Search Documents

By Z. Man, X. Zhu, Y. Xian, Y. Tao

"Fine coal separation has been always concerned. The froth flotation is not efficient in desulfurization because of the low rate of sulfide liberation from raw coal, the natural hydrophobicity caused by sulfur concentration on the surface of sulfide, and the presence of large amounts of middling feed. An efficient centrifugal gravity separator was employed to separate for Shandong –0.5mm high sulphur coal, the partition curve of centrifugal separator was obtained with conclusion that the Ecart probable error value of the separator is 0.095, the imperfection I value is 0.128. Finally, comparing with the coal flotation using progressive release method, the result shows that the effect of the desulfurization with centrifugal gravity force field based on density difference between coal and minerals are much better than that of the floatation which operates based on the difference in surface properties. It provides a efficient technical way for fine coal separation. INTRODUCTION Coal plays the most important role in the energy consumption in China. Although natural gas, wind energy, nuclear power has made great progress in recent years, but the share of coal in the final energy consumption accounts for 70-80%, which is determined by energy storage of China. Under the requirement of environmental protection, the clean utilization of coal resources becomes more and more important, and the need has already been identified. Coal washing and processing plays an important role in the process of high-efficiency and clean utilization of coal. For the separation of fine coal, flotation is a traditional method for effective separation and has been used in large scale industrial applications in coal preparation plant. However, for the separation of difficult-to float coal, especially fine oxidized coal and low–rank coal with hydrophilic surface, flotation is usually inefficient [1-3]. Although many pretreatment methods have been adopted, including grinding, microwave pretreatment, new flotation reagents, the problem of efficient separation has not been completely resolved [4-6]. Thus, an enhanced gravity separation method using particle density difference rather than hydrophobic difference was proposed for the separation of fine coal. Many research results have proved that this is a practical and effective method of sorting. R.Q. Honaker used Falcon C10 concentrator, Knelson centrifugal separator and spiral separator to clean the fine coal with size of 600*210 µm and 210*37µm, the effects of different operating parameters on the separation index was discussed. The results show that the separation density of Falcon can reach 1.6, and the Ep value can reach 0.1-0.15. This paper revealed that for the separation of fine coal with high sulfur content or fine grained content. Falcon has high separation efficiency with low cost. Separation results present in another paper showed that the desulfurization efficiency of inorganic sulfur was better than that of flotation [7-8]."

Jan 1, 2017

By J. J. Poveromo

"Iron ore for alternate iron processes concerns alternate iron products designed for use in EAF (electric arc furnace) steelmaking processes. These alternate iron products include both DRI (direct reduced iron), HBI (hot briquetted iron) and merchant pig iron. Merchant pig iron can be produced in conventional blast furnaces, mini blast furnaces (including charcoal BF's) or novel processes such as RHF/SAF (rotary hearth furnace/submerged arc furnace) such as Iron Dynamics or RHF such as Mesabi Nugget. These novel processes are coal based and can use iron ore concentrates or recycled steel plant oxides. The blast furnace processes can use conventional feed materials: pellets, sinter, lump ore and coke. However, DRI and HBI processes are predominantly pellet based but require DR grade pellets that are low enough in acidic gangue (SiO2 and Al2O3) to avoid additional expense in the EAF process This paper will focus on the quality and availability of DR grade pellets for NAFTA DRI/HBI plants but also concentrates for fines based processes and feed materials for merchant pig iron production. INTRODUCTION This paper will outline alternative (to the blast furnace) competitive ironmaking processes and process routes. Within each section the types of iron ore to be utilized will be discussed. Before discussing some of the details of these processes, it may be appropriate to review some definitions and commonly used terms within this industry. DefinitionsDirect Reduction: Reduce iron oxide to metallic iron without melting. Unreduced ore compounds remain as undesirable oxides • Direct Reduced Iron: Iron oxide feedstock exits in same form as entered (pellets in, pellets out; lumps in, lumps out) • Hot Briquetted Iron: DRI that has been hot (1200°F, 650°C) briquetted to a high density pillow shaped briquette • Hot Metal: Molten iron in liquid form, above 2500°F, 1370°C • Pig Iron: Solid product of the iron blast furnace • Residuals: Undesirable elements such as copper, nickel, chromium, tin, sulfur, molybdenum and phosphorus • Gangue: Rock minerals in the iron ore such as silica (SiO2), alumina (A2O3), calcia (CaO), magnesia (MgO). These remain in the oxide form in DR processes. • Reduction: Fe2O3 + 3 CO = 2 Fe + 3CO2 2 Fe2O3 + 3 H2 = 2 Fe + 3H2O (Fe2O3 > Fe3O4 > FeO > Fe)"

Jan 1, 2018

By William W. Magnus

The Eastern Magnesia Talc Company has always had the problem of adequate storage at its various mines and mills of not only crude ore and finished product but also material in process. An opportunity arose a couple of years ago with the decision to build a new mill at West Windsor, Vermont, (Figure 1) to come as close to providing adequate space for ore and the ground talc in the new plant as money and judgement would allow. Since our engineering staff did not have the time to design and engineer the new facility, an architectural firm with complete engineering staff was retained. Our original thought was to contract all phases of the construction and installation, however, and I think this is a most important point for any small firm such as ours, we found that with good supervision we, as the contractor, could do the job faster and at a lower cost than the construction firms that bid on the work. For some 50 odd years Italian talc has had a virtual monopoly in the body powder area of the cosmetic industry. Due to the purity, superior lubricity and whiteness, naturally occurring in the talc from Italy, no talc in the Western Hemisphere could capture any but a very small part of the market. When the Italian supply was cut off during World War II, the United States' largest consumer of this talc decided that it was time to develop a domestic source of a satisfactory replacement.

Jan 1, 1965

By J. Philip Bromberg

The 1977 Clean Air Act Amendments will have a large effect on the coal-fired segment of the electric utility industry. Since electric power generation constitutes by far the largest single use for coal, this legislation has the potential to greatly affect future patterns of coal utilization in the U.S.A. The inability to depend exclusively upon low sulfur coal as an exclusive mode of compliance with New Source Performance Standards may greatly lessen projected demands for low sulfur coal by eastern utility boilers. The requirements of the legislation is discussed with particular reference to the needs of the electric generating industry, along with the technologies available for complying with the Act.

Jan 1, 1978

By Stephen A. Orr

Underground mining is a dynamic art and science with a diverse set of design, production, and economic criteria that must be considered before selecting an optimal method to extract the ore. While all methods can be technically classified as either self-supported, supported, or caving, the multitude of subsystems and existing variations bear witness to the fact that each orebody is unique and, as such, justifies an individual approach to optimize mineral extraction. In this sense, underground mining is an art. The ability to evaluate the unique characteristics of each ore body and utilize sound engineering principles to design the optimal system constitutes effective method selection. The task by no means ends at this juncture, however. Subsequent implementation requires an ability for modification. Very rarely are all the facts available to make a concrete decision prior to development of the resource. As a result, the risk of a wrong decision can never be eliminated. This requires a significant degree of flexibility with each method. Each unit of exploration, development, or exploitation work contributed to a deposit enhances knowledge of the ore body. The best mining methods are those that correctly account for the known parameters but provide an allowance for change at minimal cost and adapt to unanticipated conditions.

Jan 1, 2008

By C. K. C. K. Gupta

The rare earths in elemental form are required for a variety of scientific and technological purposes. They are not easily obtained in this form, due to the great chemical stability of the rare-earth compounds and the strong tendency of elemental metals to react with everything they come in to contact with, especially at high temperatures. Beginning in the 1950s, when sufficient quantities of separated rare earths became available, as the result of intense research and development, three processing routes were developed to accomplish the preparation of all 16 naturally occurring rare-earth elements. They are chemical reduction of the halide intermediates, the oxides and electrochemical reduction of chlorides and oxide-fluoride mixtures. Not all the processes are effective with all the rare earths. In spite of the celebrated similarity of trivalent rare earths, the physical properties of individual rare-earth elements are sufficiently different that a variety of techniques are required for their preparation. The development of reduction processes for the rare-earth metals are covered in this paper, with focus on the oxide reduction routes. The strong reliance of effective reduction processes on the fundamental science of reduction reactions is highlighted.

By Sunfangze Liu, Xumeng Chen, Yongjun Peng

Efficient separation of naturally hydrophobic gangue, such as talc and carbonaceous materials, from sulphide minerals in flotation is becoming a significant challenge in many processing plants due to the need to process lower grade and more complex ores. Considering the hydrophobic nature of these gangue minerals, prefloating them at the beginning of the flotation circuit in the absence of collectors and rejecting the concentrate is a common practice to remove these gangue minerals. However, sulphide minerals, such as chalcopyrite, can become naturally floatable due to surface oxidation and therefore may float together with naturally hydrophobic gangue. In this study, a new approach was developed to maximize the prefloat of hydrophobic gangue while minimizing the loss of sulphide minerals. The new approach introduced a prefloat cleaner stage where sulphide minerals recovered to the prefloat concentrate was depressed and separated from other hydrophobic gangue minerals at a low pulp potential with the prefloat cleaner tailing fed back to the main sulphide flotation circuit. Flotation tests were conducted using chalcopyrite and organic carbon. The results show that the proposed approach can significantly reduce the loss of valuable minerals in the prefloat flotation without affecting the reject of naturally hydrophobic gangue. Applying pulp potential control at the prefloat cleaner flotation stage also reduces the consumption of reducing agents while minimizing the effect of reducing agents on downstream rougher flotation.

Nov 23, 2020

By Reed S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-order grinding studies in a laboratory ball mill according to the procedures described in the text by Austin, Klimpel and Luckie, using a slurry density of 70 weight percent. The results were scaled to five larger mills of 0.56 m diameter by 0.91 m length (2 ft. by 3 ft.), 0.82 m by 1.52 m (3 ft. by 5 ft.), 3.36 m by 7.90 m (11.5 ft. by 25 ft.), 4.41 m by 9.10 m (14.5 ft. by 30 ft.), and 5 m by 11.1 m (17 ft. by 36 ft.), assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distribustions and capacities for batch grinding in the 0.56 m and 0.82 m diameter mills and open circuit grinding in the 0.82 m diameter and larger mills using a one-large/two-small reactors in series model fitted to the residence time distribution measured in the 4.41 m diameter mill. The simulated results were compared to plant data for ranges of mill capacities. It was found that the simulated product size distributions were in good agreement with the experimental values below the 70% passing sizes, but did not agree so well in the top sizes. The predicted capacities were in approximate agreement with experimental values for the pilot-scale mills, were about 7 percent too high for the 3.36 m and 4.41 m diameter mills and about 25 percent high for the 5 m diameter mill. Use of the Bond method with the measured Work Index of the phosphate ore gave capacity predictions that were 45 to 150 percent too high.

Jan 1, 1985

By Young C. Kim

Use of geostatistics to solve mining problems is gaining importance as the cost of developing new mines is increasing and there is a need to mine more marginal deposits. But, until recently, coal companies have shown little or no interest in geostatistics. However, the stringent quality controls on coal burning has led to a surge in interest in improved methods for estimating clean coal characteristics. Until now, most of the geostatistical applications have centered on the problems of estimating in-situ coal characteristics (Sabourin, 1975; Wood, 1976, 1979; Fang and Stark, 1976; Pauncz and Nixon, 1979; and Knudsen et al., 1980). Little work has been done in applying geostatistics to coal washability, except that by Armstrong (1980). Applying geostatistics to coal washability basically means the estimation of cleaned coal characteristics, with the aid of geostatistics. Cleaned coal estimation plays a very important role in overall emission control strategy, as can be seen by the general flow diagram of such a strategy shown in Figure 1. The scope of this paper is limited to one aspect of the overall emission control strategy shown in Figure 1; namely, the prediction of cleaned coal characteristics using geostatistics.

Jan 1, 1982

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We'll conclude with a view of what this holds for the future

Jan 1, 1976

By John D. Price

In the constant search for ways and means of improving the quality of coke and thus making its use at the blast-fornace more satisfactory and economical, it has become increasingly evident that the present laboratory tests do not show the full picture of a coke's value as a blast-furnace fuel. This fact was recognized by Dr. A. C. Pieldner thirty-five years ago: (Ref. 1) here is perhaps no phase of fuel technicology which has aroused more discussion or regarding which there is more difference of opinion than the properties of coke which make it most suitable for blast-furnaces and other uses." Dr. Fieldner followed this assertion with a statement to the effect that men who write on this subject today (1923) have, because of conflicting experimental evidence brought forth in recent years, far less positive opinions on the matter than did writers of some years past. One is led to wonder if these statements are not just as true now as they were when first made.

Jan 1, 1959

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program's use and interpretation of its results will conclude the paper.

Jan 1, 1984

By S. W. Cavender

The analysis of the results of metallurgical experiments is often complicated by experimental errors and uncertainty, the complexity of the system being studied, and the confusion of correlation with causation. Consequently, comparative statistics are used to determine if a difference exists between the outcomes of tests, an estimate of this difference, and the precision of the estimate. This paper reviews the use of significance tests and confidence intervals for the comparison of results from two tests, the use of reference distributions, and blocking and randomization techniques to reduce unavoidable sources of variability. These techniques are demonstrated using plant and laboratory data.

Jan 1, 1993

By A. A. Sobek

Controlled release systems delivering the required concentration of an effective bactericide over an extended time period have been developed by The BFGoodrich Company's ProMac® Systems group. The ProMac system is site-specific and includes a four-step approach to controlling acid mine drainage (AMD): (1) Diagnosing the problem, (2) Prescribing the treatment, (3) Supervising the application of controlled release bactericides, and (4) Honitoring the success of applied treatment. The success of the ProMac system is evidenced by improved water quality, healthy vegetation, a reduction in levels of acidophilic thiobacillus, and a corresponding increase in population of beneficial microorganisms.

Jan 1, 1986

By S. C. Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico, is a research and development project sponsored by U.S. Department of Energy, designed to demonstrate the safe containment for disposal of radioactive waste. A mine (repository) is currently being developed 2150 feet below the surface, in a thick salt bed which will serve as the disposal medium. Provision of a proper ventilation system at the WIPP Project is a major priority of those responsible for its design, management, and operations. As an ongoing effort towards this goal, it was decided to simulate the mine's ventilation system using Dravo's MINEVENT computer program. Specifically, the work included the development of the following simulation models: 1. Simulation of the current ventilation system 2. Simulation of the designed ventilation system for the following modes: o Mine Construction mode/shift o Waste storage mode/shift o Fire or exhaust filtration mode These computer models are useful in solving complex ventilation problems likely to be encountered in an R&D project, like WIPP. They are particularly helpful for the development of contingency plans to incorporate during emergency situations, such as fires, fan stop- pages, radiation leaks, etc. Also, they can be utilized when considering expanding certain underground areas to ensure the availability of adequate ventilation.

Jan 1, 1986

By M. C. Fuerstenau

Flotation data indicate that sulfonate and dodecylamine adsorb physically on Mn02 at ambient temperature. Oleate also adsorbs physically if the zero-point-of-charge of the Mn02 is sufficiently high. Chemisorption of oleate apparently occurs between pH 8 and 9, and this phenomenon is enhanced considerably at elevated temperature.

Jan 1, 1966

By Elisa Comis, David Chastka, Miriam Piemontese, Maria Chastka

The Lower Olentangy Tunnel (LOT) Project involves the construction of a 17,000 ft (5,200 m) long, 12 ft (3.65 m) internal diameter Combined Sewer Overflow (CSO) tunnel. The tunnel is excavated by using an Earth Pressure Balance (EPB) machine designed to cope with soft ground, weak rocks and water pressure. The project is located in the city of Columbus, Ohio and the main geotechnical hazards are related to the heterogenous soils and the low overburden in an urban environment. This paper focuses on the performance of the EPB first drive and the comparison between the design assumptions and the actual TBM performance during construction.

Jun 23, 2024

By Dennis P. Bryan

Nevada is especially well endowed with industrial minerals, both in the number of ore deposits and the diversity of commodities. More than 600 significant industrial mineral deposits, containing 22 principal commodities, are present, in the State. The materials produced in Nevada in 1978 had a value of approximately 113 million dollars, and additional processing of some of them (e.g. gypsum into wallboard, limestone and clay into cement) added considerable more value. Table 1 shows the value of Nevada's industrial mineral production in 1978. Nevada currently supplies 85 percent of the country's barite producing 1.6 million tonnes (1.8 million short tons) valued at 30 million dollars in 1978. Nevada is second in diatomite production and contributes one-third of total lithium produced. Other industrial minerals being produced include clays, fluorspar, gypsum, lightweight aggregates, limestone and dolomite, magnesite and brucite, perlite, salt, sand and gravel, and silica. In general, Nevada produces high-value industrial minerals which are not consumed within the State, but rather, are shipped out of State. In contrast, most more populous states produce larger tonnages of lower value industrial minerals which are consumed chiefly within that state.

Jan 1, 1980

By Elgin D. Bell

Within the next, year or two, Western Canada should overtake Mexico and France. to become the worlds second largest producer of elemental sulphur, surpassed only by the United States, By 1965, it should produce about 25% of the world's total elemental production and, about 10% of sulphur produced in all forms. In 1952 Alberta had but one small sulphur recovery plant. By 1962, it had fifteen plants with a total designed capacity of almost 6,000 long tons of sulphur per day and actual production of almost one million long tons per year. This decade of dynamic growth was the result of Alberta's rapidly developing natural gas industry. More particularly it was the result of approval in 1960 to export natural gas in large volumes into the United States. Prior approval to export gas from Alberta to eastern Canada and relatively modest volumes to the U. S. had resulted in the construction of several plants but none were of the scale required to serve the U. S. market.

Jan 1, 1963

By Joseph Githiria, Khadija Omar Said

Mineable material is defined using cut-off grade either as geological or economic cut-off grade. Both geological and economic cut-off grade affects the output generated in an open-pit mining operation. It distinguishes the amount of ore sent to the mill for processing and waste to the dump. This consequently affects the overall profits generated from the operation hence the need for cut-off grade optimization. There are several mining parameters that are considered in a typical cut-off grade model. They include economic, geological, and operational parameters. They have a significant effect to influence the cut-off grade selected in mining operations at any given period. Some of the parameters are stochastic in nature by having a random probability distribution that may not be predicted precisely. When selecting cut-off grades in a mine operation, the mining engineers must consider the dynamic nature of the operational parameters in order to maximize the net present value of the project. Modifying Lane’s cut-off grade model which was developed in 1964 to incorporate the stochastic parameters in the approach helps improve the net present value as shown in the paper. The modified Lane’s approach is developed into a stochastic computer-aided application code-named NPVMining. Using NPVMining, selected stochastic parameters are considered in this exercise to show the effect on the output (net present value). The selected parameters (price and grade-tonnage) are varied by ± 10%. NPVMining has a graphical user interface that makes it easy to use and displays results in a user-friendly way. It gives the user the choice to manipulate the data depending on the study being undertaken or any other factor affecting the specific mine. This paper analyses the effect of each of the selected mining parameters on cut-off grade using NPVMining to show the significance of monitoring their variance.

Jun 25, 2023