Search Documents

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By Ximeng Zhu

The electrochemical behavior of mineral and coal pyrites in stirred and quiescent alkaline boratelsulfate solutions @H 7.9-10.5) have been investigated using cyclic voltammetry. Significant differences in the electrochemical response of these pyrites were observed. At the mineral pyrite surface, three anodic peaks at about -0.8 V, -0.1 V and +0.5 V (SCE) have been detected along with their corresponding reduction peaks. The first two peaks correspond to FeIFeOI) and FeOI)lFe(III) oxidation. The third peak is present for quiescent conditions but disappears as a distinct peak when the electrolyte is stirred. In the upper voltage region +0.30V (SCE), the current increases markedly during stirring and the reactions correspond to the oxidation of pyrite with the formation FeOII) oxides plus elemental sulfur. Also there is evidence that Fe oxy-ions form. Coal pyrites, under rapid sweep conditions display only the first two anodic peaks, the associated reduction peaks and an additional reduction peak corresponding to one or more of the high voltage oxidation products. After prolonged exposure to high potentials, coal pyrite displays reactions similar to those of mineral pyrite but at much higher current densities demonstrating the much higher reactivity of the coal pyrite. The reactivity sequence was Upper Freeport coal pyrite > Pittsburgh coal pyrite > mineral pyrite.

Jan 1, 1991

By David N. Hanlon

The effect of high-temperature plastic deformation of the austenitic phase (y) on the subsequent phase transformation to ferrite (a) has been experimentally investigated, and modelled using a physically-based model. The effect is of importance for steel sheet, in view of me significance of the phase transformation with respect to the eventual properties of the material. In this paper the kinetics of the y ? a phase transformation has been studied after different degrees of prior deformation. The degree of deformation is varied by applying different deformation temperatures and strain rates, and by allowing a varying extent of recovery and recrystallisation. Consequently, both dynamic and static recovery and recrystallisation have been involved. The dilatometric observations on the phase transformation have been modelled using an interface-mobility model, in which the effect of the dislocation structure is introduced as an additional driving-force term. The effect of the stored energy on the nucleation process, which appears to be affected more strongly than the growth of ferrite, is examined in terms of the classical nucleation theory.

Jan 1, 2001

By K. S. Raja, M. Misra, S. K. Mohapatra

"Ordered arrays of TiO2 nanotubular photocatalysts were prepared by a simple anodization process. Band gap states of the TiO2 were altered by controlling the anodization electrolyte composition and thermal annealing conditions that resulted in enhanced photo activity. These nanotubes were used for reducing CO2 to methanol either by photochemical or photo electrochemical routes. Pd nano-particle loaded TiO2 nanotubes were employed for photochemical reduction of CO2 to methanol that showed a conversion rate of 12 x 10-3 mol m- 2h-1. Carbon modified TiO2-xCx type nanotubes were used as photo anode and Ti as cathode for photo electrochemical reduction of CO2. The potential of Ti cathode was maintained at -0.5 V SCE. The formation rate of methanol was determined as 13 x 10-3 mol.m-2h-1.1. IntroductionGlobal warming due to emission of carbon dioxide is a serious environmental concern. The atmospheric concentration of CO2 is about 384 ppm by volume and about 3 x 1012 tonnes by weight. Burning of fossil fuels and deforestation are the leading causes for increase in the anthropogenic CO2. More than 32 x 109 tonnes of CO2 are released per year (based on 2006 data) worldwide from the fossil fuel. Pumping CO2 from the fossil fuel power plants into deep ocean basin is one of the most discussed disposal options. The other potential option is converting this green house gas into valuable fuels.Carbon dioxide feed stock can be converted into fuels of solid, liquid or gas phase by chemical, electrolytic, photocatalytic and photo-electrocatalytic methods. Reduction of CO2 to fuel form of any phase requires energy. The reduction process should be energy efficient so that we do not spend more energy and emit more (indirect) CO2 in the process of converting CO2. From this point of view, conversion processes occurring at room temperature look attractive.Electrolytic conversion of CO2 into various forms such as methane1, ethane2, ethylene3, methanol4,5, ethanol6, n-propanol, formic acid7, and formaldehyde has been widely reported. The standard equilibrium potential (at pH: 0) for reduction of CO2 to methanol is 0.14 VSHE and to methane is 0.2 VSHE which is thermodynamically more favorable than hydrogen reduction. However, the gas phase reduction is kinetically complex requiring effective electrocatalyst. The major issues with electrolytic conversion of CO2 to useful products are:"

Jan 1, 2010

By Aiyuan Ma, Tu Hu, Chenyu Sun, Yonggang Zuo, Hongying Xia, Jinhui Peng, Libo Zhang, Yongguang Luo

"In this study, the adsorption characteristics of tannin acid in aqueous solution were investigated using regenerated activated carbon (AC), with the aim to remove the tannin acid organic matter from the solution after zinc hydrometallurgy and Ge precipitation. Results showed the temperature has little effect on the adsorption ability (q.) of the regenerated activated carbon. The experimental equilibrium data were tested for the Langmuir and Freundlich isotherms. The adsorption equilibrium was better described by the Langmuir isotherm (R2 > 0.99). Pseudo first- and second-order kinetic models were used for describing kinetic data. It was determined that the kinetics of tannin acid removal was well fitted by second-order reaction.IntroductionGermanium recovery is a complex processes [1]. Hydrometallurgical processes are favoured and these are based on the precipitation of germanium as hydroxide or sulphide or alternately with tannic acid [2]. However, in the germanium recovery process, too much tannin is consumed by the germanium-tannins complexation process, and results in a high content of tannic acid remaining in solution, which is harmful to the valuable metal recovery [3]."

Jan 1, 2014

By Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide (CO2), a major component of the greenhouse gases, could be comprehensive utilized as a valuable resource to oxidize vanadium during the converter vanadium extraction process. The thermodynamic software, FactSage, was utilized to study the oxidation ability and theoretical cooling ability of using weak oxidant CO2 as coolant in vanadium-containing hot metal. Besides, experimental research on vanadium extraction in CO2 and O2 mixed blowing extracting process had been undertaken. The results indicated that the elements C, Si, V, Mn etc. could be oxidized by weak oxidant CO2, and the content of V2O3 in slag was approached to pure O2 blowing. Furthermore, CO2 had a remarkable cooling ability and the molten bath temperature kept on decreasing as CO2 blowing rate increases. This research has proved that CO2 and O2 mixed blowing in vanadium extraction process are effective.

Jan 1, 2015

By J. H. Ahn, J. K. Yoon, Jung-Eui Lee

"A concentration change during grade transition operation in steel thin slab casting is predicted with computer simulation, water model and plant trial. Fluid flow and mixing patterns in various tundish levels and flow rates were analyzed through three-dimensional mathematical modeling. Comparing with water model experiments, a simple, efficient and accurate computational model has been suggested to predict the concentration profile at outlet of tundish. Based on the model, mixing in/below the mold was analyzed considering EMBR. The predicted concentration profiles show good agreements with the measured values. It is found that the lower vortices in the mold are suppressed by the electromagnetic field and the plug-like flow region develops which decreases the intermixing of two different grades of steel and shortens the length of transition region.1. IntroductionContinuous casting is the primary mode of production of semifinished steel products as it offers tremendous advantages in terms of energy savings, increased yield and higher productivity over the traditional ingot casting process. Efforts have to be made constantly to improve the quality of the cast product, reduce costs and thus increase the competitiveness of the steel manufacturer. One way of reducing costs is to reduce the amount of intermixed steel during the grade transition operation.Several different procedures exist to handle the casting of dissimilar grades for the conventional slab casting. Each procedure has its own merits and demerits. In order to choose the best method for a particular operation, there are a lot of researches. In the case of present continuous thin slab casting of POSCO mini mill, the only possible method is to change ladle during the grade transition. Due to the high casting speed (3.8m/min-4.4m/min) it is impossible to change the tundish and due to the thin thickness of slab it is also impossible to insert grade separator."

Jan 1, 2000

By Dao Su, Kelang Mu, Yufeng Guo, Jinghua Zeng, Tao Jiang

"The influence of high pressure roller grinding (HPRG) on sintering of iron concentrate fines was investigated. Results of mini-sintering tests showed that assimilation temperature of iron concentrate fines decreased from 1230 ? to 1220 ? and assimilation time was shortened from 10 min to 5 min when the iron concentrate fines was pretreated by HPRG. Sinter pot tests showed that the yield of sinter increased from 60.33% to 72.92% , tumble index increased from 44.35% to 46.66%. The investigation indicated that, after being pretreated by HPRG, iron concentrate fines are improved in ballability and the fraction of fine particles increased, resulting in the improvement of granulation property and reactiveness in solid state reaction. As a result, sintering of iron concentrate fines were strengthened.IntroductionWith the rapid development of iron and steel industry and the decrease of high-grade ores, the imports of iron ore are increasing continually. It is of immensely strategic importance for development of iron and steel industry and energy security in our country to make good use of iron concentrate fine which is low price, high grade and has a refractory sintering property. When iron concentrate fine is used in sintering, granulation property of sinter mixture and permeability of sinter bed get poor. As a result, yield and quality of sinter fall down. Many researches show that, when HPRG is used in pelletization, quality of pellets is improved dramatically. Meanwhile, HPRG has a low energy consume, a large handing capacity and it is benefit for environment protect. At this theme, strengthening of sintering of iron concentrate fine pretreated by HPRG was investigated in this paper."

Jan 1, 2012

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate. The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refming times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using C02 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

Microstructural investigation has shown that grain splitting or deformation banding ( DB ) develops progressively with increasing strains during cold rolling. Of particular significance to simulating texture development in cold rolled BCC polycrystals is the operation of higher order slip systems other than 110 and, the occurrence of DB in the rolling plane since the latter allows a new relaxation of the shears. Deformation banding ( DB ) model includes grain subdivision in the rolling plane and applies the Relaxed Constraints ( RC ) mechanism for the other shears. An energy criterion for deciding whether deformation banding occurs or not has been postulated, referred to as Deformation Banding Criterion ( DBC ). This paper reports the results of the investigations into the effects of different slip systems, i.e., those based on 110, 112 and 123 slip planes and their combinations using RC, DB and DBC models, in developing simulated BCC rolling textures.

Jan 1, 1999

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FeAsyO2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS2O3 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By Takeshi Nagano

Copper pyrometallurgy in Japan has experienced quite fundamental changes in last fifteen years. The severe environmental restriction coupled with increase of energy costs accelerated the development work of the new continuous process in Mitsubishi Metal Corporation. After several years of pilot plant test work the commercial plant was put into operation at Naoshima Smelter in 1974, the design capacity of which was 4,000 tonnes of copper per month. Many modifications and improvements have been incorporated into the process and 7,200 tonnes per month of copper production was achieved in 1983, proving that continuous process was much more economical than conventional process. It is now possible to design and operate the continuous process in wide range of capacity. This paper will review the process and describe the progress of the process in these 10 years. 311

Jan 1, 1985

By Chuanhong Li, Zuohua Lin, Zhancheng Guo

"Catalytic mechanism of CeO2 in combustion of coals was investigated in this paper. Catalytic combustion of four kinds of coals with different metamorphic grades by CeO2 was examined, suggesting that catalytic function of CeO2 increases with increase of metamorphic grade of the coals. One important reason for CeO2 promoting combustion of the coals is that pyrolysis of anthracite is advanced by CeO2, which not only raises the pyrolysis rate and pyrolysis conversion ratio, but increases contents of light components in pyrolysis gas; and both pore space and specific surface area of the pyrolysis char are enlarged by CeO2, which is another reason. In order to realize in situ catalysis for reducing catalyst consumption, it is crucial to increase catalyst particle number and enhance the bonding force between catalyst and coal. In addition, remarkable energy saving effect was observed when a nanometer calcium-based rare earth catalyst obtained by hydro-thermal synthesis was applied to catalytic combustion of coal injection into blast furnace.Introduction Coal combustion is acknowledged as one of the most important coal applications. Since addition of catalysts could reduce the ignition temperature of pulverized coal and accelerate the coal combustion, catalytic combustion is generally accepted as an effective measure to realize fast combustion of coal. Furthermore, different catalysts added may produce different effects on ignition temperature of coal. It is reported activity of catalysts with the same cation follows this order: OH->CO3 2->Cl->SO4 2-; while that of the catalysts which have the same anion follows: Cs+>Rb+>K+>Na+>Ba2+>Li+>Sr2+>Ca2+>Mg2+>Be2+ [1-4] .Due to the special physical and chemical structure, CeO2 plays an important role in the catalysis field. Many literatures point out that CeO2 not only has great catalytic effect on energy conversion, succeeded in catalyzing combustion of gaseous fuels such as CH4, CO, etc. but also can catalyze combustion of some liquid and solid fuels such as JP-10, black carbon, carbon deposit in the automobile exhausts and so on [5-9].Pyrolysis, the first step of combustion, directly influences ignition temperature and combustion rate of coals. So a great variety of catalysts were applied to catalyze pyrolysis of coals. And plenty of studies suggest that the alkali and alkaline-earth metal compounds inherent in the coals show apparent catalytic effect on coal pyrolysis. Meanwhile, addition of alkali and alkaline-earth metals into coal combustion process also indicates obvious catalysis effect, accelerating coal pyrolysis, improving pyrolysis conversion ratio, increasing contents of pyrolysis gases and changing composition of the pyrolysis gases [10-15].Although alkali and alkaline-earth metal compounds have good catalysis effect on coal combustion, their application in the catalysis field was limited because of their erosive attack to the combustion equipments. In contrast, CeO2, as a substitution of the traditional coal catalysts, presents widely potential application due to its good catalysis ability, non-corrosive and nontoxic. However, investigation on CeO2 catalyzing coal combustion is rarely reported. In this work, catalytic mechanism of CeO2 in coal combustion was studied, in an attempt to provide theoretical foundation for developing new catalysis technologies."

Jan 1, 2009

By M. D. Strachan

Technical & Procurement Services Limited (TECHPRO) in Ashford, Kent, UK, have been appointed as Project Managers for the major rehabilitation of the Copper Smelting complex of Nkana Division, Zambia Consolidated Copper Mines Limited, (ZCCM) Zambia. In outline, the overall scope covers three main areas: a) Transfer and implementation of new technology into Zambia for the production of primary copper. b) Replacement of gas collection and gas treatment circuits to guarantee high quality feed to the acid plants. c) Completion of a number of minor projects in the copper smelter and associated utility plants to complement changes in the primary smelting technique. This paper describes the Project Management methodology and style used by TECHPRO to tackle typical problems that arise in retrofit projects of this type. Reference is made specific aspects of the smelter projects to illustrate solutions to the problems. The subjects. addressed highlight the complexities not only of having a -Client 5,000 miles from the Project Office, but also the difficulty of co-ordinating and controlling the performance of min sub-contractors who are also geographically distant.

Jan 1, 1991

By X. Jay Gao

A fast high-temperature carburizing process integrated with materials design and optimization via a systems design approach was developed to significantly reduce process cycle time. Process experiments were focused on boost cycles to obtain a robust boost process and investigate surface reaction kinetics, primary carbide formation and dissolution. Weight gain and microhardness were measured, all showing evidence of non-monotonic time evolution for longer boost times at higher temperatures. Optical and electron microscopy and other techniques have been used to identify possible carbides, their location and types. These results assist the picking of first boost time with least variation rate in terms of content of case carbon and carbides, dissolvable in subsequent diffuse if any. The results also provide critical information to properly formulate surface reaction kinetics and diffusion and formation kinetics of carbides modeled using DICTRA. Keywords: high temperature vacuum carburizing, partial pressure carburizing, heat treatment, process development, carbide, case hardening, microstructural analysis, over carburizing

Jan 1, 2003

By Liow Jong-Leng

A survey of the interactions of large gas bubbles formed from top and bottom injection of gases into melts was carried out. Spherical cap bubbles were found not to produce much splash when they break through the bath free surface except for that formed by plunging of the-spout at its edges. In contrast, the bursting of balloons produces cavities which give rise to liquid jets being ejected from the bath free surface. The position of the balloons relative to the bath free surface is an important parameter in the formation of the liquid jet. It is found that the interactions of multiple bubbles close to the free surface is important in determining the splash behaviour of gas injected systems.

Jan 1, 1996

By Takaaki Shibata

The Tamano Refinery has developed two new processes for removing the impurities, arsenic, antimony, and bismuth from an electrolyte. The first process involves bleeding the surface electrolyte in the electro-refining cells. The copper concentration level in the outermost layer is lower than that in any of the other layers, while the impurity levels are almost the same in all layers. Bleeding the surface electrolyte increases the amount of impurities removed in the liberator by approximately 20%. The second process involves adsorbing antimony and bismuth from the electrolyte by means of chelating resin. As the electrolyte passes through the packed column of chelating resin, antimony and bismuth are selectively adsorbed. They are then desorbed by means of hydrochloric acid, and then recovered in the form of a highly concentrated antimony chloride solution by means of evaporation. This process almost doubles the capacity for removing antimony from an electrolyte.

Jan 1, 1987

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3 PbZrO3-Pb(Mgl/3Nb2/3)O3 system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densification by the normal sintering was slow even at high temperatures, When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.-

Jan 1, 2003

By Hirofumi Tai, Masafumi Morishita, Toshiya Miyake

"In order to prevent corner cracks on cast steel slab and bloom, solidification delay at the corners should be controlled at the proper level. For this purpose, controlling the heat flux from the molten steel to the solidified shell at corners is essential. In this paper, optimization of the submerged nozzle was studied based on flow and solidification analysis.First, for the slab caster, the submerged nozzle shape was optimized. The improved nozzle was tested in actual casting and completely succeeded in preventing corner cracks. It was clearly demonstrated that the solidification delay and the corner cracks were strongly affected by the spouting stream from the submerged nozzle.For the bloom caster, on the other hand, the setting angle of the nozzle was optimized. Numerical simulations demonstrated that the spouting stream from the nozzle causes solidification delay, impinging at the corners under electromagnetic stirring conditions. Optimization of the setting angle of the nozzle is a possible means to reduce the solidification delay at the corners for the bloom caster.Related to the numerical analysis of flow and solidification, the effect of the critical solid fraction at the tip of the dendrite structure on the solidification under electromagnetic stirring conditions was studied."

Jan 1, 1999