Search Documents

By Euclid P. Worden

INTRODUCTION Today, conventional raise boring is an accepted method of development in underground mines and on major construction projects. Over the years that this technique, and its associated machines and tools, have been under development, many articles have been written on the subject. To a great extent, these papers have reported operating results of one or more specific projects or have been generalized reviews of state-of-the-art machines and tools. This paper is intended as a review of the technique from an operational standpoint. Conventional raise boring, as opposed to the related variants box hole drilling and underground blast hole drilling, is a two step process consisting of the pilot hole drilling and reaming cycles. This author has covered the subject of pilot hole drilling in another article (1) . A good review of the current machines and equipment has been presented by Monroe (2) and an overall review of this entire technology was published by E&MJ (3) and Mining Journal, April, 1983 (4) . The subject of the reaming cycle is presented here together with some of the technical aspects of how the drilling tools are intended to be used. OPERATIONS Bit Change After the pilot bit has broken through at the end of the pilot hole cycle, a changeover takes place at both the machine and

Jan 1, 1985

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By D. Brady

There are many examples, historical and recent, from the underground coal mining industry where during emergency response the response and ultimately the outcomes, could have been significantly improved if adequate systems had been in place for the collection and management of relevant information preceding the incident, the acquisition of information during the incident and the use of the information for risk mitigation and decision making purposes. The subject and process of knowledge management is possibly the most critical for would be rescuers of endangered coal mine workers, as it has been demonstrated at numerous coal mine incidents that a lack of or mismanagement of crucial information can be fatal for both the rescuer and/or the endangered coal mine worker. This paper will underline the scope and importance of robust knowledge management systems for emergency response within the underground coal mining industry and the process by which it is being achieved within the Queensland Mines Rescue Service and the NSW Mines Rescue Service.

Jan 1, 2012

By S. Slottee

The technology of making and using ?paste? from mine tailings is increasingly well known by the minerals industry. The primary applications are water recovery and ?stacking? of tailings with minimal use of dams and ponds. This paper highlights some applications, other than water recovery and stacking, that have come to the attention of a paste thickener equipment supplier. As generated by thickeners, paste (also called ?thickened tailings?) is a non-settling, relatively high concentration, suspension of solids that can be pumped. Paste deposits with an angle of repose, allowing minimal use of dams. High solids concentration allows more water recovery at the paste thickener than is achieved in conventional and high rate slurry tailings thickeners. This paper is based on paste as produced in a flow sheet that includes a thickener, underflow pumps that are typically centrifugal, transfer pumps that can be centrifugal or positive displacement, and a distribution system at the deposition site. Examples of paste applications other than water recovery or stacking include: ?mine? an existing tailings pond by removing slurry, recovering coal or iron ore values, and return the new tailings to the pond as a paste that does not res-suspend; use paste to seal an existing tailings pond from leaking to groundwater or to an underground mine; extend the life of an existing tailings pond by thickening the tailings to paste; move an existing dry tailings impoundment to a new location by slurrying, pumping, paste thickening, and redeposit; minimize the size of a filter by paste thickening the feed; operate a paste thickener and filter in parallel on a tailings stream with re-mixing to achieve a high solids concentration. The use of paste tailings technology has been expanding over the last 15 years. The applications, both implemented and under consideration, are increasingly diverse and include all minerals tailings. Tailings handling designers should always consider a paste option to the conventional slurry solution.

Jan 1, 2011

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By Gary L. Nelson

An overview is provided of Franklin Industrial Minerals mica mine and plant operations located near Velarde, New Mexico. Operated by Franklin Industrial Minerals since July of 1990, several process and product modifications have been developed and instituted to improve the operation. In addition to a brief history of site operations, descriptions of the mining, beneficiation, delamination grinding, and product classification processes are reviewed. Supportive topics discussed include equipment modifications and improvements, product application diversification, and specific product characterization. Also reviewed are the key areas of safety, environmental responsibility, and programs pertaining to process quality control and product quality assurance.

Jan 1, 1994

By Otis M. Clarke

The purpose of geochemical research in the Alabama copper belt is to re-evaluate geochemical prospecting methods as related to igneous and metamorphic rocks in a humid climate. It is also a correlation of laboratory research on copper mineral solubility with geochemical anomalies over known mineral deposits. Geochemical prospecting in warm humid climates involves different problems and conditions than geochemical prospecting in semiarid areas. Stems and others (1972) reported soil surveys in a humid tropical environment in Bahia, Brazil, were not effective in outlining areas of copper mineralization. Clarke (1971) reported false anomalies in lateritic soils in Alabama over mafic rocks. Bjorklund (1971) reported biogeochemical sampling in Finland was ineffective in detailed work outlining potential mineralized areas, although it may serve to indicate regional areas of high mineral potential. During this investigation, water, stream sediments, residual soil, and organic matter, mainly twigs, were collected from three known copper-mineralized areas. Samples were selected so as to cross mineralized outcrops and results were correlated with copper stability charts as reported by Silman (1958) and Schmitt (1962). The geochemical research performed in Alabama should be applicable to other humid areas. Geologic, Climatic, and Pedologic Setting The area of investigation is in the southern end of the Appalachian eugosyncline in eastern Alabama. It includes the Hatchet Creek prospect, Pyriton mining district, and Stone Hill copper mine. The copper mineralization is in calcium-rich metasediments that lie along the western flank of a high rank metamorphic belt. All three deposits are in the uplands of the Ashland Plateau section of the Piedmont physiographic province. The Hatchet Creek copper prospect (Clarke, 1963; 1971) consists of three mineralized areas that contain pyrrhotite, pyrite, and chalcopyrite in small crisscrossing veinlets.

Jan 1, 1972

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By G. V. Henderson

The San Gabriel Valley contains some of the richest and most extensive sand and gravel deposits in California. Operating quarries within the San Gabriel area mine more than 15 million tons of high quality aggregate per year. This represents about 45 percent of the total mined in the greater Los Angeles area, one of the nation's largest aggregate markets and producing regions. Popular opposition to continued aggregate production in the San Gabriel Valley is high, especially in the city of Irwindale where 40 per-cent of the city's property is made up of "excavated holes," some 150-200 feet deep. Reclamation of 70 years of mining is now an almost impossible task. Zoning regulations have the effect of depleting these vast reserves rapidly by changing the definition of total reserves to include only "legally minable reserves." All but two or three of the aggregate mines now operating will be depleted or zoned out of business by the year 2000. Some studies indicate that there will be no aggregate mining operations by 1995. Recent studies show a drastic change in land use patterns within this valuable mineral resource area over the past 20 years. The San Gabriel Valley is a classic example of the lack of adequate regional planning with regard to urban development in MRA's and represents a "too little, too late" effort by local government and industry.

Jan 1, 1978

By Patrick J. Maessen, Bart H. M. Hendrix

"In the Netherlands, the Dutch Tunnel Standard has been developed for the execution of road tunnel projects. The Dutch Tunnel Standard is based on the Dutch Tunnel Law (WARVW) which sets the minimum safety standard for road tunnels in the Netherlands. Uniformity of tunnels and the uniform perception of a tunnel by its users leads to a higher safety level. Therefore, several items in the Dutch Tunnel Standard are specifically developed to ensure safety in emergency situations through the plane of human factors. Taking human factors into account is important in regular traffic situations, but in an emergency situation, this can be vital. In this paper, the development and contents of the Dutch Tunnel Standard are explained in the first part and in the second part, the systems related to human factors are described. DUTCH TUNNEL LAW AND THE NEED FOR THE DUTCH TUNNEL STANDARD In the 90’s of last century and the early 2000’s, several serious accidents occurred in tunnels in Europe. These accidents involved fire and led to many casualties. After these accidents, the European Union decided to change the regulations for tunnel safety, leading to the EU directive 2004/54/EG. The primary goal of this directive is, that casualties are minimized in case of a calamity in a tunnel (e.g. fire). In the Netherlands, the EU directive led to the development of the tunnel law and a tunnel regulation (in 2006) to prescribe the safety features required for a safe tunnel. The new Dutch tunnel law – cited in the Building Act – was meant to make tunnel design easier – but resulted at first in the opposite effect. Tunnel design in the Netherlands and design standards of Rijkswaterstaat Rijkswaterstaat – the executing organisation of the Dutch Ministry of Infrastructure and the Environment – is the owner of the tunnels in the Dutch national motorway network, thus owner of the majority of the road tunnels in the Netherlands. In the early years of tunnel building in the Dutch national highway network (approximately 1950 – 1970), Rijkswaterstaat was not only owner, but also designer of its own assets. Most Dutch tunnels are submersed tunnels, because these type of tunnels provide a cost-effective way to make river crossings. Another type of tunnel that is used, is a TBM tunnel. Because of the geological conditions in the Netherlands (merely clay/peat and sand), there are no NATM or drill-and-blast tunnels in the Netherlands. Since the last decades, land tunnels (covered roads) are becoming more common to provide for multiple use of surface space and to meet more modern environmental regulations as traffic increases near densely populated areas. Tunnel lengths in the Netherlands vary from 500 m to 1.5 km for river crossings up to 6 km for the Western Scheldt (bored) tunnel. The lengths of land tunnels vary from 500 m up to 3 km. With these increasing lengths, some safety topics and design topics arise, topics that were non-issues in the past, when tunnels were only used as river crossings."

Jan 1, 2016

By J. Andrew McGlenn, Brian McInnes, Bruce Downing, Murray Gant

The Second Narrows Water Supply Tunnel crossing beneath Burrard Inlet is an important component of the Greater Vancouver Water District’s plans to increase seismic resilience and meet increasing water demands. The project included the 110-meterdeep (350 ft) South TBM Receival Shaft, one of the deepest shafts to date in the sedimentary rock unit underlying much of Metro Vancouver. The shaft encountered varied sedimentary rock types, including fractured rock, with accompanying high groundwater inflows. This paper discusses the design and construction challenges associated with this shaft and the necessary means to complete the shaft in time for TBM arrival.

Jun 13, 2023

By Ken A. Phillips

Like the Arizona jeans commercial says: Arizona's not just a state, its a state of mines. Nearly 300 mines operate in Arizona making it the largest nonfuel mining state in the nation. Although copper is king in Arizona's mineral complex, nonmetallic minerals play important roles both regionally and nationally. Throughout Arizona's mineral resource development history industrial minerals have dominated over the metals for most, but not recent years. The State's metal mining industry which makes Arizona the number one mining state in the United States is a relatively young phenomenon. Arizona was an important industrial mineral producer long before her metal mining industry got started. Salt, phosphates, silicates, and oxides as food additives, tanning chemicals, gemstones, components of aboriginal ordnance, pigments, and construction materials are among the minerals produced long before copper, gold, silver, and the other metals became important. Around 92 % of Arizona's mineral industry is made up of nonfuel minerals, 86 % of that is accounted for by copper. Another 4 % is taken up by copper byproducts of molybdenum, silver, and gold. The remaining 10% of the production is occupied by non-fuel, non-metallic minerals. Arizona's 1994 industrial mineral production of nearly $380 million ranks us among the top 25 in the nation and higher than the total mineral production of at least 15 states.

Jan 1, 1996

By M. R. Carter

The Rochester Mining District is located some twenty-five miles NE of Lovelock, Nevada. The District was discovered and named in the 1860's by prospectors from Rochester, New York. For a number of years, they worked Rochester Canyon, sinking shafts and inclines and making open cuts. After reaching a depth of approximately eighty feet, the miners tapped an underground channel and were driven from these workings by a strong flow of water leaving pumps in the shaft and barely escaping with their lives. With the Rochester workings no longer accessible, the miners went to the southeast and established the Relief Mining District. About 1881, gold was found in the gravel at the mouth of American Canyon, to the east of Rochester. These placers were worked until 1895, first by the Americans who reportedly took out $1 000 000, and later by the Chinese who mined the gravel with great skill. It was estimated that the Chinese took out as much as $10 000 000.

Jan 1, 1987

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimeter precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many metalliferous and coal mines throughout the world. Over 80 systems are currently being used with current operations in 17 countries. Greater than 200 rock slope collapses and waste dump failures (from several to millions of tones) have been monitored, with ?warning? precursor movements recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines. Slope Stability Hazards and Rock Slope Monitoring in Open Pit Mines Surface mining often creates excavation boundaries which are steeper than those would be created under natural processes in the same rock type. They are also undertake quite rapid stress changes during mining and are influenced by significant external forces such as blast vibrations and changes in groundwater. These conditions are likely to allow some degree of instability to develop in the pit slopes. The hazards associated with this instability of pit slopes can be extremely variable in character; ranging from small cobble sized rocks dislodging and falling from mine benches to complete collapse of entire pit walls. It is usually the position of mine geotechnical or geological staff to assess these hazards for mine operations. The assessment of hazards due to unstable slopes can be done by visual observation of precursor signs such as fracturing or rilling of loose material. A more reliable indicator of instability involves the quantitative measurement of outward movement and acceleration of material as an instability mechanism develops. There is strong evidence that small precursor movements of a rock wall occur for an extended period prior to rock slope collapse (Hoek and Bray, 1981). Development of a monitoring system, adopting acceptable slope deformation criteria coupled with warning systems and design of stabilization or risk reduction measures if appropriate has become a standard method of dealing with slope instability. Framework for Slope Hazard Management using the SSR A framework for the management of slope hazards is shown in Figure 1 (discussed in detail in Harries, 2007). Although this framework is specifically for use with the Slope Stability Radar, a similar framework could be developed for other monitoring technologies for monitoring slope deformation. An important point to consider is the sequential nature of the hazard management framework from selecting the context ? identifying hazards ? analysing hazards ? evaluating hazards ? treating hazards. [ ] Once the context of the system has been developed (for example ? to monitor for rapid bench scale collapse), the identification of hazards is the next stage in hazard management. Identification of slope hazards can be relatively straightforward due to the visual nature of the information that the SSR system produces. The areas of excessive wall deformation are highlighted in color maps of the mine slope with a co-aligned photographic image to review the actual site of interest. The responsible personnel must then analyses this data, usually reviewing the deformation style and rate, as well as the size of area that appears to be failing. This information can then be evaluated against organisation protocols (for example it may be only a small sub-bench failure that will be ?caught? by existing benches and hence can be categorized as a lower risk). Once these hazards are evaluated they can then be treated if required. Two major options are available to reduce the risk during this treatment option. We can reduce the likelihood of failure ? for example by buttressing the failure or de-pressurising of water pressures in a slope. However, the most likely plan of action is to reduce the consequence of the failure. One of the most successful opportunities to reduce the consequence of a slope failure is to ensure that no personnel or mining equipment is present at the location of a slope failure when collapse finally occurs. This has been the major benefit of the SSR system to the different mining operations around the world. SLOPE STABILITY RADAR TECHNOLOGY OUTLINE Slope Stability Radar system specifications and capabilities: ? Measurement precision +/- 0.1mm (std.) ? Perforated dish and other features enable it to operate in high wind conditions ? Measurement range is 1700 metres ? Scans 270 degrees horizontally and 120 degrees vertically ? 1 ? 30 minute repeat rate for area scans (varies according to area being scanned ? RF exposure (<0.05mW/cm2) is a factor of 200 below the acceptable limit for the general population (1 mW/cm2) ? Tolerant to vibration and mining equipment ? The system weighs approximately 1500 Kg ? Remote area power supply enabling unmanned, continuous 24/7 monitoring ? Real time monitoring

Jan 1, 2009

By D. Gu

Shaft drilling is one of the most useful methods of driving shafts. This paper describes the application and development of the technique in coal mine construction in China.

Jan 1, 1993

By C. A. Young, J. D. Miller

Thermodynamic data has been obtained for oleate chemisorption at fluorite (CaF2) and calcite (CaCO3) surfaces using adsorption isotherms determined previously at room and elevated temperatures by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS). Linear regression analysis was used to statistically derive free energy data as a function of temperature assuming oleate chemisorption followed Langmuir-type adsorption. Enthalpy and entropy changes were subsequently ascertained from the Clausius-Clapeyron equation and fundamental thermodynamic relationships. Essentially, no difference in the free energy of chemisorption at the two mineral surfaces was found; however, the differences in enthalpy and entropy values were significant. By comparison, the results showed that oleate chemisorption at fluorite surfaces was more extensive and more entropically driven due to more water being displaced. Results correlate well with values determined in the literature for other mineral collector systems. These findings help explain the greater hydrophobic character of fluorite than calcite in both the absence and presence of oleate.

Jan 1, 2002

By Leons Kovisars

Introduction Labor is the major cost element for most mining operations. Labor costs are continually increasing, both in nominal and constant terms. This is true in developed as well as less developed countries. There are two ways to control unit labor costs - labor costs per ton of ore mined. Replace labor with capital (increased mechanization) or improve productivity (reduce the labor force). Every miner is aware of specific inefficiencies at his or her particular operation. But the miner has no comparative measurement standards. So it is difficult to know whether these inefficiencies are major or minor. The miner may also be unaware of large-scale inefficiencies because ongoing labor practices may have caused management complacency. Met Research studied mining labor productivity. The firm collected pilot data by sending direct-mail questionnaires to 320 nonferrous mining operations around the world. The response rate was 27%, of which 78 operations provided full data on production and employment.

Jan 11, 1983

By M. K. Eryadin, I. Yildirim, R. Asmatulu

Novel dewatering aids were tested on various coal samples from the U.S. and Canada in laboratory and pilot-scale filtration experiments. The reagents substantially improved the dewatering kinetics and reduced the cake moistures. The cake moistures were typically reduced from 20-30% by weight to 8-14% range in vacuum filtration. When the reagents were used in conjunction with a pressure filter, higher degrees of moisture reductions were achieved. In the present work, the novel dewatering aids were tested using different types of pilot-scale vacuum filters. The results were consistent with those obtained in laboratory experiments.

Jan 1, 2003

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019