Search Documents

By R. Wiesenthal

A method is developed for improving the low recovery efficiency which results when viscous oils are flooded by water. Viscous oil has been diluted with a lighter liquid miscible in it in any ratio which produces a mixture possessing a reduced viscosity and which is then displaced by water. Light gasoline was used in these tests to reduce the viscosity of the oil in place. Oils possessing viscosities in the range of 1.28 to 324 cp at the test temperature of 30C were displaced from a cylindrical unconsolidated sand core, with a length of 2 m (6.6 ft) and a diameter of 10 cm (3.9 in.) at a flood of 6.27 cc/sq cm/hr. In two test series up to I PV of light gasoline was injected into the core before water flooding. In the first series the recovery of a low-viscosity oil (1.28 cp) increased as the volume of light gasoline was increased. However, only the oil which could not be recovered by water flooding alone could be replaced by the light gasoline. In the other series, the recovery of a more viscous oil (13.5 cp) was not increased even if large quantities of light gasoline were injected. An oil bank built up ahead of the water front so that the flood water met with equivalent saturation conditions, as would be the case in flooding solely with water. However, the recovery of more viscous oils could be increased substantially when the core was first flooded with water, followed by a slug of light gasoline, and then flooded with water again. Furthermore, an oil bank ,built up ahead of the second water front. The formation of this oil bank is particularly favorable for the displacement process; the greater part of the light gasoline injected was pushed out of the core ahead of the oil and recovered. Using a light oil of low viscosity, it was possible to replace only the residual oil that could not be recovered by water flooding by the light gasoline. As the basic study had shown that highly viscous oils could be recovered by flooding first with water, then with light gasoline, followed by a second injection of water, the study was extended by tests made with reservoir fluids and cores taken from the low-gravity oil reservoir of the Wietze field, Germany. A great increase in recovery over flooding with water alone was obtained in these tests. The results may show a way to recover high-viscosity oils by a comparatively simple flooding procedure. INTRODUCTION In fields where oil recovery has not benefited from natural water drive, increased recovery may be obtained by the injection of water into the reservoir, especially in the case of fields which produce high-gravity, low-viscosity oil. There is a rather close relation between the viscosity of the reservoir fluid and the recovery that can be obtained by water flooding. As the viscosity increases the oil recovery decreases proportionately, so that an oil viscosity about 30 times that of water is generally considered to be the upper limit for an economically successful water flood.' This limitation has been recognized theoretically by Buckley and Leverett,' and has been verified by numerous laboratory flooding tests, such as by Croes and Schwarz,V n the viscosity ratio range of oil to water from 1 to 500. The reason for the inferior recovery of viscous oils by water flooding can best be understood by considering the mechanism of flood tests. In such tests water is introduced into one end of a sand-packed tube which is saturated with oil of the viscosity to be tested, and oil is produced from, the other end. Oil, with a viscosity lower than that of water, is pushed ahead of the advancing water with considerable uniformity, and irregularities in the displacement process tend to be eliminated as the oil saturation decreases and the water saturation increases. However, oil recovery is not complete, for the water forms interfaces with the oil and traps residual oil droplets in certain of the pore spaces. These residual oil droplets are distributed rather uniformly through the sand, and they are not susceptible to recovery regardless of the amount of water passed through the test cylinder. In the case of an oil possessing a viscosity greater than that of water, the injected water tends to move irregularly through the sand in the test cylinder. At the place in the sand where initial water movement takes place, resistance to the movement of water is lowered and the water finger so formed will grow perceptibly; it will extend to the outlet end of the test cylinder so that a breakthrough of water takes place long before much of the oil-saturated volume of the sand has come in contact with water. Once the breakthrough of water takes place, the water-oil ratio is gradually approaching the economic limit, even though much of the oil in the test cylinder remains unaffected by water. Disconnected drops of oil are trapped in the portion of the sand that has been invaded by water, just as when an oil of low viscosity is flooded. The poor recovery of the more viscous oils, therefore, is due to the irregularity of water movement through the test cylinder, and the rate of water movement through restricted sections of the oil-saturated sand increases with the more viscous oils. There are three ways whereby the recovery of viscous oils by water flooding can be improved:' (1) adding materials which will increase the vis-

Jan 1, 1965

By R. W. Nash, A. E. Schwaneke, V. R. Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western prophyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized - 2.5 + 1. 3-cm (- 1 + 1/2- in.) ores from the Kingston (0.9% Cu) and Centennial (1.6% Cu) mines of Upper Michigan. Concentrates of 4.0% and 7.5% Cu, respectively, were obtained at recoveries of 85 and 80% of

Jan 8, 1978

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By Jun-Yan Chen

Ground control problems in sublevel caving become evident as the rock pressure increases with depth. Recently, a finite element analysis of the stability problem of the sublevel caving method was completed by the author. This paper summarizes the results of stress analysis in sublevel extraction drifts under different field stress conditions by using linear elastic and nonlinear elastic-plastic finite element modeling techniques. A critical stress concentration will occur in the uppermost sublevel drifts beneath the caved area or blasted ore area. During the blasting and drawing cycle, a tensile and shear failure condition could develop in the center extraction drift when it would be mined last. Under a high horizontal stress field condition, almost all tensile stress in the back of the extraction drifts will be eliminated and only slight yield can be seen in the floor of the extraction drifts. Compared to the cases under the stress field where vertical stress is the dominant factor, the total yielding zone will be greatly reduced because of an in- creasing horizontal stress field with depth. However, it is predicted that the center of each ore column side will experience excessive shear stress that probably will result in ore failure. The two major conclusions drawn from this study to improve the overall stability of sublevel caving are: (1) the drift width must be carefully controlled and an appropriate stoping sequence selected; and (2) the sublevel caving method can be used in deep min

Jan 1, 1983

By E. A. Jones

THE Southeast Missouri division of the St. Joseph Lead Co. normally hauls and hoists over 5 million tons of lead ore each year. This ore is mined in the stopes and headings of 20 mines, hauled to a main line system, see above, and transported up to 6.4 miles to ore-hoisting shafts. Average haulage distance is 2.16 miles. A few years ago a distinguished mining engineer visiting this area for the first time remarked, "You do not have a mining problem; yours is a haulage problem." Its relative importance may be gaged by the fact that mine haulage represents about 25 pct of the total cost of mining ore, the most costly single underground operation. The Southeast Missouri lead belt is a mining district located about 65 miles south of St. Louis. This district is roughly 6 miles wide and 10 miles long. The ore horizon lies about 400 ft below the surface where most of the ore is mined from flat-lying beds of dolomitic limestone. This paper deals with the central part of the district, namely, that portion which contains a group of interconnected mines all in a central haulage system, serving four hoisting shafts. The two major hoisting operations are carried out at Federal No. 17 shaft and Leadwood No. 12 shaft. No. 17 accounted for about 70 pct of the ore hoisted in the district during 1950, averaging about 14,000 tons per operating day. The underground dumping and skip-pocket system at this shaft is similar to those of the other shafts except that it has two rotary dumps. The other ore-hoisting shafts have only one. It might be mentioned that waste rock is hoisted at still other shafts, hauled off, and dumped on the surface by trucks. The hoisting shafts are on a connected system of about 200 miles of underground 24-in. gage main line railroad. There is also the Bonne Terre system, with its own ore-hoisting shaft, which consists of 13.5 miles of 24-in. gage main line, located in the extreme north portion of the lead belt area. Smaller outlying mines such as Doe Run No. 12 and Hayden Creek operate on trackless or shuttle car haulage. In addition to the system of main line haulage, each contributing mine group has its own extensive system of stope or heading railroad. Trackless mining is making considerable headway in the Lead-wood and Desloge mines. Here the shovel loads into a shuttle car which in turn dumps into mine cars spotted on the main line track system. When the merits of underground haulage and surface transportation are compared, it must be remembered that in early days there were many individual

Jan 1, 1954

Cooperation will be the keynote of the meeting of the Institute that will be held in New York on February 17 to 20. Arrangements are being made for two joint sessions with the Canadian Mining Institute, on the same day, which therefore will be known as Canadian Mining Institute Day. On the afternoon of Wednesday, February 19, there will be a joint session with the American Institute of Electrical Engineers. Besides, we will receive six or eight papers through the National Research Council, four of which will be presented at the National Research Council Session. In March, at the next meeting, of the Canadian Mining Institute, there will be an American Institute of Mining Engineers Day. The plan is to have the same subjects discussed at both meetings, but by different speakers. One speaker on each subject will represent the Canadian Mining Institute, and one speaker the American Institute of Mining Engineers. The Canadians and the Americans who will speak in Canada are expected to attend the discussion in New York. In addition the discussion at the New York meeting will be sent to Canada in printed form, so that the Canadian discussion will be a continuation of the former. At the joint session with the American Institute of Electrical Engineers, there will -be presented six very important papers on the subject of Electric Welding, one by the Chairman of the Electric Welding Research Committee of the National Research Council, another by the Chairman of the Metallurgical Sub-committee of that same Committee, and a third by Comfort A. Adams, President of the American Institute of Electrical Engineers and Chairman of the Welding Committee of the Emergency Fleet Corporation. We will receive six or eight papers through the National Research Council. These papers are results of recent investigations and represent the last word in their respective subjects. The excursion on Thursday, February 20, will be to Newark Bay to visit the Federal Shipyard where the first, electric-welded ship is being built. Philip W. Henry is chairman of the excursion committee of arrangements.

Jan 1, 1919

By P. B. Bucky

IN previous publications1 it was shown that a scalar model of any weighty structure, where the stresses produced are mainly due to gravita-tional forces, will behave similarly to its prototype if the model and proto-type material are the same arid the model is placed in a centrifugal field of force (substituted for the gravitational field) which has been increased in the same proportion as the linear model scale is decreased. This principle is now being applied to a study of the behavior of mine structures in an attempt to determine the laws that control them. The importance of using models as a means of solving mining problems has been discussed previously, yet it may be well to reiterate here that this method of research and type of solution have been productive of far-reaching results in other engineering fields, notably those of hydraulics and aerodynamics. Model research is a comparatively cheap and time-saving method of checking practical experience. Up to the present time the best guide to what will happen underground has been the judgment of the man who has observed most and been longest acquainted with the local conditions. His experimental work underground is limited by the elements of cost, time and danger, while failure is seldom permissible. In a model, as in a test tube, all elements that affect the solution of a problem are under definite control. Each element may be varied independently at will and its effects noted. Experimental work on a small-scale model may there¬fore be performed at a comparatively small expenditure of time and money, instead of on a full scale in the mine, where the cost, time, and danger elements are necessarily great. The experiments described in this paper are to be considered as part of a progress report and a continuation of Technical Paper 425. One object of the research program is to make each experiment point the way for further research on that particular phase of the general problem. The results and conclusions presented here are therefore not to be considered as final, but are to be interpreted as

Jan 1, 1933

By R. G. Lazzell

THE British are worried about the postwar possibilities of their coal mining industry. Indeed, there are causes for this worry, with the aver- age 1943 cost of production at about $5.40 per long ton, compared to $3.20 in 1938. Average production per man day has dropped from 1.12 in 1938 to 1.03 long tons in 1943. As a comparison, production per man day in the United States is approximately 5 long tons. The average day wage in the British mines is now a little aver $4; in 1938 the average day wage was about $2.25. Great Britain produced 227 million long tons in 1938 from their deep mines, and in 1943 production was 194.5 million, with an additional 4.5 million from strip mines. To meet present wartime needs, output is being supplemented by the production of strip- mined coal, an industry that did not exist prior to the war. Strip mining is now producing at the rate of 15 million long tons per year.

Jan 1, 1944

Carlisle: This is August 1960 and I am sitting across the table from Henry DeWitt Smith. We both took the mining course at Yale the same year; and here we are, over fifty years later, at Nantucket Island where we have spent quite a number of summers together. Now, let's start the questions with something about the center of your career. Let's say Tsumeb; not about the mine itself which people know, but some of the details on how you happened to take it over for Newmont. Mr. Smith: I first heard of Tsumeb, a famous German mine, through our own associates O'okiep Copper Co. From 1935 on, the local management at O'okiep, being reasonably close, kept the New York office informed. It served as a listening post for new mine development, as well as being a highly profitable copper mine in the northwest Cape Colony. We had all known of a famous German mine in South West Africa called Tsumeb. But it had a reputation for not welcoming visiting engineers. One engineer who went to this property for the Ministry of Supply in 1943, '44 and '45 was Arthur Storke. He was much impressed with possibilities of profitable operation. This mine had been operated by a German company since 1910. It was finally taken over by the Custodian of Enemy Property for the Union of South Africa.

Jan 11, 1963

By Persifor Frazer

The accompanying diagrams represent a lamp provided with certain improvements which render it more serviceable for the use of the engineer or other mining official who is often compelled to visit several mines a day remote from each other, and may be called on to use the magnetic needle in any or all of them. These requirements demand that the material of which it is made should be copper, and that it should be capable of being closed oiltight, for emptying and refilling the lamp at each mine would be a less expeditious as well as a less cleanly process, and transporting a lamp of the ordinary kind over rough roads on horseback or in wagon, would result in spilling the greater part of its contents. The general form of the lamp, including the false back to keep

Jan 1, 1882

By M. Kaitz

A continuing discussion in both the petroleum engineering and economic literature is directed to the difficulties encountered in the use of discounted cash flow rate of return (DCF) as a measure of investment worth. Although useful in most Instances, DCF has been criticized because it is time-consuming in its trial-and-error solution, theoretically invalid, not adaptable to cash flow streams yielding multiple return solutions and not entirely reliable in selecting between mutually exclusive investments. The theoretical invalidity of DCF stems from the reinvestment assumption implicit in the calculation that earnings are reinvested at the DCF rate. The emerging consensus of the economic literature is that the net present value or the present worth of the net cash flow stream (discounting at the average opportunity or cost of capital rate) is more correct and reliable. Other criteria proposed have been ratios of net present value divided by initial investment or by present value of all investments in a project. All of these criteria are simple to determine and explicitly assume a reinvestment rate for [he income generated by a project. This paper develops and discusses a theoretically valid profitability criterion which is simple to compute and retains the appeal of a percent return on investment. It is called "percentage gain on investment" or PGI. It measures the gain an investment is expected to realize over like capital invested in the average opportunity and explicitly considers reinvestment potential. Why add another Concept to the large array of investment criteria now available, any one of which, or perhaps a combination of several, appears to embrace the form's (or individuals) objectives? The answer is that not one of the existing criteria provides both a readily comprehensible and theoretically valid measure of risk coverage that has general application. The proposed PGI does fulfill these requirements. INTRODUCTION An ancient expression warns that "one must yield to the times" — there are better ways of doing things. A review of the petroleum engineering and economic literature on one topic alone, measurement of investment worth, certainly is witness to this truth. In use for a number of years, the DCF has recently received attention, directed mainly to its theoretical invalidity. Several alternatives to DCF have been proposed to provide a valid, simply determined criterion to describe investment worth and to overcome the criticisms previously mentioned. This paper introduces another method called percentage gain on investment (PGI) and is proposed as but one of several yardsticks that should be used in making investment decisions. MEASURES OF INVESTMENT WORTH This paper will consider only those criteria which give weight to the time pattern of future earnings. These criteria are usually compared with an average opportunity rate or cost of capital of the firm to judge the relative worth of the investment. For purposes of demonstration, a 9 percent average opportunity rate will be used throughout this paper. Implicit in the DCF calculation is the assumption that earnings are reinvested at the DCF rate. Some argue, though, that there is no reinvestment assumption,' that the DCF rate is simply that maximum rate of interest one can pay on the investment over the life of the project and break even. The determination of DCF is accomplished by discounting the net cash flow stream at that rate (DCF) which will yield zero. The question is: why should reinvestment potential be explicitly considered in calculating return on investment or other criteria measuring economic worth? Perhaps the answer lies in consistent or equal treatment of future cash flow. It appears entirely illogical to give different present worth value to $1 received, say, 10 years from now, which is the circumstance resulting in comparing projects with different DCF returns. In fact, $1 received in 10 years has the same value regardless of which project generated the income. DCF return thus favors investment projects which are expected to provide early income as compared to those providing long-term income. Not surprisingly, the controversy on reinvestment assumption is an old one. Hoskold' discussed this same problem in 1877. He considered the future income from mineral properties as an annuity or a series of fixed future payments. (As will be demonstrated, his equation can be modified for variable income.) Prior to Hoskold, the value or what one could pay for the mine, was determined with the use of standard, single-interest tables. Here is what Hoskold said with regard to these tables. "This table, and others of its kind, to be found in most works on annuities, is constructed correctly according to

By Ernest R. Lilley

While American scientific literature contains much information upon geologic conditions controlling the production of oil in Rumania, copper in Chile, and other fuel and metallic resources in many foreign countries, it is singularly lacking in data about the nonmetallics outside of the United States. Thus, though the United States is the outstanding market for European high-quality refined kaolin, and for the chinaware, porcelain, and other products of the European ceramics industries, American literature contains only the briefest references to the deposits from which the raw kaolin utilized is obtained. To the writer, to whom has come in the past year the opportunity of visiting a number of these deposits personally, they have proved of extreme interest both commercially and geologically. It is the latter phase that is discussed in this paper. The older and now largely crystalline rock areas of France, Germany, and other parts of western Europe contain numerous pegmatite dikes of which the upper portions have been subjected to surface weathering and kaolinization in much the same way as those of the eastern portion of the United States. Like the latter, the European pegmatite kaolins have long been known for their freedom from iron and other impurities offensive to the china and porcelain manufacturer. Unfortunately, they are also, like the American deposits, individually of small size and noted for their high costs of production. Deposits of sedimentary clay similar in many respects to the high-quality sedimentary kaolins of Georgia and South Carolina are known and worked, notably in southern Germany and in the Newton Abbott district of Devon and Dorset in England. In general, their relationship to the parent rock from which they were derived is more evident than in the United States and the individual deposits are of smaller areal extent and less regular in outline. While these deposits are of considerable economic importance they did not, because of their similarity to deposits in America, attract and hold the interest of the writer to the extent that several other types of deposits did. It is to the latter, which are so different from the kaolin

Jan 1, 1932

Discussion of the paper of E: D. Gardner, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1467 to 1471. H. V. WINCHELL, Minneapolis, Minn.-There are two questions I should like to ask: First, does the Department still adhere to the decision made in the East Tintic case? Second, does the Department require placer ground to he of such value that, in the opinion of the Forest Service employees, it will pay to work, before admitting the location to be valid? T. C. HOYT,* Ogden, Utah.-With reference to the first question: the Department does not hold to that decision, as it was reconsidered by the Secretary Of the Interior, and the Department is governed by the decision of the Secretary Of the Interior, on those points always. The Department of Agriculture makes no decision as to what constitutes a sufficient discovery. The mineral examiners simply report their findings and Opinions. These are transmitted to the chief of the field division of the General Land Office, who in turn transmits the reports to the Commissioner Of the General Land Office, who decides whether the report raises an issue requiring a hearing. If a hearing is ordered, expert testimony is given on the question of the discovery, as well as the evidence of practical people who operate in the vicinity of the claim in question. As to the extent of placer values considered sufficient to justify a location, my answer will need a little amplification. I couldn't answer it directly for the reason that sometimes people resort to placer claim location as a means of acquiring land for Other purposes than placer mining, which makes it absolutely necessary that the government give close attention to the question of whether good faith has been shown, as it is the evidences of good faith that largely determine whether a report adverse to a claim shall be made. That is a difficult point to cover sometimes. For instance, in the region I have recently visited there are some 17 miles of a valley, from ¼ to ¾ mile in width, all covered by placer locations. It is valuable stock-grazing land, and is stocked at the present time. It also contains a stand of timber, and is on the watershed of an important stream-important from the fact that it furnishes the water supply to government storage reservoirs, and to pending reclamation and Carey Act projects. In this case the placer claims will not be disturbed as mere locations. They will simply remain there, and there will be no action with reference to them until the claimant asks for patent or, before patent, begins to denude that watershed and remove that timber. Then the government would direct that the mineral experts go on to the ground, examine it, prospect it, and submit their report, with a view to seeing if

Jan 11, 1914

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By A. W. Fahrenwald

The physics and chemistry of the flotation process are not well understood. Many papers dealing with the theory of flotation have been published but most have been narrow in their viewpoint. No theory advanced has done more than explain, more or less satisfactorily, various isolated phenomena. Scientists have done little with the problem, doubtless because they have not seen sufficient of the practical side of the subject to have their interest aroused. Any attempt to explain the mechanism of flotation that considers only contact angles, surface tension, adsorption, the floating of needles, flocculation, or any other single and narrow phase of the question is sure to be disappointing. Flotation is a problem of colloid chemistry and must be studied as such. In a broad general way, flotation is a process involving and operating by virtue of surface reactions. The term "surface reactions" may be open to criticisms. Many chemists give the term "reactions" a definite and restricted meaning and to such the term may connote change in atomic grouping in strict stoichiometric ratios. While Langmuir looks upon adsorption as a reaction, and there is much evidence in support of this view, we may look on adsorption as a physcial process as far as this paper is concerned. The term seems well suited to the work in general. Presumably these reactions are reactions between the same kinds of forces (electrical) and differ only in degree and in the surface manifestations produced. This premise seems logical if we accept the theory that the atoms of dl elements are made up of grains of electricity, having mass and charge, called electrons; and that atoms differ from one another only in the number and arrangement of the electrons about a positive nuclear

Jan 1, 1924

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inor-ganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of furnaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the produc-ing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the struc-ture. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate.

Jan 1, 1937

By John Chipman, Carl F. Floe

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By Carl F. Floe, John Chipman

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By Charles C. Templeton

Any explanation of the nature of multiphase fluid flow through porous media must ultimately involve a knowledge of the mechanism of such flow through the individual pores of the medium. To provide quantitative information of the latter type, a study was made of gas-liquid and liquid-liquid displacements in single uniform Pyrex capillaries with diameters as small as 4 microns. Quantitative observation of air-liquid displacements with zero contact. angle indicates the adequacy of a model based on Poiseuille's Law and the independence of capillary pressure and interfacial velocity. Consequently, this work discounts previous claims that flow is abnormally retarded in very small capillaries. For the displacement of a very viscous oil by water in a capillary initially filled with water, flow is faster than predicted by the above model. This behavior is probably due to the existence of a thin annular film of water between the oil column and the capi1lary wall as postulated by Yuster. INTRODUCTION The need for experimental observation of the microscopic nature of multiphase fluid flow, to further the understanding of the results of macroscopic flow investigations, has been previously recognized. Chatenever and Calhoun1 in connection with the API Project 47B have extensively studied the flow of fluids through layers of glass or lucite spheres between glass or lucite plates. Lowman2 prepared an interesting film concerning flow in a single capillary, using an apparatus which made a moving interface appear stationary in the field of a microscope. The purpose of the present investigation was to deter- mine what contribution might be made to this field by comprehensive quantitative observation of gas-liquid and liquid-liquid displacements in single capillaries of uniform, very small diameter. The techniques used are similar to those of Lowman but incorporate improvements necessary for quantitative work. Quantitative observations must begin with fluids of simple chemical composition to provide a basis for analyzing the more complex behavior that may be expected with natural reservoir fluids. However, some qualitative observations on systems involving crude oils are presented. Experiments of this sort involve the observation of the velocity of the interface separating two fluids, and have been performed in horizontal or vertical capillaries by several investigators.3,4,5,6,7,8 The most general treatment of their mechanics, by Brittin,9 involves forces due to capillarity, viscous resistance, gravity, an "end-drag" effect, and the rate of change of momentum of the capillary contents. Since the range of pore diameters of interest in petroleum reservoirs is about 0.1 to 100 microns, it was desired to perform these experiments in the smallest capillaries possible, to ascertain whether capillary diameter had any effect on the existing theory based on data from larger capillaries.* It was also important to be able more systematically to vary the direction and rate of displacement than was done by previous investigators. Finally, to concentrate attention on viscous and capillary forces by eliminating gravity as a parameter, this study involves only horizontal capillaries. The work of Eley and Pepper' with a "large" (0.766-mm diameter) horizontal capillary is the previous investigation which is most similar to the present method of quantitative observation. Here capillaries with diameters as small as 4 microns will be studied.

Jan 1, 1955