rock, and the importance of knowing the true behavior of rock under the influence of fluid pressure when planning drilling and completing procedures for wells, tests were undertaken to determine by observation the actual rupturing pressure of cylinders of rock and the effects of such variables as environmental conditions and characteristics of rock formations, fluid properties, and bore dimensions. It was intended that by these tests the validity of the thick-walled cylinder theories when applied to rock would be determined and, if found invalid, mathematical expressions would be derived for predicting stress and rupturing pressure of rock formations under various conditions. Since the derivation of mathematical expressions has been only partially completed, all of the results of the latter phase are not included in this paper. PROCEDURE The investigation was initialed with a study of the theories pertaining to the rupturing of thick-walled cylinders of homogeneous. isotropic, impermeable material and a study of the

Jan 1, 1953

By Kenneth B. Ray, George R. Gardner

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent, investigation developed similar processes, which were successfully used in

Jan 1, 1939

By George R. Gardner, Kenneth B. Ray

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent, investigation developed similar processes, which were successfully used in

Jan 1, 1939

By C. N. Kravig

STANDARD raises at Homestake are 150 ft long. Raises of more than 150 ft, driven with the use of a cage and hoist, are considered long raises- some have been driven more than 900 ft. Long raises have eliminated the need for access drifts on each level when transfer and ventilation raises are driven. These timbered cage raises, 7x9 ft in cross section, include a rock compartment and a combination cage, pipe, and manway compartment. To prevent excessive weight on the timbers, 10x10-in. bearing beams are cemented into hitches cut in the rock at 150-ft intervals. The beams also hold back timber movement caused by daily drawing of rock through the rock compartment.

Jan 6, 1957

By H. S. Bell

IT SEEMS unnecessary to dwell upon the advantages of the modern pipe still as compared with the older type of distillation equipment used by oil refiners. The relatively low installation cost, coupled with remarkable operating efficiencies of pipe stills, precludes the consideration of other types except in rare instances where some peculiarity of product or plant may have an influence. The question of the actual heat required to distil petroleum is quite involved. We have extensive data on the latent heats of the various hydrocarbons under different conditions of pressure. We also have information regarding the specific heats of various oils and the effect of temperature thereon. Because of the complexity of petroleum and of each fraction, it seems impossible to theoretically analyze the partial-pressure effect of the great number of hydrocarbons upon one another during distillation. If a distillation curve and percentage analysis of any crude or product are available, it is possible to construct a curve with ordinates representing per cent. distilled and B. t. u. per pound or per gallon, or other desired unit. To do so the crude is split into fractions, of 5 or 10 per cent. The boiling point and gravity of each fraction being determined, it is possible to evaluate the heat required. As each fraction is removed, the residue must be raised to a higher temperature and latent heat supplied for the successive fraction. As the calculations progress, the latent heats decrease while the specific heats increase. Such a curve is illustrated by Fig. 1 for a typical 39.9 B° North Texas crude.

Jan 1, 1928

By B. H. Cody

THE Morenci concentrator of the Phelps Dodge Corporation is a part of the project that was completed after five years had been spent in development of the open-pit mine, equipment and process testing in the former No. 6 concentrator, and construction of the reduction works. The reduction works, of which the concentrator is a part, is about a mile and a quarter southeast of Morenci, on the highway that leads up Morenci Canyon. The concentrator has a nominal capacity for the treatment of 45,000 tons of ore daily. The original plant, which has a rated capacity of 25,000 tons of ore daily and is now in its fifth year of operation, began production on Jan. 30, 1942. The addition, to increase the capacity 8o pct, began operation on Dec. 1, 1943. The equipment of the original plant has been described in MINING AND METALLURGY (May 1942). No changes in equipment were recommended for installation in the concentrator extension and only one major change, forced by a shortage of maintenance labor, has since been made. Metallurgical treatment has been altered in some ways as experiments progressed and as labor and economic conditions dictated. No complete description of the operation of the concentrator has been published, so this paper will record such operating and equipment changes as have been necessary, the operating methods that have been developed and the metallurgical results that have been obtained. Descriptions are given in the order of the processes with a flowsheet and an equipment list of each process for convenient reference. The questions asked by engineer visitors have guided the detail in which operation and maintenance are described. During the period Jan. 30, 1942 to Sept. 1, 1946, ore milled has totaled 43,595,253 dry tons, from which 1,643,885 tons of concentrate have been made, containing an indicated production of 783,164,809 lb of copper. The principal results obtained in operation of the concentrator during the years 1942 to 1945, inclusive, and to Sept. 1, 1946 are shown in Table 1. A graphic general flowsheet of the plant is given in Fig I. ORE The Morenci ore that is now being treated is a medium-hard monzonite porphyry in which the principal sulphide minerals are chalcocite and pyrite. A minor amount of covellite is present. Chalcopyrite and bornite have been observed under the microscope. The chalcocite occurs mainly as a coating on pyrite. Some of the coatings are so thick that the pyrite presents the appearance of being an inclusion in chalcocite. Some are less than one micron thick and are barely visible at 500 diameters magnification of a polished cross section. Some chalcocite is present as a dissemination in the gangue. Various oxidized copper minerals are present as a result of oxidation in place but they represent a minor proportion of the copper minerals of the ore body. Oxidation

Jan 1, 1947

By N. A. Parlee, A. E. Lord

Measurements of the solubility of lead in liquid iron were made at 1550°, 1600°, 1650°, and 1700°C using two different methods, i.e., 1) liquid iron-liquid lead equilibration and 2) liquid iron-lead vapor equilibration. LEAD was long considered insoluble in liquid iron1. Today steels containing 0.15 to 0.35 pct Pb are used. One laboratory has found a solubility of about 0.5 pet in the 1600°C range. Recently Miller and Elliott2 gave 0.60 pct as the result of one determillation at 1540°C. Because these findings resulted from the

Jan 1, 1961

By J. B. Mackintosh

The general method which has been followed since the time of Heinrich Rose, and perhaps before, for the determination of phosphorus in iron and steel, is to dissolve the sample either in nitric acid, aqua regia, or some other oxidizing agent, in order to convert the phosphorus into phosphoric acid. In 1832 Rose* recommends HNO3, or aqua regia, preferably the former. Wohler, in 1854,† directs that the iron should be oxidized by burning in a stream of oxygen for the determination of carbon, and the resulting oxide of iron containing all the phosphorus as phosphoric acid be treated as an ore. In the fourth English edition of Fresenius' Quantitative Analysis,† pp. 666-667, we find directions to dissolve the iron in aqua regia or bromine; and, coming down to more recent times, we find F. A. Cairns § directing the employment of a boiling solution of potassium chlorate and hydrochloric acid for the oxidation and solution of the sample to be analyzed. It is unnecessary to multiply quotations from the literature of the subject, though they might be extended almost inclefinitely, since it would only be a repetition of the above mentioned series of methods in one form or another; and the references given have been selected to show how little essential variation there is in the type-methods of solution used. In fact it seems to be universally accepted as a necessary first step in the determination that some such method of solution should be followed. One chemist, however, struck out on a different line of thought, and to the Lest of my knowledge only one, M. V. Tantin, who, in

Jan 1, 1886