Search Documents

By B. Pesic

Manganese is about twelfth in the list of the most abundant elements in the earth's crust (Reidies, 1981). More than 150 known minerals contain manganese as an essential constituent (Mellor, 1932). In general, ores containing at least 35%Mn are classified as manganese ores, ores with 10-35%Mn are called ferroginous manganese ores, and ores containing 5-10%Mn are known as manganiferrous ores. One very important class of manganiferrous ores are manganiferrous-silver ores. They occur in the oxidized portions of the silver deposits of the Western United States. Silver is very often associated with manganese oxides which in some ore deposits are dispersed through calcite, causing the black color of the host rock, which is known as black calcite. Black calcites can occur in carbonate rocks (10-1500oz Ag/ton) and in volcanic rocks (less than 1.0oz Ag/ton).

Jan 1, 1986

By Bjørn Nilsen

"INTRODUCTION/BACKGROUND Weakness zones or faults containing clay-rich gouge represent one of the most challenging rock mass conditions to be encountered during tunneling. In Norway, such conditions count for a large part of the rock support costs, and in cases where the rock support has been insufficient, serious instability and cave-in have in many cases been the result. Most commonly, such cave-in has occurred after water filling of hydropower tunnels, but in some cases it has also occurred in tunnels under excavation and in completed “dry” tunnels. To avoid instability, two important requirements have to be fulfilled: 1) The location of the weakness zone and its character have to be identified in time. 2) The rock support has to be sufficient to withstand the loading caused by the zone. An incident which really brought the problems related to swelling clay into focus was the cave-in at the Hanekleiv road tunnel in 2006. Here, rock fall from the roof as shown in Figure 1 occurred unexpectedly about 10 years after the tunnel was completed. Fortunately this happened at a time with very little traffic, and nobody was injured. This incident emphasized the significance of the issue of swelling clay, although it was found to be caused also by gravitational collapse of the clay-rich gouge material of the weakness zone, and not related to swelling only (Nilsen et al. 2007).In this paper, main focus will be on discussing the characteristic features of swelling clay, test procedures which are being used for characterizing swelling clay, and the reliability of the results from testing for use in support evaluation and design in conditions with swelling clay. It is generally well known that swelling clay may cause considerable pressure on support elements, but quantifying this pressure for reliable analysis and design of rock support is still a great challenge."

Jan 1, 2016

By J. H. Daniel

Dust-related respiratory disease remains the major health concern in mining, and health agencies are proposing more stringent standards. The U.S. Bureau of Mines (USBM) is investigating techniques to continuously monitor respirable dust in real-time during the coal or ore extraction process. Continuous monitoring will allow mine operators to evaluate hazardous dust concentrations and adjust the operations to produce less dust. Mine instrumentation applications include machine-mounted and hand-held monitors, personal monitors, and area/environmental monitors. Six dust detection methods have been considered to meet application requirements. These are: light-scattering instruments, a smoke-particle detection technique, correlation of pressure drop across the collection filter with amount of dust deposited, the Tapered-Element Oscillating Microbalance (TEOM) instrument, a method that relates the amount of dust collected on a filter with the vibration of the filter, and beta attenuation measurement of dust. Studies to date have identified the TEOM instrument and the technique of correlating the amount of dust collected with the vibration ofthe filter as having the most promise for success. Development of the machine-mounted monitor is the highest research priority. The application options and progress to date in developing continuous monitoring instrumentation are presented.

Jan 1, 1995

By X. Y. Yu, X. A. Wei, A. Zeng

"The flotation behaviors of diaspore and three kinds of silicate minerals - kaolinite, illite and pyrophyllite - using an organosilicon cationic surfactant as collector were investigated as functions of reagent concentration and pulp pH. The results show that the organosilicon cationic collector QAS122 is a suitable collector for the flotation of aluminosilicate minerals but has weak collecting ability with regard to diaspore, enabling the flotation separation of diaspore from silicate minerals using QAS122 as collector. The flotation of a bauxite ore was then studied in detail. Finally, a reverse flotation separation process was used to process a low-grade bauxite ore. It was concluded that use of the organosilicon cationic collector is effective. A concentrate with aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, of 9.67 was obtained from natural bauxite ore with A/S of 6.07 at pH of around 11. The Al2O3 recovery rate was 81.72 percent. IntroductionChina has abundant bauxite ore resources, but more than 98 percent of the bauxite ores are the diasporic type, with the characteristics of complex mineral composition, low aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, and difficulty of processing. The gangue minerals in bauxite ores are mainly kaolinite, pyrophyllite and illite, containing titanium and iron impurities (Zong et al., 2008). It is known that high-grade bauxite ore, with A/S greater than 8, can be processed directly by the Bayer process (Papanastassiou et al., 2002; Ma et al., 1996). However, Chinese diasporic ores have been processed mainly by the sintering process, which is environmentally damaging and energy intensive. Increasing the A/S of the diasporic ores using a flotation method is needed (Xia et al., 2010).Froth flotation is one of the most widely used processes to concentrate valuable minerals in beneficiation ores. It is particularly useful for separating finely ground ores from their associated gangue minerals. For diasporic bauxite ores, flotation is applied to obtain high-quality material for the Bayer process by increasing the A/S. Direct flotation has been shown to be an efficient method for the desilicating of diasporic bauxite ore (Wang et al., 2004; Xu et al., 2004), but reverse flotation has more advantages for this purpose, including less collector consumption, less foaming product and less effect on metallurgy (Liu et al., 2007; Hu et al., 2003; Hu, 2003; Luo et al., 2001)."

Jan 1, 2015

By E. Bakhtavar

It is considered that the most economical method for the exploitation of Gol-e-Gohar Area 3 iron ore mine is to combine open-pit and underground methods. In this regard, the most critical problem is the determination of optimal final pit depth. In this paper, a method which was recently introduced on the basis of economical block models of open-pit and underground is used to determine optimal final open-pit depth of Gol-e-Gohar Area 3 mine with due regards to the future underground mining option. Considering a low cost and productive underground method as a feasible alternative for extraction of the lower part of this deposit, room and pillar was selected. It is concluded that after the assessment and comparison of different values for depth, optimal final open-pit depth was determined to be equal to 285 m.

Jan 1, 2010

By R. A. Haney

The Mine Safety and Health Administration (MSHA) has conducted studies both in coal and noncoal mines to evaluate methods for sampling and separating diesel particulates from mineral dust aerosols. The agency is investigating size separation techniques to distinguish between diesel particulate and respirable coal mine dust. Additionally, ashing techniques have been used to distinguish diesel particulate from mineral dust in metal and nonmetal mines. As part of these studies, personal exposures to diesel particulate for various mining occupations have been measured. This paper describes the measurement techniques and summarizes the exposure levels for various underground mining operations.

Jan 1, 1990

By P. Hadzeriga

Ion exchange techniques have been growing fast and spectacularly in all phases of Science for the last two decades, but still its acceptance as a unit operation in Metallurgy is resisted. Mainly this is because ion exchange procedures are thought of as glamorous techniques by which only relatively expensive metals are to be recovered. Perhaps this concept comes from the early and basic marriage of uranium and other high price metals and ion exchange procedures. The general trend is that ion exchange technique requires equipment and materials which are too expensive to economically perform a chemical step whenever "cheap" commodities are produced. However, we are here presenting a means of utilization of waste hydrochloric acid by an ion exchange technique. We have studied this from the engineering and economic standpoint in a number of variations of the main procedure discussed here and we-conclude that under proper economic circumstances, the cost of the ion exchange material as well as the equipment and labor involved in the ion exchange section, is by no means unreasonable.

Jan 1, 1964

By P. A. Roberts

A proposal for a modified in situ leaching method for extracting gold from oxidized gold ores using a non-cyanide lixiviant is described. A non-cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide-bearing solutions into the subsurface. Oxidized gold ores were chosen as a focus because earlier research on the use of sodium thiosulfate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulfate breakdown. A reconnaissance research program involving ore characterization and hydrometallurgical test work on samples from four Australian ore deposits and preliminary reactive transport modeling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulfate and ferric EDTA and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples in bottle roll tests under anaerobic conditions. The ore characterization and reactive transport studies suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in-place leaching? has been adopted for the proposed gold extraction system.

Jan 1, 2010

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the United States, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available. The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts.

Jan 1, 1978

By Randhir Sehgal

Heavy media processes have been used for cleaning +28 mesh coals for a number of years, Two applications, i.e., the vessels and the cyclones are widely used in the U. S. for this purpose. The basic reason for the popularity of these systems is their extremely high efficiencies for particle sizes above 28 mesh, However, application of heavy media technology to fine coals below 28 mesh, has been limited due to the following reasons: o Inability to make size separations effectively at sizes below 28 mesh o Necessity of feeding large quantitites of magnetite to the separators o Difficulty of recovering magnetite in the presence of large quantities of coal o High levels of coal contamination in the recovered media, leading to high circulating loads and ineffective control of media gravity

Jan 1, 1981

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized, utilizing waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empiric testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicates that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate when compared to that of conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

Sep 23, 2021

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, R. Jacksha, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, a rugged, portable direct tensile test system was developed for measuring shotcrete adhesion strength in underground mines. During the development of this test system, more than 185 direct tensile tests were conducted with a common, commercially available macro-synthetic fiber-reinforced shotcrete that was applied to concrete test panels using a dry mix process and machinery. The average bond strength of the shotcrete to the concrete substrate typically increased as a function of the shotcrete’s curing age, ranging from 0.44 MPa (64 psi) after one day of curing to 1.58 MPa (229 psi) after 90 days of curing. Adhesion strength increased markedly between one and three days of curing, reflecting a similar trend of increasing shotcrete tensile strength with curing time. This robust direct tensile test system can improve mine safety by providing a reliable means of measuring shotcrete adhesion strength and also supplying important information about the quality of the applied shotcrete and the competency of the underlying rock.

Jan 1, 2010

By Alexander May

In its role of providing technology to promote the efficient use of minerals and mineral process waste, the U.S. Bureau of Mines has conducted research at: its Tuscaloosa Research Center to identify and develop high volume uses for phosphogypsum. Mixtures containing a maximum of 50 percent phosphogypsum, 6 to 10 percent lime, and the remainder fly ash had compressive strengths as high as 4,800 psi. The effects of the mounts of phosphogypsum, lime, and fly ash were investigated. Also, the effects of fly ash to lime ratios were studied.

Jan 1, 1983

By Robert R. Dorfler

We ought not look back unless it is to de- rive from past errors, and for the purpose of profiting by dear bought experience. - George Washington During the mid 1960's, the application of automation was introduced to Climax by two process control companies. In 1969 Climax decided to seriously consider improved control of selected areas of their milling process after preliminary research had been completed on two rougher ball mill grinding circuits. In 1971 the Climax Mill Department developed a direct digital control scheme for rougher milling, designed a remote control center for handling process water, planned to automate the central steam heating facility for energy conservation, and convert other plant areas to automation. All twenty rougher grinding mills and the industrial water system were automated by 1977. The idea of automating central heating and other areas was abandoned although some fuel conservation items were installed at the heating plant. During this period from 1971 to 1978, the mill capacity was expanded from 39,000 metric tons per day to 43,000 metric tons per day and cyclone classification was introduced to rougher milling. Ore quality changes degraded the milling recovery from over 90% to less than 85%. This report describes the procedure the mill used in developing the automatic process and the occurances that affected the timing and fina1 control logic. The report deals primarily with the automation of the ball mill grinding, classification and flotation process as this was the bulk of the seven-year project.

Jan 1, 1979

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Amilton Barbosa Botelho Junior

A new step in the Bayer process has been used to recover NaOH and to reduce its content in red mud. After digestion, the residue is separated from the Bayer liquor and goes through press filters, which enables the recovery of NaOH and decreases the moisture content. It is well known that red mud is one of the most important sources of scandium. For this reason, the goal of this work was to characterize a Brazilian red mud (BRM) for scandium recovery. The sample was collected after the press filter system process. Analysis of energy-dispersive X-ray fluorescence (EDXRF), scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS), and X-ray diffraction (XRD) was performed. Microwave digestion using an acid mixture was carried out to determine the concentration of the main elements. Fe2O3 represented 40% of the BRM, and the Sc concentration was 43 mg/kg. The SiO2 content was 24%, which is the highest value found in the literature, whereas the sodium concentration was the lowest. A literature review was carried out to compare results with BRM, as well as the current studies for recovery of scandium by the leaching/ion-exchange process. Scandium recovery using a leaching/ion exchange process may be possible with efficiency higher than 90%. The greatest challenge is the occurrence of silica gel formation during leaching.

Oct 19, 2020

By John S. Brock

During 1964 and 1965 a mineral exploration program was carried out over an area of approximately 250 square miles, located in the Anvil-Vangorda Creek area of east central Yukon, 125 miles northwest of Whitehorse. The Vangorda deposit, a massive lead-zinc sulphide body discovered in 1953, was centred in the area proposed for exploration, a northwest trending belt located between the southwestern flank of the Anvil Range and Pelly River. Exploration for base metals in the remote Anvil area had previously been restricted by poor metal markets in the late 1950's. Regional geologic information was also limited except for publication of a scale 1 inch to 4 mile map by the Geological Survey of Canada in 1961. To effectively explore this area, a combination of geophysical and geochemical methods were essential due to extensive overburden cover varying in depth from a few feet to over 300 feet. (Figure (i) Key Map) Dynasty Explorations initiated the first comprehensive regional exploration program in the Anvil area, utilizing saturation prospecting methods employing geologic, geochemical and geophysical methods. The program involved an approach demanding continual modification of technical and physical logistics. After a total of 12 months of field work involving an expenditure of approximately $450,00, massive sulphides were discovered which subsequently proved to be an economic orebody. Thirteen properties had been acquired and explored. Ten separate geophysical anomalies had been outlined by a combination of magnetic, electric and gravimetric survey techniques of which five were tested by rotary drilling and two by diamond core drilling. The discovery of the Faro deposit was a direct result of this program.

Jan 1, 1971

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

By A. Newman, M. Goycoolea

"In this paper, we consider an underground production scheduling problem consisting of determining the proper time interval or intervals in which to complete each mining activity so as to maximize a mine’s discounted value while adhering to precedence, activity durations, and production and processing limits. We present two different integer programming formulations for modeling this optimization problem. Both formulations possess a resource-constrained project scheduling problem structure. The first formulation uses a fine time discretization and is better suited for tactical mine scheduling applications. The second formulation, which uses a coarser time discretization, is better suited for strategic scheduling applications. We illustrate the strengths and weaknesses of each formulation with examples.IntroductionProject scheduling is an important aspect of underground mine planning that consists of determining the start dates for a given set of activities so as to maximize the value of a project while adhering to operational and re-source-availability constraints. Important activities that require scheduling include development, drilling, stoping and other ore-extraction techniques, and backfilling. Precedence relation-ships impose an order in which activities can be carried out based on their location in the mine: for example, the activity a associated with development of an area must be completed before the activity a´ associated with extraction of that same area can begin. Re-sources include attributes of the mining operation, such as the amount of extraction and mill capacity available per time period, and are determined by capital and equipment availability and other factors. In this paper, for our set-ting, resource-availability constraints consider the amounts of material that can be extracted and sent to the mill — that is, processed — per time period."

Mar 1, 2017