Search Documents

By Roy J. Helfinstine, Gilbert H. Cady

One of the most urgent needs in the field of coal combustion is the ability to predict the performance of a coal from knowledge gained from small-scale tests. Numerous types of analyses and tests are conducted on coal, including the proximate and ultimate analyses, heating value, varieties of sulphur, ash analysis, ash fusion temperatures, free swelling index, petrographic analysis, and Gieseler. plasticity. The Illinois Geological Survey has made an intensive study of the value of these tests for judging the performance characteristics of the coal as actually utilized. To date, three reports1,2,3 have been issued, and another is being prepared. The present paper briefly summarizes some of the results found in the studies. Equipment The equipment used for the tests is described in some detail in the above mentioned publications. Briefly, it consisted of a domestic stoker, cast-iron boiler, and water-cooled heat exchanger, which were operated as a forced circulation hot-water system. The entire unit was mounted on scales. Instruments for recording the per- formance of the coal included a hot-water meter to indicate the quantity of water flowing through the boiler; a two-pen, mercury-actuated thermometer to record the temperatures of the water entering and leaving the boiler; a chemical-type meter to record the percentage of CO2 in the stack gases; a pressure gauge to record the static pressure in the stoker-air duct; and a multipoint potentiometer to record the temperatures in the stack and room, and the opacity of the stack gases. A 16 mm motion picture camera was available for taking pictures of either the fuel bed or the scale dial. Procedure The tests described in this report can be conveniently divided into three phases. For the first phase, a load of 5 or 6 tons of unwashed coal (usually screenings) was obtained from each of fourteen Illinois mines. These coals were all crushed and screened to a size of 35 in. (square hole) by 8 mesh. Combustion tests were made on a part of this raw, screened coal. Another portion was passed over a concentrating table to reduce the ash to what was considered to be commercially reasonable, and combustion tests were made on this upgraded coal. The ash content of the remaining coal was reduced to a still lower figure by passing it over the washing table with greater reject, or by standard float-sink procedure. This cleaned fraction was then tested in the stoker-boiler unit. Thus three coals with varying ash content were tested from each mine. For the second phase reported here, coals were obtained from four Arkansas mines and tested as received and after passing over the concentrating table with a normal reject. One Illinois coal was tested in the "washed" condition only. The third phase included tests on commercially prepared stoker coals

Jan 1, 1950

By Walter Miller

ALTHOUGH confident of its ability to meet any demands which may be made, the petroleum refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full co-operative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor within the industry and the means for gearing that endeavor in full harmony with the nation?s needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned.

Jan 1, 1942

By Eugene Ayres

This study is concerned primarily with a backward look at the projections made in the Report to the President by the President's Materials Policy Commission issued in June 1952. Only a few years have elapsed since the date of this report, but definite statistics available then were often not later than 1947. Today we have figures for the intervening years through 1957-virtually a ten-year span. What, if anything, has happened during this decade that was unexpected or wrongly appraised? In the light of more recent data and trends, will we be justified in modifying the longer-term predictions made in 1952? This study will attempt to answer such questions. Major sources and forms of energy will be considered from the standpoints of ultimately available amounts and the rates of production and demand. Electricity: The PMPC projections were made on the basis of an unexpected growth of about 10 pct per year. This was at a time when some experts in the field were assuming growth rates of not more than 8 pct.

Jan 1, 1960

By W. C. Meyer

In an effort to conserve and extend oil resources, the use of powdered coal-in-oil mixtures (COM) as an alternate fuel in oil-fired boilers is receiving increasing attention. For the approach to be successful, some degree of stability of the suspension against settling is needed. The variety of means available to achieve stability of this nonaqueous slurry is reviewed along with some of the physical and chemical concepts which underlie each method.

Jan 1, 1983

By David A. Keys

The actual procedure in estimating depth of overburden from magnetic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anomalies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1"4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k'/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k'/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision. The correctness of the theoretical calculations may be checked in two ways. The first is to make laboratory models of various known shapes and pole distributions, to calculate the anomalies to be expected

Jan 1, 1940

By David A. Keys

The actual procedure in estimating depth of overburden from magnetic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anomalies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1"4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k'/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k'/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision. The correctness of the theoretical calculations may be checked in two ways. The first is to make laboratory models of various known shapes and pole distributions, to calculate the anomalies to be expected

Jan 1, 1940

By Peter N. Calder

This paper deals with the reinforcement of igneous rock slopes at three open pit iron ore trines in northern Canada. The pits involved utilize overall slope angles in excess of 60º with ultimate depths in the order of 250 m. Three case studies are described. The first concerns the reinforcement of a 300,000 Ton undercut rock wedge, approximately 70 m in height. This was accomplished using 20 cm diameter steel bales, installed in 25 cm diameter vertical holes, and a cement-sand grout. The second involves the reinforcement of a 40 m wide diabase dyke which had been continuously failing as the pit deepened. A unique form of rock reinforcement was used in that the entire mass of the undercut dyke was not pinned to the wall. Rather an interlocking effect between individual blocks within the dyke was relied upon. A third concerns the reinforcement of a berm which was undercut by the contact between the ore and waste. This reinforcement was also accomplished using a combination of steel bales, rods and cement grout.

Jan 1, 1982

By Joseph A. Holmes

(Pittsburg Meeting, March, 1910.) AT the Mining Experiment Station of the U. S. Geological Survey, in Pittsburg, an investigation of the process of combustion is being carried on in a specially-designed furnace having an unusually long combustion-chamber. This work is conducted by a committee consisting of H. Kreisinger, mechanical engineer; Dr. J. C. W. Frazer, chemist; and Dr. J. K. Clement, physicist. The problem, essentially one of physical chemistry, is extremely interesting to all who are concerned in the burning of coal or the construction of furnaces. The main object of these experiments is to ascertain the relation between the amount of the volatile combustible driven from the coal and the combustion-spaces necessary to burn it completely. Our best steam-coals vary from 15 to 45 per cent. of fixed combustible. The greater part of the latter is burned on the grate; but the volatile combustible leaves the freshly-charged coal and must be burned in the combustion-space. If this space is not large enough, the volatile combustible will leave the furnace only partly burned, and the result will be a considerable heat-loss and a smoky stack. Strictly speaking, the factor which determines the completeness of combustion of the volatile matter, after it has been mixed with a certain amount of air, is the length of time the mixture is allowed to remain in the combustion-space; but this length of time depends on the extent of the space itself. Let us suppose, for instance, that, when a given coal is burned at a certain standard rate, the volume of the volatile combustible driven off per second is 10 cu. ft. Adding, say, 10 cu. ft. of air, the volume of the resulting burning mixture is increased to 20 cu. ft. If the combustion-space is 20 cu. ft., the burning mixture will stay in it,

May 1, 1910

By J. F. Evers, S. Sadiq, F. W. Preston, G. W. Swift

Proper scaling of unsteady-state flow in laboratory gas reservoir models can be achieved if the permeability/fractional porosity ratio is less than 0.5 md. Porous media meeting this specification can be obtained from mixtures of sand and Portland cement provided (1) the water/cement ratio is in the range of 0.35 to 0.40, (2) the sand/cement ratio is in the range of 1/1 to 2/1, (3) the sand grain size is in the range of 48-100 to 18-28 mesh, (4) the mortar curing time is 7 days or more and (5) the cured mortar is dried under vacuum to reduce the temperature level employed during the drying process. The areal homogeneity of the mortars tested is reasonably good, although significant trends in vertical permeability were noted. The Klinkenberg and non-Darcy coefficients of mortar are such that proper scaling of these effects in the laboratory model could be expected. INTRODUCTION A long term deliverability prediction for a gas well is generally based on data determined from flow tests that are of short duration relative to the producing life of the well. These data, together with an estimate of gas reserves in place, form the basis for establishing the parameters of the mathematical model used to predict performance at future times. Results obtained from a mathematical model represent only an interpretation of the physical process being modeled. Experimental verification of the production process from discovery to abandonment is needed where production occurs under carefully controlled conditions. Ideally, one might consider such an experiment to be conducted in the field. Even if the cost of such an experiment could be justified, the time required would make it impractical to consider. However, if the time scaling problem could be handled properly, an experimental model of the gas reservoir production process could provide the necessary data to study the mechanisms of the production process in a reasonable time period. An experimental model has been designed and constructed using the data of this study as a basis. The model reservoir system consists of one producing well located at the center of a right-circular cylinder of porous material. Ten to 15 observation wells are located at strategic offset positions from the producing well. These wells, and the producing well, are fitted with pressure transducers so that the pressure-time history can be recorded at various radial and azimuthal positions in the drainage area during the entire production life of the system. Time is scaled in the model so that the time required to produce gas from discovery pressure to abandonment pressure is about 2 hours. This compares with a 20-year producing life in the model's field counterpart and gives a time scale factor of approximately 1:100,000. DESIGN CRITERIA To establish design criteria for the experimental model, the reservoir is considered to be a finite right-circular cylinder of radius rr, and height h with a producing well of radius rw located at the center and completed through the producing formation. This reservoir consists of a porous medium which has a uniform permeability k and gas porosity and the gas contained in the reservoir has density p, viscosity µ and molecular weight M. Initially, the pressure at all points within the reservoir is uniform at po. and the reservoir temperature is T. Since the reservoir production process has been demonstrated to occur in two distinct transient modes for either Darcy or non-Darcy flow,l it is

By Bernard Moore

THE last few decades have witnessed the introduction of many new nonmetallic mineral products and changes in the use of many of those already well known. Among these is diatomite, formerly employed as a mild abrasive and, at one time, as the absorbent material in dynamite. Now nearly 100,000 tons a year are mined and milled into such things as filter aids, cement admixtures, insulants, fillers, absorbents, cosmetics, cleansers, etc. Pumice, commonly regarded as only an abrasive, is now also employed as an insulant, as light-weight aggregate and as a concrete admixture. With increasing use of insulants, light-weight aggregates, and acoustic stuccos and plasters in the building trades, both these mate-rials should find increased application. Very large deposits occur in eastern Oregon and have been studied by the U. S. Geological Survey in cooperation with the Oregon State Mining Board.

Jan 1, 1934

By G. C. Rauch, T. H. Courtney, J. Wulff

The superconducting behavior of Nb-Ti alloys containing 40 and higher wt pct of Nb and variable oxygen content was studied as a function of thermomechanical processing. Critical current density (Jc) us applied transverse magnetic field (H) data were obtained for 0.010 in. diam wires at 4.2° Kin steady fields up to 120 kOe. The precipitate responsible for increase in Jc in each of the alloys studied was related to niobium and oxygen content. In alloys containing 40 to 60 wt pct Nb with less than about 1600 ppm of oxygen, w precipitation in the range 350° to 450°C appears to be responsible for the maximum value of Jc observed. In alloys of higher oxygen content (-2500 ppm), the oxygen-enriched a phase which precipitates in the temperature range 450° to 550°C is a more effective fluxoid pinner. Maximum Jc in low oxygen (350 ppm) 80 wt pct Nb alloys was achieved by 600°C aging heat treatments. Measurements of resistive critical field also reflect the changes in composition accompanying precipitation in these alloys. It is well known that the superconducting critical current density, Jc, of solid solution superconducting alloys can be increased by precipitation heat treatments.1-4 The precipitate, to serve as an effective superconzlucting fluxoid pinner and increase Jc, must be of proper size and spacing.' Its electronic properties must also be different from those of the matrix.6 As in age-hardenable systems, optimum temperature and time of aging are dictated by the composition and history of the particular solid-solution alloy under consideration. The alloy diagram of Ti-Nb7-9 shown in Fig. 1 is typical of ß-stabilized Ti alloys. Precipitation to achieve high Jc in Ti-Nb and Ti-Ta alloys is usually carried out in what is believed to be a two-phase a + ß region.1,2,4,10 Previous work on Ti-Nb4,11 and on other ß-stabilized systems such as Ti-V, Ti-Mo,12-14 has shown, however, that the first precipitate to appear is not necessarily (Y. Under specific conditions the meta-stable w phase is precipitated instead. A further complication arises in such alloys from the strong influence of contained oxygen on the phase stability and on the kinetics of precipitation.15,16 The superconducting critical current density of Nb-Ti alloy containing less than 36 wt pct Nb has been studied by Vetrano and Boom1 and Kramer and Rhodes.4 The most effective aging temperature was found to be about 425°C; fluxoid pinning was attributed to the precipita- tion of a by Vetrano and Boom and of w by Kramer and Rhodes. Although the latter workers used recrystal-lized material and the former cold-worked, studies carried out in our laboratory lead us to believe that the type of precipitate responsible for increased Jc is unaffected by prior cold-work.17 That other types of precipitates may also be effective, especially in higher oxygen-containing alloys, has been demonstrated by Reuter, et al.2 in this laboratory with the aid of electron microscopy. Reuter et al. found that at an aging temperature of 600°C, fee-TiO is precipitated, resulting in high values of Jc. Even higher values of Jc were observed after heat treatment at 500°C, but the precipitate could not be indexed as fee-TiO. Whether the precipitate was oxygen-rich w or a could not be clearly distinguished. The work nevertheless indicates that appreciable amounts of oxygen alter the nature of the phases precipitated at different temperatures, at least in alloys containing more than 36 wt pct Nb. Since such compositions are more readily worked into suitable wire than lesser niobium content alloys, it was decided to study the response to aging of the alloy compositions reported in the present paper with the hope of clarifying the effect of composition on the precipitation processes responsible for high values of Jc. I. EXPERIMENTAL Nb-Ti alloys containing 40, 50, 60, and 80 wt pct Nb were prepared by are-melting 35 g ingots of iodide crystal bar titanium and electron-beam melted niobium.

Jan 1, 1969

By E. T. Hayes, A. H. Roberson, M. H. Davies

R. F. Dornagala and D. J. McPherson (Armour Research Foundation, Chicago)—I should like to compliment the authors for a workmanlike job in determining the partial phase diagram of a system comprised of two rnetals which are certainly not easy to work with. We are completing work at Armour Research Foundation on an Atomic Energy Commission-sponsored project for the determination of eight zirconium binary diagrams. Work on the Zr-Cr system has been completed and should be published within the next year. For our work, Westinghouse Grade 3 iodide crystal bar served as the zirconium melting stock. Johnson-Matthey, electrolytic chromium, specially treated for oxygen removal, was employed. The overall constitution of the system determined at Armour Research Foundation is in very good agreement with the present work. We found a eutectic at 18 pct Cr and 1280 °C, somewhat lower than the value reported. This temperature was confirmed by thermal analysis, incipient melting studies, and regular isothermal anneals. The eutectoid was located close to 1 pct Cr and 835°C by metallographic analysis of annealed specimens. Maximum solubility of chromium in /S zirconium was 4.5 pct at the eutectic temperature. Chromium solubility in a zirconium was less than 0.28 pct at all temperatures. We found the compound at 53 pct to melt around 1700°C, with an open maximum, but determined its crystal structure to be hexagonal close-packed (MgZn, type). The lattice parameters were in excellent agreement with those determined by Wallbaum in 1942. The diagrams are in substantial agreement, and .part of the differences are undoubtedly due to the use of different zirconium melting stock. M. K. McQuillan (Birmingham, England)—I read this paper with a great deal of interest, as it covered the same field as some work of my own.' There are a number of points in the present paper on which I would like to comment. First, I should say that I, too, used zirconium prepared by magnesium reduction of the tetrachloride and electrolytically prepared chromium, and melted the alloys in a Kroll-type arc furnace. The purity of my alloys should, therefore, be comparable with the purity of those of the present authors, and any differences in our observations would not be expected to be attributable to this cause. The differences between my observations and theirs concern the presence of the eutectic, the temperature of the eutectoid, and the melting point of the compound. I would be very much interested in any further evidence the authors may have for the occurrence of the eutectic at 1380°C. During the course of my work I noted that a number of my alloys containing 60 to 90 pct Zr melted at about 1400 °C, and for a time assumed that a eutectic occurred at this temperature as described in the paper. On further investigation, however, I found that the structures of the as-melted alloys could not be made to fit in with this interpretation of the system. If a eutectic exists in this region of the system it would be expected that the as-melted alloys would show the usual type of cast structure, i.e., dendrites of the compound plus eutectic. This, however, does not occur, as may be seen from Fig. 9. The compound seen there is not dendritic in form, and the remaining material is by no means certainly eutectic. It may be argued that a compound such as ZrCrl would not form dendrites but would tend to crystallize in geometric shapes. In this case, however, I have evidence to the contrary, as on the chromium side of the compound, where a eutectic occurs at about 1545"C, the compound formed from the liquid takes on a conventional dendritic form, and the eutectic is observed in the interdendritic spaces in the usual way. There is no reason to suppose that the compound would behave differently in an alloy lying on the zirconium side of the compound composition if a eutectic existed there too.

Jan 1, 1953

By O. R. Wagner, R. O. Leach, H. W. Wood, C. F. Harpke

PAN AMERICAN PETROLEUM CORP.TULSA, OKLA. CASPER, WYO A field test has been made in which additional oil recovery was obtained from a previously-waterflooded "oil-wet" sandstone reservoir. This recovery improvement was accomplished by adjusting the reservoir wettability through chemical treatment of the flood water. The test was made in the Muddy sand of the West Harrisburg Unit, Neb. The chemical used, sodium hydroxide, was injected as a slug of dilute caustic solution through a water-injection well. The natural wettability of the reservoir and the chemical requirements for reversing wettability were determined in the laboratory from contact-angle studies using field water and oil samples. Laboratory flood tests with a synthetic system had shown that reversing the wettability of an oil-wet consolidated core would lead to improved oil recovery. The field performance indicates that the mechanism by which increased oil retovery is obtained in the field is the same as that observed in the lahoratory. Laboratory studies indicate that higher ultimate recoveries and decreascd water-injection requirements result when the adjusting agent is added early in the life of the flood. However, a previously waterflooded area was intentiorzally chosen for the field test so that unambiguous conclusions could be made about the effects of chemical injection on wettability and the extent of oil-recovery improvernent afforded by wettability reversal. Forces existing at the fluid-solid and fluid-fluid interfaces in a porous medium have an important effect on oil recovery during a water flood. Modifying these interfacial forces in the reservoir to improve oil recovery has been the object of much research. Several papers' ' have discussed the use of surfactants to lower the water-oil interfacial tension. This paper describes work concerned with improving oil recovery by modifying the forces at the fluid-solid interfaces— that is, by changing the preferential wettability. An earlier paper: presented evidence to show that some reservoir systems could be changed from preferentially oil-wet to preferentially water-wet by the action of simple chemicals added to the water to increase waterflood oil recovery. The process was attractive for further study because it used only inexpensive chemicals and because it called for a gross "wettability reversal" rather than for a precise adjustment. The present paper is an extension of the earlier work. Laboratory flow tests were made using treated water and oil in a consolidated core to determine the amount of additional oil recovery and the producing performance which might be expected from reversing the wettability of an oil-wet reservoir during a flood. A contact-anglc study using water and oil from the Muddy "J" sand of the Harrisburg field, Banner County, Neb., indicated the reservoir to be preferentially oil-wet and susceptible to wettability reversal through chemical injection. Based on these studies, a field trial of wettability-reversal water flooding was initiated. in the Harrisburg field. The primary purpose of the trial was to determine if wettability-reversal flooding would improve oil recovery in an actual field situation. The field trial was also an important test of the laboratory tecnique used to determine the effect on oil recovery of certain wettability manipulation, as well as a test of the contract-angle method of determining reservoir wetra-bility. The paper is presented in two parts. The first part covers the laboratory experiments leading up to the field trial, and the second part covers the field trial. PART I—LABORATORY STUDY The laboratory experiments consisted of displacement tests using an idealized fluid system and of a contact-angle study with crude and water from the Muddy "J" sand of the West Harrisburg Unit, Banner County, Neb. The displacement tests were designed to determine the effects of a particular wettability manipulation, oil-wet to water-wet, on oil displacement in a water flood. The contact-angle measurements were made to determine the natural wettability of the reservoir and to determine if beneficial wetting changes could be brought about by a chemical addition to the flood water. PROCEDURE DISPLACEMENT TESTS The displacement tests were perfornled in a consolidated sandstone core using a refined oil and water. The wetting properties of this system could

By E. J. KENNEDY

THE 142D MEETING of the Institute is rapidly shaping up with splendid prospects of a strong technical program and the lighter side of this annual occasion amply provided for. The date is February 20 to 23. The technical sessions will be held in the Engineering Societies building; the smoker-dinner, the informal dance, and the annual reception and dinner, at the Commodore Hotel, Monday, Tuesday and Wednesday respectively. The news to date on the technical side is as follows: Mining Methods-Subsidence The Mining Methods Committee has prepared an interesting program which will be divided into two sessions to be held early in the week. At the first there will be papers on mining methods and development, including a description of the "Sinking and Equipment of No. 2 Shaft at Minas de Matahambre," by Dudley D. Homer and R. H. Cromwell. They describe in considerable detail the equipment used and the practice followed in sinking this important shaft, giving detailed costs and performance figures. Hoist¬ing ?arrangements and mining practice at the "Red Ore Mines of the Woodward Iron Co. at Bessemer, Ala.," are described by Tenny C. DeSollar, superintendent of mines, in a second paper. At this session of the Mining Methods Committee, H. M. Roche and R. E. Crockett, of the Committee on Eastern Magnetite Mining and Milling Methods, will present their paper, "Iron Ore Mining at the Scrub Oak Mine." This mine is in the highlands of New Jersey about 40 miles west of New York City. Prof. Robert K. Warner of Yale University will present a paper on "The Selection of a Mining System," which should have an interesting discussion. Pierre R. Hines, of Portland, Ore., will present, with stereopticon slides, his paper on "The Owyhee Tunnels, U. S. Reclamation Project, Owyhee, Oregon," describing one of the recent irrigation undertakings.

Jan 1, 1933

By Herbert A. Wendel

Reaching the miner with safety education" is R the ultimate goal, the main objective, of every safety program in the mining industry. If we can get safety education to every worker, and it is properly learned, enforced and obeyed, we should eliminate at least 85% of all potential accidents. We should then have very few accidents as a result of unsafe behavior, which, in turn, would allow us to concentrate most of our future efforts on preventing the types of accidents which are caused by faulty or defective machinery, equipment, tools and materials. An uninformed or uninitiated person would think that it should be a rather simple process to reach the miner with a safety education. Theoretically he would be right because here we get involved in a matter of semantics. When we say "reaching the miner with safety education" we actually mean that this education must also be accepted and learned by the miner; we intend to mean that safety must be observed and followed at all times. But in order to realize our complete meaning of the phrase, we must find the solution for a number of problems and obstacles which are well known to management and safety personnel.

Jan 1, 1965

By F. Forward, H. Veltman, A. Vizsolyi

Activities of oxides in the ternary FeO-MnO-SiO system are calculated from data on the binaries, using the Gibbs -Schuhmann method. These activity data are used, together with thermodynamic relations, to calculate the contents of oxygen, silicon, and manganese in liquid iron, and the composition of the corresponding oxide phases in equilibrium with it. Excellent agreement was found between calculated and experimental metal compositions, indicating that thermodynamic methods, such as those presented, can supply useful data on slag-metal equilibria, and are therefore capable of wider application. When molten steel containing oxygen is treated with a deoxidizer, the product of the reaction is composed of the oxides of the deoxidizing elements together with more or less iron oxide. This assemblage of oxides is presumably very close to equilibrium with the melt since it is formed directly from elements dissolved in it. Therefore, it is likely that metal analyses corresponding to a given oxide phase composition are calculable with considerable precision where sufficient information is available on activities in both phases. The present study was made to test this hypothesis in the case of deoxidation by silicon and manganese. Here experimental data on the relationship among oxygen, silicon, and manganese in the metal phase are available, as are activity data for the MnO-SiO2, FeO-SiO2, and FeO-MnO binary systems. A further objective was to demonstrate in a specific example how gaps in the data may be filled by judicious interpolation, and how the Gibbs-Schuhmann method is applied to obtain activities in ternary systems. The rigorous derivation of the latter, requiring considerable facility in handling partial differential equations, tends to mask the real simplicity of the method, and repel the very engineers and experimenters who would benefit the most from its use. I) GENERAL PROCEDURE Deoxidation of steel with silicon and manganese results in the formation of two phases, metal and oxide. The number of components is four—Fe, Mn, Si, and 0. The phase rule then gives the number of degrees of freedom: If temperature and pressure are fixed, 2 deg of freedom remain. Consequently, it suffices to fix the concentration of two of the components of the system for all the concentrations to be determined and, at least in principle, calculable. The practical problem is then to discover a straightforward method of calculation with a minimum of trial and error solutions. The type of reactions to be dealt with are like the following: Si (in steel) + 2 O(in steel) = SiO2(in oxide phase) The standard free energy of this reaction is readily obtained from the literature, so that the equilibrium constant can be calculated by the expression: Since the metallurgist is concerned with percentages rather than activities, a real solution requires information that will permit activities to be converted to concentrations. This information is fairly adequate for the elements dissolved in molten steel, but is not available for the FeO-MnO-SiO2 oxide system. Therefore, the first step in this study was to find the relation between activity and concentration for the three oxides making up the system. The next step was the calculation of slag and metal compositions that are in equilibrium with one another. As shown by the phase rule, it is sufficient to assume the values of two composition variables in order to calculate the rest. But which two are picked makes a vast difference in how difficult the calculation turns out to be, so that it is necessary to make preliminary trial of several routes to find the easiest one. A convenient method is to begin with the slag, and to pick FeO concentration and that of one of the other oxides. Starting with the relation between oxygen dissolved in the liquid steel and FeO in the slag permits a good first estimate to be made of the oxygen content of the steel in equilibrium with FeO, because the iron content being fairly close to 100 pct, Fe has an activity close to unity. Using this first estimate of oxygen activity, approximate values of the manganese and silicon contents of the melt are readily calculated from the appropriate equilibrium constants. A minor correction for the depar-

Jan 1, 1963

By Eugene N. Cameron

Graphite is the hexagonal form of crystal-line carbon. It is found in nature locally as tabular crystals but occurs mostly as disseminated flakes, foliated, platy, or fibrous masses, or microcrystalline compact to earthy material. Graphite is characterized by its gray to black color, metallic luster, black streak, perfect basal cleavage, softness (H = 1-2) and unctuous feel. It is sectile and flexible and has a specific gravity of 2.1 to 2.3. It is an excellent conductor of heat and electricity and is inert to ordinary chemical reagents. It melts at a temperature of about 3500°C and vaporizes at a temperature of about 4500°C. In the presence of oxygen it oxidizes to CO2 in the temperature range 600° to 700°C, but it is stable at ordinary temperature and markedly resistant to chemical weathering. Although some natural graphite is nearly 100 pct pure carbon, most contains mechanical impurities of various kinds; quartz, biotite, muscovite, pyrite, iron oxides, and feldspars are the most common. Commercial graphite products have a wide range of graphite content, but the better grades contain 80 pct graphite or more. Both natural and manufactured (artificial) graphite are used in industry. Natural graphite products are divided into two broad categories based on grain size. Graphite composed of visible crystals is called "crystalline" graphite, whereas graphite so fine-grained that it is not visibly crystalline is termed "amorphous." The distinction is arbitrary, for all natural graphite is crystalline, and all gradations between the two commercial categories are known. Within the two categories the terminology used in industry is confusing and not entirely consistent. Crystalline graphite comes from two principal types of sources. The first consists of rocks containing disseminated flakes of graphite. This source yields the "flake graphite" of industry. The second comprises vein deposits of graphite, of which those in Ceylon are the most important and furnish the Ceylon graphite of industry. Amorphous graphite comes from any of a variety of sources, including some of those that yield crystalline graphite. Manufactured graphite is made by electric furnace processes, mostly from petroleum coke. Occurrence and Distribution of Graphite Deposits GENERAL Graphite is widely distributed in nature, occurring in igneous, sedimentary, and metamorphic rocks, and even in nickel-iron meteorites. Graphite deposits of economic interest, however, occur mostly in metamorphic terranes. Five principal geologic types of deposits are recognized: 1. Deposits consisting of flake graphite disseminated in metamorphosed siliceous sediments. 2. Deposits consisting of flake graphite disseminated in marbles. 3. Deposits formed by thermal or dynamothermal metamorphism of coal or other highly carbonaceous sediments. 4. Vein deposits of the Ceylon type. 5. Contact metasomatic or hydrothermal deposits in marble. DEPOSITS IN METAMORPHOSED SILICEOUS SEDIMENTS Deposits consisting of flake graphite disseminated in metamorphosed siliceous sedi-

Jan 1, 1960

By S. R. Goodman, Hsun Hu

The rolling texture transition in copper as a function of deformation temperature is found to be quite similar to that in high-purity silver. The ordinary copper type texture changes gradually to the brass type, accompanied by an increase in the stacking fault frequency, as the temperature of deformation decreases. The rolling textures obtained at low temperatures and the corresponding annealing textures compare remarkably well with the ordinary rolling and annealing textures of low-zinc brasses. Furthermore, it is also found that the observed stacking fault energies of copper specimens deformed at low temperatures correspond closely with those of low-zinc brasses, as deduced from measurements of the dislocation nodes. These results are consistent with the idea that texture transition may be significantly dependent on the stacking fault energy. It was shown in a series of previous publications1"3 that the rolling texture of high-purity silver changes gradually from the common silver type (or the brass type) to the copper type* with increasing temperature *The silver or brass type rolling textures are commonly described as (110)[112],4,5 whereas the copper type rolling textures are mainly (123) [a121 and (146)[211].5 Other ideal orientations have been used by various investigators for the copper type rolling textures, but the actual difference among these ideal orientations is rather small. of deformation, and that such texture transition can be correlated with the change in stacking fault frequency as a function of rolling temperature. Furthermore, it was shown that the formation of annealing textures in high-purity silver from the various rolling textures obtained during the course of texture transition depends entirely upon the deformation texture. From a common silver type or brass type rolling texture (such as produced by rolling at 0" or at 50° C) the recrystallization texture is mainly (120)[211], which is quite different from the recrystallization texture of brass.* However, for both ma- terials the orientation relationship between the rolling texture and the recrystallization texture can be expressed in terms of similar rotations around [Ill.] axes of approximately 30 or 35 deg. They differ in that the [Ill] rotational axes are different. In the case of high-purity silver, the axes of rotation are the two (111) poles near the plane normal of the deformed specimen with a (11l)[112] type rolling texture, whereas in brass, they are the (111) poles near the direction of rolling. For high-purity silver with a predominantly copper type rolling texture (such as produced by rolling at 150° or 200°C) the recrystallization texture is mainly (100)[001], or the cube texture, plus its twin orientations. It was shown previously6 that such reorientation observed in copper or aluminum can be described as [Ill] rotations of 30 to 40 deg. For intermediate cases, i.e., when the rolling textures are composed of a

Jan 1, 1963

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Cartersville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.1 With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2

Jan 1, 1949

UNIVERSITY OF ALABAMA University, Ala Mining and Metalliaigical Society* G L Roberts, President T G Patterson, Vice-President B B Copeland, Treasurer K F Stark, Secretary G T Bator, Faculty Sponsor F H Crockard, Counselor

Jan 1, 1949