Search Documents

Energy Savings and Technology Comparison Using Small Grinding Media Considering the complexity of minerals, the need for finer grinding is increasing along with the energy cost. However, energy is increasing exponentially when grinding finer with conventional grinding balls. The use of small grinding media represents the best potential to improve energy efficiency. Today, it is possible to use grinding media as small as 1 mm. How do they perform in industrial grinding mills? The use of small grinding media (5 - 12 mm), called Millpebs, in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, energy savings vary from 10 per cent to 40 per cent compared to 25 mm media. A regrind ball mill with a mix of small grinding media can be as energy efficient as an Isa Mill charged with 2.5 and 3.5 mm beads. In vertical stirred mills, energy savings vary from 30 per cent to 60 per cent. To carry out the same final grind, a vertical stirred mill with Millpebs will consume at least 60 per cent less energy than a ball mill using 25 mm grinding media. More potential savings were identified. To achieve those improvements, some operating conditions must be met: 1) feed size should be less than 250 ¦m; 2) the pulp must be fluid enough; 3) finally, the slurry linear velocity should not be excessive. This paper talks about all those industrial results improvement and operating conditions.

Sep 13, 2010

A model has been developed as part of the AMIRA P420 Gold Processing Technology Project to simulate the recovery of gold by centrifugal gravity devices. The model (which is available online) uses the simulation methodology developed by Laplante et al (1995) to predict gravity recoverable gold (GRG) recovery under varying operating conditions and circuit configurations. In addition to predicting GRG recovery, the model also predicts the GRG content and size distribution of the cyclone overflow and underflow. The predicted overflow GRG content and size distribution can be used as inputs for a leaching model in which size dependent leaching rates are applied for each size class of GRG and non-gravity recoverable gold (non-GRG) in the cyclone overflow, allowing size-by-size leach recoveries to be determined for GRG and non-GRG. The application of the gravity model and leaching model are demonstrated using a case study. The simulated gravity recovery and leaching performance showed excellent agreement with the measured values. The developed models can be used to assess the sensitivity of gravity gold and leach recoveries to varying feed GRG content, GRG size distribution, gravity circuit feed rate, classifier performance and leach residence time. The described methods can be used to optimise new and existing gravity and leaching circuits.

Aug 1, 2010

Electro-Flotation Research on Fine Cassiterite

Sep 13, 2010

Minerals processing needs a step change in energy efficiency. While the search for new technology breakthroughs is important, huge gains are still available by better using existing research outcomes. This potential remains untapped due to a combination of organisational 'silos', inappropriate performance measurement, and poor science in some areas. It is time to see the elephant in the mill.

Sep 13, 2010

The Influence of Particle Shape in Rock Fracture

Sep 13, 2010

A Process for the Flotation of Chrysocolla

Sep 13, 2010

Iron Concentrate Synthesised from Waste Ferrous Sulfate Produced in Titanium White Preparation

Sep 13, 2010

Possibilities for Flotation Acoustics Monitoring - A Review

Sep 13, 2010

Removal of Thiocyanate from Solutions by Precipitation

Sep 13, 2010

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

Understanding multiphase particulate systems is essential for the further advancement of mineral processing technology. Characterisation, analysis, and simulation of these complex systems provide a fundamental basis for the development of improved mineral processing technology. One of the more recent tools that can be used to help provide a foundation for improved mineral processing technology is high resolution cone beam X-ray micro computed tomography (CT). During the past ten years point-projection X-ray micro CT systems have been used for 3D visualisation and quantitative analysis of multiphase particulate systems. Analysis of packed particle beds containing as many as 30 000 particles can be accomplished in less than three hours with special software to establish the 3D characteristics of each particle in the population and the spatial organisation of the packed particle bed. Now, due to advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. The development of software tools for the 3D characterisation, analysis, and simulation of packed particle beds using high resolution X-ray micro tomography (HRXMT) is discussed including examples of application in the areas of comminution (particle damage and preferential grain boundary fracture), exposure/liberation analysis (liberation-limited separation efficiency, including coal washability), and filtration/heap leaching (pore network structure of packed particle beds and simulated flow using the LB method of computational fluid dynamics).

Sep 13, 2010

SAG Mill Grinding Design Versus Geometallurgy - Getting it Right for Competent Ores Smarter processing for the future, in the area of SAG mill design involves accurate grinding test data, completing final mill design in less than three months, and at a cost of less than US$80 000. More detailed variability testing on the other hand takes longer, is more expensive, and is used for throughput optimisation for an existing or newly purchased mill. This paper shows that SAGDesignTM testing is excellent for new SAG plant design due to relatively low cost per test and the ability to do more testing for a limited budget on larger projects. It also briefly examines a way to develop proper geometallurgical ore hardness information on every block in the mine model, from the more detailed analysis data.

Sep 13, 2010

Recycling and Recovering Fine Particles from Auto Shredding Residue (ASR/SR) to Conserve Raw Materials and Protect Environment

Sep 13, 2010

An Integrated Study of Bubble-Particle Attachment Mechanisms

Sep 13, 2010

Comparison of Industrial Cyanide Destruction Processes

Sep 13, 2010

Economic Sustainable Power for Mineral Processing

Sep 13, 2010

Recovery Efficiency Study on Ilesha Placer Gold Ore by Flotation Using Locally-Sourced Frothers and Collectors

Sep 13, 2010

Improving the Sustainability of Primary Metal Production - The Need for a Life Cycle Approach

Sep 13, 2010

Research and Tests on Improving the Technology of Enrichment of the Copper-Molybdenum Ore

Sep 13, 2010

Acoustic Emission Monitoring of Froth Flotation

Sep 13, 2010