Search Documents

By Boqiang Wu, Ganggang Xu, Xiaodong Wang, Hai Wang, Shibin Zhu

"Using a paste-like slurry as a filling from the ground surface to the goaf, artificial pillars can be built in the cavity goaf to support the goaf roof to prevent roof collapse and ground subsidence. If the accumulation laws of paste-like slurry are known well, the filling technology can be optimized. The laws can establish the foundation for finding out the best methods for building artificial pillars and filling technology. In order to understand the accumulation laws of paste-like slurry in the cavity goaf, Aeolian sand with wide distribution in northwestern China was selected as aggregate, and Portland cement was used as cementitious material to prepare a paste-like slurry. A test model of the cavity goaf was built to simulate the filling process by pump from the ground surface to the goaf to study accumulation laws of the paste-like slurry. The results show that the whole process of expansion and accumulation of the paste-like slurry could be divided into stages: free expansion, fill tightening expansion, and stable expansion. The angle of repose of the accumulation body of the paste-like slurry is constant in the stage of stable expansion, and it is the final angle of repose of the accumulation body. The angle of repose of the accumulation body is highly relevant to the slump of the paste-like slurry, and it is unrelated to the distance between the floor and roof. Under certain conditions of the cavity goaf, reducing the slump of paste-like slurry is one of the effective ways to obtain cost-effective pillars.INTRODUCTIONA large number of cavity goafs of coal mines were left in northwestern China; they were formed in the mining process by room-pillar or strip mining. Safety coal pillars were used to support the roof to keep long-term stability in the goaf, so the ground subsidence was not obvious (Fu, Deng, and Zhang, 2011; Xie, 2014). With gradual weathering, destruction of coal pillars, or additional load from ground surface buildings and structures, there could be a risk of instantaneous collapse of the roof in the goaf. This would affect the safety of existing structures on the ground and adjacent mines (Qu et al., 2017; Li, Xiang, and Jia, 2011; Tan, Guo, and Zhao, 2016; Tan et al., 2017). For disaster prevention of the falling cavity goaf, the current common practice is full filling (Hu et al., 2008; Liu, Zhu, and Huang, 2015; Pan and Wu, 2010). However, for buildings and structures with lower deformation requirements, full filling is excessive. For example, it is acceptable for goaf treatment under general roads and industrial sites to control the maximum deformation and keep the deformation continuous (Liu, 2011; Liu, 2012)."

Jan 1, 2018

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

By D. G. Lynch, M. R. Martin, R. J. Coutts

"Broadmeadow Mine is an underground longwall mine located in Central Queensland, Australia. The mine introduced a top coal caving (TCC) longwall face in 2013 but since then has experienced severe convergence events at the start of each panel after 60–70m of retreat, resulting in equipment damage and the longwall almost becoming iron bound. A significant geotechnical monitoring effort during LW10 and LW11 to characterise the caving mechanics and operational changes during LW11 were successful in mitigating the risk posed by these initial convergence events. This paper describes the geotechnical monitoring programme undertaken during LW11, the operational methods used to mitigate these initial convergence events, and the contribution to these events of the TCC technique.A thick sandstone unit close to the extraction roof was likely the cause of the convergence events at the start of each longwall panel. However, stress change monitoring cells, surface extensometers, an inclinometer, and the blockage of holes designed for pre-conditioning using hydraulic fracturing indicated that the convergence events were not caused by the sudden collapse of sandstone bridging across the goaf. Rather, they were caused by the propping action of strong units within the overburden strata. Equipment design modifications were made to allow the longwall to remain operational during the convergence events and an operational strategy was implemented to mitigate convergence in LW11. The initial convergence event was successfully negotiated, and Broadmeadow went on to be the highest producing longwall for CY16 in Australia.INTRODUCTIONBroadmeadow Mine is an underground longwall mine located in Central Queensland, Australia, owned and operated by BHP Mitsubishi Alliance (BMA). The mine is a punch longwall mine using open cut pit access provided by Goonyella/Riverside Mine. Broadmeadow commenced longwall operations in 2005 using a conventional high reach longwall, but later changed to the top coal caving (TCC) method of extraction. Broadmeadow extracts the easterly dipping 5.5–7.5m-thick Goonyella Middle Seam in ranging in depth from 90m to 330m. The coal is washed and blended at the adjacent Goonyella/Riverside open cut mine to produce a premium coking coal product for export."

Jan 1, 2018

By Mark Van Dyke, Gamal Rashed, Khaled Mohamed, Timothy Barton, Morgan Sears

"The unconfined compressive strength (UCS) of coal is an important parameter that controls the stability of coal ribs in underground mines. Estimation of the UCS of coal units composing the rib is required for conducting the rib stability assessment technique. This technique requires conducting large numbers of conventional UCS tests in a laboratory, which are expensive and time consuming. The research work outlined in this paper examines the use of indirect strength estimation methods—the point load test (PLT) and the in-situ Schmidt hammer test (ISHT)—for evaluating the intact strength of coal. The conventional UCS test was conducted on 80 coal specimens from 10 different coal seams for eastern coals. For each coal seam, the PLT and the ISHT were compared with the UCS test results to establish a correlation between the strength indices from the PLT or ISHT and the UCS. Moreover, to simplify the estimation of the UCS, a correlation between the megascopic coal lithotype and UCS was established.INTRODUCTIONBased on Mine Safety and Health Administration (MSHA) reports, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States over the past decade (MSHA, 2018). In an attempt to control rib failures in underground coal mines, the National Institute for Occupational Safety and Health (NIOSH) is working on developing a coal rib stability rating technique to provide a quantitative means to characterize the stability of coal ribs and to provide guidelines for early selections of rib support. The unconfined compressive strength (UCS) of coal units composing the ribs is one of the key input parameters required to estimate coal rib stability. The UCS of coal is an important parameter that controls the resistance of coal ribs to fracturing and slabbing. Direct determination of the UCS is time-consuming and expensive. Moreover, the UCS may be limited to testing only the strong coal samples since the weak or highly cleated samples might not survive the transportation and the preparation process (cutting and grinding). Therefore, alternative methods have been tested to indirectly find the intact strength of coal, such as the point load test (PLT) and the in-situ Schmidt hammer test (ISHT). The acronym ISHT refers to Schmidt hammer tests that were conducted in-situ on coal pillar ribs, while the acronym SHT refers to tests that were conducted on small scale blocks of coal."

Jan 1, 2018

By Kristineq Pankow

The August 2007 Crandall Canyon mine disaster raised national awareness of mining-induced seismicity (MIS) in Utah as well as general interest in how seismic monitoring might improve mine safety in the region. Unlike the situation in most other mining areas in the U.S., local seismographs in Utah?s Wasatch Plateau (WP) and Book Cliffs (BC) coal fields are an integral part of a modern real-time earthquake information system developed by the University of Utah Seismograph Stations (UUSS) as part of an Advanced National Seismic System. The UUSS earthquake catalog contains a continuous record of MIS at all active mine sites in the WP-BC region since 1978 (more than 18,000 seismic events = M 4.2). We describe characteristics of MIS and current seismic monitoring capabilities in the WP-BC region. We then demonstrate, using MIS from an example Utah coal mine, the ability to refine event locations with estimated absolute errors of ~200 m or less using a combination of (1) a double-difference relocation methodology and (2) ground truth information provided by mine operators. This approach enables sufficient spatial resolution to correlate MIS with mining activities, providing a useful tool to help improve mine safety.

Jan 1, 2008

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By Peng Zhang

In a recent research effort, a laminated overburden loading model (as implemented in LaModel3.0 was compared with the results of ARMPS 2010, and the laminated overburden model was found to more accurately classify a ARMPS database of 52 deep cover case histories by a factor of 60% versus 54%. However, the LaModel analysis of each case study required several days to complete, as compared to a requirement of only several minutes for each ARMPS analysis. In the research presented in this paper, a computer code (ARMPS-LAM) has been developed to effectively implement the laminated overburden model into the ARMPS program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition and then automatically develops, runs, and analyzes a full LaModel analysis of the mining geometry to output the stability factor on the Active Mining Zone(AMZ), all without further user input. The present laboratory version of ARMPS-LAM can be run in batch mode; therefore, the ARMPS 2010 database of 645case histories can be analyzed very quickly. In an initial logistic regression analysis of this database, the ARMPS-LAM program was seen to be slightly more accurate than ARMPS 2010 by a factor of 71% versus 63%.

Jan 1, 2013

By Robert A. Siokler

Approximately 75 percentage of the earth's land surface is comprised of shale or shale-like materials. Shale itself is composed of the residue from an almost infinite variety of weathered parent materials which have undergone deformations ranging from intense to negligible. Under standard test procedures, shales exhibit a very wide range of physical properties particularly if the test specimen is subjected to a change in moisture content, when the original test values may vary from 0 to 100 percentage. It is this wide variation in physical property values compounded by its ubiquitous presence that makes shale such a problem material to engineers. In reviewing the literature relating to shale, it is evident that the "problem" has been approached from many directions. In order to understand why shales behave as they do, investigators have sought mineralogical, geological, chemical, electrical, and physical answers. Each study yields valuable academic information, but few contribute much of value to the engineer in the field. Many valid relationships between shale strength or competency and clay type, clay content, organic content, water content, grain size, cementation, density, porosity, etc, have been established. Yet it is very difficult to extend these understandings to the in situ condition with results that can be used by the field engineer. One major reason earlier work has not produced better information lies in the ambiguity of the definition of shale. It is apparent that no one laboratory parameter can be successfully used to provide sufficient engineering information to properly describe in situ conditions. For example; shale with swelling clays will produce low strength values provided: the swelling clay is in sufficient quantity, the clay is dispersed throughout the medium involved, and there is a low value of cementation. Shales with high unconfined compressive strengths have been found with very low shear strengths. Sandy shales often provide as many ground control problems as clay shales. Shales of similar nature may provide good roof conditions in one part of a mine yet in another part of the same mine the apparently identical shale may cause substantial problems. A clear need exists to classify shale in a manner which will enable the engineer to better predict the strength and durability of shale-like materials. Studies at the University of Missouri-Rolla (UMR) have focused on finding parameters which influence durability and competency, while being discretely discernible through uncomplicated testing. Initial research concentrated on distinguishing shale8 on the basis of standard physical tests such as: unconfirmed compression, triaxial shear, and slake durability. As results accumulated, however, it became evident that moisture content played a much greater role in determining competency than had been recognized previously. As a result the focus of the research turned to developing tests which would evaluate the influence of moisture on shale behavior. The above work then became a foundation for a second phase of investigation in which a suite of standardized tests were developed to provide a classification procedure. From this study five tests were identified as being critical: Moisture Activity, Atterberg Limits, Submersion, Unconfined Compression, and Shore Hardness.

Jan 1, 1986

By Tony Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and Laurel Hill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereonet, and rose diagram projections so that the Loyalhanna's structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts. pillar sizes, etc., that lessen miner exposure to these hazards.

Jan 1, 2002

By Anand Bhagwat

Surface control can prevent the falls of ground between primary roof support systems and rib support. Using existing industrial products, and adopting them for mining applications, has historically attained surface control in underground mining. However, the latest innovative solution, a revolutionary wire mesh product, is designed specifically for underground mining applications jointly by Bekaert and Orica. This knotted wire mesh, FlexKnot? 2500 and FlexKnot? 3500, uses smaller gauge, higher tensile strength wires, than a chain link fence or welded wire mesh. The higher tensile wire enables the mesh to achieve greater ultimate load-bearing capacity, with significantly lower overall weight. Test results, obtained at the National Institute for Occupational Safety & Health (NIOSH) Mine Roof Simulator facility, illustrate the comparisons of the new FlexKnot with traditional 8- and 10-gauge welded steel mesh. The FlexKnot is superior in deflection, load-bearing capacity, and stiffness?categories that are critical in achieving safer surface control. It also offers enhanced corrosion resistance because of the galvanized coating applied on the individual wires prior to the knotting process. Case studies from underground coal mine installations confirm that FlexKnot has the ability to significantly reduce installation cycle time and to minimize use and repetitive manual handling of individual mesh panels. An added advantage is the ability to supply FlexKnot in rolls for quick and easy handling for either rib or roof support application. When using rolls, the bolter can install the entire roll with one continuous forward motion, unlike the wasteful back and forth travel for mesh panel.

Jan 1, 2014

By Morgan M. Sears, lhsan B. Tulu, Ted M. Klemetti

"Why do some room and pillar retreat panels encounter abnormal conditions? What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal conditions when they are encountered? To help answer these questions, and to determine some of the relevant factors influencing the conditions of room and pillar (R&P) retreat mining entries, four consecutive R&P retreat panels were evaluated. This evaluation was intended to reinforce the influence of topographic changes, depth of cover, multiple-seam interactions, geological conditions, and mining geometry.This paper details observations made in four consecutive R&P retreat panels and the data collected from an instrumentation site during retreat mining. The primary focus was on the differences observed among the four panels and within the panels themselves. The instrumentation study was initially planned to evaluate the interactions between primary and secondary support, but produced rather interesting results relating to the loading encountered under the current mining conditions. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the stress conditions. Both the LaModel 3.0 and Rocscience Phase2 programs were used to evaluate these four panels. The results of both models indicated a drastic reduction in the vertical stresses experienced in these panels due to the full extraction mining in overlying seams when compared to the full overburden load. Both models showed a higher level of stress associated with the outside entries of the panels. These results agree quite well with the observations and instrumentation studies performed at the mine.These efforts provided two overarching conclusions concerning R&P retreat mine planning and execution. The first was that there are four areas that should not be overlooked during R&P retreat mining: topographic relief, multiple-seam stress relief, stress concentrations near the gob edge, and geologic changes in the immediate roof. The second is that in order to successfully retreat an R&P panel, a three-phased approach to the design and analysis of the panel should be conducted: the planning phase, evaluation phase, and monitoring phase."

Jan 1, 2016

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By Michael Murphy, Khaled M. Mohamed, Berk Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in underground coal mines to reduce rib fall accidents and fatalities. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified.This paper presents a coal rib model to simulate the mechanism of coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff Mine in Australia. Fracturing of the coal rib was defined by critical VALUES (of plastic shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data.INTRODUCTIONCoal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face failure and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities (MSHA, 2015)."

Jan 1, 2016

By William J. Schloemer

INTRODUCTION The history of coal mining the Ostrava Region of the Czech Republic goes back nearly 250 years. Both coking coal for steelmaking and thermal coal for the production of energy are mined here; however, it was the coking capabilities that subsequently turned the region into a major steel-producing area in the early 1800?s, something that continues to this day. Ostrava lies in the northeast corner of the Czech Republic, near the southern border of Poland, and falls within the Upper Silesian Coal Basin. The region contains over 400 seams of coal of which about 150 have been mined over its history and continue to be mined. Eighty percent of the Upper Silesian coalfieldlies in Poland and is presently mined by about 35 coal mines; the remaining 20% falls in the Czech Republic, which presently has four mines operated by OKD, a.s., a subsidiary of Amsterdam-based New World Resources. Traditionally, all the mines in this region have employed the longwall method of mining, of which subsidence is an unavoidable consequence. In fact, due to the long history of longwall mining here, there are areas where the overall subsidence has exceeded 37 meters (121 feet). The region is fairly densely populated with residences and industry, and a considerable amount of coal lies under some of these areas where subsidence is not allowed or has to be minimized. It is this reason that has driven OKD to consider alternate methods of mining that will not create subsidence. The decision was made to consider the room and pillar method of mining in order to leave stable pillars of coal to support the surface. After considering several locations, OKD chose the shaft safety pillar at the CSM mine as a test mining location. To say the least, this is a very challenging location in which to conduct a test. As with the entire region, there are many faults from tectonic activity, the seams are pitching at 12 to 20 degrees, the area is affected by high horizontal stress, and the depth of 750 to 900 meters is perhaps the deepest room and pillar coal mining ever attempted.

Jan 1, 2014

By Xinzhi Du

Coal strength is essential to analyze the stability of excavation in coal. It is well known that the strength of coal tested in the laboratory is size-dependent, and different size specimens will produce different strength. Many researchers have studied the uniaxial compressive strength of coal and developed a number of empirical formulae to describe the strength variation with specimen size. According to a comprehensive data base that includes most of the laboratory testing results in the last century in U.S. and South Africa, the size effect and shape effect were reviewed and analyzed. The results show that different groups of coal specimens have different size effect on the compressive strength. The critical size for the size effect from the data analysis is about 40 in. The shape (W/H) of the specimens has a large effect on the compressive strength. The pillar strength formulae obtained from the data regression have a larger strength than all other existing formulae. Most pillar strength formulae have their own place in coal pillar design field. In order to analyze the difference of those formulae, twelve design formulae have been selected to compare using the Pittsburgh coal seam. The intention is not to determine the preferred formulae, but only to compare them, and see how do the W/H ratio, width, length, angle, cross-section area and effective width affect different pillar strength formulae?

Jan 1, 2008

By Jinhua Wang

Based on engineering examples and theoretical analysis, the mechanism of chemical consolidation for fractured roadway surrounding rock was discussed. The chemical consolidating materials and three consolidating methods, that is, capsule, forced infusion and spraying, were introduced. Finally the application effects of the chemical consolidating technique to reinforce the fractured surrounding rock of roadways were analysed.

Jan 1, 1996

By Guy Reed, Russell Frith

"The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database.This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength “index.” These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of super-critical overburden behaviour as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases.A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.INTRODUCTIONThe inspiration for this paper is founded in three statements from two eminent persons in the field of coal pillar strength research, Jim Galvin and Essie Esterhuizen, as follows:Both Salamon and Munro and [the University of New South Wales] based the derivation of their pillar strength formulae on a criteria that the diameter of a panel of pillars, W, had to at least equal the depth of mining, H. This was thought to result in full tributary loading. It is now known that there are some mining environments included in both the South African and Australian databases in which mining span must exceed depth by a considerable margin in order to achieve full deadweight loading. Hence, it is logical to conclude that these data points may have contributed to pillar strength being overestimated by Salamon and Munro and UNSW (underline added by authors). Normally, this should be of no consequence because it is reflected in the probability of design success associated with any given safety factor (Galvin, 2006)."

Jan 1, 2018

By Xicai Gao

With the intensification and expansion of deep coal mining, the surrounding rock stress environment becomes further deteriorated because of the complicated geological environment and powerful mining effect, so the major deformation of roadway appeared frequently. The proportions of floor heave are increasing and , the most serious problem is the floor heave of preparatory workings. The coal seam of Binchang coal area in Shaanxi province is at a depth of 621.6 ~ 817.0 m, the average thickness of the coal seam is 25 m, and the overburden and coal measure strata are the main regional aquifers and are highly permeable. The properties of water-weakening are obvious in the floor strata. The main preparatory workings or chambers were driven in the coal seam. The severe floor heave of the water chamber appeared during early mining and the amount was 180 ~ 910mm, and seriously affected the normal installation and use of the water chamber. Theoretical study and numerical simulation as well as the in-situ measurements were carried out to investigate the deformation and failure characteristic of the surrounding rock with non-support in the floor and the main reasons which caused the floor heave were determined. A new combined support technology was proposed which consists of overcutting, grouting, backfilling and invertedarch and bolt-grouting. The field monitoring showed that the cumulative convergence of the water chamber was 20mm, the maximum convergence speed is 1.2 ~ 2mm/d, the accumulative convergence of two ribs was 36mm and the maximum convergence speed is 2mm/d. The combined support technology will enhance the support intensity between the roof and floor, the two sides of the entry and improve the loading capacity of the floor effectively and the floor heave can be controlled effectively.

Jan 1, 2013

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By Anthony Iannacchione

Coal mine bursts have represented a major hazard for U.S. mining operations for more than 90 years. During this time, many prevention controls have been developed and tested. This paper reviews 11 prevention control techniques. Although coal mine bursts are not common events in most underground coal mines, their occurrence almost always requires a change in mining practice. Over the many years of dealing with these hazards, specialized requirements for layouts and novel extraction sequences have been developed on a site specific basis. The keys to mitigating risks are to properly assess the coal burst hazards and to possess the knowledge and skills to prevent or remediate their occurrence.

Jan 1, 2008