Search Documents

By G. R. M. Del Giudice

A survey of the flotation literature of the past 10 years indicates an increasing use of the microscope as a tool for investigation. Thus, the metallurgical microscope has been used by Tucker and Head;' Taggart, Taylor and Ince;2 Ince,3 and del Giudice4 to examine mineral surfaces that had been subjected to the action of various flotation reagents and to the action of slime pulps. It has also been used by Gaudin, Groh and Henderson;5 Martin;6 Morrow and Griswold;7 and others to examine bakelite briquets of mill products. The microscope with transmitted light, both with bright-field and dark-field illuminations, has been used by Taggart, Taylor and Knoll8 and by Ince9 to observe Brownian motrement and flocculation in flotation pulps. The use of the microscope at low-power magnifications with incident illumination for the examination of mill products has been known for years.10 Finally, del Giudice11 has used a relatively new type of illumination, the Ultropak, for the examinntion of slime-coatings.

Jan 1, 1935

By H. J. French

WITHIN the past few years, particularly because of the rapid growth of the airplane industry during the war, considerable attention has been paid to the manufacture of light-wall cold-drawn seamless and welded steel tubing for structural purposes. While the manufacture of such tubing is not, in itself, a difficult matter, some difficulties have. been encountered in producing the same under specifications requiring definite physical properties. It is the purpose of this paper to describe the methods of manufacture and the properties that may be obtained by such methods for tubing coming within about ½ to 2 in. (12.7 to 50.8 mm.) outside diameter and 10 to 22 Birmingham wire gage (0.134 to 0.028 in. wall thickness). Such tubing is largely used as structural material in the aircraft industry, and it is of the utmost importance that the physical and chemical properties should be known, and also that the various factors entering into the manufacture should be under such control as to allow these properties to be varied and held within definite limits. In general, tubing may be divided into four classes: namely, specialty tubing, such as riveted-sheet or plate, lock jointed, etc.; brazed tubing; welded tubing; and seamless tubing. Welded tubing may be divided into hot product, such as lap welded and butt, welded, and cold product, such as acetylene and electric welded. Seamless tubing may be hot rolled or cold drawn.

Jan 9, 1919

By M. A. Mahtab, J. D. Dixon

The results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block- caving method are presented. The two-dimensional finite-element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1977

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles L range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola 1 described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes2 in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of stationary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker3 was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It could handle

Jan 1, 1943

By S. Marion Tucker

THE aggregate number of "papers" read within any one year before more or less bored and bewildered audiences is simply appalling. We have seventy to eighty engineering societies alone, not to speak of the many hundreds of societies of every other imaginable kind. And each meets at least once a year to tell what it has found out since the last meeting. All this is very fine and fortunate, at least in the case of the scientific and technological societies; for if even only one significant discovery, one new truth, one new idea comes out at the meeting, the session has been abundantly justified. To many of us, not scientists or technologists, the scientific and technological societies seem to release by far the most useful and important information. What they have to say is often of prime importance directly to human life and to industry, and is perhaps even more important indirectly in its final influence upon social and economic conditions, thus ultimately determining the course of what we like to call civilization. The paper read by that quiet, unpretentious man on the platform ma; mean the revolutionizing of a great existing industry, the creation of an entirely new industry, the gain of millions of dollars to some persons, the loss of millions to others. But, lamentably,

Jan 1, 1940

By A. F. Meger

REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal Co. who have helped develop, over a number of years, an efficient and flexible method for spraying con- trolled amounts of oil on coal. Since the George- town preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage.

Jan 7, 1954

By L. L. Wyman

SINCE the observations of Heyn,1 relative to the embrittlement of copper after having been heated in hydrogen, this subject has received considerable attention from later investigators. The published works of Archbutt2 and of Bengough and Hill3 give the reasons for this embrittlement-the formation of steam by the reaction between cuprous oxide and hydrogen. From Ruder,4 Pilling,5 Moore and Beckinsdale,6 Bassett and Bradley,7 and from Smith8 can be obtained quantitative data concerning the action of hydrogen and other reducing gases on copper samples having various oxygen contents. This problem has been discussed from a practical standpoint by Fuller9 who calls attention to some of the instances of this embrittlement encountered in the manufacturing field. The examples he cites may be considered typical cases of copper embrittlement which were incident to the process of manufacture. In many cases, such difficulties are overcome by changes in the manufacturing process.

Jan 1, 1931

By W. C. Phalen

INTRODUCTION NOBODY will dispute the fact that the conservation in every legitimate manner of our valuable high-grade phosphate-rock deposits is a present-day problem of importance. The table and curve, given herewith, show. that during the past 10 years the exportation of high-grade rock has averaged very close to half the total output of the entire country. The bulk of this exportation is from Florida, for obvious reasons. It is plain that the deposits in this State, more particularly, are being wastefully depleted under a system of selecting the cream of the product for exportation to Europe, leaving the comparatively low-grade rock, running from 65 to 70 per cent., and under, in bone phosphate of lime, for our own n fertilizer manufacturers to work up when all the best rock is gone. In this paper the writer has endeavored to make a point of describing in some detail the important methods of production and conservation in Tennessee. These ought to prove of educational value to our American agriculturists and fertilizer manufacturers, and should result in a demand for the highest-grade rock, both for direct application to the soil and for use in making acid phosphate. It is certainly evident that the European

Jan 10, 1916

No phase of the steel industry is more typical of its remark- able progress than is the evolution and development of the modern American blast furnace. The founding of the Institute in 1871 also marked the beginning of a new era in the pig-iron industry. The rapidly expanding westward development of the country, with its seemingly unlimited markets, gave rise to unprecedented demands for blast-furnace products. The manner in which the iron industry responded provides a fascinating chapter in the history of industrial development. Prior to this period, the iron industry of the United States, largely concentrated in the East, was based upon the consumption of local iron ores and local fuels, the latter predominately charcoal and anthracite. Small, isolated furnaces were located near scattered ore and fuel sources, and the completely integrated ironworks and steelworks were yet to be developed. In about 1860 exploitation of the newly discovered rich ore deposits in Michigan and the successful adaptation of blast furnaces to coke produced from coal of the great Pittsburgh seam in western Pennsylvania proved to be major factors in firmly establishing the general westward shift of the industry. But these were largely economic in character, and it was not until about 1870 that the aggressive, individualistic nature of the ironmaster asserted itself in no uncertain manner. No longer limited by relatively inadequate equipment and inferior raw materials, and spurred as well as encouraged by those who supplied capital for these new enterprises, furnacemen began to establish unheard of records in iron production. It is not surprising that Pittsburgh was the center of this new activity. Its tenor is best indicated by the following account :l

Jan 1, 1948

By R. J. Wasilewski

Electrical resistivity variation with temperature was measured on a series of alloys containting up to 33 at. pct of oxygen over the range 77° to1500°K. The resistivity behavior is highly anomalous and itzconsistent with simple metallic conduction. Both composition and temperature-depended resistivity singularities were observed. A few experiments carried out on Ti-N and Zr-O alloys indicate the presence of similar anomalies. These observations, together with the published data on effects of substi-tutional alloying on the resistiuity of titanium, suggest that the anomalies are inhevent in the electron structure of this group oj metals. The existence of two-band conduction, and a significant shift of bands relative to each other with temperature and/or the electron concentration are suggested. CONSIDERABLE advances have been made in recent years in the alloy theory of simple metals. Very little, however, is known about the bonding in transition metals and their alloys.&apos; Titanium, with its relatively few electrons, may be expected to show simpler alloying behavior than the more complex transition elements. Its alloys with the interstitial elements appear particularly attractive in an investigation of bonding characteristics because of a) the simple nature of the solute elements, b) the remarkable similarity between the equiatomic structures Tic, TiN, and TiO, and c) the extensive solid solubility ranges of oxygen and nitrogen in a titanium reported.2,3 The Ti-O system was chosen for the most extensive investigation because of the relative ease of preparation of suitable specimens. Since the main object of the work was to obtain data on the bonding and its changes on alloying, electron-sensitive properties were primarily investigated. The present work describes the investigation on the electrical resistivity-temperature-oxygen content relationships. A few experiments were also carried out at selected compositions in the Ti-N and Zr-O systems. EXPERIMENTAL Materials and Method. Polycrystalline specimens were prepared in the form of hairpin strips some 50 by 5 by 0.15 to 0.50 mm by direct metal-gas reaction. This was carried out by controlled oxidation followed by a homogenizing anneal at a higher temperature. All the test specimens were fully homogenized as judged from the uniform microstructure and microhardness. To avoid preferred orientation, each strip specimen was annealed in the ß range prior to the oxidation, this procedure assuring random orientation in the strip;4 hence any texture resulting from the oxidation reaction itself affected all the specimens to a similar extent. Titanium used was of high purity (66 DPN, 10 Kg load; major impurities 0,-43G ppm, N,-70 ppm, C-25 ppm, Fe-14G ppm). The solute content of the alloys was determined by weighing, after the reaction with a known amount of oxygen. The specimens in which the discrepancy between the volumetric and gravimetric measurements exceeded 2 pct (or 0.2 mg for the low oxygen alloys) were rejected. The mean between the two measurements was then taken as the oxygen content of the alloy. Check analyses showed no measurable nitrogen contamination. All oxygen contents are given in atomic percent. Zr-O alloys were prepared in identical manner from hafnium-free crystal bar metal, cold-rolled to strip 0.25 mm thick. Ti-N alloys required very long reaction times at the maximum temperature available (1250°C). In order, therefore, to detect possible oxygen contamination, duplicate specimens were reacted in every experimental run, and one of these was analyzed both for oxygen (vacuum fusion) and for nitrogen (Kjeldahl). Only the specimens in which the check analysis showed < 1000 ppm O were then used for resistivity investigation. Since only relatively high nitrogen alloys (7.1 at. pct; i.e., 2 wt pct N,) were investigated, this oxygen contamination was considered permissible. Dc resistance was measured by the four-probe method as previously described.= The temperature was determined with a calibrated thermocouple placed in the center of the specimen hairpin. The errors in the specimen resistance values thus obtained were estimated at 1 pct due almost exclusively to the finite thickness of the potential wires and the consequent uncertainty as regards the true resistance length of the specimen. For the calculation of the specific resistance, however, no dimensional measurements could be carried out on most of the

Jan 1, 1962

By Archer E. Wheeler

IN the copper industry, the year 1942 was one of striving for larger tonnage and increased production. The demands of the war program placed copper high in the list of strategic metals and the Government encouraged production by offering a premium of 5c. per pound for copper output in excess of the 1941 quotas. This had the effect of increasing the tempo of existing operations and also of initiating a number of projects which will eventually result in production from sources not hitherto exploited. No radically new methods of copper reduction were reported.

Jan 1, 1943

By Harold Roast

THE object of this investigation was to compare the arsenical antimony-lead alloy with some of the regular bearing-metal alloys. With this end in view, the following tests were made: 1. Chemical analyses to show the composition. 2. Thermal analyses. 3. Macroscopic examination of fractures. 4. Microscopic examination. 5. Tensile tests. 6. Crushing tests. 7. Scleroscope tests. 8. Brinell tests, at temperatures from 80° to 400° F. Tests 3 to 8 were conducted on both sand-cast and chill-cast specimens. For the purposes of this paper the alloys have been numbered from 1 to 6; their composition is as follows: LEAD, ANTIMONY, TIN, COPPER, ARSENIC, NUMBER PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. 1 82.64 12.95 4.40 0.01 none 2 27.54 9.94 59.87 2.65 none 3 77.65 20.75 none 0.13 1.47 4 82.95 16.85 none 0.20 none 5 83.78 15.35 none 0.05 0.82 6 0.15 7.87 84.13 7.85 none The analysis, in the case of the antimony, was made by solution in sulfuric acid and titrated with permanganate. For tin, the ferric-chloride method was used; for copper, the alkaline separations, and the thiocyanate methods; for arsenic, volatilization of arsenic and titration with iodine. The lead, with the exception of alloy 6, was taken by difference.

Jan 2, 1922

By John L. JR. Schroder

INTRODUCTION-SYSTEM DESIGN The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights ; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same

Jan 1, 1981

On the following pages are abstracts of papers published by the Institute during the year 1934 as TECHNICAL PWLICATIONB, CONTRIBUTIONS, m bound volumes and in MINING AND METALLURGY. For abstracts of papers that appear In bound volumes in 1934 but that were published as TECHNICAL PWLICATIONS m 1932 or 1933, see the TRANSACTIONS for 1932 and the YEAR BOOK dated January, 1934. Many of the TECHNICAL PWLICATIONS have been reprinted In bound volumes Information regarding this disposition, and number of pages in each paper, may be found m the list beginning on page 92 Volume numbers are given as listed at the beginning of the index, page 99 The abstracts are grouped as follows:

Jan 1, 1935

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes&apos; in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of station¬ary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker&apos; was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It &apos;could handle

Jan 1, 1943

By John C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert, Russell, Le Conte, Spur, Louderback, and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea.

Jan 3, 1960

Aalde, Kaare. (&apos;40) Gen&apos;I Del., Bisbee. Ariz. Aase, Glenn D., (&apos;40) Univ. of North Dakota. Grand Forks. N. D. Abadesco, Enrique A., (&apos;39) College of Engrg.. Univ. of the Philippines. Manila, P. I. Abbott. John L., (&apos;40) Colorado School of Mines. Golden. Colo. Abdul-Ahad, A., (&apos;39) Montana School of Mines. Residence Hall, Butte. Mont. Abreu, Ovidio M., (&apos;38) Univ. of Nevada, Reno, Nev. Acomb, Allen. (&apos;41) Louisiana State Univ., Box 1970, University. La. Acosta S., Gonzalo. (&apos;40) Univ. of Texas, Univ. Sta., Box 1785. Austin, Tex. Adam, Howard W., (&apos;41) Montana School of Mines. Butte, Mont. Adams, Albert, (&apos;381 New Mexico School of Mines, Socorro. N. M. Adams. Charles W., (&apos;39) Michigan College of Min. & Tech., Houghton, Mich. Adams. H. Travis, (&apos;39) 316 South -5th St., Bur¬bank. Calif. Adams, Jack L., (&apos;39) Univ. of Oklahoma, Nor¬man. Okla. Adams. John W., (&apos;41) Colorado School of Mines, Golden. Colo. Adams. Lewis J.. (&apos;39) 402 Del Mar Blvd., Corpus Christi, Tex. Adams, Rob L., (&apos;40) Agricultural & Mech. Col¬ lege of Texas. Box 600, College Sta., Tex. Adamson. Charles R., (&apos;41) Univ. of Utah, Salt Lake City. Utah.

Jan 1, 1941

By A. J. Hendron, D. U. Deere, F. D. Patton, E. J. Cording

In the design of structures founded in the near-surface rock, a distinction may be made between those problems that are related to the strength of the rock mass, and those that are related primarily to the compressibility of the rock mass. The mining engineer deals almost exclusively with problems involving strength in the design of open-pit slopes and underground openings. The civil engineer is similarly concerned with strength problems in the design of vehicular and water tunnels; underground power plants; cut slopes in rock for highways, canals, and spillways; and in the study of the sliding resistance of the foundations of gravity dams and the abutments of arch dams. Moreover, the civil engineer encounters problems in which the compressibility of the rock becomes the key element in the design. These problems include settlement of heavy structures supported on rock, deformation of the abutments of arch dams, and deflection of pressure tunnel linings. The design problems listed above are still solved largely on the basis of experience and rule-of-thumb. However, recent developments in rock mechanics give promise of providing more realistic approaches to certain aspects of the design. This paper, presents some of the more important recent developments which contribute to an understanding of rock behavior and which aid in design of rock structures. Typically, four steps are involved in the design of a structure, whether it be a machine element, a structural member of a building, or a structure in rock. These steps are listed below:

Jan 1, 1967

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Mar. 10, 1917, to Apr. 10, 1917. ADKINS, HARVEY S Adkins & Denham, Engineers, Box 291,. Hazard, Ky. ANDERSON, ARTHUR P .... Leaser, Gibson Copper Co., Box 1978, Miami, Ariz. ARNOLD, EDWARD C... Min. Engr., Chief Engr., Federal Lead Co., Flat River, Mo. ASKIN, THOMAS B. H., Ball Mill Expert, Inspiration Cons. Copper Co., Miami, Ariz. BAIN, C. KREMER Butte & Superior Mining Co., Butte, Mont. BAKER, WILLIAM A.,.JR., Vice Pres. & Sales Mgr., The Georges Creek-Parker Coal Co., 306 North Gay St., Baltimore, Md. BOOTH, GEORGE H Mech. Engr., Inspiration Cons. Copper Co., Miami, Ariz. BRIDGMAN, G. TEMPLE, Asst. Consulting Mining Engr., Guggenheim Bros., 120 Broadway, New York, N. Y. BROOKS, CHARLES A Mine Surveyor, Homestake Min. Co., Lead, So. Dak. BUTCHER, FREDERIC E., Secretary, Missouri Metals Corpn., 1945 Railway Exchange Bldg., St. Louis, Mo.

Jan 5, 1917

By Erland Johnson

BRINE was discovered at Avery Island, La., in 1790, but it was not until 1862 that rock salt was found about 13 ft below surface-the first discovery of rock salt on the continent. Maximum elevation of the island is 152 ft and elevation at the shaft 31 ft. The mining level is 530 ft below elevation at the shaft and the shallowest salt about 12 ft below surface. A shaft was sunk in 1869 when the mining operation started. In 1898 the present shaft was sunk, and the mine has been operated by International Salt Co. ever since.

Jan 6, 1957