Search Documents

By D. D. Munro

Finsch Mine is a kimberlite diamond mine located at Lime Acres in the Northern Cape Province of South Africa. The mine was founded in 1961 and started surface mining in 1964. Underground production commenced in 1990 using a modified blast-hole open stoping method for the mining of Blocks 1, 2 and 3. Block 4 is currently being mined as a block cave. The process of identifying and optimizing a method to mine the Block 5 orebody started in 1991, and in 2006 incline caving was identified as being technically feasible. This paper aims to document the process employed in developing this method by the Block 5 prefeasibility team as well as discuss the technical challenges encountered during this process. The paper commences with a history of Finsch Mine and highlights the complex geology and threat of sidewall failure that prompted the decision to use block caving as the mining method for Block 4. A literature study of mines that implemented mining methods upon which the incline cave was conceptualized is then presented. These practices were then used to form the basis for the designs on which the initial geotechnical modelling was done and built upon through an iterative process of modelling and design changes. The ventilation of the mining area, initial productivity simulation results, and the applicability of automation and comminution processes in the incline cave are also presented. The paper concludes with an investigation into some of the challenges of the mining method, and shows that that incline caving is a technical option available for further investigation in determining the optimal mining method to be employed at Block 5, Finsch Diamond Mine. Keywords massive mining, incline caving, geotechnical modelling.

Jul 1, 2013

The Australian Centre for Minesite Rehabilitation Research (ACMRR) was established through a mining industry initiative to meet the need of industry, governments and the community for sustainable systems for land affected by exploration, mining and mineral processing activities. The Centre, which is a consortium of the major groups associated with mining rehabilitation research in Australia, has a focus on both strategic research and technology transfer and combines a wide range of multidisciplinary skills covering engineering and the physical and biological sciences. The paper briefly describes the goals, structure, expertise and research and technology transfer activities of the Centre. The major research program areas of waste rock dump and final void stability, acid mine drainage, tailings disposal, and remediation of ecosystem reconstruction are described in the context of national priorities.

Jan 1, 1995

Recent developments in diamond drilling practice have been chiefly 'concerned with modifications in drill design and 'operating technique whereby an increase in daily footage rates and reduced footage costs have been achieved without any marked improvements in the recovery of core. This trend is perhaps due to the general acceptance by the mining and drilling engineer alike of the belief that diamond drilling has definite limitations in exploratory work on mineral deposits characterized by irregularities in continuity and grade, such a belief arising from the fact that drilling technique has not yet evolved coring devices to ensure the full recovery of the rock and mineral formations penetrated.Current diamond drilling operations at Moonta and Wallaroo Mines, carried out by the South Australian Department of Mines, have attained remarkable results in completely eliminating core-loss by the use of a special double-tube core barreI.It is considered that assays of borehole samples taken with this special barrel have a reliability comparable, if not superior to that of similarly situated mine samples and, provided they are spaced satisfactorily, can be used as, a basis for calculating tonnage and grade. Formerly, with only partial core-recoveries, positive borehole results on narrow irregular lodes, such as those in the Moonta and Wallaroo Mines, could be accepted mainly as indications of the presence of mineralization, and could have only a limited bearing on estimates of ore reserves.The value of this special double-tube core-barrel lies In the fact that it guarantees good core recovery and, therefore, good samples, and eliminates the need for sludge-sampling, which is prone to give unreliable assay results from several causes, such as gravity concentration in the bottom of the hole and return water losses which cannot be overcome.In view of the increasing demand for minerals and the probability that the search for them will be carried on largely by boring, it is felt that it would be of interest and value to direct the attention of mining engineers to core-recovery results obtained by diamond drilling plants in South Australia and the features of the special core-barrel, designed by the writer, which has made this possible. Also, the writer is desirous of placing on record two other core-recovery devices designed to extract accurate samples in relatively soft or unconsolidated formations. The latter are used with percussion and calyx plants, respectively and their value has been proven on phosphate rock and coal deposits in South Australia.

Jan 1, 1943

By D Craw, I M. Turnbull, R J. Norris, N Mortimer

The Otago Schist is being subdivided on a regional scale into structurally, metamorphically and lithologically distinct blocks. Differences between blocks are subtle, and difficult to map in the field. Boundaries are late-metamorphic or immediately post-metamorphic in origin, and are different from later brittle faults which disrupt the schist. Mapping of late-post-metamorphic structural discontinuities has direct application for basic grassroots exploration in the Otago Schist. The mineralised (and currently mined) Hyde-Macraes Shear Zone forms a regional scale boundary between a block dominated by politic schist and a block with massive psammitic schist, pelitic schist, and minor greenschist and chert. The HMSZ forms a metamorphic discontinuity, with garnet and biotite in the underlying schist, and neither index minerals apparent in the overlying schist. The HMSZ is also a structural boundary between domains with differing lineation orientations. The HMSZ can not yet be traced along strike to the northwest to the Rock and Pillar Range, where the only major discontinuities recognised are the Caples-Torlesse boundary and a normal fault separating low grade from high grade schist. Structural and lithological discontinuities in the Dunstan Range break the range up into distinct structural blocks, two of which are separated by the gold-mineralised Rise and Shine Shear Zone.

Jan 1, 1999

By C. Sun

In this study, numerical simulations of yield pillars employing the finite element method with time-dependent Drucker-Prager material model are conducted. The stress control mechanism of yield pillars on weak floor strata is studied. The development of pillar yield zone, the distribution of pillar stress and the development of failure zone in the weak floor strata are investigated. The study indicates that a properly selected yield pillar size may significantly reduce the peak stress induced in the weak floor strata and effectively control the development of failure zone in the floor.

Jan 1, 1999

By D. R. Dollnar

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2002

By R B. Evans, M G. Townsend

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre-Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth. The raw material is crushed and fractionated to produce a product of less than two micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

By Sam Ammermann, William Heasley

"The mining industry is on an ever accelerating path to complete mechanization. As companiesutilize more sophisticated and efficient methods of blasting, a more thorough look should begiven to the pros and cons of mechanized shaft sinking. Historically, Vertical Shaft SinkingMachines (VSSM) have been capital intensive, making it hard to enter lowest bidder marketssuch as the United States. As advances in safety and technology have occurred, VSSM methodsare becoming increasingly common in many countries outside the United States. Decreasedcapital requirements, a greater amount of competition within the VSSM market along withgreatly improved safety practices, have made it more competitive with traditional drill and blast(D&B) methods. However, VSSM technology has yet to be embraced by the United States. Alarge culture shift will have to occur before VSSM technology will become common in theUnited States. The history, and advent, of raised boring machines will be discussed and how itrelates to the current development of VSSM technology. The researchers will analyze the uniquerisks of D&B methods and how they compare with the unique risks of VSSM technology. Theresearchers will put an emphasis on risks directly affecting the safety of personnel working onthe shaft sinking operation. Many of these risks are identified by contracting companies withregards to geology, relative location of resources and the chosen shaft sinking method. Theresearchers will discuss specific risks a given shaft sinking company will want to consider whenchoosing between D&B and VSSM methods."

Jan 1, 2016

I have chosen this subject in view of the fact that, while there are many and ample opportuuities of getting reliable assays made, there are but few who are in a position to obtain reliable data on the sampling of minerals and metals my long experience at Port Pirie, where, for five years, I had charge of the Refining and Sampling Mill, showed me how important it was that a correct sample should be taken.Weighing; This, to the ordinary layman, seems so simple that no expert knowledge is needed, but in actual practice there are hundreds of pounds to be lost by the lack of knowledge in this department.(1.) There is the matter of weighing in large or small quantities.(2.) The class of weighing machine used.(3.) The accuracy of weights used.We all know that, say, 1000 tons of ore cannot be weighed in one parcel; but the fewer the weighings the less loss to the seller (and usually wishes it weighed in small lots carefully) for it is a well known fact that the most sensitive scales take a certain weight to show distinctly the indication of the balance, or, in other words, what is known as "the pull of the scales." As for instance, 1000 tons weighed in lots of 1 c. each, taking the pull of the scale as being equal to 1 lb., would give a result of 9 tons loss to tbe seller, and as most of the ore sent to Customs works is worth 5. -£20 per ton-this would mean £180 loss to the careful man.

Jan 1, 1901

By R. W. Pugh, D. G. Bellow

"This paper will describe how cultivator shanks are made in one company and how the manufacturing was studied with a view to increasing product consistency and reducing manufacturing cost. The product: which is used extensively in the agriculture industry, was analyzed to determine which geometric parameters optimized its design and whether there was justification for the great variety of styles and shapes that are available in the market. Finally, an extensive series of field trials were undertaken which showed that it is advantageous to the manufacturer to be better aware of the loads and forces that his product is subjected to by another industry.IntroductionStelco maintains a Research Group for its Western Region operations headquartered in Edmonton, Alberta. Because of the small staff, a location that is isolated with respect to its Burlington, Ontario centre and a diverse set of processes and products, a university relationship has developed which may be different from that which would be developed at a larger integrated Steel Works. This paper outlines the type of cooperative studies carried out by Stelco Inc. in Edmonton and the University of Alberta. .To meet the research needs covering a wide variety of steelmaking processes and steel products produced in Edmonton would require more staff and equipment than the sales volume in the West justifies. The gap is filled by cooperation with university personnel. This cooperation has provided these benefits to Stelco Inc.:• access to specialized test equipment and a trained staff to operate it; and• assistance from experts in the areas of product testing and problem solving.Moreover, the close proximity of the university to the plant allows frequent meetings and ensures that practical solutions are developed and implemented. A good example of the ongoing university I industry relationship developed is the joint work on improving cultivator shanks."

Jan 1, 1982

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918

By R. O. Burt, D. J. Ottley

"SYNOPSISRecent developments in the use of the Bartles-Mozley table and the Bartles CTS screen are described for the gravity preconcentration of fine heavy mineral and metal particles present in low grade pulps. The B-M table is a relatively new device used for the recovery of particles of up to 100 micron size down to 5 microns or in the case of gold and platinum, down to 1 micron. The CTS screen is a wet screening device used for feed preparation ahead of the Bartles-Mozley table and will size effectively down to about 300 mesh. Results and operating data for a number of different materials are given including outline flowsheets; the effects of the major variables on the performance of the table are briefly discussed. The potential of the B-M table to treat a variety of different ores, coal, tailings, and waste products are considered. The utilization of the B-M table in association with other unit processes to improve overall results as well as to improve the economics of design and performance of plants are also mentioned.INTRODUCTIONA number of new gravity concentration devices have been developed in recent years for the recovery of fine heavy mineral and metal particles but for reasons which include low capacity, high capital or operating costs, competition from other and better processes, the absence of simplicity or reliability in operation etc., only a few which include the Bartles-Mozley table, have been proved to be of commercial application.The name of the machine is derived from the inventors name, Richard Mozley, who developed the B-M table at the University of Bristol in England. The table was subsequently taken up and patented, world-wide, by the National Research Development Corporation a British government agency. An exclusive license to manufacture the table was granted by NRDC to Bartles (Carn Brea) Ltd. in Cornwall, England."

Jan 1, 1973

By A N. Kasnanto, D A. Sims, J Pocoe, B Pulungan

In this case study we compare the sampling quality of diamond drilling (DD) and reverse circulation (RC) drilling at the high sulfidation Purnama gold–silver (Au-Ag) deposit located in northern Sumatra, Indonesia.There was a systematic bias of 23 per cent gold metal under-call in the diamond drilling based Ore Reserve estimate compared to the mill reconciliation over three years of production. The RC based Grade Control data and mill production data were in much closer accord. Investigation led to quantification of the significantly reduced sampling imprecision (or improved precision) of RC drilling samples relative to diamond drilling samples and the determination of a grade bias between the drill types caused by sample volume and metal distribution in the mineralisation. An infill RC drilling program was undertaken to improve data density across the pit for inclusion in the Mineral Resource estimate. This subsequently increased Au metal in the estimate by 16 per cent.The sampling imprecision of primary diamond drill sampling is rarely tested. Duplicate sampling can be used to quantify sampling imprecision at each stage of subsampling. In diamond drilling it is tested at the primary sampling stage via second half core sampling, while RC sampling is tested with field duplicate sampling at the rig. Duplicate data can be compared in a number of ways to determine imprecision including Thompson-Howarth plots which quantify imprecision to allow comparison between different methods and protocols. Comparing sampling imprecision between data sets and data types allows determination of optimum drilling and sampling protocols and can reflect upon the underlying validity of Mineral Resource input data and estimation outputs.CITATION:Sims, D A, Pocoe, J, Kasnanto, A N and Pulungan, B, 2017. Why combine reverse circulation and diamond drilling in Mineral Resource estimation at Purnama?, in Proceedings Tenth International Mining Geology Conference 2017, pp 413–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By Alexander Nikolic

The paper presents the foundation design and construction of a landmark urban redevelopment scheme in central London, UK. The scheme comprises the new Tottenham Court Road Underground station, Crossrail interchange box and associated over-site commercial development. The paper focuses on the design, procurement and construction of large diameter bored piles, up to 68m in depth, which form the foundation support system for the over-site commercial development at Denmark Place. The congestion below ground required an intricate foundation design solution which has been a catalyst for developing innovative load transfer arrangements and has resulted in the advancement of pile construction technology in the UK. The foundation system was also designed to cater for the construction of two significant elements of proposed below ground infrastructure. Selected large diameter piles have been constructed within 1.1m of live underground railway tunnels. An innovative D-shaped pile was constructed in a zone subject to particular spatial constraints. The proposed Crossrail tunnels will be bored within 1m of selected over-site development piles. In addition, a 30m deep excavation forming a new escalator box will be constructed in direct contact with the over-site development piles. The stakeholder engagement process is described together with the foundation design development and buildability assessment. The benefits from early collaboration between the designers and specialist contractors are highlighted. From an analytical design perspective, the entire foundation construction sequence was modelled in detail in order to assess the soil structure interaction and any potential adverse effects on existing elements of underground infrastructure. The results from the three dimensional numerical modelling simulation are compared with field monitoring data.

Jan 1, 2011

By J Belke

Murrin Murrin Operations have not had a successful beginning. Numerous reliability and operability issues, many of which are the result of design decisions, have been addressed through mechanical and operational changes and the CCD circuit is no exception. Four design aspects of the CCD circuit that have caused and continue to cause operational problems are: the inclusion of solution neutralisation gypsum in the CCD circuit feed which was designed solely for HPAL residue without proper investigation of its impact on the achievable underflow density and resulting wash efficiency; the decision to construct the thickener base from thickened solids; the lack of redundancy in the overflow, underflow and tailings pipe work; and the lack of thickener operational flexibility in the central rake-lift and feedwell dilution system. In November 2002, the lack of operational flexibility in the rake-lift and the feedwell dilution system was improved through mechanical modification as follows:CCD1 rake mechanism was modified to allow central vertical lift of 600 mm; and CCD1 changed to forced dilution using the Outokumpu TurbodilRântechnology by replacing the E-DucânRtechnology of Eimco. The installation and the results of the CCD1 rake-lift mechanism and feedwell dilution system changes are discussed in this paper.

Jan 1, 2004

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 39,420 acres of the 60,960-acre Skedaddle Wilderness Study Area in order to evaluate its identified mineral resources. There are no known mines or mining operations in the study area. None of the prospects or claims in or within a 1 mile peripheral zone around the study area have recorded production. At least 276 recorded lode, 6 unrecorded lode, and 29 placer claims have been located in and within about 1 mile of the study area. Approximately 191 of the claims are in the study area. Four of these were current in 1985; all four are wholly or partly inside the study area. None of the study area was being explored by private industry in 1985. Metallic and nonmetallic commodities present in the study area consist of gold, mercury, perlite, basalt, pozzolan, stone, and sand and gravel. Perlite is represented by a single deposit which contains 184,000 tons of subeconomic resources in and adjacent to the study area. No other sites contained identified resources. There are no other identified nonmetallic resources in the study area. Occurrences in and near the study area contain small amounts of gold and mercury in vein-type deposits and show characteristics similar to bulk-tonnage, low-grade gold deposits. No base-metal resources were identified. The gold and mercury mineralization and perlite deposit are spatially related to a volcanic center located in the Skedaddle Mountains. Prospects in the Skedaddle Mountains may contain both precious metals and perlite resources, but additional work is required to adequately delineate these areas.

Jan 1, 1987

By C. H. Wayman, D. W. Fuerstenau

The effect of bubble size and concentration of certain reagents on the terminal velocity, shape, path, and drag coefficients of single air bubbles in distilled water has been investigated. Bubbles of a certain size range rise considerably faster than Reynolds number-drag coefficient relationships predict, whereas a small amount of frothing agent reduces their terminal velocity. The rapid velocity at which bubbles rise in distilled water appears to result from slip at the boundary and from circulation within the bubbles. Surface-active agents retard bubble motion through prevention of both circulation and slip at the boundary. A surface tension concentration gradient helps maintain bubble sphericity. HE gas phase is one of the indispensible in-gredients in flotation operations. Flotation depends on the collision of an air bubble and a mineral particle in a pulp and their ability to remain in contact long enough for adherence to take place. Before it is possible to understand the mechanics of air bubble-mineral particle encounter, it is necessary to learn more about the nature of bubbles themselves before collision with a mineral particle has taken place. To date, little work has been done on air bubbles in flotation systems. In 1945 Fahren-wald' presented a study of the role of frothers on air bubbles and on aeration in flotation, and recently Wark and Sutherland' discussed the work of Rosenberg- in relation to flotation. The research reported in this present article was undertaken to investigate systematically the effect of bubble size and the concentration of certain reagents on the terminal velocity, shape, path, and drag coefficient of single bubbles in distilled water. Most of the work is concerned with the effect of a-terpineol on bubble motion in water, but studies were made with potassium chloride, potassium hydroxide, potassium ethyl xanthate, and potassium amyl xanthate. Experimental Method and Materials: To obtain free bubble rise and reduce wall and surface effects, the investigators used a tank of 5½x5½x30-in. internal dimensions, filled with water to within 4 % in. of the top.' The tank was made of acrylic plastic so that the walls would have good optical properties. Distilled water, which was re-distilled in a block tin still and saturated with air before each test, was used in all the experiments. All solutions were made with reagent-grade chemicals. During each experiment the water was at room temperature, and during the course of an experiment the temperature did not fluctuate more than 0.5°C. Since the experiments were performed over a period of six months, the temperature varied between 25° and 27°C. The temperature at which each series of experiments was conducted is recorded with the data. The experimental apparatus is presented dia-grammatically in Fig. l. Individual air bubbles were generated from purified compressed air through a capillary of 0.003-cm internal diameter at a rate

Jan 1, 1959

This paper forms the second of a series, in which it is proposed to communicate the results of an extensive research into the influence of alloying elements on the physical properties of lead, now being carried out in the Metallurgy School of the University of Melbourne.Some general comments on this research were made by the present writer as an introduction to the first contribution by R. S. Russell*: It was there pointed out that it was the intention to prepare lead as pure as possible, to determine its properties and then to make alloys with the various elements added singly, and in various combinations, in order to determine the effect of each. This line of action is still being pursued.It occurred to the writer, however, that this fundamental attack might, with advantage, be accompanied by a parallel investigation in which lead of commercial purity would form the basis material. In this way, using a standard *Professor of Metallurgy, University of Melbourne.

Jan 1, 1934