Search Documents

By Scales PJ, Ralston J

Fine coal particles have been examined with respect to dustiness and its connection with various physical and chemical properties. It appears that a given coal will tend to be dusty ifthe moisture content is low and if the inert maceral content and overall rank are high. The hydrophobicity ofa coking coal (Young-Wallsend) and a steaming coal (Blair Athol) was examined in detail by a dynamic contact angle technique. The YoungWallsend coal had a higher contact angle, on average, than the Blair Athol sample. This result has important implications for dust suppression and associated processes.

Jan 1, 1986

In September 2003, a test was conducted to see if a115-mm- (4.5-in.-) diam Mocap Vari-Stem blasthole plug could improve the pattern of explosives using different top stemming material. The test took place at the J.S. Faulkroad and Sonsstone quarry in McCalisterville, PA. The test consisted of a production stone blast. Half of the holes were stemmed with standard crushed stone. Two-thirds of the remaining half were stemmed with Vari-Stem plugs and crushed stone. And the remaining one-third of the second 50 percent was stemmed with Vari-Stem plugs and only drill cuttings.

Jan 1, 2004

By Archie Richardson

The trona mines in the Green River Basin, commonly known as the "trona patch," present an interesting set of rock mechanics issues stemming from mining in a unique underground environment. Like other minerals occurring in tabular deposits, trona is mined using high-productivity room-and-pillar and longwall methods. However, trona does not behave quite like other evaporites and behaves far differently than coal. In this paper, the following key issues in trona patch rock mechanics are discussed: material properties, in situ stress field, water and gas pressure effects, creep characteristics, pillar behavior, roof span stability, floor stability, underground tailings storage, longwall mining, two-seam mining. and solution mining. Many of the existing trona producers are entering potentially more difficult mining conditions, and much consideration is being given to "new" technologies such as longwall mining and solution mining. In analyzing 20 years of experience with trona patch rock mechanics issues the authors have identified key comparisons and contrasts with conventional tabular deposit rock mechanics that will help illuminate what has been learned as the trona patch enters the 21" century.

Jan 1, 1999

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By Axel Sahlin

Jan 1, 1898

By F. Terblanche, M. Holton, A. Kruger

The paper presents an optimal mine planning system designed to simultaneously optimize all the underground mines of large South African gold and platinum mining corporations. The system, code named PlanIT-OPTIM, is a multi-stage solution involving the use of adetailed 3D CAD-based mine planning system (CADSmine™V4). The mine design and scheduling rules defined in CADSmine™ are responsible for simulating mining sequencing, rock mechanics, and ventilation, etcetera. Feasible production ranges generated by CADSmine™ and various high-level mathematical models are used as inputs to a mathematical optimization engine. The optimization engine produces optimal production profiles (i.e. key business indicators such as tonnages, mineral and areas extracted per time period) by maximizing net present value. Other objectives such as profit continuity, production continuity and maintaining available reserves can also be specified as optimization criteria. The final step in the PlanIT-OPTIM process is to convert the optimal production profiles into practical and attainable business plans. This is achieved through the CADSmine™ Detail Optimization Engine that modifies the original CADSmine™ schedule to match the optimal production profiles. With current methods it is an impossible task to find the best business plan for a mining corporation in any reasonable period of time should conditions change (e.g. gold prices, exchangerates, grade estimates, etcetera). The fast turn around time achieved through PlanIT-OPTIM makes it possible to do several ‘what-if’ scenarios in a reasonably short time. PlanIT-OPTIM has already been used in the gold mining industry to find optimal business plans for a mine.

Jan 1, 2003

A detailed study of the capital investment and production cost for copper electrowinning plants shows that significant savings in both can be achieved by increasing the current density. From the economic analysis it is determined that the optimum current density which will result in lowest capital investment and lowest operating cost is between 60 A/sq. ft. and 70 A/sq. ft., or at least three times as high as the Conventionally employed current density. The specific investment, expressed as $/ton-year, is found to be a function of both the current density and plant capacity and has a minimum value at the optimum current density. Empirical equations are developed for the purpose of estimating the capital investment and operating cost for plants of any production capacity operating at any current density.

Jan 1, 1972

By Junya Tokita

In Japan, packaged explosives have traditionally been used as the most common explosive for tunneling. Recently, some blasting systems such as ANFO with a kettle loader and emulsion explosives with a pump loader have been trialed in order to improve safety and efficiency of the charging process. There are issues with these systems relative to the Japanese market. ANFO dissolves in water easily, and generates ammonia gas when it contacts with concrete. Emulsion explosives need costly pump ing unit s, and there is a need to control residuals in the pump unit. Additionally, there are obstacles by Japanese law to site mixing of emulsion explosives.

Jan 1, 2005

By M J. Kindley

The Golden Cross Gold Mine Project is now fully operational and into its second year of operation. Because of its location in the sensitive Coromandel Peninsula , strict water management and environmental requirements had to be met. This led to the development of new technologies for cyanide recovery and the adoption of advanced water management and water treatment systems. This paper discusses the water management and treatment system adopted for contaminated water at Golden Cross and provides data on the operational history to date.

Jan 1, 1993

By Richard E. Gray

The Office of Surface Mining Reclamation and Enforcement (OSM) is preparing an Abandoned Mined Lands Reclamation Control Technology Hand- book. (l) GAI Consultants, Inc. , recently prepared Chapter 2 on Mine Subsidence Control which contains a summary of subsidence abatement measures plus two new decision matrices for evaluating the subsidence abatement options that might be considered for a particular problem. These decision matrices are presented for information. Review of the subsidence abatement methods resulted in identification of items where research may impact the current state of technology in mine subsidence control. These research needs are presented to stimulate discussion of their importance in subsidence abatement and to encourage funding agencies, researchers, and practitioners to work on them.

Jan 1, 1982

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By D. S. van Vuuren

Over the last 60 years many different processes were conceived to reduce the cost of titanium produced by the Kroll process. However, success eluded all previous efforts, which were consequently terminated in periods of economic downturn. Recently, the grow thin demand for titanium and the high cost of producing the metal again sparked renewed attempts in various parts of the world to replace the antiquated Kroll process with a more efficient route. The different options to produce titanium are reviewed, classified and evaluated in terms of the fundamentals underlying the technologies, and it is shown that the options considered to be the most likely to replace the Kroll process, are continuous processes to reduce TiCl4 metallo-thermically to titanium powder. Of these, continuous magnesio-thermic reduction of TiCl4 would conceptually result in the lowest-cost and highest-value product. However, when considering by-product salt removal from the titanium product and recycling of the salt as well, sodio-thermic reduction of TiCl4 is better.

Jan 1, 2009

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014

By Virgil Miller

Bureau of Mines Reports of Investigations 3244, 3245, 3246 and 3264 give data of detailed studies on smelting in the lead blast furnace handling zinciferous charges at Trail, B. C. The present paper gives more on analyses of the gases leaving the top of the charge and on accretions formed on the walls of the blast furnace. New data are presented to show the effect of the temperatures at the tuyere zone on the lead content of the slags made. The greater part of this paper, however, deals with a much debated subject, namely air used in lead blast furnaces. Original data are presented to show the effects on smelting lead 'products when air is supplied to a lead blast furnace under volume versus under pressure control.

Jan 1, 1940

By Virgil Miller

Bureau of Mines Reports of Investigations 3244, 3245, 3246 and 3264 give data of detailed studies on smelting in the lead "blast furnace handling zinciferous charges at Trail, B. C. The present paper gives more on analyses of the gases leaving the top of the charge and on accretions formed on the walls of the blast furnace. New data are presented to show the effect of the temperatures at the tuyere zone on the lead content of the slags made. The greater part of this paper, however, deals with a much debated subject, namely air used in lead blast furnaces. Original data are presented to show the effects on smelting lead 'products when air is supplied to a lead blast furnace under volume versus under pressure control.

Jan 1, 1940

By S. Al-Hassan

The deposit has been exploited for Mn oxide and carbonate since 1916. Known reserves of MnO, however, are almost depleted and the survival of the mine will depend on the exploitation of the carbonate. Kriging, inverse distance weighting (IDW) and cross-sectional methods have been applied to the evaluation of the carbonate resources and reconciliation of the estimates obtained shows that kriging and IDW give almost identical block values. A comparison using conditional probability indicates that there is virtually no difference between the global reserve estimates derived from the cross-sectional and kriging methods. The physical causes of these similarities are highlighted and the problems of dealing with multimodal distributions are discussed together with the difficulties of semi-variogram modelling

Jun 19, 1905

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By Robert E. Wallhagen

This report describes the results of a four year investigation into improved face ventilation systems for underground coal mines. The objective was to experimentally determine configurations for a diffuser fan system and a water spray (spray fan) system which will provide a maximum reduction in face methane concentrations without causing an increase in methane concentrations at the operator's position. The experimental evaluation was performed in full scale mock-up mine entries, simulating continuous mining operations in both a six foot and four foot coal seam complete with normal ventilation, water sprays, and methane emission. A limited study was also performed to assess the effect of scrubber discharge location on methane concentrations in the face area. The results indicated that diffuser fan and spray fan systems that were designed to augment the natural airflow pattern in the entry could provide a factor of 3 to 5 reduction in average methane concentration at the face, compared to a mining machine with just conventional water sprays. The properly designed diffuser and spray fan systems also significantly reduced the total methane present in the entry. A properly designed dust scrubber discharge can reduce face methane levels by a factor of two.

Jan 1, 1977