Search Documents

By Charles R. Keyes

A COMPLETE transformation has taken place in the boras industry during the year 1908. A most remarkable factor in this radical change in method of producing the crude borates has been its removal from the realm of industrial chemistry to the field of mining. With the development of extensive deposits of borate-minerals interstratified in thick sequences of Tertiary clays and sands, their winning becomes a strictly mining-enterprise, of the same kind and of the same certainty as the digging of coal or iron-ore. The major supply of the world's production of commercial borax now comes from the United States. While formerly all of the boric salts of commerce were laboriously extracted from the waters of saline lakes of the arid regions, or from the bottom-salts of desiccated ponds, it later was largely slowly leached from ancient desert shales and clays. During these periods the borax industry was a very hazardous and expensive vocation.

Oct 1, 1909

By Dale A. Zuck

Recovery of aluminum metal from drosses? is a major factor in the recyclability success story enjoyed by the United States aluminum industry. Today's modern dross processor uses the latest technology to maximize metal recovery at the lowest cost while complying with all environmental laws and regulations. Most dross processors, however, pay little attention to the resulting saltcake, the end residual of dross recyCling, and rely on landfills for .disposition of this material.. The alternative is to recycle the saltcake, but the success of this technology is dependent on the development of reliable outlets for each of the saltcake constituents. This paper discusses the evolution of an aluminum dross oxide processing technology that ,produces an economically attractive source of alumina for the production of portland cement.

Jan 1, 1995

By J. O. Merritt

The primary objective of this research program was to recommend ranges of minimum luminance for safety in underground metal and nonmetal mining. Visual tasks critical to safety were identified and rank-ordered. Realistic, full-scale, dynamic task simulations encompassing the most important visual components of the critical tasks were installed in a large simulated workspace. Five trained observers performed the six simulated mining tasks under varying levels of luminance. Over 13,000 measurements of visual task performance were used in developing minimum luminance recommendations for the on-foot underground worker and the mobile equipment operator.

Jan 1, 1983

By O. H. Metzger

This is one of a series of papers being published by the Bureau of Mines on mining areas and districts in the Western states. It describes mining and milling practices in the vicinity of Wickenburg in Maricopa and Yavapai Counties, Ariz. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of the operators of the mines visited. Reports of geologists and engineers who previously visited the area were drawn upon freely. Individual acknowledgments are made in the text.

Jan 1, 1938

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I -of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By Jr. Boyle

This report analyzes the availability of chromium in the form of ferroalloy products (high-carbon and low-carbon ferrochromium and ferrochromium-silicon) and chromite products (metallurgical, chemical, refractory, and foundry sands) in market economy countries (MEC's). A total of 873.5 Mmt of in situ material, containing 202.5 Mmt of chromium, in 10 MEC countries was analyzed for availability as of the January 1989 study date. Extraction and beneficiation of this in situ material would result in 475.4 Mmt of marketable chromite products. As analyzed, 288.5 Mmt of these chromite products would be available for export or for internal chemical and refractory use and 186.9 Mmt would be smelted in-country to produce 74.3 Mmt of high-carbon ferrochromium, 3.9 Mmt of low-carbon ferrochromium, and 2.0 Mmt of ferrochromium-silicon, all available for export. A network flow model, which includes centrally planned economy countries (CPEC's), was also constructed to analyze world chromium supply and demand interactions for the period 1986 through 1994 and to address a hypothetical North American embargo on direct imports of all South African chromium products beginning in mid-1990. The model shows capacity constraints developing in the MEC high-carbon ferro chromium industry in 1987 and a possible subsequent overreaction by the industry in terms of new capacity additions. The results suggest that sufficient chromium is available to North America should an embargo on direct imports from South Africa be imposed by its governments. However, the effect on export revenues in South Africa is relatively small, and timely increases to world ferrochromium, chemical chromite, and foundry sand chromite capacities would be required.

Jan 1, 1993

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

By James F. Kvitkovich, George V. Weisdack

Editor’s note: This is the second part of a two-part series on longwall mining in the United States. Part one was published in the December 2005 issue of ME (pp. 21-26). It provided a history of longwall coal mining in the United States. It also discussed the technology involved in the productivity gains and operational improvements. Boyd anticipates that U.S. coal production will increase by 61 Mt (67 million st) (6 percent) from 2004 to 2010. A combination of higher surface and underground mine production will be required to meet the projected market demand. Boyd’s projections of coal production by major mining methods are shown in Table 1.

Jan 1, 2006

By A. L. Toenges, F. A. Jones, J. N. Sxudder, E. R. Maize

"INTRODUCTION This report is the second of a series of studies of analysis of energy requirements and characteristics of various machines used in the production of coal in underground mines and the losses in distribution of energy to these machines. The test equipment used in these studies is described in Report of Investigations 3615. 7/ The preliminary study data and results of tests made on various types of mechanical-leading cutting, and transporting equipment at two mines. This report is analysis of the energy requirements of the energy requirements of the underground equipment of a third mine. An analysis of the use of energy and its distribution usually requires in a saving in energy consumption and the reduction of hazards. The distribution system should be designed to supply energy effectively and study for the efficient operation of all machines."

Feb 1, 1943

By Gus Van Weert, Peter Kondos

"Ore sorting has been quite successful in providing a separation means in the rock size range of 1 to 6 inches; a range where mineral dressers do not have many options. The industrial minerals and recycling worlds have embraced this technology. However, ore sorting has not found wide application in the base or precious metals mining industry. One reason for this is thought to be the reliance of most sensors on rock surface characteristics, not very useful in case of sulphides, non-existing in case of gold. Microwave heating, however, is specific for sulphides and graphite (or carbonaceous matter) embedded in the rocks; washing or even drying does not appear necessary. Separation can be done afterwards by already existing ore sorting technology using infrared sensors. Test results on six Nevada gold ore samples are presented in detail. Some simple test procedures are also presented for those wishing to explore the microwave potential of sulphide sorting in their own operations.INTRODUCTIONMineral processing in the base metals industry most often involves upgrading of the ore, concentrating the valuable mineral fraction by classic methods, such as flotation. Since the liberation of minerals in the ore occurs mostly at or below the 100 micron level, the industry has been living with fault lines, so to speak, between blast hole spacing (10,000 mm), run-of-mine ore size (100 mm) and beneficiation size (0.1 – 0.01 mm). The acceptance of ore sorting will inevitably lead to the revisiting of the following questions: “Exactly how much below ore grade rock ends up in the mill because the geologists or the miners cannot define the resource boundaries more precisely? How can the economics of dilution be improved? How many ore grade rocks are lost with the overburden?”"

Jan 1, 2007

By R. Greenwood

The advent of the space age and its promise of interplanetary flight has prompted new ideas for propulsion systems that will allow maximum energy with minimum fuel weight. The use of cesium as the source of energy for such rocket flights has been found desirable. Theoretical efficiency of a rocket fuel is measured in terms of specific impulse, defined as the number of pounds of thrust per pound of propellant consumed per second. Specific impulse is usually expressed in seconds (the number of seconds for which one pound of fuel would produce one pound of thrust) although it is really a measure of total energy, not of power. The most sophisticated chemical fuels have a specific impulse of 300 to 400 sec; liquid hydrogen heated by nuclear reactor has a specific impulse of 1000 to 1200 sec. Specific impulses as high as 20,000 sec, however, are theoretically attainable with the ion rocket, in which free cesium ions are accelerated across a voltage drop and ejected at high velocity.' Characteristics of the system have been sketched by Boden.2 The desirable properties of an ion propellant are: 1) low ionization potential, 2) low boiling point, and 3) high atomic weight. Alkali metals best fulfill these requirements, and Table I indicates the superiority of cesium. The use of heavy complex ions such as UCl3 is ruled out by their instability and other disadvantages.' Despite its enormous superiority in specific impulse, the ion rocket is inherently low-powered, capable of very small acceleration. Application of ion propulsion will be limited to large rockets and spaceships on missions requiring powered flight for weeks or months and employing a separate chemical propulsion system for escape from the earth's atmosphere where power requirements are large but of brief duration. For example, Kraemer and Larson3 considered the case of an unmanned 25,000-lb pay-load placed in a 300-mile orbit by chemical rockets, proceeding thence by ion propulsion to the vicinity of Mars, where it would go into orbit once again. Calculations provide for 8500 lb of cesium for such a voyage. The question of whether such quantities of cesium will be readily available to the space program does not appear to have been considered by geologists and mining engineers. Present Production and Uses Literature on industrial applications of cesium is scanty. The metal is used in scintillation counters, photocells, infra-red detection devices, and as a "getter" in low-voltage vacuum tubes. Production is sporadic and total figures are not published, but the annual consumption is measured in pounds rather than in tons. The few pollucite deposits known, small as they are, can easily supply the present limited demand for gram or pound lots of cesium. Until recently the price of cesium was $2 to $4 per gram, but according to Chemical Engineering, cesium salts are now available at $13 to $27.50 per lb. Geochemical Distribution As a large alkali ion, the cesium ion accompanies potassium in geological processes and tends to be concentrated in the latest crystallizing fractions of potassium minerals in much the same manner as rubidium. Most of the cesium in igneous rocks, therefore, is in the micas and potash feldspars of granites, and especially in granitic pegmatites. The cesium content rises markedly in the micas of the late by-drothermal replacement stage in complex pegmatite~.' Typically, cesium is only 0.5 to 0.01 times as abundant as rubidium in potassium minerals. Rb', with a radius of 1.47 A, is close enough in size to K' (1.33 A) so that rubidium forms no minerals of its own. Cs+ is so large (1.67 A) that only small concentrations can be taken up in potassium minerals; when cesium is present in solution in larger concentration it forms the mineral pollucite, Cs3-Na2A17Si17O48.3H2O, which is known only in pegmatites. In the weathering of igneous rocks, cesium is dissolved, carried to the ocean, and apparently in-

Jan 1, 1961

By G. Budge

In the extractive industry the term ‘continuous improvement’ (CI) usually means procurement of the latest state of the art equipment. This is generally perceived as the only way to add further value to the supply chain, with the driving philosophy of increased tonnage to dilute operational costs. However, not all market places can facilitate this approach. RJB lives in a fiercely competitive market and has targeted the standard efficiency drivers of rationalisation and stock management with a vengeance; and also operate CMMS (Computer Maintenance Management System), RCM (Routine Condition Monitoring)and CBM (Condition Based Maintenance) methodologies. Ultimately though, these systems are only as good as the people who operate and manage them and to add further value without procurement, people must be re-introduced back into the operation. Through TPM (Total Productive Mining), that is what RJB have set out to do.

Jan 1, 2001

By Lloyd A. Morley

This seven-chapter document is the first volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. After a short introductory chapter, Chapter 2 discusses the history of electrical use in mining and introduces "typical" mine- power-system arrangements. Chapter 3, 4, and 5 supply basic information on electrical theory, circuit analysis, and motors. Next, the Grounding and Distribution Chapters detail unique aspects of mine power systems. Elements of surface and underground use are included in all these chapters. An index concludes Volume I and is cross-referenced to both report volumes.

Jan 1, 1982

By P Ring, B Cooper, C Carr, G Laing

The Nova Ni-Cu-Co Operation, located in the Fraser Range of Western Australia, commenced commercial production in July 2017 only five years after discovery. Owned by Independence Group NL (IGO), the operation has successfully ramped up over an accelerated schedule and currently deploying leading technologies. This paper begins with a description of the Nova Operation, and its journey to achieve full production in such a short time frame. It includes discussions on development and production design, selection of fixed plant infrastructure, and the features challenges of running a low-pressure primary ventilation circuit. The paper also discusses key technologies that have improved overall safety for the underground workforce, and improved operational efficiencies. Investigations continue into the implementation of further technological applications for safety and productivity enhancements. This paper also discusses the findings from a study into transitioning from a diesel to an all-electric underground mining fleet, based on a review of Nova if it were to be developed today with the current EV offerings. The study indicates compelling savings will be available to future mines when considering development design, project schedule, capital outlay and operational savings, and the ‘next Nova’ is expected to be all electric.

Mar 15, 2021

By D. du Plessis, R. Stobbs

The Canadian Clean Power Coalition (CCPC) was created in 2001 to protect and enhance Canada’s vast coal and other carbon-based resource wealth, and to ensure that environmental public policy decisions recognize that these resources are a Canadian asset, not an environmental liability. To achieve its mandate, CCPC has undertaken to demonstrate technologies for use in new coal-fired power plants to control air emissions including carbon dioxide (CO2), nitrogen oxides (NOx), sulphur dioxides (SOx), mercury (Hg), and particulates (PM). The first phase of the demonstration project assessed three existing technologies for coal-fired power plants that reduce all emissions, including CO2, to levels equivalent to or below that of gas-fired power plants. The technologies considered in this phase included integrated gasification combined cycle (IGCC), ‘oxyfuel’ combustion, and amine scrubbing of pulverized coal. These technologies were evaluated with three coal types: Eastern bituminous, western sub-bituminous, and lignite coals. This paper presents the studies, conclusions concerning the capital and operating costs of these technologies, the cost of electricity produced (with CO2 removed), and the cost per tonne of CO2 avoided. It also discusses the potential for using captured CO2 for enhanced oil recovery, and possible technology enhancements for improving the competitiveness of gasification of low-rank western Canadian coals. The second ongoing phase of CCPC’s work includes the design and construction of a commercial-scale plant to demonstrate the feasibility of integrated gas combined cycle (IGCC) and/or polygeneration technologies and the potential for using the CO2 generated for enhanced recovery of conventional oil.

Jan 1, 2006

By Tim O’Neil

Nearly 4,800 mining professionals and exhibitors occupying 580 booths attended the 2000 SME Annual Meeting and Exhibit, Feb. 28-March 1, in Salt Lake City, UT. The technical program included80 sessions and four specialty symposia: bulk material handling, control 2000, minor elements 2000 and plant operaters. Meeting highlights included the keynote session. Executive shared their perspectives on pivotal issues and approaches to address the challenges of the new millennium. SME has begun planning for its 2001 Annual Meeting, Feb. 26-28, in Denver, CO. The meeting carries the theme “2001 — A Mining Odyssey.” A call for papers has been issued and exhibit space is 80% reserved. For information, visit SME’s website, www.sme-net.org. Or write Box 625002, Littleton, CO 80162-5002,ph 800 763 3132 or 303 973 9550, fax 303 979 3461, or email meetings@smenet.org.

Jan 1, 2000

By Madan M. Singh

This section is unique to the Handbook in that it is the only section that deals with underground excavations for nonmining purposes. The editors were of the opinion that the section should be incorporated because the subject matter covered by the chapters is closely related to mining, and many mining engineers are currently involved in these activities. As we enter the decade of the 1990s activities in this category will increase, enhancing the relevance and utility of the material discussed. As the population increases, especially in metropolitan areas, the necessity to go underground will be greater. At the present time, not only are subsurface shopping malls and pedways connecting buildings becoming commonplace, but structures as diverse as the Civil and Mining Engineering Building on the University of Minnesota campus, a road-and-fleet maintenance facility in Multnomah County, OR, and even an ice cream parlor (Dairy Queen) in northern Wisconsin have been constructed underground. Placing utilities below the surface has numerous advantages and is now customary. Rapid transit and highways through tunnels in urban areas have been the norm for many years, but subterranean stormwater reservoirs, power plants, industrial warehouses, and food storage silos are relatively new innovations. The philosophy of underground defense installations is ancient, but their requirements and designs have trans-formed radically as technology advances. The use of under-ground space for disposition of wastes is modern, since it is recently that environmental concerns and waste disposal costs have assumed increased significance.

Jan 1, 2008

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

By C. Dirscherl, M. Combes

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications.INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment)"

Jan 1, 2014

By Henk van der Bijl, Sean Rogers, Eugene Sidorski, Alan Carpenter

The electrode column is the heart of the submerged arc furnace. Superior electrode performance provides improved furnace performance. This paper describes the main features of the electrode column that delivers superior performance in furnaces worldwide, developed by Pyromet. Pyromet?s electrode comprises the compact slipping device, lower electrode assembly, upper and lower mantles, self-adjusting electrode seal, paste heaters, and Pyromet?s patented innovative electrode breakage detection and length determination system. Pyromet?s slipping device features compact interlocking clamping rings, incorporating fail-safe spring-loaded design. The interlocked clamping rings distribute the clamping force over a larger area of the electrode casing, preventing damage. The slipping device assembly features a low maintenance modular design that allows rapid slipping cycle times, back slipping, and compatibility with Pyromet?s electrode breakage detection and length determination system. Pyromet?s lower electrode assembly consists of the contact shoes, pressure bellows, pressure ring and heat shields. The contact shoes and pressure ring are designed for long, trouble free operation whilst the pressure bellow configuration equalise contact pressure and current distribution. Furthermore, the contact shoes incorporate a self cleaning feature, ensuring optimum electrical contact. The segmented design offers easy maintenance. Pyromet?s clients experience less down time due to longer component life. Pyromet?s remote adjusted electrode seal assembly reduces the rope seal working temperature, increasing rope life. The self compensating rope seal clamping force ensures an effective seal as the rope wears. Pyromet?s electrode breakage detection and length determination system detects electrode breaks utilising Pyromet?s electrode holder and data processing system. The length measurement system controls electrode length, eliminating the occurrence of short electrodes. The length measurement system furthermore eliminates the need for manual electrode length measurement, reducing associated production losses during furnace burn downs.

Jan 1, 2007