Search Documents

By Alan Bugden

Goedehoop Colliery produces 8 million tonnes of coal a year, principally from room and pillar mining, and is situated in the Witbank Coalfield in the Republic of South Africa. The mine has a long and successful record of producing export quality coal from the 2,4 and 5 seams at depths ranging from 20 to 100 metres using modem mining equipment. Following a number of fatalities caused by large and unexplained roof falls in roadways and intersections of supported ground, a review of the roof control system at Goedehoop was carried out. This led in turn to a programme of underground measurements and surveys. This included detailed investigation of the roof falls, horizontal stress mapping, stress measurement and short encapsulation pull testing on roofbolts. These investigations led to a number of important conclusions in relation to the state of stress in the ground, the roof failure mechanisms, standard of rootbolt installation and performance of the roofbolt system. As a result of the work Goedehoop Colliery has made a number of substantive changes to the roof control management system at the mine. These include: 1. A recognition of the importance of horizontal stress as the main factor responsible for roof falls. 2 The forward planning of roof support based on known features which cause the stresses to be elevated. 3. The introduction of a more effective roofbolt system, which can be more easily installed to a high standard. 4. A response system based on risk assessment and monitoring roof movement on a routine basis. The paper describes the knowledge acquired, the conclusions drawn, the changes made and progress to date.

Jan 1, 2001

By Kanaan Hanna

Abandoned mines pose a serious threat to public health and safety, as well as the environment. When active workings approach old mine workings, miners could encounter significant hazards. Additionally, the presence of mined-out areas or voids underlying residential/commercial properties, transportation, and infrastructure systems can cause subsidence issues ranging from differential settlements and sinkholes to catastrophic collapse. All these features can result in adverse impacts in terms of cost and public safety. Traditionally, mine void detection and related engineering investigations for mine subsidence risk assessment and mitigation have been greatly dependent on systematic drilling and grouting backfill programs. The unknown location and condition of abandoned underground mines represent significant challenges to geologists and engineers in accurately evaluating subsidence hazards and developing appropriate mitigation measures. A comprehensive, multi-phase mine subsidence investigation was conducted at an abandoned western U.S. mine site. The mine operated in an approximately 8-ft (2.4-m) -thick coal seam using room-and-pillar extraction from 1919 to 1922. The mine lies at depths ranging from 50 to 100 ft (15 to 30 m), and it is overlain by critical pipeline and utility corridors. Any future subsidence/ sinkhole that occurs beneath or adjacent to the corridors could pose a significant threat, specifically to the structural integrity of the pipeline corridor. Therefore, the engineering geophysical investigation was initiated to determine the potential subsidence risk. This paper describes a recent success achieved by using integrated engineering geophysics in subsidence risk evaluation. A summary of significant results with emphasis on subsurface characterization, mine workings and voids delineation, modeling analysis, and high risk zones identification and mitigation strategy is presented.

Jan 1, 2011

By Anthony Lannacchione

There has been a persistent need to forecast roof falls so that miner's exposure to hazardous underground environments can be minimized. Several monitoring techniques have been developed and are used today with varying levels of acceptance in the mining industry. This paper examines the potential for monitoring microseismic emissions activity as a means of forecasting roof falls. The use of this activity to forecast roof falls has drawn only limited attention, resulting in a lack of published field performance data. This deficiency is being partially addressed by analyzing data obtained during longwall mining at Moonee Colliery in 1998. The Moonee data base contains a wealth of information concerning roof fall forecast parameters and the seismic alarm criteria used to develop these forecasts. Four seismic alarm criteria were developed and used by Moonee with varying degrees of success. Roof falls were forecasted 73% of the time with average forecast times of 54 minutes. Ninety percent of the predicted roof falls had a warning time, i.e., the time between warning and roof fall event, of greater than 1 minute. The fraction of forecasted roof falls decayed logarithmically as a function of warning time, until only 20% of events were predicted more than 100 minutes prior to roof falls. False alarms occurred in 50% of the warnings. Many of the false alarms were quickly followed by a cessation in mining which could have temporarily halted the on-going failure process. If mining had continued immediately after the false alarms, a roof fall may have occurred soon after. The microseismic activity collected .from Moonee Colliery demonstrates that techniques to forecast roof rock instabilities in underground mines are possible.

Jan 1, 2005

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms in strata around a longwall gate road system at two sites in an underground coal mine near Ham, WY. Of particular interest was timedependent (on the order of several months) roof deformation. Strata above and below the coal seam are very weak, carbonaceous mudstones that have cohesionless planes of weakness oriented along bedding, which dips approximately 8° to 16° at N 49° E. An extensive array of instrumented roof bolts, roof extensometers, and biaxial stressmeters were installed during development mining at these two sites under variable depth of cover [I83 to 335 m (600 to 1,100 ft)], seam dip (10° to 16°), and top coal thickness [estimated to be 0.30 to 0.61 m (1 to 2 ft) on the downdip side of the entry]. Bolt load and roof deformation histories during the entry development periods were compared. Bolt loads at site 2 were less than those at site 1, which is consistent with the amount of overburden. Deformation magnitudes at site 2 were similar to those at site 1, but deformation rates were approximately 44% greater and nearly constant over time, whereas the deformation rates at site 1 decreased exponentially over time. Also, most deformation occurred above the bolt horizon at site two, but extensometer measurements at site 1 showed that a significant amount of deformation occurred within the bolt horizon. The most significant factor that influenced bolt tension and timedependent strata deformation was strength and Young's modulus of the strata. Finite-difference models support this conclusion.

Jan 1, 1996

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009

By Jinwang Zhang, Zhaohui Wang, Jiachen Wang

"Thick coal seams (seam height larger than 3.5 m) account for a large portion of the proven coal reserves of China, and underground thick coal seam mining provides about 50% of the Chinese annual coal production. Such seams are mainly mined using the longwall top-coal caving (LTCC) method. For safe and successful mining, a number of analyses on the stability of surrounding rocks in the LTCC face area have been extensively performed, and certain research achievements have been made. This paper introduces the main findings on rock pressure occurrence in the LTCC face during the last few decades and presents face and roof stability control techniques. INTRODUCTIONUnderground thick coal seams in China provide 1.8 billion tons of coal every year, which accounts for approximately 50% of the total Chinese annual coal production and 25% of the world, indicating that thick coal seams stand an important position in Chinese coal mining industry (Wang, 2005). Before the 1980s, thick coal seams were mined mainly by using the multiple-slice mining method. With the improvement of mining techniques and equipment in last two decades, longwall top-coal caving (LTCC) and high-seam, single-cut longwall are employed for thick coal seam extraction, offering advantages over multiple slicing from entry excavation and production perspectives (Wang, 2013).. The primary author of this paper introduced the most popular thick coal seam mining methods in China at the 30th ICGCM (Wang, 2015). This paper presents the stability of surrounding rocks in face area and ground control techniques for mining thick coal seams. For traditional longwall faces (seam height less than 3.5 m), the well-developed VoussoirVoussoir beam theory has been successfully used to analyze the movement of overlaying strata, which indicates that ground control techniques have become mature for this mining system. In such faces, the four-leg support with loading capacity of 4000–8000 kN is considered adequate for safe and successful mining. These faces normally have an annual yield of 1–2 million tons (Wang, 2007). For thick coal seams, however, the traditional support becomes inadequate and the ground control problem change to be more difficult and complex. Thus, development of large-scale mining equipment and ground control techniques for enlarged mined-out space and entries have been recognized as the most basic technical problems in mining thick coal seams."

Jan 1, 2017

By Dongfeng Yun, Zhu Liu, Wendong Cheng, Zhendong Fan, Dongfang Wang, Yuanhao Zhang

"For the purpose of studying the strata behavior due to multislicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams, the shield support pressures of the upper and lower slices of Panel 37220 in Dongxia coal mine were monitored using the KJ513 dynamic monitoring system. The set up rooms adopted the ""horizontal line-arc segmentinclined line"" form and used different types of shield supports. The results showed that the strata pressure of upper slice Panel 37220- 1 changed slightly along the strike direction, while along the dip direction it exhibited strong to weak pressure from bottom to top. The first weighting interval oflower slice Panel 37220-2 was about 60.Sm, and the average periodic weighting interval were about 22.6m. The strata behavior of Panel 37330-2 exhibited a spatiotemporal characteristic in that periodic weighting occurred first in the middle-upper part, followed by the middle and upper parts, arc segment, and finally the lower part. During the periodic weighting, the weighting interval and intensity also exhibited strong space characteristics. The average dynamic load coefficient was 1.48 and the maximum lateral pressure of the side shield was 900Kn1000kN.INTRODUCTIONThe steeply dipping coal seams account for about 20% of proven reserves and 10% of output in China (Wu, et al, 2014). About 50% of coal mines in the western China have steeply dipping seams, and are mainly distributed in Sichuan, Gansu, and Chongqing. When the steeply dipping seam employs longwall mining along the strike direction is employed, the waste rocks fill the gob nonhomogeneously along the dip direction, the deformation and caving of surrounding rocks exhibit obvious asymmetry and spatio-temporal characteristics with particular and complex strata behavior. In recent years, many research on strata behavior due to multi-slicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams have been performed with significant results (Shi, 1999; Wu, Xie, and Ren, 2010; Wu, Xie, Wang, and Ren, 2010). However, there has been a complete lack of research on monitoring the strata behavior due to multi-slicing top coal caving longwall mining in steeply dipping extra thick coal seam. Therefore, the strata behavior of multi-slicing panels 37220-1 and 37220-2 was systematically investigated in this research."

Jan 1, 2016

By Dennis R. Dolinar

Roof falls, even of supported roof, still constitute a major hazard in underground mines. However, associated with any fall or instability is a pattern of roof movement. Therefore, the National Institute for Occupational Safety and Health, Pittsburgh Research Center, has been conducting research into the development of practical extensometer systems that can be used to measure this displacement and to determine if a roof fall may occur, thus increasing miner safety. For extensometers to be used in the detection of potential roof falls in coal mines, an understanding of the movement and displacement rates that will lead to roof failure is required. Because roof falls are unpredictable, it is often very difficult to obtain this information. Therefore, in a coal mine in the lower Kittanning seam in Pennsylvania, a room widening experiment was conducted to intentionally cause a roof fall while roof movement data was collected. In this experiment, two adjacent rooms 5.5 m (18 ft) wide supported with 1.5 m (5 ft) resin-grouted bolts and instrumented with extensometers were widened to 9 m (30 ft). In one of the rooms, 3.6 m (12 ft) cable bolts were installed as supplemental support. In the room with no additional support, a roof fall occurred 72 h after the room was widened. Much of the 3 cm (1.2 in) of movement in this room resulted from the instantaneous and transient response to mining with displacement rates up to 7.6 cm/d (3 in/d) being measured. This was followed by a steady state displacement phase with a rate of 0.43 cm/d (0.17 in/d). Just 12 h before the fall, movement deeper in the roof caused the rate to accelerate to 1.1 cm/d (0.44 in/d). The roof in the room with the supplemental cable support did not fall even though the total roof deformation was over 7.6 cm (3 in). Significant roof movements and strains in the cabled room were detected to a depth of 3 m (10 ft) while maximum cable loads were over 180 kN (40,000 lbf). Essentially, the roof was in postfailure with the cables maintaining the material, while roof stability was indicated by a steady state displacement rate of only 0.025 cm/d (0.01 in/d) at the end of the test.

Jan 1, 1997

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

By E. M. Williams

The U.S. Bureau of Mines is investigating the use of in-seam seismic methods to monitor stress-induced changes in coal near the working face of longwall mines. Seismic surveys performed through a longwall panel and pillars near the face can provide valuable information on geologic anomalies, high stress regions, tailgate support performance and other conditions that could endanger miners or interrupt production. This paper describes the details of the equipment and data analysis techniques used, and the significant results obtained and their implications for ground control. Using seismic tomography, it is possible to conduct measurements on the pillar and reconstruct an image representing the internal velocity distribution. Successive measurements over several days identify changes in velocity attributable to changes in stress. Several field measurements were conducted at a western U.S. longwall mine to observe stress induced changes within the panel and pillars during mining. A permissible data acquisition system was designed to meet mine safety requirements for operation in gassy air. Certification from the Mine Safety and Health Administration (MSHA) was obtained, and this approved system was used to monitor stress changes in several pillars as the longwall face passed during first panel mining. Tomographic surveys were completed across the longwall panel to map the apparent abutment stresses ahead of mining. Velocity distributions show an increase in vertical stress across the panel from the headgate to the tailgate. Additionally. a yield zone along the face near the tailgate and the forward abutment approximately 100 feet outby the face in the tailgate side of the panel were detected. These results agree well with data obtained from other instrumentation emplaced in the panel near the tailgate. Using velocities for both compressional and shear waves, the Poisson's ratio was calculated for the panel.

Jan 1, 1994

By Carl Tom Blevins

Resin was first introduced to U. S. mines in 1971 and first produced in 1973. The original polyester roof bolt resin was very expensive and limited to a single cartridge size and a single slow gel time. Early resin applications were limited to very difficult ground conditions. Today approximately 80% of the over 100 million roof bolts installed in U.S. mines, tunnels, and construction projects employ polyester roof bolt resin. The industry has evolved from hand packing samples for trial testing to producing enough resin, if converted to a .9 inch (22.9mm) diameter cartridge, to encircle the world at the equator approximately three (3) times each year. Manufacturing and design improvements allow for a more consistent product with a wide range of applications at a price that is approximately 30% below our 1974 sales price. An inflation adjusted dollar buys six (6) times more resin in 2006 than in 1974. Modern gel times range from a few seconds to over 15 minutes. Viscosity is matched to bolt type and drilling machine characteristics. Multiple cartridge diameters and a wide range of cartridge lengths are offered by two operating companies. Resin manufacturers have also gone through a period of restructuring and change to meet the challenges of the mining industry. DuPont Fasloc has become Fasloc, Inc., a stand-alone company. Celtite became Fosroc then Minova, as it is known today. During this transformation, several manufacturers have either discontinued production or were absorbed. The industry led the development of the chemical grouting materials specifications contained in ASTM F432-95, Standard Specifications for Roof and Rock Bolts and Accessories. A history of the industry will be presented within a discussion of the evolution of the strength index, speed index, cartridge volume, class designation, and product marking requirements of ASTM F432-95.

Jan 1, 2006

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By Nicholas Chlumecky

One of the oldest mine supports in use today is timber cribbing. In many mining operations material, installation and maintenance costs for timber cribbings are substantial. Their performance characteristics also add to mining costs. During the 1970'6, the U.S. Bureau of Mines recognized many of the deficiencies of timber cribbing and very successfully initiated the development of steel-fiber- reinforced (SFR) concrete blocks. Since the early 1980's this SFR concrete cribbing has been manufactured as a high quality product which has found increasing acceptance by mine operators. The rapid acceptance of the SFR concrete block cribbing has proven that its use is eliminating many of the deficiencies of timber cribbing while providing superior load carrying capability. The use of SPR concrete blocks to build the cribbing is based on the same principle as wood. That is, stacking longitudinal, rectangular blocks in layers in a crisscross manner. The blocks are positioned at right angles to the blocks of the layer below. With this situation, the possibility of misalignment exists when the concrete blocks at the base are not placed exactly parallel or when the blocks of the base are subject to unequal settlement. Such misalignments creates localized, high stress areas which reduces the load capacity of the cribbing made from SFR concrete blocks. Recognizing the problem of misalignment, the Underground Supports Division of Commercial Shearing, Inc., conceived a circular, one-piece, steel-fiber-reinforced concrete cribbing which is being marketed under the name - Donut Cribbing. This concept eliminates the possibility of misalignment and provides 100% bearing between layers of stacked cribbing as well as other advantages. The purpose of this paper is to discuss the performance characteristics, installation speed and economical factors of each of the three cribbing types -- timber cribbing, SFR concrete block cribbing and SFR concrete Donut Cribbing.

Jan 1, 1986

By Michael Gauna

In 2010, the number of fatal rib falls in U.S. underground coal mines exceeded fatal roof falls for the first time ever. While recent trends have seen roof fall fatalities reduced by about 62% since the 1990s (from an average of 9.6 per year in the 1990s to 3.6 per year during the last five years), the incidence of rib fall fatalities has remained approximately constant (about 1.5 per year). In addition, injury incidents associated with pillar rib failure have been steady at approximately 100 per year. The persistence of rib fall injuries, underlined by the recent increase in rib fall fatalities, has led to this investigation of the coal rib failure parameters and methods available to mitigate rib failure in U.S. underground coal mines A detailed study of the 21 fatal rib fall incidents that have occurred since 1995 (excluding coal burst incidents) indicates that the two most important risk factors are the mining height and the depth of cover. The depth of cover was 700 ft (213 m) or greater in 81% of the fatalities, and the mining height was at or exceeded 7 ft (2 m) in every instance but one. Other risk factors included multiple seam interactions, rock partings in the seam, and retreat mining. The accident history reveals that joints or slickenside features within the rib increase the hazard. Approximately threequarters of the rib fatality victims were roof bolting machine operators and continuous mining machine operators. This paper includes a brief overview of techniques for rib control; including bolts, standing support, bent steel straps, and rib strapping. The available mining equipment features for installing rib support and protecting operators from rib falls are also discussed. A proactive approach to rib control using available technologies will lower the risk to miners and is an endeavor that must be pursued to reduce rib fall accidents.

Jan 1, 2011

By David P. Conover, Jake Bain, Christopher M. Ross

"Highwall mining of thick (up to 100 ft) steeply dipping (20° or more) coal seams provides many challenges, both geotechnically and operationally because seam dips near or in excess of highwall mining machine capabilities are encountered. Maximizing coal recovery while maintaining highwall stability requires innovative techniques with regard to web and barrier pillar layout, depth of penetration, and choice of mining horizon within the seam. Stability of highwall mining slopes, openings, and pillars are typically analyzed using the ARMPS-HWM program, as well as LAMODEL, UDEC, and Slope-W modeling. Highwall stability can be maintained and highwall mining production optimized by applying design criteria in creative ways, including alternating miner penetration depths and initiating mining of thick seams toward the bottom of the seam. Highwall mining of thick, steeply dipping coal requires careful planning and execution, including close cooperation between geotechnical design engineers, the mining company, and the highwall mining contractor. This paper describes the application of creative design techniques to a specific pit arrangement at the Westmoreland Kemmerer Mine, Kemmerer, Wyoming. Highwall mining was accomplished by UGM ADDCAR Systems, LLC, on a contract basis. INTRODUCTION Highwall mining is a technique for attaining additional coal recovery after the economic strip limit is reached in surface mining. It involves remote deployment of a continuous miner in openings beneath the final highwall, with no personnel entry. Many candidate areas for highwall mining have thick and steeply dipping seams. Mining downdip presents challenges related to the maximum pulling capacity of the machine, traction of the cutting head, and material conveying, all of which limit penetration depth. Maximum penetration is greater for flatter slopes and decreases for slopes nearing the threshold of the maximum machine operating angle. Most highwall mining operations are relatively flat with slight undulations within the seam; therefore, the highwall mining pillar design criteria applies fairly equally to the entire mining area. However, in steeply dipping deposits, design criteria based on higher overburden loads at the far end of the penetration are excessively conservative for the shallower portions of the openings near the highwall."

Jan 1, 2017

By N. P. Kripakov

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north-central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield-pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)-wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By David Gearhart, Peter Zhang, Gabriel Esterhuizen

"Researchers from the National Institute for Safety and Health (NIOSH) installed instruments in the track entry and in the pillars of a northern West Virginia longwall coal mine between two planned panels for the purpose of monitoring the behavior of the ground. The instruments included four cable bolt load cells to measure the change in gateroad loading, six borehole pressure cells to measure the loading in the pillars, three six-channel roof extensometers to measure roof sag, four convergence measurements on the cribs to measure the crib loading, and a multipoint borehole extensometer to measure the pillar expansion. The instrumentation was all connected through two multiplexers to a single Campbell Scientific permissible datalogger located about 350 feet outby the instruments. The goal of the project was to record all of the measurements as both longwall faces passed the site of the instrumentation and to use the data to calibrate numerical models.This report describes the recording of all of the measurements taken as the first panel approached and then passed the instrumentation site. This study provided valuable data related to the ground response and support performance that will be used to improve safety in longwall gateroads.INTRODUCTIONA longwall mine in northern West Virginia was selected as a second study site for an ongoing research project into gateroad layout and support design. The area was affected by a transition from limestone to sandstone in the roof. The entries were 16 feet wide, and the height was approximately 80 inches. The layout for the longwall panels was 1,170 feet wide by 4,000 feet long. The panel configuration was right-handed, and a three-entry gateroad was used between panels. The pillars next to the headgate were 137.5 feet by 115 feet center-to-center, and the pillars next to the tailgate were 275 feet by 100 feet center-to-center, with the crosscuts at 60 degrees. The width of the gateroad was a total of 215 feet."

Jan 1, 2018

By Lou Gaozhong, Guo Wenbing, Zhao Gaobo, Wang Shuren

"The height of a fractured zone due to high-intensity mining (HIM) plays a vital role in the safety analysis of coal mining under bodies of water. This paper described the characteristics of HIM. The processes of overburden failure transfer (OFT) are analyzed. The state of destruction transfers from a certain stratum to the upper stratum as face advance distance increases, and the processes of OFT are divided into two stages: transmission development stage and transmission termination stage. Through theoretical analysis, the limited suspension-distance and limited overhanging distance of each stratum are proposed to judge the damage of each layer. Based on this, the OFT criteria of fractured zone development are obtained. The mechanical model of strata suspended integrity and overhanging stability are established. Finally, a new method to predict the height of fractured zone due to HIM is put forward based on the processes of OFT, the limited suspension-distance, and the limited overhanging distance. Further, a HIM panel in the Datong coal mine is taken as an example. Theoretical methods are proposed, and engineering analogy is used to predict the height of the fractured zone, which is compared with in-situ measurements reported in the literature. The results show that the in-situ measurements for the height of the fractured zone are in close agreement with the theoretical calculation result. Therefore, the rationality and reliability of the theoretical method proposed to predict the height of fractured zone is verified.INTRODUCTIONThe height of the fractured zone (HFZ) due to the exploitation of coal is a key parameter for the safety analysis of coal mining under a body of water (Wenbing, Youfeng, and Hou, 2012). Accordingly, it is necessary to predict HFZ under the corresponding mining conditions before coal mining."

Jan 1, 2018