Search Documents

By George B. Harrington

This paper is a brief description of the design and equipment of a new coal mine in southern Illinois, which has many features not common practice in shaft coal mining and which is laid out and equipped for such unusually large capacity that it promises soon to become one of the largest mining operations of its kind. Shaft sinking for the mine, New Orient, was commenced in May, 1921, by the Chicago, Wilmington & Franklin Coal Co. In October, 1924, the plant was practically completed and was producing over 6000 tons of coal per day. There is good prospect that within a few years, when the mine is fully developed and manned, the output will attain a daily rate of 12,000 tons. The coal seam at New Orient lies approximately horizontal, about 500 ft. below the surface, and may be said to run from 9 to 12 ft. in thickness. The tendency in Franklin County has been toward large mining units (5000 to 6000 tons per day) with great care being given to protection against fire and explosion hazards, and usually with quite elaborate surface plants permitting careful preparation of the coal into graded sizes comparable with those made in the anthracite region. The field is unionized, with uniform conditions of wages for various classes of work, hours, etc., and the Illinois mining laws are quite specific with regard to fireproofing and safety measures. These conditions make it difficult for any hut well-equipped and well-operated mines to meet the competition of the numerous fine properties of which this county can justly be proud. The coal company's property was already developed on the western side by the Orient mine—a much visited and written about operation (with which many of you are possibly familiar through the Department of Mines' film "The Story of Coal") which until recently held the 8-hr, production record with 8218 tons and usually ran quite consistently with production of slightly over 6000 tons per day. Experience at Orient wat naturally one of the greatest influences in determining the location and character of the New Orient.

Jan 1, 1925

MEETING OF SAN FRANCISCO SECTION Twenty members were present at the meeting of the San Francisco Section, May 20, 1919. Chairman Bradley being in Alaska, vice-chairman, T. A. Rickard, presided. Prof. Frank H. Probert gave a short account of the activities of the governmental commission, consisting of himself, George S. Rice, and F. G. Cottrell, which recently visited Europe, and studied the coal, iron, salt, and chemical industries. When the work is finished reports will he issued. He gave a resume of the history of. the changes in nationality of Alsace-Lorraine and 'described the importance of the region for coal, iron, and potash. With the return of these provinces France will have an annual output of more iron ore than she has coke to smelt it with; hence, the importance of the Saar coal field. With these new mines France will take the predominant position in the iron and steel-industry formerly held by Germany. Many details were given of the devastated mines of France, and of their former value, production and the destruction that overtook them. Noteworthy is it that much of the damage was done as late as Oct. 28, 1918, for the express purpose of ruining the country industrially. The damaged area of the Valenciennes coal basin embraced twenty-four concessions, three were damaged by artillery bombardment, but have resumed operations since the' armistice, nine had their surface: equipment destroyed by battle, pillage, and sabotage, while twelve concessions at the eastern-end of-the field suffered from wilful, systematic destruction. Of the 285 shafts in the district, 172 were flooded either by: turning surface streams into them, or, by wrecking the cuvellage; thus, admitting water and quicksand from the water-bearing strata above the coal measures. Two hundred and thirty-five surface plants were damaged, many of them to such an extent that they must be scrapped. These properties gave employment to 135,000 men before the war and, even admitting the remote possibility of getting workmen, the terrible destruction and devastation makes housing and living a difficult problem. It will probably be from 3 to 5 years before the mines are drained and information obtained as to underground conditions; to attain the pre-war output may require from 12 to 15 years.

Jan 8, 1919

By M. C. Fuerstenau, R. B. Bhappu

The response of beryl to sulfonate flotation was examined. The dependence of flotation recovery on sulfonate concentration, pH, and the absence or presence of various ions is also demonstrated. The response of quartz and feldspar to sulfonate flotation at various values of pH is given to. show the conditions necessary for selective separation. Finally, beryl was successfully concentrated from a natural ore using a technique devised from experimental observations on systems of pure minerals. With the possible exception of quartz, the flotation characteristics of silicate minerals are rather poorly understood. This is due in part to the com- plexity of the mineral systems themselves and in part to an insufficient amount of flotation data. The complexity of the systems arises from the wide range of chemical composition that the silicate minerals can assume. This is reflected in the variability of such physical properties as hardness and cleavage. Although the chemical composition of silicate minerals can vary considerably, a general grouping can be accomplished conveniently on the basis of the assemblage of SiO4 tetrahedra in all the silicates. That is, it has been shown that six basic groups can be obtained, depending on the arrangement of oxygen sharing between adjacent silicon atoms (or substituted aluminum). When all four oxygen atoms are shared, a framework structure such as quartz or feldspar is obtained. When three oxygens are shared, infinite sheets are obtained as in the micas and clays. When two oxygen atoms of the tetrahedra are shared, infinite chains are obtained, such as those in

Jan 1, 1963

By S. R. Mitchell, M. C. Fuerstenau, A. M. Gaudin

The two principal attributes of a thickener pulp are its settling rate and the ultimate pulp density of the thickened mud. Testing for evaluation of thickening attributes of a pulp has usually been done batch-wise by placing the pulp in a one-liter glass graduated cylinder and noting the position of the boundary between clear liquor and mud as a function of time. Refinements in testing have included repulping a thickened mud to various dilutions and evaluating the settling rate on these various repulped muds. This is considered to make possible an estimate of the settling rate as a function of pulp density and therefore to pinpoint the slowest settling pulp which ought to be critical from the standpoint of thickener plant design. Finally, tests are sometimes made with model-size continuous thickeners of arbitrary size. In batch tests it is generally accepted that the behavior of a pulp is described by a curve such as the one shown in Fig. 1, in which the position of the boundary between clear liquor and mud (the mudline) is plotted against time. It has also been assumed that the initial settling rate (the slope of the line segment AB) is descriptive of the pulp and independent of the size and shape of the container. Where the settling rate is slower and clearly a function of time (portion CD of the settling curve), it has been assumed that the data are not of much use because of the intrusion of compacting phenomena. The next important datum is the height. PE, which is a measure of the so-called ultimate pulp density. This quantity is assumed to be characteristic of the pulp and independent of the container. When actual data are recorded, results are rarely exactly according to this theory and numerous deviations may be noted. For example, some pulps seem to require an appreciable delay before beginning to settle, as in line AF. This is spoken of as representing the need for an induction time for flocculation. It has seemed desirable to explore thickener data with a more sensitive charting tool than is afforded by the coordinates of Fig. 1. Instead of relating the position of the mudline to time, it has seemed desirable to relate the rate of descent of the mudline to time. This, in effect, amounts to charting the slope of the line in Fig. 1, or the derivative of its ordinates, against the same abscissas. Fig. 2 shows the new chart for the curve ABCDE of Fig. 1. When this new tool was applied to data obtained, for example, with sized clay pulps, astonishing differences appeared. Apparently the traditional tool conceals differences instead of revealing them, whereas the new method emphasizes them. It seems, also, that both charting methods have their uses. In this article attention is focused on the effects of pulp density and container height as they affect the settling behavior of flocculated suspensions of a sized kaolin. The thesis by M. C. Fuerstenau' gives more details than this summary, as well as some information about the effect of other variables. Sized fractions of kaolin were used, supplied through the courtesy of S. C. Lyons of the Georgia Kaolin Co. Large batches were made by agitation in a flotation machine and in a glass jar equipped with a mixer. The settling vessels were 2, 4, and 6-in. diam glass cylinders of various heights. Pulp Dilution: The effects of pulp dilution on sedimentation behavior are shown in Figs. 3, 4, and 5. Fig. 3 shows data on pulps ranging from 2.44 to 16.7 pct solids initial pulp density, flocculated with Separan and charted in the traditional manner. At least two of the lines appear nearly straight in their early sections, but neither of the others does. Each of the curves in this figure includes a region labeled

Jan 1, 1960

The eastern part of the state of Rhode Island on both sides of Narragansett Bay, including the island of Rhode Island, is underlaid with carboniferous rocks which carry veins of anthracite. This formation extends into the neighboring portion of Massachusetts, including the area from the state line, the towns of Mansfield, Brockton and Bridgewater,: and extending probably ten miles east of the latter two towns, to Middlesboro, and to Fall River. In Massachusetts the coal formation extends over nearly the whole of Bristol, and parts of Plymouth and Norfolk Counties. In Rhode Island and Massachusetts the area covered is about 400 square miles. In both states the exact limits of the coal measures cannot be determined on account of a thick layer of drift which overlays it. Along parts of Narragansett Bay, the coal measures outcrop in the cliffs on the west side of Rhode Island, and the presence of coal here seems to have been noted as early as 1760, and in 1768 a patent was granted to parties who "were about to dig after pit, coal or sea coal" at the back of the town of Providence. In 1807-08 Benjamin Silliman, later a geologist, visited some openings,' and in 1808 a mine was opened near Portsmouth, in the northeast part of Rhode Island. Work was done here until about 1814 when the mine was abandoned. No anthracite had been used in New England at that time, all coal used came from Nova Scotia, Virginia or England, and was high volatile bituminous; neither experience nor the means of firing favored the use of the local fuel? This mine was again working in 1827, was again abandoned and operations were resumed in 1847. In 1837 a note in a magazine mentions, "the immense coal mine in Cumberland-about six miles from the city of Providence" as having a shaft 14 ft. in diameter and 80 ft. deep, that the horses then used for hoisting the coal were to be superseded by a steam engine and another shaft was to be sunk. With these improvements 30,000 to 50,000 tons were to be produced the following year at a cost of $1 per ton and a sales realization of $6.1 Hitchcock's report refers to a number of localities in both states where definite knowledge of coal existed. These are:

Jan 1, 1942

By Arthur F. Wendt

The hot-blast oven of which the accompanying plate gives complete details, was designed by the writer for the spiegel-furnace of the Lehigh Zinc and Iron Co., at Bethlehem, Pa. Members of the Institute who visit these works will have occasion to notice the large amount of zinc-dust in the gases, and the consequent dirtiness of both the hot-blast and the boilers. The zinc collects in a crust on the iron hot-blast pipes and leads to the frequent burning of them. A large vertical standing-pipe stove, a modification of the "Pleyer," thus gave considerable trouble by the burning of pipes and, on one occasion, the toppling over of a whole row. These inconveniences are avoided in the hanging-pipe stove under consideration, and less heating-surface has been found to be required to heat the blast to a given temperature. The construction of the stove is so simple and so plainly shown in the plate that it is needless to enlarge upon it. Each pipe rests in a box and is connected by U-branches with the next adjoining pipes. An iron sleeve is placed around the joint and tightened, as usual, with iron filings. In case of a pipe burning out, that particular section is cut off by the valves and the sleeves are broken. The pipe is then readily lifted out of the box and a new one is substituted. The whole operation requires only a short time and the section can then be at once put into use. The boxes supporting the pipes cover the whole surface of the hot-blast and are closed by iron covers rammed with fire-clay. Owing to the air-space around the U-pipes there is little loss of heat in the upper part of the stove. Each section as built has 280 square feet of heating-surface. The furnace is blown by a horizontal engine with 46-inch stroke and 48-inch diameter of blowing-tube. At 28 to 30 revolutions, the engine delivers 3000 cubic feet of air per minute, at a pressure of 5 pounds. When five sections of stove are in use, the blast enters the furnace at a temperature of 850" F. That is, there are over two cubic feet of air per square foot of heating-surface heated to that temperature per minute.

Jan 1, 1887

MRS. SIDNEY J. JENNINGS, President, MRS. ARTHUR S.. DWIGHT, First Vice-President, MRS. KARL EILERS, Second Vice-President, MRS. H. W. HARDINGE, Third Vice-President, MRS. BRADLEY STOUGHTON, Recording Secretary, MRS. AXEL 0. IHLSENG, Corresponding Secretary, MRS. ARTHUR S. DWIGHT, Acting Treasurer. Welfare Committee MRS. C. C. BURGER, Chairman, Sub-Committees Americanization Belgian Relief MRS. LEVI HOLBROOK, Chairman, MRS. HENRY H: KNOX, Chairman, Emergency MRS. HERMAN A. PROSSER, Chairman. Since the annual meeting held in February, 1917, when the Woman's Auxiliary to the A. I. M. E., was formed, the work of organization, which of necessity must be slow, has steadily gone forward. Under the Chairmanship of Mrs. C. C. Burger of the Welfare Committee, three active sub-committees have been formed: that of Americanization; under Mrs. Levi Holbrook, who is eminently fitted for such a position, by her active and valuable work in a number of the fine patriotic societies of our country; the Belgian Relief Committee, under Mrs. Henry H. Knox, which has clone phenomenal work in the three months of its existence, and whose report is later given in detail; and the Emergency Committee under Mrs. Herman A. Prosser, which has a fund already established, and is. in close touch with Major Arthur S. Dwight, ready to act when necessity arises. The officers of the Auxiliary feel more than gratified at the response so far received, and in a later issue will print extracts from letters, if permission can be gotten from the writers, showing the interest and enthusiasm that have beer aroused by the formation of a Woman's Auxiliary. Answers have even come from far Korea "the hermit nation," from Australia, from South America, showing what a bond of sympathy and, helpfulness is in process of growth. It is our sad duty to announce the death of our Treasurer, Mrs. George D. Baryon, who, from the very inception of our plan to organize, was an inspiring and valuable co-worker. Her place will be difficult to fill. Mrs. Arthur S. Dwight is Acting Treasurer at present. The Auxiliary wishes to express its heartiest thanks to Mr. Stoughton, the genial and efficient Secretary of the A. I. M. E., for his cooperation and valuable suggestions in the difficult work of organizing. He has indeed been "a guide, philosopher and friend." SUSANNE M. IHLSENG (MRS. AXEL 0.), Corresponding Secretary.

Jan 7, 1917

By M. von Heimendahl, G. Thomas

The microstructure of TD-Ni has been examined by transmission electron microscopy in the extruded, annealed. and deformed states. The tensile properties hove been correlated with the observed microstructures and the results ore com-pared with those obtained from pure nickel. The important conclusions are that the thorin particles in TD-Ni act as strong burriers to dislocntion motion during both deformation (slip) and annealing (climb). During deformation. the dislocations tangle around the particles and a cell structure is devleloped after 10 pct or more strain. The cell size appears to be determined by the spacing of the largest particles and is about five times smaller than that in pure nickel for the same strain. The higher work-hardening rate in TD-Ni compared to nickel is probably due to the more rapid rate of dislocation multiplication in the alloy as a result of dislocation-particle interactions. The Th0,particles inhibit recrystallization and twin growh so that some strengthening may arise from the high density of small annealing twins. THE strengthening of materials due to the presence of a dispersed second phase has been the subject of considerable experimental and theoretical investigation in recent years. One of the newest dispersion-strengthened alloys to be developed is TD-Ni,1 a system of approximately 2 vol pct thoria (ThO2) dispersed in a matrix of commercially pure nickel. This material is fabricated by powder-metallurgical techniques and offers high-temperature stability and useful mechanical properties virtually to the melting point of the base metal. While the mechanical properties of this system have been investigated,2,3 there have been no reports in the literature concerning the microstruc-ture of TD-Ni and its correlation to mechanical properties. This paper describes a transmission electron microscopy investigation of the micro-structure of TD-Ni together with its mechanical properties. The results are compared with the structure and properties of pure nickel.

Jan 1, 1964

THE translators wish to record their appreciation of the help given by many individuals with whom they have discussed various details of the work. They are particularly indebted to Mrs. Anne Noble McKeachie, who initiated their collaboration; to Miss Cora Adamson, who spent many hours in making an accurate copy of a much-mutilated &st draft of the translation; and to the Yale University Library which gave access to its excellent collection of books on all aspects of the history of the sciences. The reader will share with the translators their obvious indebtedness to Mr. Carl P. Rollins, Mr. James W. Boyden, and the staff of the Printing-Office of the Yale University Press. The publication of this translation by the American Institute of Mining and Metallurgical Engineers has been made possible by a grant from the Seeley W. Mudd Memorial Fund, administered by a committee composed of Harvey S. Mudd, H. DeWitt Smith, and George Otis Smith. The translators are gratified that their work has been judged to fall within the scope of this Fund, which was established for the advancement of the sciences of mining and metallurgy by the encouragement of research and the dissemination of knowledge, and especially for the furtherance of such activities as might benefit the younger members of the profession. While Biringuccio's book would scarcely serve as a dependable text for the young mining student or metallurgist, it can give him a sense of his membership in a long-standing and honorable profession and enable him better to see his own work in true perspective. It is hoped that this English edition of a sixteenth-century Italian work will be read by the practicing metallurgist as well as by those who have already found pleasure in exploring the past of their profession. A man always feels more at home in a foreign country with men of his own craft than in his birthplace with those of different interests: As in space, so in time, and the modem metallurgist who may be unmoved by the literary and artistic Renaissance will quickly appreciate the spirit of that exciting period as he talks shop with Biringuccio on a visit to mine, smelter, forge, and foundry; as he sees in different forms the very furnaces and machines whose operation and response he knows so well; and as he discusses with this engineer of four centuries ago such topics as the best kinds of fuel or refractory for a given operation, and the importance of adequate supplies of power and material.

Jan 1, 1942

By John Fritz

TROUGH it is not a condition of the Award, the fact is that the John Fritz Medal never has been given to an engineer who had not already received one or more similar awards. This "medal for medalists," on the evening of April 20, was presented to Daniel C. Jackling at a special dinner held at the Union League Club in New York. The citation read "For notable industrial achievement in initiating mass production of copper from low-grade ores through the application of engineering principles." The present award recognizes the same accomplishment-the launching and guiding to the port of marvelous success of the Utah Copper Co., first of the so-called "Porphyries"-as did the award of the William Lawrence Saunders Gold Medal by the A.I.M.E. in 1930, and before that the Award of the Gold Medal of the Mining and Metallurgical Society of America in 1926. Following the custom a biography of the Medalist had been published in a small pamphlet as a supplement to the John Fritz Medal Book. T. A. Rickard was the au¬thor of the sketch of Mr. Jackling, an innovation being the placing of a copy of the booklet at the place of each of the diners. The committee in charge of the dinner consisted of two past-presidents: R. E. Tally, of the A.I.M.E., who was chairman; Bancroft Gherardi, of the A.I.E.E.; and Thaddeus Merriman, director of the A. S. C. E., the John Fritz Medal being a joint award of the four societies. Frederick M. Becket, President of the A.I.M.E., as chairman for the occasion, briefly stated the purpose of the dinner. He stressed his satisfaction that the award was symbolic of the cooperative professional activities of the four great national organizations of engineers. He introduced Francis Lee Stuart, past-president of the A.S.C.E. and now chairman of the John Fritz Medal Board of Award. Mr. Stuart outlined the history and purpose of the Medal established in 1902 in memory of John Fritz, of Bethlehem, Pa., one of the great pioneers of America's iron and steel industry, metallurgist, and president of the A.I.M.E. in 1894. Mr. Stuart called the roll of former John Fritz Medalists, three of whom, Ralph Modjeski, J. Waldo Smith, and Ambrose Swasey, were present to do honor to Mr. Jackling. He then introduced George Otis Smith, whose privilege it was to present the Medalist for 1933. Dr. Smith was the senior of the four A.I.M.E. representatives on the Board that last year selected Mr. Jackling for the honor. His speech follows in full.

Jan 1, 1933

By John Henry Harden

IN 1874, with Mr. H. Y. Attrill, of Baltimore, Md., I made an examination of some property at Goderich with reference to sinking for and mining salt. With this end in view we visited all the wells in the neighborhood, but the information sought being of so unreliable a character I advised the putting down of a borehole on the property. This has since been done, the result of which has lately been published by Dr. T. Sterry Hunt in the Toronto Globe. From this there appears to have been passed through six beds of salt of an aggregate thickness of 123 feet. Rock-salt was known to exist, for, by the boring of existing wells, small crystals had been brought to the surface in the dirt, but no attempt had before been made to obtain a reliable sample or to prove the number and thickness of the beds. The question now remaining for discussion is, shall the present method of obtaining the salt be continued, or shall the beds be won by a shaft in a regular mining fashion, by which means the salt may be gotten in a condition almost ready for the market? The present mode of obtaining salt is by boreholes from 6 inches to 8 inches in diameter drilled to the beds, into which is inserted a pump. The "feeders" of fresh water intersected in drilling the well are allowed to descend on the outside of the pump-tube to the salt beds and there become saturated, when, on use of the pump, brine is obtained for evaporation. In the beginning brine can only be had in limited quantity, but by the daily application of the pump, and the gradual solution of the salt, a larger surface becomes exposed to the action of the fresh water, and a continuous supply of brine is obtained. It will then be understood that the supply of brine is dependent upon the feeders of fresh water intersected in boring the well, which, we are told, have never shown any sign of diminution, and this is the water that must be encountered in sinking a shaft. There are ten wells in operation at Goderich, the most important one to the present project being known as the Hawley Well, located at an elevation a few feet above Lake Huron at the mouth of the river Maitland, at a much lower level and nearer to the proposed shaft than any other well in the district. At this well the feeders

Jan 1, 1877

By A. Rosenzweig, M. M. Karnowsky

The generalized binary diagram of the Au-Sn-Pb system is presented. The chief characteristic is the pseudobinary between lead and AuSn. On the high-gold side of the pseudobinary, four reaction isotherms were found at 363°, 274°, 225°, and 204°C. On the low-gold side of the pseudobinary, three reaction isotherms at 277°, 205°, and 176°C were found. A vertical section from the eutectic solder composition to gold was developed from the isothermal sections generated. METALLURGICAL problems arising from the intentional or accidental formation of Au-Sn-Pb alloys in soldering applications have indicated a need for information on the phase equilibria in this ternary system. The literature indicates that a complete diagram presenting this information has not been prepared. Even the recent excellent work by prince' entitled "The Au-Pb-Sn Ternary System" actually extends only to the AuSn or 50 at. pct Au range. There are more events in the 50 to 100 at. pct Au than in the less than 50 at. pct range. This article by Prince furnished much guidance in preparing this report. Initial efforts with the isopleth from the eutectic solder composition 61.9 wt pct Sn-38.1 wt pct Pb and 0 to 90 wt pct Au indicated that extensions of the work to the whole of the diagram (even if in less detail) were necessary to understand this system. In undertaking the construction of such a diagram, this study used differential thermal analyses (DTA) and metallography with verification and identification of phases by electron microprobe analyses. EXPERIMENTAL PROCEDURE The procedure began with the development of a cell which would be unreactive with lead, tin, and gold, retain its strength to 1100°C, exclude oxygen, and also furnish a suitable well for insertion and protection of a thermocouple to monitor temperature changes in the material. Such a cell would make it possible to reuse the sample should a repetition of determination be desired. Fig. 1 is a photograph of two such quartz cells as finally developed. The specimens have been run many times. The cell is made up of an inner sample bucket and an outer capsule with a thermocouple well which the sample surrounds. The DTA unit was an assembly devised from available instrumentation. The sample holder was a 3-in.-long cylinder of nickel, 2 1/2 in. in diam, fitted securely in a vertical tube furnace. Two holes 7/8 in. in diam were symmetrically located to receive the quartz cells. A dummy cell with nickel powder was used as the reference. The absolute temperature was recorded with a Pt/Pt 10-pct Rh thermocouple with an automatic Kaye ice bath compensator. (Calibration indicated the compensator to be accurate to better than ±0.5° over the 100° to 1000°C range.) The absolute temperature was measured in the sample and recorded on an L&N mul-tirange recorder with a full-scale display of 1 mv and automatic ranging of 99 mv. The differential signal between the sample temperature and the reference temperature was amplified with an L&N microvolt amplifier and recorded on an L&N Speedomax G recorder. Since two charts were obtained, the chart speeds were equalized and each event was noted on the differential chart, and the temperature at that time was obtained from the temperature record.

Jan 1, 1969

SOME days ago a visiting member from Pittsburgh who is an ardent supporter of the Institute remarked: "There are a lot of men who would be members of the Institute if it weren't so expensive. It is not so much the $15 dues as the $20 initiation fee. This makes quite a hurdle, especially for the younger fellows." A little further conversation developed the fact that the member had never learned of the changes in the By-laws regarding initiation fees and dues made by unanimous vote of the Board of Directors last November. As a great many others doubtless are unaware of these changes, the substance of two of the amendments is here repeated. They provide: (1) That the initiation fee for Junior Members (heretofore ten dollars) he abolished. (2) That the age limit for entrance as a Junior Member be increased from 27 years to 33; provided further, that the period during which the dues of a Junior Member are ten dollars shall be a maximum of six years but in no event shall extend beyond his thirty-third birthday. The Junior Member gets the identical privileges enjoyed by his seniors and he likewise assumes the same obligations with the sole exception of the financial payments. This one exception is justified by the fact that the engineers of more mature years, who are established in the profession, - are able and willing to assume a slightly greater financial burden. In effect, it is a small subsidy for the younger men; but these in turn will later enter the group of those that give instead of receive assistance. The practical result is that an engineer under 27 can obtain every privilege and benefit of membership for six years on the payment of only $10 per year without any initiation fee. A man of thirty can do the same for a period of three years. Incidentally, a candidate applying for membership (either as senior or junior) in the next few months need pay dues for the second half of 1935 only. A Junior Member -can be enrolled with an immediate outlay of only $5. The Institute does not seek-members indiscriminately merely to swell the number. These facts are not presented as a "bargain" offer in any sense. The standards for admission are high and are watched zealously. But it frankly-wants to give qualified men who can benefit from membership every encouragement to apply. Naturally, the Institute does not want lack of accurate information regarding initiation fees and -dues to be a stumbling block to any that are eligible and desirous of enrolling. Members are urged to take it upon themselves to clear up misapprehensions on this point, particularly among younger engineers.-Editorial reprinted from MINING AND METALLURGY, May, 1935.

Jan 1, 1935

By H. J. Levinstein, H. J. Guggenheim

RbFeF3 is a transparent ferromagnet with a large faraday rotation which permits the direct observation of magnetic domain structures in bulk crystals. If the position of dislocations within the crystal were known a study of domain wall dislocation interactions would be possible. In this paper an etch pitting solution is described which gives a one-one correspondent between the etch pits and the dislocations intersecting the (100) surfaces of RbFeF3 crystals. In addition, RbFeF3 is shown to have sufficient plasticity so that known arrays of dislocaticms can be put into the crystal. It is concluded that RbFeF, is an ideal material for the investigation of domain wall dislocation interactions. THE influence of lattice defects on the motion of domain walls in ferromagnetic materials has been studied extensively both theoretically and experimentally.4 The experimental data obtained has been qualitative in nature due to the lack either of a quantitative knowledge of the magnetic domain array in the material or of the nature of the dislocation configuration in the material. At room temperature RbFeFJ has the cubic perovskite structure. It is ferromagnetic below 86°K.5,6 It is also transparent and has a large faraday rotation in the magnetic state.7 The domain structure of this material is observable in three dimensions in crystals which are millimeters in thickness.' Since RbFeF3 satisfies the requirements of having an easily visible three-dimensional magnetic domain structure, it was of interest to determine if the dislocation structure of the material could be determined and if the material was sufficiently plastic so that dislocations could be introduced into the as grown crystals. This is a report of the results of that investigation. EXPERIMENTAL PROCEDURE The crystals of RbFeFs used in this experiment were grown by a technique described elsewhere.5 In order to obtain flat strain-free surfaces, the samples were first cut to the crystal orientation desired and the surfaces were polished by employing standard metallographic techniques. The samples were then immersed in a solution of 1 to 3 g of KOH in 100 ml of water. This solution removes the damaged surface layers uniformly leaving a film on the surface of the sample. Etch pits are obtained by immersing the sample in an approximately 50-50 solution of 30 pct peroxide and concentrated acetic acid. The film formed during the KOH treatment turns deep red in color in the etching solution and flakes off the sample. The etching time required depends upon the pit size desired and

Jan 1, 1970

By James E. York

AT a meeting of the American Society for Testing Materials at Atlantic City, June, 1908, Dr.. C. B. Dudley, in his presidential address,' showed the vital necessity of not only making a steel rail as good as in the past, but of making it considerably better in order to meet the present and prospective require¬ments of railroads. Doctor Dudley requested the co-operation of all who from personal experience could give information that would result in bringing about the production of a steel rail that could be relied upon to meet the present requirements. I have had considerable experience in the practical manufacture of steel of almost every grade, during the past 40 years, and I shall suggest changes that will bring about the results desired. Doctor Dudley has had a long experience as chemical and metallurgical expert for the Pennsylvania railroad, but he frankly admits that up to the present time both he and other metallurgical experts lack the practical knowledge of steel-making that is necessary to state correctly the reasons for the unreliability of the steel rails now produced. The necessity is self-evident for more positive practical knowledge on the part of these experts of what is possible and what is impossible regarding the practical manufacturing of steel rails from the ingot to the, finished product. Chemical knowledge in steel-making is far in advance of what it was years ago, and might be said to cover every requirement (in that department) for producing reliable steel. The study of the metallography of steel has been of great value, also the physical testing of steel, but this knowledge will only de-

May 1, 1909

By ROBERT R. ABUOTT

(Cleveland Meeting, October, 1912.) THE practice of carbonizing steel for the purpose of case-hardening has assumed great commercial importance within the past, 10 years. Formerly, case-hardened steel was held in more or less contempt, since it. was considered a cheap substitute for tool-steel. This is no longer the case. The development of the motor-car industry, and coincidentally that of modern alloy-steels, has resulted in overcoming many difficulties formerly experienced in case-hardening. This result has been accomplished by increased knowledge regarding the analysis of the steel which would respond most readily to case-hardening, and by more careful methods of treatment of the carbonized steel. The ordinary method of carbonizing consists in packing the steel with the carbonizing-material in cast-iron boxes and placing them in a furnace at a temperature of from 1,500° to 1,900° F. for a time sufficient to give the required depth of cc case." The steel is then either quenched directly from the box, or is allowed to cool without unpacking, and finally given a single hardening-heat., or, for special work, two or three heats. During the year 1911, more than 100,000 tons of carbonizing-material was sold in the United States, at an average price of probably $55 per ton. More than 85 per cent. of this material consisted of granulated bone. Within the past four years, many manufactured compounds have been placed on the market, consisting largely of some form of carbon or carbonaceous material, with or without the addition of chemicals. Steel will absorb carbon placed in contact with it at the temperature of the atmosphere. The reaction is exceedingly slow, but. increases rapidly with increasing temperature. Below * Metallurgical Engineer, The Peerless Motor Car Co.

Dec 1, 1912

By J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation, sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher. The

Jan 1, 1976

INTRODUCTION Besides the European export credit agencies covered in Ted Rides' paper in this Chapter, other agencies are also active (see Appendix) but the most notable for mining projects are The Export-Import Bank of the United States ("US Exim") and the Export Development Corporation ("EDC") of Canada. Mexico's Fomex is basically a short-term trade-finance fund administered by the Central Bank. US Exim This independent agency can provide loans, guarantees, and insurance. Like all export-credit agencies, its mandate is to support the export of goods and services from the US as a means of competing against other countries' products. If a piece of mining equipment can only he made in the US, the US Exim may very well not provide any financial assistance. (It is important not to place the order for any item for which export credit is sought because, once ordered, the situation is no longer competitive in US Exim's eyes.) Direct Credits and financial guarantees ("buyer credits") are commonly in amounts greater than 85 million and for terms longer than six years. An example here is the $48.5 million provided to PT International Nickel Indonesia (see Robert de Gavre's paper in Chapter 12). US Exim usually requires a 15% downpayment and, therefore, finances up to 857 of the goods; less if the US content is lower. The dollar funding can he US prime, London Interbank Offered Rate (LIBOR), or other sources. Exim can fund in either or both of the following ways: 1. Under a US bank Letter of Credit ("L/C") 2. Reimbursement to the buyer/borrower via a US bank account. US Exim will, without charge, issue a preliminary commitment. It will, however, need to approve the various credit agreements and prefers to tie other parallel financings into one loan agreement. US Exim's total commitments are large, up to $5R billion in aggregate under various programs. US Exim has been the world's leader in medium-to long-term minerals project financings/ co-financings but suffers from (i) aggressive foreign export-credit competition whereby other nations mix in soft-loans or aid programs ("mixed credits") to increase the percentage financed and lower the interest margin and (ii) an imbalance in its own cost of funds. A common US Exim package would be as follows: 15% Banks under US Exim guarantee, floating rate over prime or LIBOR. 35% US Exim funding, fixed rate 35% Pefco funding, fixed rate 857 Drawn down pro-rata under US bank L/C 15% Cash down payment (may have been financed within a project/corporate credit) 100% Repayment usually begins six months after planned start-up in equal semi-annual instalments, with the banks usually paid out first, Pefco next, and US Exim last. Medium-term credits ("supplier credits") are issued for US equipment exports for terms up to five years, again for 85% of the equipment costs although the exporter is expected to bear at least 10% out of that 857 for its own risk. The buyer is required to be a first-class credit such as some governments or highly credit-worthy companies. Otherwise a bank L/C would be required. (This may be wrapped into an overall project-finance package for a minerals development. The project-finance banks provide an L/C to US Exim instead of funding that portion themselves.) US Exim guarantees 100% of the political risk and either 85% or 95% of the commercial risk for

Jan 1, 1985

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946