Search Documents

By R. J. Sheets

In 2009 the Gold Quarry open pit mine, located 11 km northwest of Carlin, Nevada, USA, experienced multiple large-scale slope instabilities of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope instabilities occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower clay-rich sub-units of the Carlin Formation (Fm.). This deformation created preferential flow paths that allowed groundwater from the upper sandy sub-units to infiltrate low permeability clay-rich sub-units, thereby enhancing deformation of the slope toe which in turn destabilized the upper portion of the highwall. The outcome was a 160 m high slope instability that had a lateral run-out of 850 m. The effort to return the pit to ore production required both the geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This approach required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with blast induced, localized slope failures. Back-analyses applying numerical modeling indicated that the failure surface did not coincide with initial interpretations based on field observations; drilling results eventually confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the lower clay-rich sub-units. The outcome is a stable highwall within the Carlin Fm. following nearly ten years of repeated slope instability, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new open pit development.

Feb 23, 2014

Flooded-bed scrubbers on continuous miners have been shown to be an effective respirable dust control technology, traditionally used during the extraction of extended cuts of up to 12.2 m (40 ft). To effectively use scrubbers in faces that employ exhaust ventilation, the return ventilation curtain or tubing should be located outby the scrubber discharge on the continuous miner, which results in a setback distance from the face of approximately 12.2 m (40 ft). The goal of this research was to compare respirable dust levels generated in 6.1 m (20 ft) cuts when using extended curtain setbacks with a scrubber operating to dust levels in 6.1 m (20 ft) cuts when using traditional exhaust face ventilation without a scrubber operating. Dust surveys were completed at three mines with area and personal sampling conducted to quantify respirable dust concentrations on a cut-by-cut basis. Sampling results did not show a statistically significant difference in respirable dust at the continuous miner or shuttle car locations with and without the scrubber operating. However, with the scrubber operating, respirable dust concentrations in the return airstream downwind of the miner showed reductions of 91%, 86%, and 40% at Mines A, B, and C, respectively. The reductions at Mines A and B were statistically significant. Likewise, reductions in respirable quartz dust levels in the miner return were observed at all three mines, with statistically significant reductions of over 80% observed at Mines A and B. Consequently, operation of the flooded-bed scrubber did not impact respirable dust levels in the face area but did significantly reduce respirable and quartz dust levels downwind of the continuous miner. These results were obtained with the mines operating at or above the minimum operating levels specified in their ventilation plans.

Feb 23, 2014

By M. E. Grimes

The Port Radium mine of Eldorado Mining and Refining Limited, located on Great Bear Lake only a few miles from the Arctic Circle in north-western Canada, is the oldest uranium producer in Canada, The first concentrates were produced in 1933 and except for a period between 1940 and 1942 the mill has operated continuously. Although it is located in a remote area, and compared to more recent mines in other areas is a small tonnage operation, nonetheless the relatively high grade of the Port Radium ore has permitted operation to date on an economical basis. The mill process at Port Radium includes the original gravity concentration mill, and since 1952 an acid leaching plant which treats tailings from the gravity mill and tailings recovered by dredging of residues from underwater dumps in Great Bear Lake. The pregnant solution from the leach plant has to date been processed through aluminum reduction to yield an intermediate grade uranous phosphate-arsenate precipitate, Because of the rising costs of the aluminum reduction process, and its sensitivity to ore composition, Eldorado became interested in possible application to Port Radium of the solvent extraction processes of which we were obtaining increasing information in the latter part of 1954 and during 1955.

Jan 1, 1958

By J. Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world´s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards de-carbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain or Germany are only forerunners of this development - their centuries of coal production have been finished. The concept of Sustainable Development (SD) is fundamentally based on a model of progress where ecological, economic and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as: How can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry´s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later. INTRODUCTION Principally, mining natural resources is a finite business that reaches its limits once the deposits mined are depleted, the resources can no longer be mined in an economically profitable way, or substitutes are pushing the mined products out of the market. An example for the latter is the increasing replacement of coal with natural gas and renewables in power generation in the USA. (Kok 2017) According to the model of the product lifecycle, the global mining hard coal mining industry has reached the stagnation phase. (Kretschmann 2000) Although the coal mining business is more a multi-regional than a global business the trend is obvious. The peak of coal use is behind us, especially because the coal demand of China is slowly decreasing since 2013. (Shell 2018) China´s government has announced investing $360 billion in renewable energy by 2020 and scrap plans to build 85 coal-fired power plants. In March 2018, Chinese authorities reported that the country was already exceeding official targets for energy efficiency, carbon intensity, and the share of clean energy sources. China’s energy regulator, the National Energy Administration, rolled out new measures to reduce the country’s dependence on coal. (Kejun and Woetzel 2017) Coal consumption in the US is facing a 16 % decline in five years from 800 to 670 million short tons between 2015 and 2019 and - according to the EIA – will not rise again. (EIA 2018) The decline is attributed to complex market dynamics from low gas prices because of the “shale gas revolution” (Kok 2017, p. 3) to federal environmental regulation like the Clean Power Plan. The United Nations´ UNEP Finance Initiative is cooperating with the Portfolio Decarbonization Coalition of institutional investors to implement decarbonization strategies across their portfolio. Amongst these investors is the New York State Common Retirement Fund, the third largest public pension plan in the USA. (UNEP 2017) The European Union has already begun to de-scribe pathways to decarbonization. (European Union 2018) The Norwegian sovereign wealth fund, the world´s largest, excluded coal-related companies for ethical reasons. The oil giants Total S.A. and Royal Dutch Shell, tradi

Jan 1, 2019

By E. H. Boswell

The Mississippi embayment east of the Mississippi River is part of a vast geologic and hydrologic province. The abundance of water available is largely responsible for the agricultural history of the area and is perhaps the key factor in the rapidly accelerating trend toward industrialization. The multiple artesian aquifer systems that underlie the region, and the alluvial aquifer along the Mississippi River are virtually undeveloped sources of fresh water in that they are yielding only a fraction of the water available. The potential yield of the 12 aquifer systems is estimated to be about 25,000 mgd (million gallons per day), of which only about 600 mgd is presently being withdrawn. The amount of water in storage in these systems is about 1,600 trillion gallons. Ground water having a dissolved-solids content of less than 500 parts per million is generally available at depths of less than 1,000 feet, and water having a dissolved-solids content of less than 1,000 parts per million is available in some places to depths of more than 3,000 feet. Iron is the most common troublesome chemical constituent in the ground water. Water in varying amounts is also available from streams within the region. The amount of water which originates within the region and which leaves it as streamflow during a year averages about 50 million acre-feet (about 45,000 mgd). An additional 375 million acre-feet (about 340,000 mgd) leaves the region as streamflow during an average year, this amount having originated outside of the region. Some streams have considerable flow during periods of no precipitation, and the water during these periods generally has a low dissolved-solids content.

Jan 1, 1966

By D. H. White

The term "block caving" as used in this text includes panel caving and mass caving as described by Julin and Tobie (1973). This method reportedly was conceived in 1895 when a block of ore ranging up to 200 ft (61 m) in width was undercut at the Pewabic Mine on the Menominee Range in Michigan (Bucky, 1956). Over the years this method has evolved largely as a consequence of trial and error in which operators became acutely aware of what nature would allow and what it would not. Today block caving remains somewhat of an art rather than a science where experience often dictates what needs to be done. With the plunging prices of base and specialty metals in the early 1980s caving mines sought to reduce operating and development costs in order to return to profitability. For some this became an impossible task given the design, grade and operating costs of the day and closure became the only alternative. One lesson learned from the experiences of the 80s is that survivability depends on cost competitiveness and this implies the efficient use of resources and technology. To this end applied rock mechanics serves as a useful tool. The purpose of this paper is to show how Geomechanics can be used? in block caving to facilitate sound decision making and how this equates to dollars saved. Features of mining method selection, design and operation are discussed as related to this theme.

Jan 1, 1990

By L. F. Zeiler

In the past, health concerns in coal mines have primarily centered on those elements which have been essentially inherent to the mining environment. These would include respirable coal mine dust, respirable crystalline silica, excessive noise levels, and diesel exhaust particulates. Commercially-available chemical products are prevalent on mine property. These potentially toxic materials are chemical formulations that can degrease, clean, and lubricate metal parts, separate coal from rock in float/sink operations, and aid in roof consolidation, among other uses. As the general public has become more aware of the hazards of chemical exposures, miners have likewise become more concerned about working with an ever-expanding variety of chemical products on the job. Often, product or chemical specific hazard communication training is inadequate or ineffective, and miners do not know exactly what the ingredients are in the products they handle, or the health hazards involved with their use or misuse. Currently, the Mine Safety and Health Administration (MSHA), by law, enforces 1972 Threshold Limit Values (TLV). MSHA is making preparations to adopt new personal exposure limits for enforcement. The values given throughout the article are 1994 TLV's and are not enforcement standards, but are used for discussion purposes. They reflect the current scientific thinking regarding personal exposure to these chemical agents. An overview of these products is presented, and the potential health hazards associated with their use are discussed. Controls needed to prevent overexposures, such as proper handling procedures and personal protective equipment, are covered. Methods used to collect and identify contaminants are presented.

Jan 1, 1995

By N. B. Prenn

Case Studies in Open Pit Design Using Whittle 4D will be discussing the following four examples: 1) Optimization of process plant design using Whittle 4D as a sizing tool. In this case, the home office and project team had different views of the size of the final project. The home office wanted to reduce the size of the project to reduce capital expenditure, while the project team suggested a larger project. Whittle 4D was used to determine Net Present Value and Internal Rate of Return using the Whittle scheduler (FDAN) to schedule many alternatives, and calculate the NPV and return for each alternative. 2) Comparison of pit optimization methods: Lerchs-Grossman vs floating cone. Many pits are developed based on floating cone economics. A comparison of methods in one large gold mine resulted in the stripping ratio of the pit being reduced by 10% in the Whittle 4D optimization as compared to the floating cone optimization. 3) Pit optimization to determine if a new mill is justified. A large heap leach gold and silver mine needed to determine if a new mill was justified. The planning and scheduling would take several man months if completed without pit optimization and scheduling software. Whittle 4D software proved to be very effective in providing optimized pits and a mine schedule in a short time frame. 4) Pit optimization to determine how to mine and size. Open pit optimization determined where the underground operation should start, and whether the material should be processed by milling or heap leaching. One of our clients asked for help in determining where the pit should end and a new underground operation start. We used Whittle 4D to help determine where the pit should end and where to go underground. In addition the operation needed to determine how to process the material.

Jan 1, 1996

By G. L. Simmons

Aqueous pressure oxidation at low temperature, although desirable from a process engineering and operations point of view, presents unique problems when temperatures approach 160°C (320°F). In developing the pressure oxidation process for the Lone Tree Mine, elemental sulfur formation and agglomeration with pyrite proved to be a problem. This paper discusses some of the unique features of the Lone Tree sulfide deposit and its amenability to low temperature oxidation. Problems encountered during pilot plant operation and their solutions are discussed.

Jan 1, 1993

By Seung Han Kim, Andrew Yu, Carlos Jaramillo, Chu-Chieh Jay Lin

The Penstock Access Tunnel (PAT) concrete plug is a reinforced concrete plug separating the pressure tunnels from the personnel accessible tunnels and has leaked since the first filling at the Helms Pumped Storage Plant located in Fresno County, California. A grouting program was successfully implemented in 2009 to reduce the leakage from PAT concrete plug from over 1,000 gpm to 25 gpm. Recent observations indicated increasing water leakage through new pathways, leading to a decision to execute a high-pressure grouting and waterproof membrane installation program in 2017. The high-pressure grouting and membrane installation program was successfully executed in the areas adjacent to the PAT concrete plug where most of the inflows originated and the largest hydraulic gradients are suspected to present. It reduced the leakage from over 300 gpm of inflow to less than 20 gpm.

Jun 13, 2021

By Alton G. Woody

Like so many installations of its type approaching middle age, the ore processing and shipping facilities in Puerto Ordaz, Venezuela, have taken a lot of twists and turns in their lifetime. The object of this paper is to lead you through these twists and turns and some of the reasoning for them. The need for additional sources of iron are in the United States became evident during the time of the second world war. An exploration team from U. S. Steel located further high quality direct shipping iron are in commercial quantities near Ciudad Bolivar, Venezuela in 1947. Basic decisions were made to develop these reserves for export via the Orinoco River through a new shipping port to be built at the confluence of the Orinoco and Caroni Rivers. The basic concept was for the ore to be loaded directly to ocean going vessels. This was something of a gamble since the basic economics depended upon successfully opening up the main channel of the Orinoco River to deepwater vessels, and the Bethlehem Steel mine in the same area was already working with shallow draft river boats and a transfer station on the coast. Always, the basic philosophy has tended to be to plan with expansion in mind. The original conveyor systems were 1.52 m (60 inches) wide with 200 idlers, whereas 1.07 m (42 inches) or 1.22 m (48 inches) wide conveyors could have carried any production foreseen at the time of installation. Stockpiles have been located and designed with room for expansion. Basic designs have had dotted line future expansion blocked in.

Jan 1, 1978

By T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut-point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce cut-point and improve separation efficiency. Preliminary economic analyses show that the new circuit provides an attractive payback on the capital investment.

Jan 1, 1998

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 µ m fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 µ m. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1993

By M. Hakan Morcali, Onuralp Yücel, Haldun Gürcan, Serdar Aktas, Semih Özbey, Alper Keskin

"This work presents a method for the precipitation of cobalt sulfate by alcohols, specifically ethanol and methanol. The effect of the initial concentration of cobalt, the volumetric ratio of alcohol to cobalt sulfate solution, the addition of sulfuric acid and ammonia, and the effects of common ions on the precipitation percentage were investigated. The performances of ethanol and methanol were compared in terms of the precipitation percentage of cobalt sulfate, and explanations for different performances are offered. In the sulfate-based solution, the alcohol was shown to displace water ligands from the first coordination sphere of the cobalt(II) cations, which led to the precipitation of the cobalt ions as cobalt sulfate heptahydrate. SEM analysis revealed that the particle sizes of the powders produced by this method are smaller than those of commercially available cobalt sulfate. The scientific literature contains no data on the solubility of cobalt sulfate in ethanol. In this study, the solubility product constant (Ksp) for cobalt sulfate was experimentally calculated to be approximately 1.15 x 10-5.IntroductionCobalt sulfate, which is one of the most important compounds of cobalt, is used in the electroplating and electrochemical industries. The addition of cobalt sulfate to nickel-plating baths makes the treated metals brighter, harder, smoother and more ductile (Armstrong et al., 1988). It is also used as a desiccant for lithographic inks, varnishes, paints and linoleum, as well as in storage batteries, e.g., nickel-cadmium (Ni-Cd) and lithium-ion (Li-ion) rechargeable batteries (Kang et al., 2010). Cobalt sulfate is employed as a coloring agent in ceramics, enamels and glazes to prevent discoloration and as a copigment for the decoration of porcelain. In addition, cobalt sulfate has been used in animal feeds as a mineral supplement (Budavari et al., 1996; Kirk and Othmer, 1999).In the past, brewers used cobalt sulfate to prolong the life of beer foam (Kesteloot et al., 1968). Ranchers have dosed livestock with cobalt sulfate or used fertilizer enriched with this mineral to ensure that their animals obtained sufficient amounts of the trace mineral, which is essential to the production of vitamin B12. Cobalt sulfate has also been used in veterinary medication to prevent and treat cobalt deficiency in ruminants, which causes a reduction in feed intake and body weight, accompanied by emaciation, anemia and debility.Cobalt sulfate is a water-soluble bivalent cobalt salt. Cobalt sulfate heptahydrate dehydrates entirely at 420° C, and the dehydrated salt forms red monoclinic crystals."

Jan 1, 2015

By Rongdong Deng

A tower-like magnetic system comprising eight permanent magnets was installed at the center of a flotation column to separate chalcopyrite and pyrrhotite minerals. A cyclonic flotation was installed within the underpart of the column to separate the pyrrhotite from the gangues. A three-product magnetic flotation column was fabricated to create a magnetic field and a cyclonic zone. The products were Cu concentrates, pyrrhotite concentrates and tailings. The theoretical magnetic field strengths and the magnetic forces were calculated. The results of the flotation experiments showed that the Cu grade increased from 14.20% without the magnetic field to 26.40% in the presence of the magnetic field and that the S grade in the pyrrhotite concentrates increased in the presence of cyclonic flotation. The separation efficiency of this magnetic flotation column was evident. Therefore, this three-product magnetic flotation column may have a potential application, due to its high separation efficiency.

By N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline?s long-term performances and availabilities, to develop preventive maintenance plans, and to make future projections about the machine?s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, PAGE 736 and MARION 7820, which have been operating in Tunçbilek open cast coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages as: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data; (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (20 yd3) is seemed to be more reliable and less likely to fail when compared with Marion 7820 (40 yd3). The operating hours without failure range from 41 to 51 hours with 50 percent reliability.

Jan 1, 2011

By W. Collingwood

As open pit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in open pit mines is often recirculatory. This recirculation traps dust and gases in deep open pit mines. This problem is particularly acute in high latitude open pit mines due to a phenomenon known as an atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In open pit mines, this can result in unhealthy accumulations of gases and other contaminants in the open pit mines. In this study, the natural wind flow patterns in and around open pit mines were investigated using a computational fluid dynamics (CFD) program. Two dimensional models were created for a variety of pit geometries. The effect of depth, slope angle, and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2011

By Susan P. Taite, Alain R. Charest, Peter D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in the southwestern Chihuahua state of Mexico (Fig. 1). A Francisco Gold geologist discovered the prospect in1995. El Sauzal was encountered as a result of an extensive grassroots exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas silver camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiaryage. The mineralization appears tobe structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system, including kaolinite, illite, alunite, dickite and pyrophyllite.

Jan 1, 2005

P&H MinePro Services Canada is supplying Syncrude Canada three more of its model4100BOSS electric mining shovels. The shovels will be delivered during 2003. Syncrude’s oil sands operations already use five P&H shovels. The first 4100BOSS shovel was commissioned at Syncrude’s operation in northern Alberta, Canada in October 2001. The unit loads more than 9 kt/hr (10,000 stph) of unblasted oil sands. Since it began operation, the 4100BOSS has shown a 28% production increase over the four P&H 4100TS shovels also on site.

Jan 1, 2003