Search Documents

By Leith Sharp

I was confronted with a profound dilemma as an undergraduate engineering student at the University of New South Wales in Australia in 1992. I had been taught that our planetary life-support systems were in a state of alarming decline by an institution that operated as if what the faculty was teaching was irrelevant. Lights were left on in empty overcooled classrooms, recycling bins were nonexistent, lawns were maintained using pesticides and herbicides, diesel trucks spewed fumes as they passed on their way to drop off chlorine-bleached virgin paper. This disconnect was very alarming to me. While it was obvious that universities should play a leading role in teaching and researching sustainability issues, I wondered how it could be possible to make widespread institutional changes to meet the demands of environmental sustainability when it was not even being done in the very university sector where these ideas were being promulgated. If universities would not change, then who can and who will, I wondered? To a growing number of people, the idea of teaching sustainability without demonstrating it is highly problematic. It is also widely believed that the ability of the higher education sector to reform its own practices is an important indicator of humankind?s ability to address the global environmental imperative across all sectors of society. These sentiments have helped fuel what is now referred to as the campus sustainability movement, a movement dedicated to transforming our campuses into living laboratories for the demonstration and practice of environmental sustainability.

Jan 1, 2010

By B. Sivarama Sarma, Biswabikash Rout

"Seepage control has to be achieved with plastic concrete cut-off diaphragm walls in dam structures. Materials selected for construction of cut-off walls must be durable, impermeable and have stiffness comparable to the surrounding soil.Plastic concrete provides a feasible and economical solution for construction of durable and impermeable cut off walls for dam structures. Plastic concrete wall should not be understood as a concrete wall with similar mechanical properties of concrete used in buildings, piles and spillways sections. Though it consists of the same materials as those of conventional concrete it has the major differences in end product due to predominant addition of bentonite slurry in the mix with very high water cement ratio. This makes the hardened concrete with very low compressive strength less than 5MPa and high failure deformations after the peak load.This technical paper examines a case study, the typical specifications on demand for construction and the issues corresponding to misunderstanding of the material as a structural grade concrete material. Conclusions were drawn based on a few project site quality data and trial mix experimental data. The anomalies in specifications on demand for construction of curtain wall in a dam structure were removed with modifications.INTRODUCTIONDiaphragm walls which are constructed in trenches made of plastic concrete basically serve the function of seepage control under confined measures. They should have the ability to sustain and undergo large plastic strains as compared to conventional concrete. The three basic mechanical properties of plastic concrete cut-off walls are to have least permeability, minimum strength to retain its shape and ability to undergo large deformations under confined loading conditions. The constituents of plastic concrete are cement, bentonite, coarse and fine aggregates, chemical additives to improve flow of concrete and sometimes to retard the setting time and water."

Jan 1, 2017

By L. Douglas Smoot

This research program was a theoretical and experimental study to improve understanding of the mechanisms of flame extinguishment in methane-coal dust-air-suppressant mixtures. This final report is a summary of work conducted during this grant, sponsored by the Bureau of Mines. Work under this new grant closely followed a recently completed contract for the Bureau of Mines that was conducted at this laboratory, and results of the earlier contract are also summarized in this report, as required in the grant work statement. The experimental effort was concentrated on supplementing the limited data available to describe laminar flames in methane-coal-air-suppressant mixtures. The theoretical effort was devoted to developing a comprehensive model that could be used to explain and extrapolate the experimental data. Selected for study were the following flames: Methane-air; methane-air plus KHCO , KNO3, K C204, KBr, Al203 or Monnex; methane-coal dust-air; coal dust-air with size, volatiles content, and concentration as variables, and coal dust-air plus KHCO3, KN03, KBr, NaCl or CaC03.

Jan 1, 1978

By Austin Metz, Kevin Stanton, Ramin Motamed

"A recent study calibrated Load and Resistance Factor Design (LRFD) resistance factors for local soil conditions in the Las Vegas Valley. As a part of this calibration, an extensive database of drilled shaft load tests and associated subsurface soil information were collected and compiled. This database, deemed the Nevada Department of Transportation Deep Foundation Load Test Database or NDFLTD, was designed with the presentation of load test data, the subsurface soil conditions, and the spatial distribution of the data in mind. In addition, the NDFLTD was developed in a way that allows additional data to be added as it becomes available. As such, the rules of database normalization were followed to allow for additional and different types of data to be added to the database and reports. Microsoft Access was chosen to present the data because it is easily accessible to anyone with Microsoft office software, it has a quick learning curve, and it has the ability to present a relational database. The largest obstacle faced when creating the NDFLTD was normalizing the data used in the LRFD calibration, with the goal of reaching the 5th normal form.INTRODUCTIONLRFD is based on statistical performance of engineering components, as opposed to the more traditional Allowable Strength Design (ASD), which divides the strength of a component by a safety factor. Calibration of resistance factors for LRFD requires a robust statistical analysis of past performance. For drilled shafts this requires a database of full scale load tests (Abu-Hejleh et al. 2014). The FHWA developed the largest US based deep foundation load test database, deemed the DFLTD, collecting data from 1985 to 2003 when funds ran out (Abu-Hejleh et al. 2014). Recently, the DFLTD has been updated to modern standards (Petek et al. 2016). In October of 2007, the FHWA mandated state department of transportations (DOTs) to follow AAHSTO LRFD guidelines for their highway foundation designs (Abu-Hejleh et al. 2014). Since then multiple state DOTs have developed their own, region specific deep foundation load test databases. Florida has a long history of developing databases for deep foundation LRFD resistance factor calibration, with the two main databases being the FL database, and The Deep Foundations Database (Abu-Hejleh et al. 2014). Iowa developed a Microsoft Access based database in 2014 (Garder et al. 2014). Oregon developed a database compiling pertinent data from the DFLTD, Florida DOT’s Deep Foundation Database, as well as from other databases (Smith et al. 2011). Illinois developed the “International Database” for static and dynamic reliability based calibration (Long et al. 2009). Louisiana developed a database for LRFD Calibration of driven piles in 2009 (Abu-Farsakh et al. 2009). The California Department of Transportation has its own internal foundation database, which is housed within the Foundation Testing Branch archive (Smith et al. 2011). In 2016, the Nevada Department of Transportation (NDOT) presented its own LRFD calibration for the Las Vegas Valley (Stanton et al. 2017), and the NDFLTD was developed as a part of that project (Motamed et al. 2016)."

Jan 1, 2017

By O. F. Ochonogor

Laser metal deposition (LMD) is an additive manufacturing technique whereby a stream of metal powder is consolidated by a focused laser beam on the surface of a substrate or engineering component. The interaction zone between the laser beam and powder particles is scanned superficially, generating tracks of deposited material. The tracks are overlapped in a deposition strategy in accordance with slices of a CAD model. Successive layers of material are built up to fabricate a near net shape part. In this work, the technique is used to fabricate metal matrix composites (MMCs) by using an elementally blended feedstock combining metal and ceramic powders in the melt pool, which melt and solidify to create the required morphology. Ti6Al4V + TiC MMCs were produced with 10, 20, and 30 vol.% reinforcing ceramic, and Zr + TiC MMCs were fabricated with 10, 20, and 30 vol.% TiC. The deposited thin walls were analysed using optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and indentation testing. In both systems, the analysis revealed the presence of partially melted TiC particles embedded in the metal matrix along with fine dendrites of re-solidified ceramic. The dendritic structures in the Ti-based composites were confirmed as TiC, whereas in the Zr-based composite the Zr metal reacts with theTiC to form ZrC, leaving Ti in solid solution. Both the MMCs show an increase in microhardness with increasing ceramic (carbide)content, reaching a peak HV0.1 value of 500 in the Zr- based MMC and HV0.1 of 550 in the Ti based MMC.

Jan 1, 2012

By Richard L. Gordon

Coal supply analysis has since about 1973 become a major activity of many scholars and consulting firms. The present paper is an effort to explain in as nontechnical fashion as possible the state of the art and what implications, if any, the research has for those actually engaged in producing coal or regulating the industry. l The discussion stresses the coal supply side of the models and makes limited comments about other elements in the analysis. To orient the appraisal, it is desirable to recall the features of coal supply that an adequate model should capture. The first considerations are the locational aspects of the industry. Transportation costs can, in some cases, exceed the production costs of coal, and thus any adequate model must incorporate a treatment of the economics of transporting coal from one location to another. A second major issue is that of the heterogeneity of coal; models should treat as well as possible such key differences among coals as their Btu and sulfur content. Third, we recognize that, with given technology and labor, capital, and supply costs, an expansion of the supply of a given type of coal in a specific region will occur only if prices rise. This is the familiar proposition of textbook economics that supply is an increasing function of price. Finally, over time, changes in technology, input cost, and depletion interact to cause changes in the price of given amounts of coal. Economics represents the net effect of this process by a shift over time in the supply curve. During the 1950s and 1960s, the trend was to reduce the production costs of a given output; subsequently costs rose sharply.

Jan 1, 1977

By A. More, J. M. Míguez, J. Bullón

In 2000 Ferroatlantica started a project with the aim to develop a new casting machine for silicon and other ferroalloys. Until now, it has been cast more than 25.000 tons of silicon for the chemical and metallurgical market. This system has improved the process yield, productivity and product quality which place?s Ferroatlantica at the top of technology development in this field. After the first presentation of the Ferroatlantica?s casting machine at Infacon X, we would like to show the improvements in the control which have permitted us to increase the lifetime of the copper and to obtain, at the end of the machine, the right product size for the customer avoiding the current necessity of crushing and sizing the lumpy metal. Furthermore, we have improved the system in relation to the obtaining of smaller granulometries at the end of casting machine. Not only is this kind of machine cost competitive for special silicon applications but also for other normal ferroalloys with different specifications of size and thickness.

Jan 1, 2007

By R. R. Lowery

This project was proposed to provide information on the hazards associated with arc melting of thorium. A general air-sampling analysis was made to determine the separation, concentration, and distribution of thorium daughter (decay) products throughout arc melting, machining, and forging processes of a thorium handling facility. The value of well coordinated health physics program is stressed in connection with potential health hazards and personnel protection. Building, equipment, and exhaust ventilation requirements for such a facility are discussed. Special handling methods are described for thorium. INTRODUCTION The Bureau of Mines at the Albany Metallurgy Research Center has been involved in handling the naturally radioactive metals, uranium and thorium, for several years. Cooperative work for the Atomic Energy Commission has been carried out with thorium metal, and as a result the concerned laboratories of the Center have accumulated experience on the hazards associated with this metal. This report details the radioactive hazards arising from the arc melting, machining, and forging of thorium.

Jan 1, 1962

The 109th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 16 August 2006. Special General Meeting A Special General Meeting to consider the changes to the Constitution was held immediately prior to the AGM. 1. Purpose In order for the SAIMM to remain relevant and ensure maximum value to all members, Council propose three changes to the Constitution. 2. Background Three changes to the Constitution were proposed by the Council on 21 July 2006. These changes now have to be approved by means of a ballot at a Special General Meeting. These three proposed changes are discussed briefly below:

Jan 1, 2006

By D S. Clarke, K B. Sporli

The Thames Goldfi.eld has been a major gold resource in the west of the Coromandel Peninsula, New Zealand, with the Waiotahi quartz vein system forming a large part of the field. Mineralisation is hosted by hydrothermally altered Miocene andesitic volcanic rocks. Both massive columnar-jointed and fragmental volcanic rocks are present. The vein system is dominated by the steeply dipping NE striking Waiotahi-Cambria vein, and associated splays. Hydrothermal alteration increases in intensity from isolated blocks of propylitic altered andesitic material, into the intensely clay altered equivalent. Low rank propylitic alteration is typified by chlorite, calcite and pyrite, with local illite or epidote. Clay alteration is characterised by illite, quartz, kaolinite and pyrite. While broadly forming halos around veining, intense clay alteration also occurs in strongly jointed portions of the hostrock.   Vein textures and the intense illitic clay alteration at Thames are similar to those in some of the other epithermal gold deposits of the Coromandel Volcanic zone, and in deposits of the Philippines, all related to andesitic terranes. Possible causes for textures and alteration being different in these deposits from the more classic Quartz-Adularia-Illite type epithermal systems may be that cooling/mixing rather than boiling dominates fluid evolution. Kaolinite may be also be a product of either of these different fluid types, or has resulted from overprinting of an illitic assemblage by downward percolation of acidic fluid.

Jan 1, 1991

By L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts, and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used.

Jan 1, 1926

Stress induced, gravity-assisted failure processes typically dominate long before stress levels approach the strength of the intact rock (at approximately smax > 0.4UCS where smax = 3s1 ? s3 and UCS is the Unconfined Compressive Strength of the intact rock (Martin et al. 1999)). Under these conditions, discontinuities typically become clamped and the failure process becomes brittle. This brittle failure process is dominated by new stress induced fractures growing subparallel to the excavation boundary. While it is possible to identify areas with the potential for brittle failure, for example, using the general assumption that brittle failure will occur in areas at right angles to the major principal stress (Hoek et al., 1995), when the threshold smax > 0.4UCS is reached in areas around the tunnel boundary, or elastic modelling and the Hoek-Brown brittle parameters proposed by Martin et al., (1999) (i.e. m? 0 and s ? 0.11), amongst others, recent observations discussed by Everitt & Lajtai (2004), and Kaiser (2005; 2006) suggest that brittle failure processes are enhanced when structural features such as joints, weakness zones, bedding planes or foliations are preferentially orientated around the excavation boundary creating stress raisers which in turn facilitate the stress-driven rock mass disintegration process (e.g., as illustrated by Everitt & Lajtai (2004) on Figure 1b). Such weaknesses induce stress heterogeneities that thus promote tensile-spalling failure processes (Diederichs 2000). The observations suggest that stress induced damage can occur ?prematurely? depending on the orientation of micro and macro structures in situations where the known stress conditions should not yet initiate brittle failure processes. In general, when structural features (micro and/or macro), especially foliations, are present in a rock mass, the strength is effectively reduced, largely due to tensile strength heterogeneity in areas depending on the orientation of the structural features with respect to the excavation boundary. As a result, stress induced damage could occur in areas not normally considered due to the influence of anisotropy (Figure 1).

May 1, 2009

By J. Brent Hiskey

Thiourea is a reagent capable of complexing gold and silver. With the proper oxidant, thiourea can effectively dissolve metallic gold and silver. A thiourea leaching system possesses potential advantages over conventional cyanidation including acidic solutions instead of alkaline, cationic complexes in contrast to metal-cyanide anoionic complexes, and faster leaching rates with acidic solutions of thiourea. Generally, the rate of metal dissolution in thiourea solution is fastest when ferric ion is employed as an oxidant. Acidic thiourea solutions for certain applications could offer a nontoxic and noncorrosive option for processing gold and silver. This paper provides information regarding the fundamental chemistry of the acidic thiourea system, and reviews the dissolution of both silver and gold in acidic solutions of thiourea. The recovery of gold and silver from acidic thiourea solution is discussed.

Jan 1, 1981

By Bruce I. Thomas

[THIS PAPER, tine of a series on placer ml n in iii Alaska, describes mining methods and gives unit costs at operations where hydraulic and mechanical excavation equipment is used with nonfloating washing plants. The mining methods described were developed during the last 30 years to copy with conditions peculiar to arctic and subarctic regions arid are now used by a large segment of the placer mining industry in Alaska. The operations described have been classified if m ii into three main categories: Those having sluices at a bedrock level, those having sluices above bedrock and those having mobile nonfloating washing plants (dryland dredges). Diesel-powered bulldozers and draglines convey or clevate gold-bearing gravel to the sluices, remove tailings, and strip waste gravel and other overburden. Diesel-powered centrifugal pumps supply water foe sluicing and hydraulic stripping. Detailed descriptions and unit cost arc presented for 14 operations to illustrate the numerous arrangements udder the first 2 categories.]

Jan 1, 1959

By N. Gatelier, T. You, J. C. Kandel

ABSTRACT: Underground hydrocarbons storage is a very specific domain for the designer. He is usually free to adjust the section, shape and layout to cope with the geological and geotechnical conditions. This paper presents a panorama of the geotechnical design of mined underground storage caverns, then lists a number of uncommon features encountered in a storage excavated in Sydney, Australia, the Elgas LPG project that had to face major non-isotropic conditions with numerous local variations, impacting on the achievement of the design profiles. Changes in geotechnical design methodology and practice are examined through this project, now in operation, which will have lasted altogether almost ten years. KEY WORDS: underground storage, geotechnical engineering, stability, methodology, design. ZUSAMMENFASSUNG: Die untertaegige Speicherung von Kohlenwasserstoffen unterliegt in der Planung sehr spezifischen Bedingungen. Der planende Ingenieur hat bei der Dimensionierung und Formgebung der Speicherhohlraeume gewisse Freiheiten, muss jedoch vorgefundene geologische und geotechnische Bedingungen beruecksichtigen. Der vorliegende Beitrag gibt zunaechst einen allgemeinen Ueberblick ueber die geotechnische Planung von bergmaennisch aufgefahrenen Speicherhhohlraeumen. Darueber hinaus werden Besonderheiten betrachtet, mit denen das Elgas LPG-Speicherprojekt in einer bergmaennisch aufgefahrenen Kaverne in Sydney, Australien konfrontiert war. Hierbei ging es um die Beruecksichtigung anisotroper Bedingungen mit zusaetzlichen Heterogenitaeten im Gestein und den daraus erwachsenden Schwierigkeiten, die geplante Hohlraumform zu verwirklichen. Ueber einen Zeitraum von fast 10 Jahren, in denen das jetzt in Betrieb befindliche Projekt unterschiedliche Betriebsphasen durchlaufen hat, wurden verschiedene geotechnische Entwurfsverfahren auf ihre Anwendbarkeit geprueft. SCHLUESSELWOERTER: Untergrundspeicherung, Geotechnik, Stabilitaet, Entwurfsverfahren, Planung. RESUME : Le stockage souterrain d’hydrocarbures est un domaine très spécifique pour le concepteur, car celui-ci dispose d'une large liberté pour adapter les sections, les formes et les implantations aux conditions géologiques et géotechniques de l’environnement choisi. Après un panorama de la conception géotechnique des stockages souterrains d’hydrocarbures par la méthode dite des cavités minées, l’accent sera mis sur un certain nombre de particularités rencontrées lors du projet de stockage de GPL de Elgas à Sydney en Australie, creusé dans de très fortes conditions d’anisotropie du massif rocheux, avec de nombreuses variations locales et toutes les implications que cela peut avoir sur le maintien des formes. L’évolution des approches méthodologiques géotechniques durant la dizaine d'années de développement de ce projet depuis les premières études jusqu'à l'exploitation actuelle est également présentée. MOTS-CLEFS : stockage souterrain, géotechnique, stabilité, méthode, conception.

Jan 1, 2003

By David J. Lowell

The gold content of porphyry copper deposits ranges from less than 0.05 g/t to more than I g/t ((0.0017 to 0.035 oz per st) and the average is about 0.05 g/t (0.0017 oz per st) gold. Perhaps the highest grade mineralization found near a porphyry cop¬per deposit is the Ok Tedi Gold Cap ore body whose grade falls in the 2 to 3 g/t (0.07 to 0.1 oz per st) range. It is difficult to define a gold-rich por¬phyry copper deposit. All porphyry copper ore bodies contain some gold, but there seems to be a fairly sharp break in the gold content at about 0.1 g/t (0.003 oz per st) gold. There is also a problem in identifying dis¬seminated gold deposits that may have an indirect relationship to porphyry copper systems. This relationship is clear cut in deposits such as the Ok Tedi Gold Cap, the El Hueso deposit, the Fortitude and West de¬posits at Battle Mountain, NV, and the Sur¬prise deposit at Ely, NV. There are many other bulk disseminated, epithermal-type gold deposits - McCoy, NV, for example - that might be related to a porphyry system but where this relationship is remains very uncertain. In such places as the Goldfields and Tonapah district in Ne¬vada and in the El Indio, Chile district, there may be a vertically stacked ore deposit rela¬tionship between near surface epithermal deposits and disseminated molybdenite and chalcopyrite enargite mineralization at depth that may represent a deep porphyry system. This, however, has not been positively demonstrated. Most of the bulk epithermal gold deposits are probably not related to porphyry copper systems. Exceptions would probably be Ok Tedi, El Indio, El Hueso, Battle Mountain, and Lepanto where vertical or lateral zoning relationships are more apparent. This author believes that porphyry copper systems are related to a relatively unique type of intrusion that is probably distinct from, for example, the McCoy intrusivebody. For that reason, deposits such as McCoy, Chimney Creek, and the like will not be included in the definition of gold-rich por¬phyry copper deposits for this article. The interpretation of the origin of several of the deposits previously mentioned are subject to an unusual amount of contro¬versy. For example, geologists seem to be equally divided about the presence of a porphyry copper deposit below the El Indio deposit. Geologic setting Continental vs. island arc Several geologists have speculated that the gold-rich, moly-poor, porphyries are

Jan 1, 1989

By Francis Kendorski

The Skyline #3 Mine of Canyon Fuel Company in Utah was planning longwall mine development adjacent to and downdip of older mine workings known to be flooded. Barrier pillar geometries and widths were proposed by mining company personnel. Hydraulic conductivity testing suggested that the general characteristics of the local coal seam, dikes, and faults are only weakly conductive and that leakage through the barriers, if any, would be minor. The mechanical performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods and (2) numerical stress modeling. Comparison of the proposed design, with the range of barrier widths derived from the empirical methods, served as a first-order check on the adequacy of the proposed design. Numerical modeling was used to evaluate conditions site-specific to the Skyline #3 Mine and barrier geometry. Models were developed to quantify the relationship between barrier width and the abutment stresses onto the future workings. The models were also used to estimate the stress distribution within the barrier pillars. The hydraulic performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods for hydraulic impoundments, (2) empirical method estimates of seepage through coal barrier pillars, (3) numerical hydrogeologic flow modeling, and (4) numerical strain modeling. Using the techniques described above, and based on relevant industry experience, underground observations, knowledge of local geologic conditions, hydrogeologic measurements, and analytical results, the level of geomechanical risk associated with the barrier design as proposed was considered low and the level of hydraulic risk was considered moderate. The largest uncertainty that remained was the possibility that unfavorable geologic structures, such as faults and dikes, would act as conduits for leakage of impounded water into the new workings. Although the study indicated only minor steady-state leakage would occur through a small number of known structures, the presence and full leakage potential of threatening structures in the barrier could not be reliably known until the barrier was mined. One longwall panel has been completed adjacent to the barrier with no evidence of water flow even in fractured zones. Thus, as predicted by the modeling and analysis, it appears that abutment stresses imparted on the barrier during mining did not substantially alter the natural hydrogeologic characteristics, or leakage potential, of the barrier. The longwall coal mine water-barrier pillar design and performance are considered a success.

Jan 1, 2007

By Nils Heinke, Stephen M. Collinsorth

To anyone who is responsible for the production of blast holes, who is looked to on a daily basis for drill maintenance and performance, whose bottom line may depend on the survival of the mine itself.. How much awareness should one have on such things that truly impact production, maintenance and overall job cost? Do you know your drill’s maximum capacity?

Jan 1, 1998

By Gabka T., R. E. Gregorczyk

Work to improve employees' behavior in Głogów Copper Smelter began in 2009. It has been noted that over 90% of accidents at work are attributable to human reasons. At that time, a series of external workshops was contracted based on exercises conducted by a psychologist trainer with supervisors. Having trained about 300 employees, an observation of employee behavior at workstations was started as part of the control of risk reduction measures. As a result of the above actions, the number of accidents was reduced by half between 2009 and 2017. Currently, internal workshops for communication improvement for behavioral auditors are conducted by the employees of the Smelter. Named: "I observe, react and communicate" and aimed at further mastering the elements of the safety culture in Głogów Copper Smelter. INTRODUCTION KGHM Polska Miedz is an integrated mining and smelting copper producer based in Poland and operates on the international metal market. KGHM, with annual production of over 500 thousand tonnes of copper, holds a middle position in the world ranking of copper producers. At the same time, in Europe it is the largest producer of copper from its own ore deposits, possessing its own integrated production structure, from underground mining operations to final, top-quality product. It is also worth mentioning that KGHM Polska Miedź is one of the largest Polish exporters and, apart from copper, is a significant primary silver producer in the world. The mission of our company, consistent with its strategy, is to produce copper and silver in a safe mode for workers and the environment, with reduced environmental impact. Therefore, "Głogów" Copper Smelter operations are continuously focused on the creation of safe working conditions, and minimizing the negative effects on the environment. The company meets the requirements of an Integrated Management System comprised of the following: Quality Management System ISO 9001:2008 Environment Management System ISO 14001:2004 OHS Management System according to the requirements of BS OHSAS 18001:2007 Being a proud socially responsible company, we are aware that part of an efficient OHS system is to recognize, monitor, prevent, educate and motivate, thus continuously improve working conditions for 2500 employees of Głogów Copper Smelter &Refinery. We clearly communicate that a low accident rate is beneficial for both, staff and the company, and is of utmost importance as a part of our health policy.

Jan 1, 2019

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the postgrinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances and allowing a more precise mill sizing. Therefore we surrounded the grinding crucible of the Hardgrove mill with a crucible furnace to heat it. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids (water and alkali) with different temperatures. The required heating power is 2000 W. In the implemented equipment we installed four 230V/500W electric heating wires made from heat-resistant alloyed material and surrounded by ceramic insulators. The temperature and temperature-gradient are measured by four PT100 platinum thermal resistors. The data acquisition and control program written in the C language in the Lab Windows CVI program environment measures the voltage proportional to the temperature. Determining the grindability indices of hungarian and greek bauxites experimentally, first dry grinding tests were carried out under standard conditions. During wet and alkaline grinding, to 50 g of dry bauxite 85.5 g of industrial alkali with a concentration of about 200 g/l was added. As grinding aid 2 g of CaO (4 % of dry bauxite) was dosed. From the data it can be concluded: - The tested bauxites show a similar behaviour against temperature change. However, the extent of grindability change is different for different bauxites. - Soft Hungarian boehmitic bauxite can be ground in a high-temperature alkaline medium better than hard Greek one. The increase of grindability according to the high-temperature Hardgrove indices: (kHT = Dry o HT,alkaline H /H ): for hard Greek and soft Hungarian boehmitic bauxites: kHT = 1.7 and 2.4 respectively; according to estimated Bond indices (kB,HT =Wi,dry/Wi,HT, alkaline ): kB,HT = 1.6 and 2.1. - The increase of grindability is the most important factor the reaction of kaolinite with caustic liquor and lime and the loosing of the textural structure at 80 ºC and especially at 100 ºC.

Jan 1, 2003