Search Documents

By Reinhard Bott

The Companhia Mineira de Metais (Brazil) runs a Zn-recovery plant in Tres Marias, federal state Minas Gerais, Brazil. The Zn-production is about 65,000 t/a, This corresponds to a concentrate throughput of about 255,000 t/a with a Zncontent of about 29.5 % at an output of 85 %, The plant is run continuously 360 d/a and 24 h/d, respectively. From this it can be concluded that: Input: approx. 650 - 700 t/d ore-concentrate and approx. 29 t/h ore-concentrate, respectively.

Jan 1, 1990

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

The fraction of liquid phase in sintered ore can be the most important factor to determine the sinter quality and yield in sintering process. The generation ability of liquid phase for mixture of iron ore powders is determined by basicity, roasting time, roasting temperature and chemical composition of iron ores. Five different iron ores were selected in this study and the dried powders of iron ore and CaO reagent (<200 mesh) were homogeneously mixed together at their required proportions, then 15g of the mixture was pressed under a pressure of 20MPa to make a cylindrical sample with a diameter of 20mm. The sintering temperature in this study was kept at 1280℃, the gas phase is air, the holding time was varied with its three levels of 5min,10min and 15min. After that, the sample was cooled under room temperature in the air, and the cooled sample was analyzed by using zeiss optical microscope. The mineral phase compositions were quantitatively determined with an open source image processing software, Image J whicn can calculate the fraction of liquid phase. Besides, the study on how to estimate the sintering behavior of the raw materials in different conditions by the theoretical calculation is of vital importance, and the development of this will greatly improve the sintering production. Factsage will be used to calculate the liquid phases formulation during the sintering. Comparing the experimental results and the theoretical calculation shows that the mass of liquid phase increases with increasing basicity during the sintering, besides, the mass of calcium ferrite increases with increasing basicity. The generation ability of liquid phase of iron ores can be predicted through the experiment verification.

Jan 1, 2015

By Chunhua Liao, Chao Peng, Guangsheng Huo

To get the separation of tungsten and molybdenum, we adjusted the pH of the solution to 7, at which tungstate (WO4 2-) will be polymerized into HW6O21 5-, while molybdate will still exist in the form of MoO4 2-. Two strongly basic anion exchange resins (D201, D213) were experimented for the separation of tungsten and molybdenum. The results of condition experiments indicate that D213 resin performs better in the treatment of lower concentration solution A (WO3 10g/L, Mo 4.12g/L) with a separation factor as high as 10.64. While D201 resin is more suitable for the high concentration solution B (WO3 70g/L, Mo 28.97g/L) with a separation factor of 6.9. The results of column testing performed on D213 resin show that the solution after loading process with a mass ratio of Mo/WO3 = 50 and the desorption solution with a mass ratio of WO3/Mo = 27 can be obtained

Jan 1, 2014

By John Snowberger III, J. Brent Hiskey

The electrochemical dissolution of super alloys containing different amounts of rhenium was investigated. The initial part of the investigation focused on the anodic dissolution of rhenium from second-generation (3% Re) and third-generation (6% Re) nickel based alloys. Exploratory electrochemical tests were conducted to evaluate solution chemistries and to establish fundamental dissolution behavior of the alloys. These included rotating disc electrode (RDE) cyclic voltammetry, linear sweep voltammetry, and chronoamperometry tests. Electrolytes comprising sulfuric acid, hydrochloric acid, and ammonium sulfate were examined. Of these, a 0.1 M HCl solution proved to be extremely effective for electrochemical dissolution of samples of CMSX-4, CMSX-10, and SC-180 alloys. This paper discusses in detail the electrochemical behavior of these alloys.

Jan 1, 2014

By Marilia S. de Magalhaes

Keywords: sinter, characterization, agglomeration, iron ore Iron ore sinters are the main burden of blast furnaces for pig iron production. The evaluation of these agglomerates is very important due to their properties affect indirectly the productivity and costs of production of the steel industry. In the sintering plants, the standard procedure of sinter assessment has been carried out by particle size control, bulk chemical analyses, tumbler and/or shatter tests and determination of reduction degradation and reducibility indexes. Microscopy techniques have just been applied to characterize sinters produced in pilot conditions, however, these techniques, the classical ones and the less traditional, allow enhancing the industrial sintering process assessment. For investigation of the phases, microstructures and fabric, reflected-light and scanning electron microscopy(backscattered electrons images) were used; for micro analytical chemical examination, energy-dispersive X-ray spectrometry; for Kikuchi patterns registers, electron backscattering diffraction. In addition to the microscopy techniques, the magnetic behavior was depicted by means of magnetic susceptibility measurements. Iron ore sinters are made up by hematite, magnetite, silicoferrite of calcium and aluminium and silicates. These phases develop either during sintering or, in some proportion, represent remnants of ores and fluxes; this is the case of some hematite and Mg-bearing silicate, respectively. From the magnetic susceptibility results, three different behaviors were determined, which are directly related to the magnetiteproportion in the samples. The phase association and proportion, the sintering conditions andthe quality assessment are some features appraised by such procedures, which reveal themagnitude of this proposal in sintering plants.

Jan 1, 2005

By Florian Kongoli

New operating conditions and process parameters are often necessary in today&apos;s industrial practice of non-ferrous smelting and converting in order to accommodate various new chemical compositions of mineral charges and environmental requirements or to conceive new and more efficient industrial technologies. An important parameter in non-ferrous smelting and converting is the liquidus surface of multicomponent slags. This surface is affected by multiple factors such as temperature, gaseous potentials, the content of each component in the slag, etc., and cannot be quantified by the existing ternary liquidus diagrams. In this work a new type of representation of the liquidus surface of multi component systems has been presented by means of a thermodynamic model. This representation waives the need of the multidimensional representation of multi component systems and yields practical two-dimensional diagrams, which can be easily used in the industrial practice.

Jan 1, 2000

By L. M. . Chia

The successful treatment of waste materials to recover metals with acceptable purity is often hampered by the presence of undesirable impurities. The problem is further complicated by the need to insure that any residues or solutions generated are environmentally acceptable. Hydrometallurgical processes involving leaching- solvent extraction-electrowinning offer some attractive features which address many of these problems. However, in certain instances trace impurities that contaminate the organics are difficult to chemically strip and interfere with the overall process efficiency. A new processing scheme has been developed which appears to provide some attractive alternatives for impurity removal from organics. It has been shown that many ionic impurities can be electrochemically removed from the organic by spontaneous direct reduction using solid metals. A variety of metal ion impurities have been removed from selected common organic extractants such as D2EHPA and TBP using different metals as the reducing agents. The results and probable mechanisms involved in the reactions are discussed.

Jan 1, 1994

By Amy Anderson

The Silica (SME) Technology has been utilized on three separate projects focusing upon the stabilization of mercury-contaminated materials: at the Mother Lode Mine in Oregon, the Sulfur Bank Mercury Mine in California and at a former chloralkali plant in British Columbia. Each of the projects relied primarily on the results collected via EPA Method 1311 TCLP, with additional tests such as SPLP, humidity cell tests and other supporting tests employed as well. Both technical and economic performance of the silica-based technology was evaluated as well as that of competing technologies in some cases. Results established that in each of the three projects an SME chemical dosage rate of 3% chemical by weight of soil/sludge was the optimal ratio required to achieve project treatment objectives, TCLP test results exhibited a reduction in the leachable mercury from the treated materials ranging between 75% and 99% as compared to untreated material, satisfying the technical objectives for each project, Project costs ranged from $l5.00 - $18.26 per metric ton.

Jan 1, 2003

By Jana Dobrovska

The paper deals with new approach for measurement and evaluation of chemical microheterogeneity of elements in polycomponent metallic systems (i. e. steels, Ni-alloys). The method is based on the original mathematical model for determination of distribution curves of dendritic segregation of selected elements and on the original mathematical model for determination of the effective partition coefficients of these elements in the structure of analyzed alloy. Application of the method at research of chemical heterogeneity of continuously cast steel slab is also presented. The original results of measurement of dendritic microheterogeneity of eight elements (Al, Si, P, S, Ti, Cr, Mn and Fe) in structure of nine zones of a transversal section of slab are given.

Jan 1, 2006

By Youze Xu

The effect of oxalic acid, acetic acid, citric acid and EDTA on extraction of Cr (?) in soils contaminated by chromium- containing slag was investigated using a batch of incubation experiment. The results show that the pH value decreases more obvious with the increase of the amount of organic acid. The amount of Cr (?) extracted increases with increasing the amount of organic acid. When the ratio of organic acids to total Cr was 5:1, citric acid revealed the highest extraction effectiveness, followed by EDTA, oxalic acid and acetic acid, respectively. The amounts of Cr(?) extracted by citric acid, EDTA, oxalic acid and acetic acid increased by 439%, 244%, 215% and 162%.

Jan 1, 2009

By Isrun Bohlinger

Resources recovery of brasses for semifinished products often results in the formation of hard spots impairing the quality of following abrasive and/or surface finishing processes. A short survey is given on the recycling processes, followed by the actual knowlegde of genesis, composition, and possibilities of avoidance of hard spots. Informations on genesis and composition of hard spots are completed by data from recent experiments.

Jan 1, 1998

By John A. Clark, Danylo Oryshchyn, Casey Carney, Stephen Gerdemann, Cathy Summers, Thomas Ochs

"Limited analysis of combustion gas streams where carbon capture is not of interest is done mainly to ascertain operation parameters. Stringent regulations on acid gases and particulates promote careful flue gas analysis. Unregulated components are typically not analyzed. Typically not more than four points (two in the boiler, and one each in the flue and the stack) are sampled. A successful oxy-fuel process with carbon capture and compression is anticipated to require as many as 12 sample points with analysis for water, nitrogen, oxygen, argon, NOx, SOx, and carbon monoxide. Carbon dioxide captured for beverages produces a high value product and the cost associated with analysis is warranted. However, carbon capture for disposal must keep all costs to a minimum. This paper will compare alternative approaches for cost-effective sampling and analysis of the carbon dioxide product streams from oxy-fuel combustion, through all stages of production through compression and pipeline/vessel delivery.IntroductionAnalysis of gases in an oxy-combustion process with carbon capture is essential to the operations of the oxy-fired boiler and the subsequent collection, compression, and purification of carbon dioxide. The process is charged with pure oxygen and not-so-pure carbon in the form of coal at the front end, generating a product of mainly carbon dioxide with traces of argon, nitrogen, sulfur compounds, nitrogen compounds, oxygen, hydrogen, and mercury. It is possible that hydrogen chloride and hydrogen sulfide may also be present in trace amounts [1]. The trace components primarily come from impurities contained in coal such as water, sulfur, nitrogen, and volatile organic compounds. Coal also contains a good deal of mineral matter that is transformed into ash during combustion, becoming particulates that can complicate the analysis regimes utilizing standard analytical equipment."

Jan 1, 2010

By Liyuan Chai, Qin Liu, Bing Peng, Jia Wang, Qiang Zhang

"Electrolytic Manganese Residue (EMR) was used as the main material to prepare cementing material activator for the utilization of the residue from electrolytic manganese dioxide (EMD) or electrolytic metallic manganese (EMM) production. The effects of chemical activation, thermal activation and mechanical activation on retarding activity and excitation activity of EMR were investigated according to the setting time and activity index of EMR-slag cementing material. The results showed that the EMR exhibited good activating performance after being ball-milled for 18 min and then treated for 1-2 hours at temperature range of 350-450 ?. The optimal properties of cementing material activator were achieved at the weight percent ratio 30 : 3 : 5 of EMR/Ca(OH)2/cement clinker.IntroductionMany hazardous industrial solid wastes such as blast furnace slag, fly ash, steelmaking slag, chromic slag and electrolytic manganese residue [1] are generated n China and their amounts increases every year. The accumulation of the solid wastes during past years is very huge and they could be hardly recycled effectively as a sustainable resource. 2.35 billion tons of industrial solid wastes have been produced up to now [2]. It is estimated that they would exceed 3.3 billion tons by the end of 2015 [3]. On the other hand, the quick development of Chinese infrastructural construction needs more cementing materials. The production of traditional building materials consumes lots of natural resource such as clay and limestone and discharges at least 1 ton CO2 and other pollutants per ton clinker [4]. Therefore, it is necessary to develop new types of cementing materials instead of clinker [5,6]."

Jan 1, 2012

By J. T. I. Poijärvi

Outokumpu Harjavalta Metals Oy operates copper and nickel smelters, three sulphuric acid plants and nickel refinery at Harjavalta and copper refinery and precious metal plant at Pori. The by-products of these plants are presented in this paper. The by-products of the smelters include products from slag cleaning of flash smelting furnaces and converters, flue dusts and smelter off-gases. Weak acid and sludges from cleaning of smelter off-gases and acids are the by-products of the acid plants. The by-products out of the copper refinery are crystallized metal sulphates and sludges from electrolyte purification, on which a co-production process of the copper tankhouse is based. The main by-products of the precious metals plant are products from anode slime treatment and platinum metal group concentrates in the recovery of precious metals. Sludges from nickel matte leaching and precipitates from solution purification are the by-products of the nickel refinery. The formation, treatment and processing as well as the research work done for the utilization instead of dumping of the by-products in the production of copper and nickel will also be discussed in this paper.

Jan 1, 1995

By Qiang Zhang

Hybrid composites are fabricated by adding two reinforcements into matrix materials so that the expected excellent properties can be achieved through the combined advantages of short fibers, and different size particles (micron or submicron), which provide a high degree of design freedom. In this paper, hybrid preforms were produced with the different size reinforcement of the Al2O3 particles and short fibers. The Al-Si alloy-based hybrid composites were fabricated by preform-squeezing casting route. The structure and performance of composite materials were studied with the Transmission Electron Microscopy (TEM), and Scanning Electron Microscopy (SEM). The results show that the reinforcements, both particles and fibers, distribute homogeneously in the matrix materials, and the properties of composites are found to improve in comparison with the matrix Al-Si alloy.

Jan 1, 2009

By J. R. Kiji

The Cerro Matoso S.A. mine and smelter, in the Cordoba lowlands of northwestern Colombia, consist of a dedicated laterite nickel mine, ore blending, drying and an RKEF process to produce high-quality ferronickel. At a project investment of $400M, first production of ferronickel was in September 1982, and in its inaugural year CMSA produced 6,150 tons of contained Ni from a mined ore grade of 3.2% Ni. Initial operational difficulties resulted in a number of furnace run-outs, which impacted ramp up to design ore throughput of 128 dry t/h Since then CMSA has steadily incorporated process improvements and initiatives to take the single line operation to an ore throughput of 175 dry t/h. A second 175 dry t/h line was added in 2001 (investment of US$ 300M) to consolidate CMSA as one of the world&apos;s lowest cost Ni producers with an installed annual production capacity of 50-55,000 tons Ni. The most recent addition is commissioning of Phase I of an ore-upgrading project to counteract the effect of declining ore grades. Keywords: Laterite, ferronickel, pyrometallurgy, smelter.

Jan 1, 2004

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976

By A. W. Worcester

The plant is designed to produce 60,000+ tons of refined lead per year from a nominal feed consisting of 110,000 tons of SLI and industrial batteries, and 10,000 tons of lead contained in drosses and scrap. The plant will also produce as by-products polypropylene chips and detergent grade sodium sulfate, using the Engitec Impianti CX Technology. The battery separation circuit will consist of a battery breaking hammermill and a vibrating screen with water sprays to separate the battery paste from the grid metal and other battery components. The battery components, consisting of ebonite, and separator materials, will be separated&apos; from the grid metal and classified with the use of hydrodynamic water separators. The battery paste will be treated with sodium carbonate to produce a lead carbonate paste for smelting in a reverberatory furnace. The slag from the reverberatory furnace will be campaigned through a traditional primary blast furnace to produce hard lead. The sodium sulfate liquor from the lead carbonate filtration step will be crystallized to produce anhydrous sodium sulfate. The metallic grid metal will be treated through a small rotary smelter of the Engitec design to produce a hard antimonial lead. The plant&apos;s scheduled to be commissioned 12 months after receipt of all of the Federal and state permits. The plant will be integrated into the Buick Primary Lead Smelter, located in the center of Missouri&apos;s New Lead Belt, at Boss, Missouri. This will allow The Doe Run company to fully utilize all of its existing assets.

Jan 1, 1990

By Hui Wang

With the great increasing use of nickel metal hydride batteries recently, the waste of this kind batteries have been paid for close consideration. For the main reason that the waste of the batteries contained precious metals and lanthanide which cost great lose. This paper introduces the pyrometallurgical process of recovering nickel and cobalt from the waste of the nickel metal hydride batteries. Particularly, the waste for the process was from factory during the producing program. The use of designed solvent to divide nickel and cobalt in melted state from the waste is described. Also, the result of the nickel and cobalt and melted gangue that mainly consist of lanthanide oxide are included in details. The aim of the paper is to find out a simple and feasible way to reuse waste from nickel metal hydride batteries.

Jan 1, 2009

By Jeremy Gregory

The disposal of end-of-life electronics is an issue receiving increasing scrutiny. This paper evaluates several alternatives for recycling cathode ray tubes (CRTs) within monitors and televisions. The primary recycling options for the glass, reuse in new CRTs or as a smelter flux, are examined from economic and environmental standpoints. The economics are modeled using a cost model that includes dependencies on processing costs, transportation logistics, and incoming material composition. The environmental consequences are modeled using life cycle assessment methodologies to determine the energy embodied in each processing alternative. Results map out preferred processing alternatives across a range of technological and operational conditions. The results indicate that economic costs and environmental consequences are heavily impacted by transportation. The preferred destination of CRT glass for a recycler is highly dependent on the proximity of the consumer to the recycler, although it is generally economically advantageous for the recycler to extensively dismantle the CRTs.

Jan 1, 2006