Search Documents

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

By D. Walton, B. Chalmers

A preferred orientation is known to occur frequently in the columnar zone of castings. This has been attributed to a preferred direction of growth. However, no satisfactory mechanism was proposed by which the preferred direction of growth led to the preferred orientation. The purpose of this work has been to establish this mechanism. It has been found that in general the observed preferred orientations only develop when the preferred directions of growth reveal themselves by dendritic growth. A mechanism based on this premise is found to be in agreement with the experimental data obtained in the course of this work. WHEN a liquid metal is allowed to solidify in a mold, it usually freezes in three stages, distinguished from each other by the size and shape of the grains. The first zone to freeze (the chill zone near the mold wall) consists of relatively fine grains that are equiaxed in shape and random in orientation. The next zone consists of crystals that are elongated in the direction of heat flow, i.e., normal to mold wall. These crystals are much larger in cross section than the crystals of the chill zone and have a very strongly preferred orientation. This is the columnar zone. The final zone, which is absent in very pure metals, is again equiaxed and randomly oriented, but usually has a much coarser grain size than the chill zone. The purpose of this study is to describe and account for the crystal size and orientation in the columnar zone. The occurrence of a preferred orientation in the columnar zone is well known, and in 1940, Greninger' suggested that it is apparently related to dendritic growth although at that time the only data were for metals with the face-centered-cubic structure. Table I shows that the direction of dendritic growth and the crystal axis that follows the heat flow direction coincide in all cases so far studied. The term "dendritic growth" is used here to represent the branched type of morphology that is characteristic of growth into supercooled melts.' In addition to the supercooling which is necessary before nucleation will occur at the mold wall, the necessary supercooling for continued dendritic growth can be provided in a mold by heat flow into the already formed solid at an interface whose Liquidus temperature is depressed by an accumula-

Jan 1, 1960

By Theodore Simons

(Butte Meeting, August, 1913.) DURING the last half century a great amount of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and slimes. The reason for this is that in almost every dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-clay to rework old dumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the nineteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of years, two general types of machines evolved for the treatment of fine sands and slimes : The so-called concentrators and vanners, on the one hand, and the buddies and round tables on the other.1 For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and economical than other machines.

Jan 7, 1913

By Wm. B. Price

The work of Leon Guillet concerning the effect of nickel on the structural properties of brass is checked. The best value for the coefficient of equivalence t, that is, the amount of zinc replaced by 1 per cent. of nickel, is shown to be-1.1 per cent. The best hot- and cold-working nickel silvers, varying in nickel content between the limits of 4 and 18 per cent., are tabulated and plotted diagrammatically. Also, some data are given showing a comparison between the physical properties of a hot- and cold-working low copper-nickel silver, and a commercial cold-working nickel silver containing approximately 8 per cent. more copper. THIS investigation of low copper-nickel silvers was undertaken to check the work of Leon Guillet on special brasses and to determine, more accurately, the effect of the addition of nickel on the microstructure of the binary alloys of copper and zinc. It was hoped that the results could be successfully applied to the practical production of low copper-nickel silvers. To explain the results of his investigations on special brasses, Leon Guillet evolved his conception of "fictitious compositions." He states,1 in his general conclusions, that on the introduction of a small amount of a third metal to a copper-zinc alloy, it enters into solid solution with the normal constituents up to saturation, but by so doing it brings the ternary alloy into a state microscopically equivalent to a binary copper-zinc alloy of fictitious composition, and physically more nearly like the latter than the brass containing copper-zinc in the ratio actually present. The physical properties of the ternary alloy, when compared to the same properties of an actual brass of the fictitious composition, are modified by the natural properties of the third element. Beyond the point of saturation, a special constituent appears and the above generalization no longer holds.

Jan 2, 1924

By Robert W. Fullerton, Barry G. McMillan, Donald T. King, Henning E. Soderberg

INTRODUCTION Dust control in coal preparation and related transport is a multi- faceted problem which must be anticipated whenever dry, fine coal is subject to rough handling which can disperse it in the air. This problem can be minimized by careful planning and proper design, by eliminating procedures which maximize dust production, and by utilizing the most appropriate dust-collection "hardware" for a given situation. Proper maintenance after dust-collection systems are installed is also very important, and will not only enable the selected equipment to perform properly, but will also reduce component wear, recover valuable product with the highest efficiency, provide cleaner and safer working conditions, and allow local clean-air standards to be met. This chapter is designed to provide basic information about dust control in relation to material processing and handling during coal preparation. Areas discussed should provide the reader with insight into basic dust-collection theory, particle behavior, equipment types, ductwork and hood considerations, general maintenance and design planning, and the economics of dust collection. Because of the wide range of areas covered and the various specialized problems inherent in each, the text is organized to be a practical reference, and not a complete, unabridged treatise of ventilation and dust-control design. Nevertheless, the information presented should be of value in both understanding and reducing problems of dust control in coal preparation.

Jan 1, 1979

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915; Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1983

By J. F. Kemp

CONTENTS. [ ] I. INTRODUCTION. 1. Situation.-From Monterey in the State of Nuevo Leon, the Sierra Madre mountains stretch away to the southeast and present a steep front to the northeast. The Monterey and Mexican Gulf railway, which connects Monterey with Tampico, follows their general line with its road-bed a few miles out from the foothills. At a distance of 100 miles from Monterey it passes through the town of Linares, and from Linares one can see far away to the southeast the peaks of another group of mountains

Jan 1, 1913

By B. C. Raynes

IN the early part of 1952, under the auspices of the U. S. Atomic Energy Commission, Horizons Inc. undertook an investigation dealing with the preparation of high purity thorium metal in order to develop an economically competitive production process for this metal based on a recovery of the metal by a fused salt electrolysis, since a survey of the literature of thorium chemistry indicated that electrolytic methods had not received much attention, despite the consideration that electrochemical production methods often offer attractive commercial potentialities. Thorium metal has been prepared by methods which fall into four general categories: 1) reduction of halides or double halides; 2) reduction of the oxide; 3) thermal decomposition of halides; and 4) electrolytic methods. Some of the important results obtained by various investigators since about 1900 in recorded attempts to prepare pure thorium metal are summarized in Table I. A bibliography of pertinent literature is included in this paper. Thorium is strongly electropositive and possesses a great affinity for oxygen and nitrogen. As a result the prospects for the production of high purity thorium from aqueous media or oxygen bearing compounds are remote. The most promising and profitable area of investigation for production of thorium metal lies in fused salt electrolysis. Thorium has been produced previously by this technique from halide salts in fused alkali chloride eutectic mixtures. Until recently, however, the lack of known large uses for thorium has inhibited the investigation of these methods. The basic problem in an investigation into fused salt production methods for thorium is to develop a suitable fused salt system for the economic preparation of thorium. The first portion of the work in these laboratories was a small scale investigation of the electrolysis of potassium thorium fluoride, KThF5, under a variety of conditions. High purity thorium was prepared in this manner, but the process did not appear to offer the simplest and most attractive continuous commercial operation. The work reported here relates to an all-chloride system employing thorium chloride as the cell feed. ThCL4 was produced as an anhydrous material stabilized in molten sodium chloride. This product, further diluted in NaCl, was subjected to electrolysis. The electrolytic process has been studied in cells capable of holding up to 50 lb total salt charge. Ductile, pure thorium metal has been reproducibly obtained in this operation. Considerable experimentation was carried out in the preparation of ThCL as a cell feed free from moisture, oxides, and other impurities. Thorium was cathodically deposited as a coarsely crystalline powder interspersed with residual bath salts. Aqueous procedures for separating and recovering the metal were developed. The thorium metal powder obtained has been evaluated with respect to its hardness, chemical purity, and certain other physical properties. Preparation of ThC1,—Thorium chloride, and the chlorides of some other metals (aluminum, beryllium, tantalum, zirconium, etc.) cannot be obtained from aqueous solution by direct heating and evaporation. Evaporation and heating of a solution of thorium chloride yields a hydrated salt or partially hydrated salt, and finally Tho,. Anhydrous thorium chloride is obtained by forming a hydrated ammonium chloride complex salt in acidified water solution, dehydrating this compound, and finally decomposing the double salt and subliming the ammonium chloride component. Various methods for the preparation of anhydrous thorium chloride, in accordance with this concept, were investigated as indicated in Table I1 from hydrated thorium chloride (ThCl, . 3H2O), and from thorium oxycarbonate (ThOCO,). In the method found most satisfactory for this work, thorium oxycarbonate was dissolved in an excess of concentrated HC1 to give a clear yellow solution. At least 2 mol NH,Cl were added to the solution per mol of contained thorium. Ammonium thorium chloride hydrate was crystallized from solution by cooling and saturation with HC1. The resultant complex, (NH,Cl),ThCl;xH,O, was dehydrated by evaporation at 130° to 150°C and thoroughly dried at about 250°C. The dried ammanium thorium chloride was then mixed with sodium chloride in proportions to form NaThCL or to produce a ThCL4-NaCl mixture with a given thorium content. The ammonium chloride was sublimed off at temperatures above 500°C in an inert atmosphere furnace to give an anhydrous chloride source electrolyte, essentially free of Tho, and of NKC1.

Jan 1, 1958

By Paul Foote

SEEBECK discovered, in 1821, that if, in a closed circuit of two metals the two junctions are at different temperatures, an electric current will flow in the circuit. In the case of an iron and a copper wire, for example, current will flow from copper to iron at the hot junction, or from iron to copper at the cold junction. Two factors combine to cause the current. An electromotive force exists between the two metals, the magnitude of which, depends upon the temperature and upon the metals; this is called the Peltier e.m.f. If a single wire of homogeneous material is heated at one end, an electromotive force is developed between the ends of the wire, the magnitude of which depends upon the metal and upon the difference in temperature; this is known as the Thomson e.m.f: The total e.m.f. acting in the circuit is the sum of the Peltier e.m.f. at the two junctions and the Thomson e.m.f. in each wire, consideration being given, of course, to the algebraic signs of the four e.m.f.'s. The total electromotive force thus depends upon the difference in temperature of the two

Jan 9, 1919

By B. W. Gandrud

WET-PROCESS coal-washing tables as we know them today have been in use in this country for approximately 25 years. The literature records only a few table installations worthy of note prior to adoption of the present-day differential-motion table. According to Phillips,' six Campbell bumping tables were being operated by the St. Bernard Coal Co., Earlington, Ky., in 11893. As late as 1923, according to Richardson, 2 72 such tables were in operation in the Rosedale washery of the Cambria Steel Co., at Johnstown, Pa. Bumping tables probably were not used to any considerable extent except in the plant at Earlington, and at two or three plants in Pennsylvania, but they may be considered as forerunners of the present-day coal-washing table. The transition from bumping tables to the type of tables now in use signalized a revolutionary change in table design. The advantages of the new design over the old were so outstanding as to make its adoption inevitable. BUMPING TABLES Bumping tables, as the name implies, utilized a bumping action for conveying the refuse and discharging it over the refuse end. The tables were hung from rods attached to overhead supporting beams. A shaft and cam arrangement at one end of the table served as the actuating mechanism and imparted to the table an endwise, back-and-forth, swinging motion. A bumping block was fixed in the proper position at the shaft end, so that the table would strike against it at the end of each backward swing. The hanger rods or stirrups were so adjusted as to give the table a slight uphill slope toward the refuse end; that is, the end next to the driving mechanism. The feed box was near the upper end, of the table and designed to spread the mixture of coal and water over the width of the table. Wash water was added a short distance below the feed box with the table in motion and coal mixed with water being fed to it through the feed box, a certain amount of stratification took place, depositing heavy refuse at the bottom of the bed in contact with the surface of the table. Constant bumping and a certain amount of

Jan 1, 1943

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute, since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1" to 2°C. per min. with or without slow stirring (Fig. I). By this method the lead-rich end of the lead-alltimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the liquidus curve of the binary alloys did not intersect at the euteotic temperature. An equivalent effect mas observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent in- vestigation by Pellini and Rhines,1 who determined the eutectic temperature to be 2 51.5°C. The observation that the curves of primarY crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomeilon by assuming the existence of a compound Sb4pb. He felt that supercooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3 the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature Of 2500 to 252°C. at a rate Of coo1ing of about 6°C. Per min. Abell Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic only 11 .4 to 11.5 per cent antimany. (Previous analyses by Stead4 .in 1891 gave 13 per cent.) Weaver,ll however, reported in 1935 that cooling cunres indi-

Jan 1, 1944

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute, since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1" to 2°C. per min. with or without slow stirring (Fig. I). By this method the lead-rich end of the lead-alltimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the liquidus curve of the binary alloys did not intersect at the euteotic temperature. An equivalent effect mas observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent in- vestigation by Pellini and Rhines,1 who determined the eutectic temperature to be 2 51.5°C. The observation that the curves of primarY crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomeilon by assuming the existence of a compound Sb4pb. He felt that supercooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3 the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature Of 2500 to 252°C. at a rate Of coo1ing of about 6°C. Per min. Abell Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic only 11 .4 to 11.5 per cent antimany. (Previous analyses by Stead4 .in 1891 gave 13 per cent.) Weaver,ll however, reported in 1935 that cooling cunres indi-

Jan 1, 1944

By Richard Thomas Newcomb

Chapters 5a, 5b, and 6 discuss the long- run supply of minerals and the characteristics of reserve search and production peculiar to extractive industries. It is now necessary to complete the picture by examining supply and demand in commodity markets to show how mineral prices are determined and how both price and production trends might be predicted over long periods of time. These practical interests can be served best by reviewing first some of the characteristics of the short-run static market models familiar to all readers of elementary economic texts, and then extending the theory to models of a more dynamic nature. It is important at the outset to note that economic theory provides a wide variety of economic models based on varying assumptions concerning the behavior of economic agents, the properties of the goods, the time period considered, and so on. Each variety of model offers certain analytical advantages and suffers certain shortcomings. The art of the applied economist or practioner lies in knowing enough both about the technology and practice of his problem and about theory to select the appropriate models for his analysis. In our approach it will be useful first to consider the role of markets for minerals and mineral products in relation to the efficient determination of what and how goods are produced in the whole economy, i.e., a general system of markets, before getting down to the task of analyzing supply and demand conditions in specific markets. The former study is called general equilibrium analysis, while the latter is called partial. By equilibrium is meant a state of the sys- tem under study in which supply equals demand in each market, and the prices which equilibrate the quantities offered and asked are called equilibrium prices. The tendency of prices to return toward equilibrium values if temporarily displaced, or to converge to new equilibrium values if important new conditions for supply or for demand are placed, defines "stable" equilibrium systems. The short-run describes a period in which adjustments to fixed capital are not made, although variable factors such as labor or materials can be adjusted. The long-run envisions a period in which fixed capital and other such constraints can be adjusted. Thus, it may take a sharp increase in price to bring out additional supply of a factor in the short-run with existing plant, while new capacity might permit additional quantities in the long-run without an increase in supply price.

Jan 1, 1976

By AIME AIME

THE Wednesday morning session was devoted entirely to the consideration of the tentative code for coal mine ventilation. A. W. Hesse is chairman of this subcommittee. E. A. Holbrook presided at the session and assisted by A. W. Hesse and George S. Rice, gave the historical background of the movement for a ventilation code. They stressed the point that this was to be an engineer's code, and that it was hoped that it might serve as a valuable guide to operating companies in securing greater efficiency as well as safety in ventilation. The discussion was continued into the afternoon session, and by adjournment the entire' code had been covered.' Many sections were referred back to the Committee for further study and several new sections were suggested. The various opinions and new ideas brought out during the discussion proved very valuable and. contributed much to the progress being made in the preparation of this code.

Jan 1, 1929

By M. Cohen

THERE seems to be a natural urge for the human mind to wonder about the beginning of things. When an explosion occurs, we immediately inquire "what set it off?" If a person contracts a disease, we are likely to ask "how did it happen?" On a much loftier plane, when we reflect about the universe, there is the inevitable question "what, or rather Who, started it all?" In principle, these varied queries have at least one attribute in common: they are attempts, whether earnest or casual, to search out the origin of events in nature. Accordingly, they involve not only scientific, but philosophical and even re1igious matters of deep concern. It is evident that, in a broad sense, the phenomenon of nucleation is enmeshed in this enticing concept of "the beginning", but we must extract the scientific component of the problem for our present purposes. Nucleation, as in the case of phase transformations, is best regarded from the standpoint of kinetics. There are then two main steps, which may come in either order: (a) Experimentally, one attempts to measure the frequency with which transformation centers spring into existence; and (b) theoretically, one seeks a model that will account for this observed birth-rate. Temperature, composition, strain, and prior history are some of the important variables that must be considered both experimentally and theoretically when dealing with nucleation in the solid state. Such interaction of theory and observation is an integral part of science in general, but it is particularly significant in the nucleation problem because the very beginning of a phenomenon invariably occurs on too localized a scale in both space and time to be detected with available techniques. Thus, there is little hope of making direct measurements on the nucleus during its birth or to ascertain the exact nature of the process; one can only infer the details of nucleation from the model whose predicted behavior seems to harmonize best with the measured rate of nucleation and its dependence on known parameters. In the field of solid-state nucleation, both theory and experiment call for much ingenuity, but somehow the conceptual schemes have spawned faster than they can be tested by observation. This is not to say that there are many basically new ideas in modern nucleation theory; rather, as we shall see, it is because the required fine-scale measurements are of immense technical difficulty. Quite likely, some of the nucleation models existent today have survived only because of the latitude permitted by meager data. There is great need to bring theory and experiment into better balance in this important area of physical metallurgy. Although one can

Jan 1, 1959

By Robert S. Archer, Zay Jeffries

It is about fifteen years since the development in Germany, largely by Alfred Wilm, of the aluminum alloy called duralumin. In this alloy, combining as it does the tensile strength of mild steel with the lightness and corrosion resistance of aluminum, a distinctly new material was presented to the engineering world. Despite the evident usefulness of this material, however, its commercial development has been slow, due in part to the difficulties involved in its fabrication. In view of the potentially great utility of strong aluminum alloys, it seemed desirable to find means of producing such alloys with better fabricating properties, and work was undertaken with this object in the laboratories of the Aluminum Company of America several years ago. This work has resulted in the production of two new types of aluminum alloy of the "strong alloy" class, having distinctly improved fabricating qualities. The knowledge gained has also made it possible to produce alloys of the duralumin type with greater strength and hardness than previously obtained. There have thus been made available some new engineering materials which it is the object of this paper to describe. These alloys, induding duralumin, are fundamentally wrought alloys. Castings of the same compositions heat treated in the same manner give inferior physical properties, particularly as to ductility. The statements made subsequently concerning properties and heat treatment apply to material that has received sufficient working to thoroughly break down the cast structure. The material referred to has, in general, undergone a reduction in section of at least 80 per cent, by mechanical working. It may be mentioned in passing that other compositions have been found that are suitable for the production of the maximum physical properties in heat-treated castings.

Jan 1, 1925

By Alexander Field

The hot-rolling properties of a series of high-sulfur steels are described. From a consideration of the sulfur, manganese, and zirconium contents of these steels, it is shown that zirconium reacts with the sulfur content of molten steel in accordance with the equation Zr + 2S = ZrS2. Zirconium disulfide appears in the finished state as gray-colored inclusions, similar to manganese sulfide in plastic behavior and general appearance. Zirconium completes its act of deoxidation before proceeding to combine with sulfur and indirectly increases the effective sulfur-combining power of any manganese which may be present. IN A previous paper,1 the experimental methods used and some of the results obtained in an extensive investigation of steels containing zirconium were described. The present paper considers in greater detail one of the most interesting of these effects, namely, the elimination of "red shortness" and the occurrence in steel of a compound of zirconium and sulfur. A consideration of the actual percentages of zirconium, manganese, and sulfur in numerous steels in the light of behavior during rolling has led to new conclusions of the most practical import regarding the reciprocal relationships of these elements. The microscopic examination of high-sulfur steels containing zirconium has also been productive of interesting results. Before discussing the experimental data in question, it may be stated, briefly, that the reaction between zirconium and sulfur in molten steel may he represented by the simple equation, Zr + 2S = ZrS2, and that the zirconium sulfide thus formed occurs in the finished steel in the form of gray-colored inclusions, closely resembling manganese sulfide and, like the latter, exhibiting plasticity at rolling temperatures. Molten steel containing zirconium retains such a negligibly small amount of oxygen in solution that the foregoing reaction goes to completion.

Jan 2, 1924

Electro-mechanical actuator, self-protected for mechanical and electrical overload, is developed by RACO. Tubular housing consists of squirrel cage motor with hollow rotor shaft and inner threads in the rotor. Features stroke distance of 2-72 in. and wide range of trust (20 lb-10 tons). (100) Agglomeration systems, offered by Ferro-Tech, incorporate pelletizing, briquetting and extrusion systems to agglomerate materials too fine to convey, load or feed to a process. Equipment includes disc and drum pelletizers, briquetter presses, compactors, extruders, pugmills and mixers, dryers, coolers, feeders and conveyors. (101)

Jan 9, 1973

By Frederick Beckett

WIDESPREAD experimentation has been conducted in recent years to devise a means of preventing intergranular corrosion in austenitic chromium-nickel steels of the 18 per cent chromium-8 per cent nickel type. Additions of titanium to these steels have been used commercially to overcome this difficulty, as advocated by Krupp of Germany, and the latest literature reference concerning improved details of this method is the article by Bain, Aborn and Rutherford.1 Extensive work by the present authors has shown columbium also to be a particularly valuable agent for inhibiting intergranular corrosion. This paper does not deal with steels that are largely or wholly aus-tenitic ; it is limited to a discussion of the results obtained through the use of titanium and columbium in plain high-chromium steels. For many years titanium has been used commercially by some steelmakers as a cleanser, and to a lesser extent as a hardener, but then in greater per-centages. The results of the work to be described disclose that titanium and columbium in proper proportions act as effective softeners in the high-chromium steels. It is well known that chromium intensifies the hardening effect of carbon in steel; it imparts pronounced air-hardening properties within a rather wide range of chromium content; it provides increased ductility in steels of given strength and hardness; and it enhances resistance to corrosion and oxidation at elevated temperatures to a marked degree. However, in applications requiring a combination of some of these valu-able properties great hardness is frequently a detriment rather than a merit. When the objective is a soft and ductile steel having optimum corrosion resistance, the producer strives for a carbon content as low as commercially practicable.

Jan 1, 1933

By Harmon F. Fisher

In the course of a comprehensive investigation for the development of the electrical process for the dehydration of oil-field emulsions, the writer has had an unusual opportunity to direct and execute a number of related, parallel studies concerning crude oil emulsions and extending over a period of nearly six years. Among these was an investigation utilizing the microscope for studying both the general characteristics of crude oil emulsions, the nature of their electrical charge and the action of an alternating current field in causing coalescence of the finely dispersed, more or less permanently suspended, emulsion particles into larger droplets of such mass that subsequent dehydration would follow by the ordinary process of settling, further agglomeration of the water droplets and, finally, separation into commercially dry, pipe line oil and a clean water discharge. It is not the purpose of this paper to enter into a detailed discussion of the highly specialized subject of microscope technique, nor into a theoretical discussion concerning the origin of the electrical charge on the emulsion particle or concerning the mechanism of the electrical phenomena occurring during the electrical treatment of oil-field emulsions. In a short paper of this character one can hope to touch on only a very limited discussion of the theoretical aspects of crude oil emulsions. The subject of emulsions and colloids is comprised in a comparatively young science in which, however, very rapid progress is being made and consequently it is undergoing many changes; a tentative conclusion valid today may be overthrown tomorrow. Nor would it be a simple science even if it were no longer undergoing this rapid progress; a thorough study of emulsions is based upon a knowledge of such fundamental subjects as molecular structure, ionization and other electrical phenomena, surface chemistry, surface and interfacial tension phenomena, viscosity and other factors too numerous to discuss here and the fundamental theories of which are still undergoing more or less change. Therefore this paper will confine itself largely to a generally descriptive discussion, a sufficiently detailed outline of the microscope technique and a brief comment on

Jan 1, 1931