Search Documents

By J. L. Bray

LEAD has often been suggested as a protective coating for iron and steel. Such a protective coating should possess: (1) good adhesion, (2) durability, (3) ease of application, (4) freedom from pinholes, (5) good appearance and (6) low cost, but, unfortunately, lead coatings so far produced do not have all of these characteristics. Because of the necessity of carrying out the coating process cheaply, and because lead solutions have poor plating characteristics, most of the efforts have been directed toward the hot-dipping process rather than electroplating. The hot-clipping processes using lead have not been successful chiefly because of the lack of adherence between iron and lead. In any coating process involving iron a bond can be obtained only by the formation of an intermetallic compound, the formation of a solid solution, or mechanical means. Lead forms with iron two immiscible liquid solu-tions, and in the solid state no intermetallic compounds or solutions. It is necessary, therefore, to employ some other element or elements as a binding agent. Tin may be used as in terneplate, or copper in the form of a thin film of electrolytically deposited metal to which the lead will adhere. Because of its physical and chemical properties, lead as a coating medium would undoubtedly be limited in its use to sheet and wire and then only when the article is not subject to abrasion or wear. A very large tonnage of these products are being used under such conditions and a successful lead-coating process should be a valuable contribution to the science. Two other difficulties stand in the way of successful lead coating-that of poor appearance of the weathered surface and the tendency of the lead to form pinholes during solidification. Since lead is commonly accepted as cathodic to iron, these exposed areas are ones of accelerated corrosion.

Jan 1, 1937

By B. C. Allen

Liquid surface tensions of copper and 18 Group IV-A to VIII transition metals (Ti, Zr, Hf, V, Cb, Ta, Mo, W, Re, Ru, Rh, Pd, Os, Ir, Pt, Fe, Ni. Co) have been measured by the static pendant-drop and dynamic drop-weight methods on the same rod sample. The drops were formed by electron-bombardment heating in high vacuum. Application of necessary corrections enabled determination of surface tensions to k2 pct and agreement between methods to * 1 to 4 pct for all the metals studied. Evidence is presented that the liquid surface was well screened by metal vapor, suggesting negligible adsorption of gaseous impurities and that the surface tensions measured are characteristic of the metals involved. Correlations between liquid surface tension and melting point, molar volume, heat of vaporization, and atomic number are presented and discussed. Temperature coefficients of surface tension were calculated using Eötvös' law. SURFACE tension and interface energies of metals are the result of incomplete atomic coordination resulting in a force perpendicular to the boundary, tending to minimize its area. These energies are important in many phases of metallurgy, including microstructure, sintering, joining, electronic emission, and lubrication, which in turn affect many physical and mechanical properties of metals. Liquid surface tension refers to the interface between the liquid and its own vapor or nonreactive atmosphere, and is considered a physical property of the liquid. Since equilibrium shapes can be readily obtained with liquids, the units of surface tension (force per length) and interface energy (energy per area) are interchangeable. Thermo-dynamically, the surface tension ?LV is given by the change in free energy F with surface area A at constant pressure P, temperature T, and composition N: for commercially important refractory metals, vanadium, columbium, tantalum,13,14 molybdenum,14 and tungsten,l5 and none for the rare platinum-group metals and rhenium. Measuring the surface tensions of transition metals is difficult because of their high reactivity and melting points. Of the many techniques available,16-18 the pendant-drop 19-21 and drop-weight methods17,22 are considered superior because they can be modified to eliminate persistent sources of contamination such as supports and capillaries necessary in the popular sessile drop, capillary rise, and maximum-bubble-pressure techniques. The necessary modification is to melt a drop on the tip of a vertical rod, which provides support through a solid of the same composition.13,15 The object of the work was to study the surface-tension behavior of copper and transition metals, having reasonably low vapor pressures. Liquid surface tension of each pure metal was systematically determined by using a combination of the static pendant-drop and dynamic drop-weight methods on the same rod. Liquid drops were formed by electron-bombardment heating in high vacuum. EXPERIMENTAL WORK As indicated in Table I, the metals studied were high purity and generally were obtained in rod form. The exceptions were titanium and zirconium, which were machined from crystal bars, and molybdenum (tot 11, osmium, and ruthenium, which were sintered and arc cast into rods. All the metals were ground or swaged to desired sizes between 1- and 7-mm diam, and centerless ground round and smooth to a finish better than 50 µ in., rms. Each rod was thoroughly cleaned with steel wool, degreased, acid etched, and dried. In a typical run, the rod was vertically clamped in a modified floating-zone electron-bombardment furnace designed after Calverley23 and Carlson.24 The specimen was outgassed and maintained positive at several kilovolts in a dynamic vacuum of 10-5 to 10-7 mm. The bottom end was enclosed by a tantalum pillbox and heated by electrons emitted from a hot concentric tungsten filament mounted on a movable bracket. The bombardment power was slowly raised until melting was observed. Power requirements ranged from 30 w for copper to 1300 w for 4-mm tungsten. The stabilized and out-gassed drop of near-maximum size was photographed at 4. 1X on panchromatic film at desired time inter-

Jan 1, 1963

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By J. O. Lewis

Oil wells usually reach their maximum daily output shortly after they are completed. From that time they decline in-production, the rapidity of decline depending on the output of the wells and on other' factors governing their productivity. The production curve of a well shows the mount of oil produced per unit of time for several consecutive periods; if the conditions affecting the rate of production are not changed by outside influences, the curve will be fairly regular, and, if projected, mill furnish useful knowledge as to the future production of the well. By the aid of this knowledge the value of a property may he judged, and proper depletion and depreciation charges may be made on the books of the

Jan 2, 1918

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By G. Ansel, J. O. Betteron

THE PURPOSE OF THIS PAPER is to give a brief picture of present day magnesium rolling practice, to elaborate on laboratory and development rolling experiments; and finally, to discuss the possible Future rolling of magnesium. The present production practice is so varied between various mills that it can only he concluded that no single producer is now using a process that is outstandingly superior to others. In view of this, only the general features of present day production practice have been presented and attention is focussed on the results of laboratory find development rolling of magnesium-base alloys as indications of the Future trend of magnesium rolling. MAGNESIUM ROLLING LITERATURE The literature relating to magnesium rolling is divided into three groups: the deformation mechanisms of the hexagonal magnesium crystals, the metallurgical aspects and laboratory type experiments in rolling, and finally, the articles on production rolling methods. This literature was reviewed and is summarized below. In the first group of references, the existence of basal slip in magnesium single crystals was shown by Schiebold and Siebel1 and of {102} twinning by Mathewson and Phillips2, Schmid3 predicted and partially established {101} slip at hot working temperatures. Bakarian and Mathewson4 confirmed the above and eliminated {101} twinning as a probable deformation mechan-

Jan 1, 1948

By L. H. Levenson, Charles S. Barrett

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By Charles S. Barrett, L. H. Levenson

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By M. S. Seltzer

High temperature steady-state creep rates have been determined jor lead sulfide single crystals whose defect concentrations were fixed by equilibration under controlled sulfur pressure. The activation energy of creep, Qc , for undoped lead sulfide, is a function 01 composilion, decreasing from 2.9 to 2.2 ev as the carrier concentration increases from 9 x 1016 to 8 1018 electrons cm-3 for lead excess crystals, and increasing from 1.7 to 2.3 ev as the concentration of holes increases from 4 x 1017 to 1 x 1018 cm-3 in sulfur excess material. For five different composilions, Qc for undoped and bismuth-doped crystals has been found to be equal to Qpb + Qs, the self-diffusion activation energies for lead and sulfur in PbS. It is well-established1 that high-temperature steady-state creep of pure metals is a diffusion-controlled process, where the activation energy of creep is equal, within experimental error, to the activation energy of self-diffusion. The relationship between the activation energy for steady-state creep and those for self-diffusion in binary compounds is more complicated, however, because two different diffusing species must be considered, and becayse the activation energies may be influenced by compositional variations and by foreign atom additions.2-4 In some cases experimentally determined creep activation energies are correlated with those for self-diffusion of the slower-moving species, but such agreement is by no means universal. Interpretation of experimental results is difficult because few investigations include measurements of creep rates and self-diffusion coefficients of both diffusing species on single crystals of similar composition and foreign atom concentration. The objective of this investigation, therefore, is to determine the influence of stoichiometric defects and foreign atoms on steady-state creep and self-diffusion for a well-characterized binary compound. Lead sulfide, a compound semiconductor which crystallizes in the NaC1-type structure, and whose homogeneity range includes compositions on either side of the 1:l atom ratio, was chosen for study in this investigation. The pressure-temperature-composition relations for PbS are available,5,3 and deviations from stoichiometry may be monitored by electrical measurements.7 Single-crystal specimens are available to allow observation of effects due to bulk phenomena without interference from grain-boundary effects. These crystals have been employed to determine steady-state creep rates under compressive stress for "pure" and bismuth-doped PbS as a function of sulfur pressure and temperature as well as crystal orientation and applied stress in order to establish the relationships between defect concentrations and creep rates. EXPERIMENTAL PROCEDURES Crystal Growth. Lead sulfide crystals, prepared by the Bridgman method, are grown in evacuated quartz crucibles, filled with almost equal atomic proportions of high-purity (99.999 pct) lead and sulfur, and heated to a temperature above the melting point of PbS (about 1127°C) so that the lead and sulfur react to form molten PbS. The crucible and melt are dropped through the hot zone of the crystal-growing furnace at the rate of 1 cm per hr. The maximum melting point of PbS is slightly on the lead-rich side of the 50:50 composition; hence crystals grown from a near stoichiometric melt are usually n-type semiconductors containing excess lead atoms. Typically the lead excess concentration in solid solution with the PbS is 3 x 1018 atoms cm-3. Crystals containing either 1/20 or 1/2 mole pct Bi2S3 were prepared by addition of the foreign atoms prior to crystal synthesis. Preparation of Specimens of Controlled Stoichiom-etry. Since it is difficult to grow crystals of desired composition, the process of crystal growth and control of stoichiometry are separated into two distinct operations. Equilibration of as-grown PbS to a desired composition is most easily accomplished by first annealing the n-type crystals under high sulfur pressure (about 1 atm) at temperatures above 700°C. This process serves to put excess lead precipitates into solution, yielding 0 -type crystals upon quenching to room temperature. Inter diffusion occurs readily in crystals so treated, and the methods described by Bloem may then be employed to obtain crystals of controlled stoi-chiometry. For the creep measurements made in this study, this involves heating crystals in mixtures of H2 and H2S The equilibrium constant for H2S is given by: Thus the sulfur partial pressure is obtained from knowledge of the H2/H2S ratio and Kh2S for the temperature in question. Fig. 1 shows the p-T-x diagram for PbS. It can be seen that, within the stability limits for single-phase lead sulfide, desired compositions may be obtained by equilibrating under a specified sulfur pressure and temperature. Characterization of Crystals. The principal methods for evaluating PbS crystals include measurement of electrical properties and mass-spectrographic analysis. The measured electrical parameters include Hall coefficient, conductivity type, and electrical resistivity Bloem7 has shown that there is a 1:l relation between the defect concentration and carrier concentration obtained. Hence, if the contribution to the carrier con-

Jan 1, 1968

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent. of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART 1.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent. of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust.

Jan 1, 1929

IT may perhaps seem to you that I have deviated from sequence by having entered into the narration of this arrangement of the bellows, but, although they are not furnaces or vessels for containing the melts, they are essential agents for bringing to port the bark of your labors. Returning to our regular pathway, and supposing that, besides making the moulds, you have melted and cast not only statues and bells but also guns, it is true that a certain procedure is required in order to finish them. For this you should have the moulds full, and they should have come out very well, for in truth reason does not allow that they turn out otherwise for one who uses precaution. [II2V] Then you have taken your casting from the pit and have freed it of clay. Since I have told you nothing beyond this, do not be dismayed if you see the castings so rough and in a form that scarcely shows what they really are, for I wish to open up part of the way into the great labor of finishing them so that it may seem to you that you have been somewhat helped by me. Therefore, when it is a gun, first see that the iron spindle that has been placed in the middle of the core is taken out. You can do this easily by striking the heel of the core, especially if the spindle had first been covered with ashes, hemp, or a little rope. Then saw off the feeding head above the mouth, using either a dun steel saw with tiny straight teeth that has been tempered with oil or some other fat, or a hay sickle whose edge is gently hit by a little hammer. Then have the clay that is attached to the curls or other bronze parts lifted away with a chisel. Then with a scouring brush and water uncover the emblems, coats of arms, borders, and cornices that you made as ornaments. Striking it with a hammer, push inwards every superfluous bit of bronze. Finally, having cleaned the bronze by washing, scraping, and cutting away every bit of clay, strike its surfaces gently with a large hammer and thus make it very smooth. Likewise finish the mouth and all its cornices as exactly and completely as possible with files and any other instrument that serves best. Then take a long, powerful tool that has some steel on the point, made like a chisel and somewhat bent, or with three points like the iron blade

Jan 1, 1942

Charles H. Morgan, Worcester, Mass. (communication to the Secretary): In connection with Mr. Douglas's mention of the continuous charcoal kiln used at Kopparberg, some further data concerning this important invention may be of interest. Before giving these, however, I will say a word or two concerning other features of Swedish practice. In 1894 I spent two days at Soderfers with Mr. Tom Bergendal, the manager of the works, and was specially interested in the gas-producers and wood-drying kiln, illustrated in the paper contributed to our Transactions by Mr. Odelstjerna in that year.* The wood-drying kiln is, however, quite different in design and construction from Ljungberg's charcoal kiln. In the summer of 1894 it was discovered that by placing the gas-producer as close as possible to the open-hearth furnace, and working the producer hot, ordinary weather-dried wood, still containing a considerable percentage of moisture, could be used to advantage in the melting-furnace. Hence, the dryingkiln was needed for wet wood only. One of the iron-works of the Udeholm Go. was the first to adopt the Lundin saw-dust gas-producer and condenser, enabling them to make gas from saw-dust containing 45 per cent. of moisture, and convey the gas from the condenser through wooden pipes to the Siemens steel-melting furnace.† This sawdust gas gave very satisfactory results in iron-works; but the proprietors experienced much trouble by reason of the pollution of rivers by the tar-water from the condenser. On my visit, in 1894,I found that the Udeholm Co. had put in for their steel-melting furnaces the same wood-gas producers

Jan 1, 1899

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By G. L. Oldright, F. W. Schroeder

Very great changes were made in the dimensions of the smelting hearths of the furnaces in the period from about 1800 to 1906, the length increasing from about 11 to 116 ft., and the width from 8 to 19 ft. During this time the tonnage smelted increased from about 9 to 250 tons per 24 hr., and the tons of charge smelted per ton of coal increased from 0.77 to 4.3. Dr. Mathewson3 noted no great difference in the "fuel ratio" (i. e., the amount of charge smelted per ton of coal) as the furnace at Anaconda was increased in length by stages from 85 to 116 ft. (The percentage of copper in the slag, however, was lowered from 0.42 to 0.36 per cent. The other components of the slag were not given.) Lump coal fired on grates was the fuel used during this period. The practice in operating the furnaces over such a length of time naturally varied considerably, and there were differences in composition and nature of the charge, yet it may he considered that the improvements made were due largely to increases in the size of the furnace used. Doubtless some credit should be given to improvements in operating technique, like changes in the methods of firing the lump coal. However, the greater part of the advance was probably due to factors influencing the

Jan 1, 1928

By Warren Howes, C. O. Anderson, Robert E. Illidge, M. D. Harbaugh, S. J. Burris

The Tri-State zinc-lead mining district embraces an extensive area, including the northeastern part of Ottawa County, Oklahoma, the southeastern part of Cherokee County, Kansas, and adjacent portions of Missouri, mainly in Jasper County. The Oklahoma-Kansas portion of the district, in the vicinity of Picher, Okla., has been the principal producing area since 1917, and the present milling practice in that section is the subject of this paper. This district is the largest zinc-producing field in the United States. In 1926 it produced 55 per cent of the nation's zinc and 15 per cent of its lead, and in 1933 it produced 35 per cent of the zinc and 10 per cent of the lead. From 1842 to 1933, inclusive, the total output of the district was 18 1/2 million tons of zinc and lead concentrates valued at 818 million dollars. Of this production, the Oklahoma-Kansas, or Picher, field yielded over 9 million tons valued at over 400 million dollars. Mining operations in the Oklahoma-Kansas field near Picher and Baxter Springs began in 1915. The mills built it that time consisted merely of gravity concentration plants employing jigs and tables and the same flow sheets as had proved satisfactory with the free-milling ores such as were mined in the Joplin-Webb City fields in Missouri. The Kansas-Oklahoma ores proved to be much richer but also more refractory to treatment than those in the Joplin area, and contained a considerable percentage of zinc mineral not freed by the amount of crushing usually practiced in preparing the ores for jigging. Thus the old Joplin type of mill, with its usual two or four jigs and a few tables, proved inadequate and resulted in excessive tailings losses sometimes as high as 50 per cent

Jan 1, 1935

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal mere mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-pear periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu pd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu pd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can recovered by underground mining. 5) Some coal measures call best be extracted by surface mining

Jan 1, 1981

By Robert Rhea Goodrich

This research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward I?. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. Petrogeaphic DescRiption Texture: variable. Fine to medium mixed aggregate. Original Structure: Obscurc. Secondary structure: Fractured; healed. Mineralogy (Minerds are grouped for interpretation purposes and are arranged, in each group in approximate order of abundance)

Jan 1, 1916