Search Documents

By X. M. Wang

Magnetic floatation column (MFC) is a new equipment used for increasing content of iron, in which magnetite is separated in open gradient magnetic field. Simulation study was performed to investigate the separation characteristics of the separation method by analyzing the dynamic motion of magnetic particles. In this paper we compare two magnetic fields created by different magnets. The obtained simulation results give perspective in industrial design of MFC as the basis stage.

Jan 1, 2014

By M. Panayotova

Most of the quantity of the water soluble xanthates, used in mineral flotation, is consumed in the process. However, the residue amounts are water contaminants downstream the mineral processing operations and can be toxic to aquatic biota at concentrations of 1 mg/L. In order to be able to discharge water from tailing ponds to natural water bodies the concentration of xanthates has to be decreased. The present paper studies the uptake of potassium ethyl xanthate by directly modified with copper and lead ions natural zeolitic rock, without passing through zeolite transformation into homoionic form. Modified zeolite exhibits high, comparable with powdered activated carbon of chemical purity grade, capacity to remove potassium ethyl xanthate from model wastewater, with pH in the range of 7?9 and pollutant concentration in the range of 10-150 mg/L. The pollutant immobilization is fast. Both Cu and Pb modified zeolite behave as selective with respect to xanthate in the model wastewater, and Cu-modified zeolite possesses higher selectivity. The equilibrium is best described by the Freundlich equation. Keywords: xanthate, wastewater, modified zeolite

Sep 1, 2012

By N. Johnson, J. Quinteros

With the general trend across all commodities towards the treatment of lower grade ores, it is becoming increasingly important to develop efficient protocols for comprehensive mineralogical characterisation to allow the development of the most appropriate strategies for processing an ore. In the case of silver, there are more than 200 known silver bearing minerals which can make it challenging to identify them. Knowledge of the deportment of silver within an ore is one of the factors used to determine an appropriate processing strategy. Automated SEM-based tools are commonly used for mineralogical characterisation but the low-grade together with the large number of minerals that are potential hosts for silver means that often, complementary analytical tools must be used in order to properly account for the silver. The work presented in this paper is a demonstration of the approach that should be taken when identifying the deportment of silver in complex ores. Three complex, low-grade silver ores were characterised using the approach. The insights from the mineralogical characterisation were then used to inform the metallurgical testing that was undertaken. The results from the batch flotation testing clearly demonstrate the importance of understanding the mineralogy in order to select the most appropriate metallurgical processes.

Jan 1, 2014

By Kwan Ho Kim

The beneficiation study of low quality pyrophyllite is conducted to enhance the value of it by selective grinding. In mining stage, the main gangue mineral is quartz, and the content of quartz in ore has an adverse effect on the quality of pyrophyllite. Using the huge difference in hardness between quartz and pyrophyllite, the selective grinding is accomplished using stirred ball mill. As a result, a finer pyrophyllite particle can be easily separated from coarser quartz particle by simple size classification, and the content of Al2O3 of fine particle smaller than 45um increased largely. It means that the pyrophyllite particle is ground selectively compared to the quartz particle, and the quality of pyrophyllite is enhanced.

Sep 1, 2012

By S. Banisi

Thickening is the most widely applied dewatering technique in mineral processing. Thickeners are used to increase the concentration of suspension by sedimentation, accompanied by the formation of a clear liquid. As the particles get finer the thickening process encounters difficulty due to a significant change in the settling behaviour of particles. The batch settling tests of coal refuse of a coal washing plant which contained 91% particles smaller than 38µm and 0.6% coarser than 75 µm showed that the optimum feed percent solids that provided highest flux (solids handling capacity) was 4%. The flux of the pulp with the plant solids concentration (i.e., 10%) was 60% lower than that of the pulp with 4% solids. A thickener with a diameter of 22m based on the dilution of feed from solids concentration of 10% to 4% was designed. Monitoring of the thickener performance for a period of one month in the plant indicated that on average the feedrate of 25t/h (dry solids) with solids concentration of 10% could be thickened to the underflow concentration of 26.5% with a clear water overflow. It was found that the key component of the successful operation of the thickener is the dilution of the feed without which the overflow loses its clarity and the system ceases to operate under predetermined conditions. Specially designed feeding system which efficiently dissipated the energy of the incoming flow and staged flocculant addition regime are among the main contributing factors in making the design and operation of such thickener possible.

Jan 1, 2014

By Kazutoshi Haga, Batnasan Altansukh, Shirchinnamjil Nyamdelger, Atsushi Shibayama, Narankhuu Ariunbolor, Gunchin Burmaa

In this study, the authors investigated the capability of an acidic thiourea solution and silicon-organic polymers (PSTM-3c, PSTM-3T) as ion-exchange resins to recover of gold from gold-bearing ore concentrates. Firstly, elemental gold present in flotation concentrates was dissolved by leaching with a solution of nitric acid and thiourea under the optimized conditions. The best result on gold thiourea leaching was obtained under a nitric acid concentration of 2 N, thiourea concentration of 2 %, and oxidant (Fe2(SO4)3) concentration of 3 %, solid:liquid ratio (S:L) of 1:20, leaching time of 6 hours at 20 °C with a gold recovery of 93.7 % for a gold flotation (unroasted) concentrate. For the roasted gold concentrate, the dissolution of gold was 94.8% under the optimized leaching condition as nitric acid concentration of 0.5 N, thiourea concentration of 2 %, and the oxidant concentration of 1 %, S:L ratio of 1:10, leaching time of 4 hours at 50 °C. Secondly, a series of sorption tests was carried out on a pregnant leach solution containing gold complex Au[S=C(NH2)2]2+ using silicon-organic polymers (PSTM-3c and PSTM-3T), respectively. The effects of solution pH, adsorption time and temperature in the sorption process are also studied. As the results, the PSTM-3c and PSTM-3T polymers were adsorbed about 94.4 % and 95.1 % gold from the pregnant leach solutions under the optimum sorption conditions, respectively. It was found that the both PSTM-3c and PSTM-3T polymers were effective for the recovery of gold from the pregnant leach solution of thiourea. Adsorption activity of the PSTM-3c and PSTM-3T polymers was confirmed by new peaks near 1700 cm-1 in the FT-IR spectrum of the gold-adsorbed polymers, respectively.

Jan 1, 2014

By John Nell, Paul den Hoed

Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and high-titania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes. Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites. A reaction mechanism is presented; where possible, its validity is demonstrated by the support of empirical observations.

Jan 1, 2003

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

"The standard method of separation using flotation is compromised in terms of kinetics and efficiency, because of the generally slow separating differentials of fine bubbles and fine particle suspensions. A new flotation system has been developed that addresses these issues and imparts other benefits. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. Consequently the cell is designed only for the separation of the phases and not for bubble-particle contact. In the new system this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The observed result of these differential forces is the improvement of concentrate qualities by the reduction of the amount of misplaced material found in the froth. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.Prototypes of 0.65m, 1.7m and 2.2m cell diameter size have been constructed for hydrodynamic and industrial scale tests to assess the previously established computational methods for scale up of the process. The 1.7m cell has been installed and operated for cleaning of potash concentrates in Germany, at throughputs of 150 m3/hr, with extremely encouraging results. A 2.2m cell has been installed and operated in plant trials for superfine coal in South Africa. Results are presented that illustrate the effects of differential separations by comparison with conventional pneumatic and mechanical flotation techniques. Predictions of performance are provided in the contexts of the applications tested."

Jan 1, 2003

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

By Z. M. Wang

A large scale a polymetallic mine in north China is a refractory ore containing many useful com-ponents: W, Mo, Cu and Fe. Mineralogical investigation shows that the deposit is a quite complex one due to fine disseminated size and unevenly distribution of valuable, intergroth of sulphide and tungsten minerals, concurrence of scheelite and calcium minerals. Based on ore characteristic, a flowsheet is used by the floatation processing of sulfide minerals superior to scheelite. Bulk sulphide flotation is used in sulphides. Mo and Cu are floated in sequence after sulphides regrinded. Tungsten mineral is floated using combined depressant that is an effective depressant to gangue, and can improve the grade of rough tungsten concentrate. Compound depressant has high effective in removal of collector in gangue and sulphide, and tungsten is activated also. High quality of tungsten concentrate is obtained at satisfactory recovery. The test production obtains Mo concentrate with grade of 48.16%, recovery of 81.43%; W concentrate with grade of 66.47%, recovery of 78.19%; Cu concentrate with grade of 23.14%, recovery of 56.6%; Fe concentrate with grade of 67.33%. The valuable metals are recovered comprehensively and well techno-economic index is obtained. The mine enterprise profit is increased greatly.

Jan 1, 2014

By B. J. Zhang

Conventional spirals are capable of providing excellent clean coal recovery, although at a relatively high ash content. Compound spirals, which provide two stages of spiral cleaning in a single taller unit, have been commercialized in recent years to improve upon the cleaning performance obtained from conventional spirals. The present study aimed at optimizing the performance obtained from a compound spiral for cleaning especially high sulfur fine and ultrafine coal. Industrial-scale spiral units were utilized for this study in a pilot-scale facility at the Illinois Coal Development Park. A statistically designed experimental program was conducted to optimize ash and sulfur cleaning performance of the compound spiral. It was found that significant cleaning of ultrafine coal (i.e., 150 microns × 45 microns and even 45 microns × 25 microns size coal) is achievable with the compound spiral. However, operating conditions for cleaning finer coal fractions (-150 microns size coal) have to be significantly different from those used to clean coarser coal fractions (+150 microns size coal). The sulfur rejection trends were different from ash separation efficiency trends in all size fractions except 45 microns × 25 microns. The probable error (Ep) and effective specific gravity of separation (SG50c) determined for the compound spiral cleaning of the overall particle size were as low as 0.07 and 1.62, respectively. However, the bypass of a small percentage of clean coal to the tailings stream of the compound spiral, may need further adjustment of the key process parameters.

Jan 1, 2014

By Garren Edwards, van der Westhuizen. Andre

"Due to the depletion of easily treated coarser ores, more mineralogically complex ores with smaller valuable mineral grain sizes are treated, the means to liberate these minerals lies in grinding finer (Partyka & Yan, 2007). Grinding to these fine sizes is energy intensive, and using standard ball mills are energy inefficient at these sizes (P80 < 75µm). Therefore, stirred mills are becoming increasingly prevalent in the mineral processing industry. In order to optimize these mills, the effects and mechanisms of the significant variables need to be understood. This paper investigates a laboratory scale vertical stirred mill (Deswik mill) in an ultra fine grinding application of a South African platinum ore. The operating variables that are considered are stirrer speed, media size, media filling, and slurry density. The resulting grinding efficiencies are considered in two ways. Firstly, a statistical model is fitted to identify the effect of the significant variables on grinding efficiency, and secondly, the grinding efficiencies are also considered in terms of a stress energy model to determine whether this can partly explain the grinding mechanism in this mill. A factorial design of experiments was used on three levels for each variable, such that only linear interactions, second order interactions and two variable interactions are included in the statistical model. The results show that tip speed, media size, percent solids and mill filling are all significant to the grind, at differing energy inputs in the grinding process. The interaction effects of these variables are also dependent on the energy inputs. The results also found that the Kwade stress energy model is applicable to this mill and can be very useful to find the most efficient operating conditions for this system. The most energy efficient operating conditions in terms of mill speed and media size were typically somewhat below the standard operating conditions and it is expected that this is most probably done in order to increase the grinding rate, but at the expense of sacrificing some grinding efficiency."

Jan 1, 2014

By E. Guerrini, M. Maccagni, J. Nielsen

"The solution for the treatment of the EAFD has not yet been fully achieved. Some of this dust has still not found an appropriate final destination. Large consortium treatment plants are quite expensive both in terms of investment and operating cost. Meanwhile, the tolling expenses for steel production companies are becoming very important, causing them to look for alternatives. Some steel plants are looking to close their production loop by internal treatment of their dust. Some years ago, Engitec began studying the coupling of the EZINEX® Process, an ammonium chloride electrolysis to recover the zinc contained in the EAFD, with the INDUTEC® Process, a pyro process based on an induction furnace that can convert EAFD into a C.Z.O. similar to the Waelz oxide. The combination of these two processes provides an alternative to the existing treatment options and is particularly interesting for relatively small capacities. In this paper, we would like to give the latest update about these two processes and their possible integration INTRODUCTION Zinc is contained in numerous wastes and secondary raw materials that can be thought of as high zinc concentrate mines. This is a very interesting source of Zn that is typically easily exploitable. Unfortunately, only a portion of these materials are currently processed to recover the metal value, while stabilized or unstabilized landfilling is often the final destination. Pyrometallurgical processes are mainly used to convert the zinc into crude zinc oxide (CZO). The various processes are very similar and characterized by the fact that the zinc bearing materials are usually submitted to a thermal treatment [1] in which the zinc is reduced, vaporized and re-oxidized producing CZO. This material not only contains zinc oxide, but also relatively high concentrations of heavy metals. Many potential CZO sources, such as electric arc furnace dust (EAF), galvanizing ashes, brass foundry and converters fumes also contain chlorides, fluorides and alkali metals that will transfer to the CZO. The classic example is the Waelz oxide [2]. This CZO is an intermediate product that must be transformed into zinc salts or zinc metal. Until now, the conversion to zinc metal is done through two main processes: the sulphate leaching and electrowinning system and the Imperial Smelting Process (ISP). ISP is facing a crisis for technical and economic reasons that has led to the closing of most of the existing plants. In any case, before being fed to one of these two processes, the CZO must be treated to eliminate or reduce some of the contained impurities. In particular, the halides are most harmful to these processes."

Jan 1, 2018

By E. Guerrini, M. Maccagni, J. Nielsen

"The solution for the treatment of the EAFD has not yet been fully achieved. Some of this dust has still not found an appropriate final destination. Large consortium treatment plants are quite expensive both in terms of investment and operating cost. Meanwhile, the tolling expenses for steel production companies are becoming very important, causing them to look for alternatives. Some steel plants are looking to close their production loop by internal treatment of their dust. Some years ago, Engitec began studying the coupling of the EZINEX® Process, an ammonium chloride electrolysis to recover the zinc contained in the EAFD, with the INDUTEC® Process, a pyro process based on an induction furnace that can convert EAFD into a C.Z.O. similar to the Waelz oxide. The combination of these two processes provides an alternative to the existing treatment options and is particularly interesting for relatively small capacities. In this paper, we would like to give the latest update about these two processes and their possible integration INTRODUCTION Zinc is contained in numerous wastes and secondary raw materials that can be thought of as high zinc concentrate mines. This is a very interesting source of Zn that is typically easily exploitable. Unfortunately, only a portion of these materials are currently processed to recover the metal value, while stabilized or unstabilized landfilling is often the final destination. Pyrometallurgical processes are mainly used to convert the zinc into crude zinc oxide (CZO). The various processes are very similar and characterized by the fact that the zinc bearing materials are usually submitted to a thermal treatment [1] in which the zinc is reduced, vaporized and re-oxidized producing CZO. This material not only contains zinc oxide, but also relatively high concentrations of heavy metals. Many potential CZO sources, such as electric arc furnace dust (EAF), galvanizing ashes, brass foundry and converters fumes also contain chlorides, fluorides and alkali metals that will transfer to the CZO. The classic example is the Waelz oxide [2]. This CZO is an intermediate product that must be transformed into zinc salts or zinc metal. Until now, the conversion to zinc metal is done through two main processes: the sulphate leaching and electrowinning system and the Imperial Smelting Process (ISP). ISP is facing a crisis for technical and economic reasons that has led to the closing of most of the existing plants. In any case, before being fed to one of these two processes, the CZO must be treated to eliminate or reduce some of the contained impurities. In particular, the halides are most harmful to these processes."

Jan 1, 2018

By A. Vidyadhar

Printed circuit boards (PCBs) constitute a majorpart of electrical and electronic equipment containing valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, Pb, etc. The concentration of base and precious metals in PCBs is observed to be several times more than those in their respective ores. Therefore, the recycling of PCBs is necessary to recover the valuable materials. However, the ultrafine particles pose a big challenge. Removal of them is suggested prior to processing by flotation. Froth flotation is observed to be a promising technique for rejecting the plastics from the comminution product. In the present work, enrichment of ground 1.0 mm PCB powder was investigated through flotation route by varying the operating variables such as frother dosage, pulp density, air flow rate and rotational speed of the impeller. The liberation studies indicate that excellent liberation of metal values is achieved from the non-metallic constituents at -1.0 mm size and below. The particulate system is quite rich in metal value with about 23% total metal content. The non-metallic constituents such as plastics are observed to possess strong hydrophobicity while the metal particles in the pulverized mass are hydrophilic in nature. Froth flotation kinetics is studied in depth with a view to facilitate high rejection of plastics and identify optimum operating conditions for the same. A number of experiments are performed to establish the influence of the operating variables on flotation performance. The conditions for achieving higher yield of the metal-rich fraction with respect to a specified grade are discussed in the light of the experimental results. It is found that the requirement of reagents is negligible which could be a very important factor from the commercial stand point. Single-stage flotation increases the metal content from 23% to over 32% with a mass yield of around 75% and over 90% recovery of metal values. 32% of the materials in the feed could be effectively rejected in the float fraction losing less than 4% metal values. The dependence of kinetics on the process variables is also discussed. It was concluded that a high rotor speed helps in efficiently rejecting the plastics. Frother should be added to help stabilize the froth and enhance the kinetics. A moderate air flow is required while pulp density must be kept low for efficient pre-concentration. It is established that the entire -1.0 mm comminution product could be treated by flotation for generating a pre-concentrate. Keywords: printed circuit boards, recycling, froth flotation, kinetics, recovery

Sep 1, 2012

By Khoi Nguyen, Keeney. Luke

An outcome of geometallurgical mapping and modeling is the generation of continuous down hole profiles of quantitative geometallurgical attributes at assay scale. These attributes vary from traditional routine data collection methods such as assays and geotechnical logging (e.g. RQD, Fracture Frequency), to new measurements including petrophysical attributes, EQUOtip hardness data and modelled estimates of metallurgical performance indices (e.g. A*b, BMWi). Highly variable continuous geometallurgical data with high spatial resolution can make it difficult to identify spatially continuous domains. An automated method based on the well known time series analysis technique of cumulative summation (CuSum) has been developed which uses statistical analysis to identify domain boundaries in down hole profiles. A bootstrap analysis automatically identifies potential domain boundary locations with associated confidence levels and a series of t-tests determine the significance of defined populations. A hierarchical clustering algorithm is applied to results to enable data sensitivity to be taken into account. The method produces statistically significant populations and is suitable for application on either single or multiple drill hole datasets. Domains defined preserve the inherent variability of the continuous down hole data and provide a method for scaling up variability data (i.e. assay interval scale) to mine scale (i.e. bench scale, block model). A major advantage of the method is its ability to provide suitable input parameters for use in spatial modeling of non-additive and non-linear geometallurgical attributes through conditional simulation techniques.

Jan 1, 2014

By Igor Kuzymin, Isaak Maximov, Iuriy Akkerman, Galina Aksenova, Valentina Sentemova, Nataliya Trubechkova

"The Russian Federation possesses large reserves of oxidized ferruginous quartzites. These ores are currently mined together with magnetite ores and are stockpiled on account of unavailability of an efficient processing technology. This paper presents the results of investigations performed on the ores from the largest oxidized ferruginous quartzite deposit located in the Kursk Region iron-ore basin of Russia. The objective is to produce concentrate with iron content at least 66% and silica content within 5%. A processing technology was, developed under laboratory conditions, which included ore preparation, wet magnetic separation in weak and strong fields and reverse cationic flotation with addition of caustic soda, dextrin and Lilaflot 811M (alkoxy propylamine) collector from Akzo Nobel. The developed technology produced iron recovery concentrate with iron content of nearly 67%, and that of silica - 4.1%, iron recovery into concentrate being 72.6%."

Jan 1, 2014

By Dmitriy Makarov

The paper presents the modeling and analysis of oxidation of pyrite copper-zinc ore samples from the Letnee, Yaman-Kasy and Valentorskoye deposits. It is found, that the oxidized samples contain copper and zinc sulfates that are leached under the sample and water contact. It is shown, that sulfide floatability is decreased by the longer-term oxidation.We advise to improve nonferrous metals recovery by joint leaching and ultrasonic treatment of oxidized compounds. Study of the geotechnological processes of non-ferrous metal extraction, on the basis of two copper-zinc ore deposits shows, that heap leaching is of little use for the ores of the Letnee deposit. Leaching results for the Yaman-Kasy ore showed more promise.

Sep 1, 2012

By L. Muhr, Y. -T. Tang, M. -O. Simonnot, B. Laubie, R. -L. Qui, Z. Chour

"Agromining aims at recovering metals from different secondary resources with hyperaccumulating plants. These natural plants can selectively concentrate metals at very high level and can be transformed to produce commercial compounds. The classical strategy to recover metals from hyperaccumulator plants is based on hydrometallurgy. It consists of: i) burning the plant to obtain ash, which is a very rich bio-ore without organic matter, ii) transferring the target element(s) into aqueous solution by acid leaching and iii) purifying the leach liquor to obtain the target element(s) in the desired form. This method has enabled us to obtain nickel salts, nickel oxide, zinc and cadmium from different plants. However, it is not possible to apply this approach to recover rare earth elements (REEs) from the fern D. dichotoma, growing on mine tailings in South China. Actually, this plant is very rich in silicon: plant burning gives an amorphous ash, very stable despite severe leaching conditions. Therefore, the strategy has been changed and processes are currently developed to extract REEs by direct leaching of the biomass, without burning the plant. Several conditions (i.e. leaching solutions) have been investigated, showing that a good extraction yield was obtained with HNO3 0.5 N (around 84%). This yield was increased to 99% by adding a complexing resin into the leaching solution. After two-steps of elution, results have shown that is possible to recover 75% of the REEs at 81% purity.INTRODUCTION The demand of rare earth elements (REEs) (including 15 lanthanides, yttrium and scandium) has been growing sharply over the past years, because of their industrial applications. REEs are essential elements for emerging technologies, and are used for example in permanent magnets, lamp phosphors or rechargeable batteries. China is the main producer, and the market supply became tense in 2010 when this country decided to limit exports of these elements. Exploitable mineral resources, as well as REE separation capacity are concentrated in a few countries (e.g. USA, Australia, Malaysia, France), which increases the supply risk. Therefore, these elements are considered as critical raw materials (CRM) for many countries and especially for EU (Fortier and Gambogi, 2017)."

Jan 1, 2018

By J. K. Wen

The Mojiang nickel deposit is situated in Mojiang county, yunnan province, a tropical area in the southwestern China. The known geological resource (measured and inferred) includes 4 million tons of nickel sulphide ore at an average grade of 0.50% Ni and 0.34% As. Nickel minerals are mainly gersdorffite (NiAsS), millerite(NiS), morenosite (NiSO4?7H2O), and more than 50% nickel minerals is gersdorffite which contains arsenic. Pyrite is the dominant sulfide mineral, 22% in the ore and part of nickel minerals are locked in pyrite. It is difficult to attain the nickel concentrate quality allowed by a smelter and the acceptable nickel recovery through flotation due to the high arsenic in the ore and the nickel minerals locked in pyrite. The shake flask tests and column tests for nickel recovery from the Mojiang nickel sulfide ore had been finished by the end of 2003. The column bioleaching tests were carried out using the columns with diameter of 120 mm and height of 1200 mm, and 70% of nickel dissolution was attained in 300 days. A 10,000t pilot test heap was built in the Mojiang Nickel Mine by June 2003. The ore used in the test heap was supplied from the underground mine and was crushed to -20 mm before being feeding to the test heap, which is 4~5 m high, 30 m wide and 50 m long. The naturally adapted mesophile and moderate thermophile have been inoculated into the leaching pile by June 2003. The operating temperature in the heap ranges from 38? to 55?, varying with season. 30% of nickel dissolution was achieved in 3 months and the typical pregnant leach so-lution (PLS) contains 2~3 g/L Ni and 20~30 g/L Fe. The Ni sulfide which was produced by us-ing Na2S 10 t/t?Ni contains 16%~20% Ni and Ni recovery was 98%. 70% of Ni dissolution is expected in 12 months. The test heap was scaled up to 60,000 t of ore per year by mid of 2005. In this paper metallurgical studies and performance of the pilot test heap will be described. The results of mineralogy, shake flask tests and column tests on bioleaching of the nickel sulfide ore are reviewed. The key test heap operation parameters, the performance of bio-heap leahing-Na2S precipitation, ferrous oxidation-ferric precipitation-Na2CO3 precipitation, bacteria in the pile, water and acid balance, effluent disposal, capital and operation costs are also discussed.

Jan 1, 2014