Search Documents

By M. H. Stanczyk

The Bureau of Mines made bench-scale laboratory tests on a sample of typical Florida phosphate slime to determine alumina and phosphate extractions obtainable by agitation leaching, by baking and curing, and by a leach-electrolysis scheme. Recovery of mineral values from leached slime pulps by resin-in-pulp ion exchange contact and the reaction of the leached pulps to filtration, flocculation, and settling were also investigated. The best extractions of alumina and phosphate were obtained by (l) agitation leaching with sulfuric, hydrochloric, or nitric acid at an elevated temperature or (2) curing or baking the slime with sulfuric acid. Alumina extractions ranged from 80.8 to 90.0 percent and phosphate extractions ranged from 93.3 to 98.4 percent when the slime was leached at 90° C with sulfuric, hydrochloric, or nitric acids. Baking the slime with sulfuric acid at 200° C for 4 hours yielded an alumina extraction of 92.3 percent and a phosphate extraction of 97.0 percent, whereas curing with sulfuric acid at 100° C for 24 hours gave slightly higher alumina and phosphate extractions. Flocculation and settling properties of the slime were virtually unaffected in all cases. Filter area requirements, although somewhat improved as compared to untreated slime, remained relatively high. The lowest filter area requirement obtained was 44 square feet per ton of dry solids treated per day. Contacting leached slime pulps with ion exchange resins depleted the leach pulps of solubilized values; however, the filtration and settling properties of the barren pulps were unaffected. A leach-electrolysis scheme resulted in some concentration of solubilized phosphorus, but the method showed little promise of being commercially feasible.

Jan 1, 1966

By R. Hogg, T. F. Dumm

"Abstract - With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.IntroductionTraditional gravity separation techniques such as jigging, heavy media and water-only cyclones, shaking tables, etc., have been used to remove impurities from coal ranging in size from about 15.cm (6 ln.) to about 150 µm (100 mesh). The coal washabilty or float-and sink technique ls a well-established procedure for determining the optimum extent to which a coal can be cleaned by such physical separation methods. Because of the desire to recover even finer coal fractions by gravity separation techniques, there is a need to extend the coal washabillty analysis into the ultrafine range. The purpose of this paper ls to describe some of the significant factors that influence fine particle specific gravity separation. Washability analyses have been performed on three ultrafine ( <10 µm) coal samples representing three general mining districts in Pennsylvania. Results of these analyses indicate that the washabillty technique can be successfully applied to ultrafine particles when proper care ls taken."

Jan 1, 1988

By John L. Edwards, Anthony T. Iannacchione

There has been a persistent need to forecast roof falls so that miner’s exposure to hazardous underground environments can be minimized. Several monitoring techniques have been developed and are used today with varying levels of acceptance in the mining industry. This paper examines the potential for monitoring microseismic emissions activity as a means of forecasting roof falls. The use of this activity to forecast roof falls has drawn only limited attention, resulting in a lack of published field performance data. This deficiency is being partially addressed by analyzing data obtained during longwall mining at Moonee Colliery in 1998. The Moonee data base contains a wealth of information concerning roof fall forecast parameters and the seismic alarm criteria used to develop these forecasts. Four seismic alarm criteria were developed and used by Moonee with varying degrees of success. Roof falls were forecasted 73% of the time with average forecast times of 54 minutes. Ninety percent of the predicted roof falls had a warning time, i.e., the time between warning and roof fall event, of greater than 1 minute. The fraction of forecasted roof falls decayed logarithmically as a function of warning time, until only 20% of events were predicted more than 100 minutes prior to roof falls. False alarms occurred in 50% of the warnings. Many of the false alarms were quickly followed by a cessation in mining which could have temporarily halted the on-going failure process. If mining had continued immediately after the false alarms, a roof fall may have occurred soon after. The microseismic activity collected from Moonee Colliery demonstrates that techniques to forecast roof rock instabilities in underground mines are possible.

By G. R. Hopkins

One of the largest items in the expense of operating a refinery is the cost of the fuel used in distillation and for miscellaneous purposes such as in the heating of buildings and in the generation of electricity. On a B. t. u. basis, the average refinery consumes approximately one-tenth as much fuel as it produces. Theoretically, the fuel consumption at refineries should be much smaller than this, but furnaces can not be designed to be 100 per cent efficient and, in addition, a large part of the waste heat is low-temperature heat which would not pay for the expense of recovering it. Annual surveys of fuel consumption at refineries have been made by the United States Bureau of Mines, beginning with 1925. During the 5-year period, 1925-1929, the refineries made steady progress in fuel economy. This is evidenced by the computed figures of heat requirement per carrel of crude oil refined, which show a decline from 829,000 B. t. u. in 1925 to 639,000 B. t. u. in 1929 (see fig. 1). In 1930, however, &apos;the trend in fuel economy was reversed and the quantity of heat utilized in refining the average barrel of crude oil rose to 672,000 B. t. u. There were undoubtedly a number of reasons for the apparent decrease in fuel economy at refineries in 1930, chief of which were the tendency to carry the distillation farther instead of merely topping the crude and a gain in the consumption of waste oils, such as acid sludge, which in actual practice yield less heat per unit consumed than has been theoretically assigned to oil.

Jan 1, 1931

By R. J. Leary

Iron and steel scrap has accounted for 45 to 50 percent of the metallics used by the steel industry. In an electric furnace which utilizes a 100-percent cold charge consisting of about 99 percent scrap and 1 percent pig iron, sensible heat from molten pig iron is not present as it is when hot metal is charged to open hearths and converters. A study of means for more efficient utilization of iron and steel scrap in steelmaking indicated that the time and fuel requirements to melt scrap were important cost factors, particularly in arc-furnace steelmaking. A process to preheat scrap economically prior to charging into the arc furnace has been developed, utilizing efficiently the heat from combustion of fossil fuels as a substitute for electric-arc heating in the initial stage of arc-furnace steelmaking. Scrap is loaded into a portable vertical cylindrical furnace body that is open at the top and has a perforated dropout door at the bottom. In the heating operation, the furnace body containing scrap is placed upon a hollow base connected to a flue, and then the burner and combustion-chamber unit is lowered on top of the furnace body. The stream of hot-combustion products flows down through the bed of scrap imparting heat to it, and the cooled gases exhaust through the flue. After the heating operation the furnace body containing hot scrap is transported to the arc furnace for charging. Thus, the furnace body serves as a charging bucket for top-charged arc furnaces, enabling this preheating process to be integrated into existing material-handling patterns in many arc-furnace plants.

Jan 1, 1961

By Roy F. Waters

An inventory was made by the Bureau of Mines of wastes of mineral origin, water requirements, treatment of wastes, and water treatment practice of 163 industrial installations in the Lower Missouri River Basin. This is the second and concluding report on the survey, conducted in cooperation with the Missouri Basin Field Committee of the Department of the Interior as part of the Missouri Basin project. Principal industries covered by this second report are: Sand and gravel, coal, meat, ice, brewing, paint, petroleum, chemical, fabricated metals, and a number of industries having either no waterborne wastes, or none of mineral origin. Gravel, sand, and silt from 47 producers are the major wastes, totaling 6 million tons annually, Coal mine wastes in the form of slurried solids from washing crude coal are second in volume, totaling 100,000 tons per year. They contain an average of about 40 percent coal. Salt is the third largest waste, amounting to 28,000 tons per year, Next is calcium carbonate, most of which is formed in water treatments, Because of its high unit value, chromic acid is important, although the waste quantity is much smaller; cyanide wastes are also significant because large quantities of sodium hydroxide and chlorine are consumed in their treatments prior to disposal. The various industries discharging wastes use 38 billion gallons of water annually; the recirculation rate is 109 billion gallons per year. The plants discharging no waterborne mineral wastes use 2 billion gallons of water per year and recirculate more than 1 billion gallons. Sand and gravel plants use 13.5 billion gallons; petroleum refineries use 10 billion gallons in direct use and recirculate 82 billion gallons per year.

Jan 1, 1962

By Martin D. Conyac

A 1984 Bureau of Mines investigation identified ho mineral resources in the Wilderness Study Area (WSA). However, four prospects in the WSA contain anomalous amounts of copper and silver minerals; one had traces of gold. Stratabound copper-silver occurrences appear to be prevalent. Quartz veins in the WSA locally contain trace gold, and one mine adjacent to the area produced some gold in the late 1800&apos;s. The WSA is underlain principally by Precambrian and early to middle Paleozoic quartzites, argillites, dolomites and limestones that have been complicated by faulting, generally tilted northeastward, and thrust southeastward over sequences of late Paleozoic sedimentary rocks. The stratabound copper-silver occurrences and gold-quartz veins are in Precambrian and Cambrian rocks in the western part of the WSA, as are similar deposits regionally. Sand and gravel, and limestone are abundant, but plentiful resources of these commodities are nearer established markets. In November 1983 there were 5 small groups of current claims oh the WSA boundary; none are patented claims. Probably less than 35 claims have been located within the WSA, mostly in the northwestern portion; hut over 100 claims have been located outside, near the northwestern boundary. Oil and gas leases nearly surround the boundary and 6 extend up to 1 mile into the study area. There has been no recorded mineral production from within the WSA. From 3 to 5 miles to the west, several lode nines in the Johnnie district have produced several million dollars worth of gold from quartz veins, and some silver and lead from galena-calcite veins. These veins generally trend northeasterly and dip northwesterly and probably do hot extend into the study area.

Jan 1, 1985

By Virgil A. Marple, Susanne V. Hering

"5.1 IntroductionTraditional impactors do not offer much size resolution for submicrometer particles; typically their finest size cut is around 0.4 µ.m. Yet for many aerosol applications it is useful to be able to size segregate aerosols in the size range below 0.4 µ.m. Diesel emissions, welding fumes, cigarette smokes and photochemically generated smog aerosols typically exhibit mass median diameters between 0.1 and 0.6 µ.m. When sampling these aerosols with a traditional impactor, fifty percent or more of the aerosol mass can penetrate the final impactor stage. Allhough the material can still be collected on a backup filter, the filter gives no size resolution. As a result, the investigator has no size information on a substantial portion of the sample. One needs a sampler that size-segregates the majority of the aerosol mass. A lower size cut of 0.1 µ.m or less is required for most combustion smokes and smog aerosol s.To obtain smaller cutpoints two types of impactors have been developed, namely low-pressure impactors and micro-orifice impactors. Both instruments can provide cutpoints as small as 0.05 µ.m. Low-pressure impactors were introduced more than twenty years ago (Stem et al., 1962), and a variety of these samplers are in use today. Micro-orifice impactors have been developed at the University of Minnesota within the last five years (Marple et al., 1981 ). To date theirs are the only examples of these instruments in use.5.2 Operating PrinciplesThe low-pressure and micro-orifice impactors use two different approaches to achieve their very small particle-size cuts. Low pressure impactors resemble ordinary impactors, but are operated at reduced pressures of 5-40 kPa (0.05 - 0.4 atm). They take advantage of the decreased aerodynamic drag on particles that occurs when the mean free path in the air is as large or larger than the particle diameter. Micro-orifice impactors operate at near atmospheric pressure, but employ very small orifices, 40 µ.m to 200 µ.m in diameter. The streamlines of the air impinging upon the impaction plate have correspondingly smaller radii of curvature; the air is accelerated more quickly, making it more difficult for the particles to follow. The basic operating principles for both types of impactors are evident from the particle Stokes number, defined as:"

Mar 1, 1989

By N. S. Dalal, A. H. Hoffman, X. Shi, D. E. Banks, J. K. H. Ma, Y. Rojanasakul

Excessive production of reactive oxygen radicals by alveolar macrophages is proposed to play an important role in oxidative lung injury. A major product of oxygen radical formation is the highly reactive hydroxyl radical (•OH) generated via a biologic Fenton reaction. In addition to its known ability to induce lipid peroxidation, recent studies have suggested that the •OH may exert its cytotoxic effect through the alteration of [Ca2+], homeostasis. To test this potential mechanism as well as to investigate the relationship between •OH and Ca" overloading in cytotoxic injury, isolated rat alveolar macrophages were exposed to externally generated radical system, H2O2 (0.01 to 1 mM) and Fe (1 mM) and their [Ca2+] levels and cell injury were monitored using quantitative fluorescence microscopy with the aid of the specific Ca" indicator, Fura-2, and membrane integrity indicator, propidium iodide. Electron spin resonance measurements using the spin trap 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) confirmed the production of the .OH radical by this system. Upon the addition of the radicals, the macrophages displayed a rapid initial rise in [Ca2+] which was followed by a slower but more pronounced [Ca2+], elevation that reached a level 3 to 5 times higher than the basal level. This process preceded cell death as evident by nuclear propidium iodide fluorescence. Depletion of extracellular Ca" inhibited both the [Ca2+], response and cell injury. Preincubation of the cells with the Ca" channel blocker verapamil or .0H radical scavenger mannitol similarly inhibited the [Ca2+], rise and loss of viability. Firefly luciferase assay of cellular ATP content demonstrated that the alterations in [Ca2+], following .0H treatment preceded the depletion of ATP. Changes in membrane potential caused by Na* substitution with K* had no significant effect on either the unstimulated or stimulated [Ca"], levels. Taken together, these measurements indicate that .OH-induced injury in alveolar macrophages is associated with the alteration in [Ca2+], homeostasis. The mechanism of •OH-induced [Ca2+] loading is not due to nonspecific membrane damage or energy depletion, but mainly due to an increase in Ca2+ influx through Ca2+ selective channels. This Ca2+ over-load state as well as energy depletion caused by the oxidant may activate certain cellular degradative processes leading to cell injury and death.

Nov 1, 1995

By K. L. Erickson, Gerald A. Munson

"The need for spodumene as a source of lithia for war purposes led to the exploitation of the Edison pegmatite deposit 1-1/2 miles southeast of Keystone, S. Dak. The operation was conducted during 1943 and 1944 by the Lor Mining Co., Rapid City, S. Dak. Spodumene concentrates in the ratio of 15:1 were recovered by hand picking from a sorting belt. This method was expensive and wasteful of spodumene, owing to the small size of the crystals.Data4/ obtained by the Bureau of Mines indicates that blunging with hydroflouric acid or sodium hydroxide is a prerequisite to selective flotation. Results of tests by Denver Equipment Co., Denver, Colo., indicate that economic recoveries can be obtained in an alkaline circuit after desliming.At the request of the Lor Mining Co., K. L. Erickson, metallurgical engineer, was permitted to work in the pegmatite research laboratory to verify previous investigations and to determine problems that might be involved in commercial milling. The ensuing investigation indicated that electrolytes in the mill water produced a profound inhibiting action on the flotation of Edison spodumone.An investigation of mill water from various sources showed that some waters are suitable for the process and others are not. Subsequent testing showed that all of the available waters are suitable after treatment. The flotation of the Edison spodumene in an alkaline circuit after desliming and using oleic acid as collector is efficient and economical when the water does not contain impurities.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B.Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches arc under the supervision of Dr. R. S. Dean, assistant director.As the work was of a practical nature, samples from possible mill-water sources in the southern Black Hills were obtained, and commercial softening and demineralizing methods were investigated. Data on various waters tested are given in table 1."

Jun 1, 1946

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By C. R. Sponsler, O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Research (CFR) Committee of the Coordinating Research Coouncil (CRC) 4/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 5/ Further reports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941. 5/ reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. 5/The present report presents analytical data for samples, representing the products of approximately 100 companies. Most of the samples represented in this report were obtained during December 1)55 and January 194o. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items, and brands comprising each group is as follows:Regular-price, 1,958 samples, 317 items, and 96 brands; premium-price, 1, samples, 292 items, and 85 brands; third-grade, 58 samples, 22 items, and 14 brands. The meanings of these terms as used in the surveys are as follows;"

Jul 1, 1946

By R. S. Dean

"It has long been recognized that the properties of polycrystalline substances are not the same as those of single crystals. These differences are especially marked in metels and metallic minerals, and are of greatest practical importance in metal working and ore treatment. The property changes encountered in passing from a metal single crystal to a poly-crystalline aggregate are the same as are produced by cold-working a metal or by the precipitation of a disperse phase. Hence, we may logically assume that the property changes are all due directly or indirectly to the formation of interfacial area or internal surface. Our problem, then, is to ascertain the physicochemical state of the metal atoms at such internal surface and show how this physicochemical condition accounts for the pronounced changes of mechanical, magnetic, and electrical properties that accompany increased internal surface.GENERAL CONCEPT OF INTERNAL SURFACEIn 1678, Huyghens attempted to explain the double refraction of calcite by postulating that crystals were built from a regular arrangement of ellipsoidal particles. Over 100 years later, Abbé Hauy concluded from his studies of cleavage that crystals might be built from small units, but the units were of the same shape as the entire crystal. This idea, which was prevalent in mineralogical thought before the advent of X-ray spectrometry, was discarded when the great success of Bragg made it appear that the chemical atoms were in reality the elements of structure. In the further development of X-ray technique, however, C. G. Darwin, in England, and P. P. Ewald, in Germany, found it necessary to postulate crystal units con¬taining many atoms. The latter gave the name of mosaic crystals to those so constituted. The individual units are supposed to Possess the ideal atomic arrangements revealed by the X-ray but are not oriented with respect to one another."

May 1, 1938

By J. D. Davis

The Bureau of Mines Coal Carbonization Laboratory has been interested for the past 20 years in the quality of coke in connection with the selection of coals for the manufacture of coke. The principal experimental. method of carbonization, whereby 100- to 200-pound charges are carbonized in sheet-steel cylindrical retorts with recovery and determination of the properties of coke, gas, and products, was developed in cooperation with the American Gas Association,4 5 and it is known as the BM-AGA method. Results of the investigations of 90 coals included in the BM-AGA Survey of the Carbonizing Prop¬erties of American Coals have been published; 6 and, in addition to these, about 200 coals have been carbonized over limited temperature ranges. Because coke from cylindrical retorts differs in shape from that made in rectangular ovens, the BM-AGA method has been criticized, although those who developed it have always believed that it served well as a means of measuring the relative strengths of cokes from different coals. It is recognized that no laboratory-method carbonization, even on a large twit, can yield results that exactly duplicate those obtained in commercial ovens and retorts. However, with the completion and satisfactory performance of an experimental vertical slot oven of 500-pound capacity at the University of Illinois Geological Survey Laboratory,&apos; the opportunity to directly compare BM-AGA coke with coke made by two-sided heating became available and the necessary test apparatus was installed. The Bureau of Mines slot oven, which is similar to that designed by the University of Illinois Geological Survey, has been used to carbonize 11 coals (or blends) tested by the BM-AGA method. This report compares the results obtained by the two methods.

Jan 1, 1950

By Arthur H. Redfield

The expansion of city street laving which characterized the ten years ended December 31, 1929, according to a survey of 201 representative cities, made by the bureau of Mines, reached it climax in 1927, with decreases reported for 1928 and 1929. The upward trend, followed by a decline, was general in cities of all sizes included in this study, but was most pronounced in cities of 40,000 to 100,600 inhabitant and in the Northeastern, Southeastern, and Southwestern States. In the North-Central States the trend of paving; was downward from 1925 to 1929; in the Pacific, and Rocky Mountain States it was generally upward. Over the nation as a whole, bituminous types of paving continued to lead, furnishing two-thirds of the total street pavement laid in the 201 cities from 1925 to 1929. The actual yardage of bituminous pavement laid in these cities, however, was 3.8 per cent less in 1923-than in 1925, and the ratio of bituminous pavement to the total pavement t dropped from 70.4 per cent in 1925 to 62.1 per cent in 1928, rising to 65.1 per cent in 1929. The area paved with Portland-cement concrete amounted to only one-fourth of the total, pavement laid in these cities from 1925. to 1923., but the yardage of Portland-cement pavement increased by half during the period, and its share in the total pavement grew from 19.3 per cent in 1925 to 30.0 per cent in 1928, declining to 29.5 per cent in 1929. Brick, block, and stone pavements, which constituted the remaining one-twelfth of the total pavement laid in the 201 cities, decreased one-third in yardage, and declined in relative importance from 10.3 per cent in 1925 to 6.6 per cent in 1929.

Jan 1, 1931

By R. E. Collom

The commercial development of petroleum and natural gas fields has reached its present status within 60 years and is still considered by some operators to be "100 per cent wildcatting." 1 A tendency to drill for gusher production, the production that yields big returns in spite of any mechanical defects in drilling methods, has frequently caused drillers to pass by oil-bearing strata of comparatively small yield and actually to overlook rich oil zones in proved fields; in addition, whole fields have been ruined by water because development methods were never carried beyond a hole-in-the-ground stage.2 Unfortunately, the petroleum industry has no mine dumps or tail. ing piles as at metal mines to yield fortunes through later and bette!' methods of treatment. The wasted oil and gas are gone, as are the time, money, and effort wasted in ill-advised or haphazard drilling. Probably as production costs increase less oil will be wasted, but the need to develop and produce from sands of low yield will become more urgent with the increase in consumption of oil and the decrease in supply. Hundreds of wells are producing steadily as the result of months and perhaps years of careful prospecting and of tests during drilling. The Bureau of Mines has studied the testing and drilling methods used at such wells, and presents in this paper a criticism of these methods and suggestions on future work. The term pr08- pecting here means correct identification and measurement of strata as they are exposed by the drill. The term testing means the determination of the kind and amount of fluid stored within the pores or crevices of any stratum exposed in the hole.

Jan 1, 1922

By W. W. Adams, T. D. Lawrence

"A. larger enrollment and a greater number of man-hours of employment by the enrolled companies were the outstanding features of the National Safety Competition of 1942, an annual safety contest conducted by the Bureau of Mines, United States Department of the Interior, for the promotion of safety among workers in the mines and quarries of the United States. The accident-frequency and accident-severity rates were somewhat higher than in 1941, but the frequency of accidents in relation to the number of man-hours worked was strikingly lower than in the earlier years of the 18-year period during which the contests have been conducted.Companies that enroll in the National Safety Competition compete for a bronze trophy known as the ""Sentinels of Safety."" Six of these trophies are provided by THE EXPLOSIVES ENGINEER annually for award by the Bureau of Mines. The trophies for 1942 wore won by an anthracite mine in Pennsylvania, a lignite mine in North Dakota, an underground metal mine in Tennessee, a limestone mine in Ohio, an open-cut metal mine in Minnesota, and a lime-:tone quarry in Pennsylvania. The trophies are presented to the companies for 1 year and are then transferred to the winners of the succeeding year's contest.The contest rules state that a mine or quarry must have at least 25 men employed underground or in the pit for at least 100 days, and the plant must be in operation 30,000 or more man-hours to be eligible for a trophy. The rank of mines and quarries is determined by accident-severity rates, or, in the case of accident-free records, by the number of man-hours worked."

Oct 1, 1943

By P. M. BIDDISON, G. G. Oberfell, George A. Burrell

The Bureau of Mines is conducting a series of investigations, with a view to ascertaining the most efficient methods of obtaining gasoline from petroleum and natural gas. This report deals with a method of extracting gasoline from natural gas by absorbing the gasoline in oil and subsequently separating it from the oil by distillation. The process is quite different from those of compression and condensation which have been used for a number of years for extracting gasoline from casing-head natural gas, and has not heretofore been described in the literature. MANUFACTURE OF GASOLINE FROM CASING-HEAD GAS. The extraction of gasoline from casing-head natural gas by compression and condensation methods has become a large and lucrative industry in this country. In the year 1915 about 65,000,000a gallons of gasoline prepared by these methods was placed on the market. In addition, in marketing this gasoline, at many plants an equivalent quantity of naphtha was blended with the gasoline, thereby utilizing for automobile fuel and other purposes a large quantity of naphtha that otherwise would have been unsuited for these purposes. The increase for the year 1915 over 1914 was about 22,000,000 gallons. For the year 1916 the production should be more than 100,000,000 gallons. The quantity of casing-head gas treated in the year 1915 by compression and condensation methods amounted to about 24,000,000,000 cubic feet; the average yield of gasoline was 2.57 gallons per 1,000 cubic feet. b This casing-head gas represents natural gas that formerly went largely to waste; hence the process represented a distinct and important step in the utilization of the natural gas produced in this country.

Jan 1, 1917

By J. H. Wiggins

In 1919 the United States was threatened with a shortage of gaso- line. In spite of this well-known fact, a detailed field investigation has shown that in one stage only of handling crude oil the volume of gasoline that evaporates is equal to one-thirtieth of the country's yearly gasoline production. This loss occurs during the few days that the oil is stored on the leases before being taken by the pipe line, and in 1919, in the Mid-Continent field alone, it amounted to 122,100,000 gallons. Large as it is, it is only a part of the loss on the lease. Investigation has further shown that the gasoline in crude oil evaporates from one-half to six-tenths as rapidly as the same gaso- line after being distilled and stored, all evaporative conditions being the same. Many wastes in the oil fields are called "necessary." By this is meant that the cost of preventing the waste is greater than the gain through saving. Evaporation losses have fallen heretofore in this category, but now they must be considered unnecessary. In other words, it is no longer economical for any handler of crude oil to permit losses through evaporation. In accordance with its purpose of seeking to conserve mineral resources, the Bureau of Mines investigated the loss of gasoline by evaporation in the storage and handling of petroleum. Inasmuch as most producers had not decided that their losses justified cor- rective measures and no evidence was available on the comparative losses in various stages of handling the oil, the investigation was limited to determining by experiment and observation the nature and magnitude of evaporation losses, where the greatest losses are, and the factor controlling evaporation.

Jan 1, 1922

By Keith L. Harris

The performance of the world economy improved significantly in 1984. Real world output!/ grew 4.3% (compared with 2.6% in 19831, the highest since the 4.4% increase recorded in 1978 (table 1). The output of industrial nations rose 4.9%, while that of the developing nations rose 3.7%. The United States and Japan had the largest increases in output of the major industrial nations, with respective increases of 6.8% and 5.8% (table 2). The components of real output with the most significant growth in the industrial countries were gross fixed investment (9.2%), consumer expenditure (3.1%), and public consumption (2.5%) (table 1). Industrial output, as measured by industrial production indices, has returned to about the 1980 level for most of the major industrial nations (table 2). Exceptions to this were industrial production in Japan and the United States; Japan&apos;s industrial production rose steadily throughout the 5-yr period and is now more than 16% above the 1980 level, and the industrial production index for the United States reached 11 1.2 (1980=100.0). Real total domestic demand grew at 8.7% in the United States, more than double the rate of Japan, which, at 4.0%, had the second-largest growth. Average demand for all industrial countries was up 5.1%. During 1984 the U.S. dollar showed great strength on international markets, contributing to large current-dollar negative net exports of goods and services and even larger negative net exports of the merchandise sector. While growing U.S. imports helped spread the benefits of the recovery, they also led to a widening of current account imbalances and growing trade tensions throughout the world.3/, 4/

Jan 1, 1985