Search Documents

By Whiten W. J

An investigation on the breakage characteristics of closely sized orc samples at different levels of input energy was carried out to determine an appearance function for possible use in ball mill modelling. A consistent pattern of breakage behaviour was observed and the resultant size distributions could be described by a one-parameter, ('t'), family of curves. For each particle size range tested, this parameter 't' has an exponential relationship with input energy below an upper energy limit. A tentative linear relationship between the input energy at a constant value of 't' and the work-index leads to reconstruction of 'I' - input-energy curves from the work-index values. To normalise the efrect of particle size and input energy, multidimensional cubic spline regression was performed on thc entire range of data. The results indicated that the parameter 't' can be determined, reasonably accurately, as a function of Ln (input energy, kWh/tonne) and Ln (particle size, mm) for input energies between 0.5 and 8.0 kWh/tonne.

Jan 1, 1983

By O Haavisto, N Khajehzadeh, L Koresaar

Online analysis of metal content can be used to optimise the grade and recovery of a flotation circuit. Compared to conventional laboratory analyses, the benefit of an online analyser is the speed of the measurement, therefore disturbances (eg changes in feed grade and decrease in recovery) can be reacted to in real time by an operator or automatic process control system. In some cases traditional X-ray fluorescence analysers can be applied to silica analysis in iron ore when the SiO2 grades are high enough and have a negative correlation with iron; however, generally a laser-induced breakdown spectroscopy (LIBS) analyser is more suitable for low Z elements.The Outotec Courier 8® analyser is a LIBS based analyser able to measure elements starting from lithium (Z = 3), thus being able to measure impurities; eg silica and aluminium directly in iron ore slurries. Besides online elemental analysis, the analyser can be combined with optical measurements for rapid continuous measurement of each sample line. Laboratory testing has also shown potential for mineralogical analysis using the combination of LIBS and reflectance spectroscopy.CITATION:Koresaar, L, Khajehzadeh, N, Haavisto, O and Timperi, J, 2017. Online elemental and mineral measurement of slurries in iron ore beneficiation, in Proceedings Iron Ore 2017, pp 561–566 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Laura E. Beverage

The Changes 2008 Brought -MSHA recently posted a PowerPoint to its website which shows statistical performance information for fiscal years 2000 to 2008. -Interesting statistics: Fatality rate in Coal dropped by nearly 30% (.0348 to .0246 per 10,000 workers)

Jan 1, 2009

By Gabriel Esterhuizen

Underground stone mines in the United States make use of the room-and-pillar method of mining. A prerequisite for a safe working environment is that the pillars should adequately support the overburden and the pillar ribs and rooms should remain stable during mining. At present pillar dimensions are either based on experience at neighboring mines or on strength equations that were developed for metal or non-metal mines. This paper presents a pillar design methodology that was developed from a study of pillar performance in operating stone mines. Data were collected that describe the rock mass quality, pillar conditions, mining dimensions and intact rock strength. The results showed that current mining practices have resulted in generally stable pillar layouts with no recent cases of extensive pillar collapses. However, a small number of single failed or failing pillars were observed in otherwise stable layouts. Numerical analyses were used to supplement the observations and develop a pillar strength equation that describes the stable and small number of failed pillars observed. The developed strength equation can be used to design stable pillar layouts provided the factor of safety is greater than 1.8 and the width-to-height ratio of the pillars is greater than 0.8. The paper concludes with guidelines for applying the developed equation and selecting appropriate input parameters.

Jan 1, 2008

By W. Collingwood

As open pit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in open pit mines is often recirculatory. This recirculation traps dust and gases in deep open pit mines. This problem is particularly acute in high latitude open pit mines due to a phenomenon known as an atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In open pit mines, this can result in unhealthy accumulations of gases and other contaminants in the open pit mines. In this study, the natural wind flow patterns in and around open pit mines were investigated using a computational fluid dynamics (CFD) program. Two dimensional models were created for a variety of pit geometries. The effect of depth, slope angle, and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2011

By Jan C. Still

The Haines-Klukwan-Porcupine subarea of the Juneau Mining District (JMD) is located in the northern portion of the JMD and consists of the land between the Alaska-British Columbia boundary, the Chilkoot Valley, Glacier Bay National Park boundary, and extending south to the Davidson Glacier and the Chilkat Peninsula and Islands (fig A-I). This area was studied as part of the larger JMD study in a cooperative effort between the Alaska Division of Geological and Geophysical Surveys (ADGGS) and the Bureau during 1985 to 1988. Prior to this, during 1984, the ADGGS and the Bureau cooperated in a study of the Porcupine mining area and during 1981 to 1983 conducted separate studies in the area. Field work was conducted by foot, boat, truck, and helicopter. Figure A-I shows the Haines-Klukwan-Porcupine sub-area and shows the areas covered by previous Bureau and ADGGS studies. PHYSIOGRAPHY AND CLIMATE The physiography of the subarea ranges from gentle to rugged. Glaciers formed the major features in the sub-area and left "U" shaped steep walled valleys and rugged mountains. The Chilkat, Chilkoot, Klehini, Tsirku, and Takhin are the major rivers in the subarea. The higher mountains are glacier clad and some valleys still harbor glaciers that reach the valley floors. Lush forests and dense brush predominate up to timberline at about the 2,000-foot elevation. Low point in the subarea is at sea level in the area around Haines while the high point is 7,434 feet at: Mount Henry Clay in the Porcupine mining area.

Jan 1, 2012

By Nelver Benavides

"Actualmente en la industria minera, las técnicas de control avanzado, la integración de procesos y tecnologías ya no son consideradas como conceptos exóticos y de dudoso impacto productivo, sino solo como un eslabón más en el proceso de mejora continua. En ese sentido, el presente texto señala la integración de estas tecnologías en la Concentradora Cuajone – Southern Perú, considerando las operaciones de chancado, molienda, sistemas de recuperación de agua y proyectando expectativas a mediano plazo para las operaciones de flotación, extracción y voladura. "

Sep 12, 2011

By Lucas Lopes da Costa

In this work, a natural foam extracted from the Amazon buriti palm tree is investigated as possible substitute for synthetic foams. The basic physical and mechanical properties of this biofoam were evaluated. Its sponge-like structure was characterized by the amount of pores and morphological aspects. It was found that the buriti biofoam displays a very low density of the order of 0.1 g/cm3 with a relatively good compressive strength. This would be suitable for several engineering applications and as a new material with the potential for replacing currently applied synthetic polymeric foams.

Jan 1, 2010

By Richard A. Cubeta

Precast concrete segments have been used in sanitary sewer tunnel design for decades. Federal mandates (reduction in heavy metals and I & I), and system design changes (increased retention times) and other factors have exacerbated corrosion problems. In an effort to combat the ever-growing effect of microbiologically induced corrosion, owners, engineers, and designers have been specifying thin-film lining systems to protect precast concrete segments. These systems have compatibility and installation issues. Chemical additives or calcareous aggregates have been utilized in precast concrete, but have only proven to retard the rate of corrosion and do not eradicate the problem. Solid cast polymer segments are stronger than precast concrete, do not require linings or coatings, are impervious to ground water infiltration, and, above all, are inherently corrosion resistant through and through.

Jan 1, 2008

By Carlos Soria

El presente texto describe los Sistemas de Gerencia de la Información y su aplicación en la industria minera con el objetivo de optimizar la gestión total de la empresa. Dichos sistemas manejan información del proceso y sus valores de producción, cálculos, consumos de energia, emisiones de plantas, tiempos de funcionamiento de equipos, eventos, alarmas, mediciones de laboratorio y control estadístico, etc. De forma que dicha información pueda ser reunida y consolidada, convirtiéndose en materia de significado y relevancia disponible en base a análisis, reportes, listas, tendencias y gráficos para que el usuario final de una planta o en sus oficina pueda tomar mejores decisiones.

Jul 17, 2000

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, whereas in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600?1000°C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed. For over 60 years, Outotec has progressively been developing the principle of fluidized bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidized bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

In 1962, minerals beneficiation showed definite signs of coming out of the doldrums into which it has drifted after the uranium boom. Demand by steelmakers for high-grade iron pellets has created the need for concentrating plants to upgrade specular hematite by spiral concentration or flotation and magnetites by magnetic means and flotation. According to a paper given at the AMC annual meeting by C. S. Arms of Pickands Mather, "the shipment of pellets, started in the mid-1950's, has increased to 17.6 million tons in 1961 from North American operations. Many plants already underway will raise this production to about 42 million tons by 1965. This will be a very sizeable percentage of the total iron ore production contemplated by that date." Iron ore concentration methods are gradually raising the assay of pellets into the 65 to 69% Fe range and lowering silica to the 4 to 7% range. Quebec Cartier's Lac Jeannine concentrator went into operation in late 1961 and all grinding units were running by 1962. The Iron Ore Co. of Canada's new Carol Lake plant was started in mid-1962.

Jan 2, 1963

By Mike Robotham

When RFQ?s are received they often contain detailed technical specifications which suggest a departure from the suppliers own customary approach to the design. Both client and end user are quite rightly influenced by their own experiences. The question is who is right, the client and his consultant, the supplier or perhaps a combination of these. This paper looks at some of the fundamental variances that often occur in the approach to the mechanical design of drum hoists, based on our experiences of recent years. Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2011

Suggestions have been made at various times that there may be a recurrence of lodes similar to those at Kalgoorlie in the country to the south of the Golden Mile, but, so far as is known, there has been no geological evidence to support these suggestions apart from the possible extension of the younger quartz-dolerite greenstone in this direction.Geological mapping carried out by the writer in the Coolgardie district in 1946, provided some additional geological evidence to support this claim, and the ideas then held have since been expanded and are now considered to be sufficiently advanced to present them as concrete suggestions. As will be seen from the following pages, the critical area for lode prospecting is Hannan's Lake, where the basement rocks may include younger quartz dolerite greenstone, which, although perhaps distributed over a smaller area than at Kalgoorlie, could, on structural grounds, have a similar fracture system and similar ore deposition.There is little need to stress the importance discoveries in this area would have in prolonging the life of the field, and stimulating the post-war gold mining revival.Previous Work: Only the publications having a direct bearing on the preparation of this paper are given in the list of selected references, but the writer is very conscious of the fact that much other geological work has been carried out in the Kalgoorlie district since its discovery, by the W.A. Department of Mines, by mining companies, and others, all of which has contributed to the present knowledge of the field, and acknowledgment of the value of this work is given herewith. In presenting the suggestions in this paper a broad structural control of ore deposition is assumed, but this has already been established in other parts of the goldfields of Western Australia, including adjacent areas. In the early nineteen thirties, the Western Mining Corporation commenced work on the basis that there was a close relationship between geological structure and auriferous ore deposition, and a similar approach was first made by the Geological Survey of Western Australia in the South Yilgarn in 1935. These ideas were further developed during later surveys, particularly in the North Yilgarn and the Mount Margaret Goldfield.During the Coolgardie Survey in 1946, broad structural mapping was done in greater detail than before, and the structural ideas were implemented and further developed, leading to some success.Other work to which particular acknowledgment is given is that of Stiltwell, Gustafson and Miller, Forman, Prider and Finucane, at Kalgoorlie, and that of Honman in the Kalgoorlie-Coolgardie district, references to which are given at the end of this paper.Valuable constructive criticism of this paper has been given by Professor E. de C. Clarke and Dr. R. T. Prider, of the University of Western Australia.

Jan 1, 1950

By S. Y. Tan

The thermal stability of fully silicided NiSi with arsenic doping on silicon was investigated. The aims of the work were to investigate the Ni silicide phase-related issues associated with arsenic dopant and thermal annealing on Ni-FUSI/HfO2/Si and Ni-FUSI/HfSiO/Si gate stacks. It was found that arsenic-incorporation demonstrated some improvement in both morphology and phase stability of nickel silicided films at high processing temperatures regardless underlying gate dielectrics. The correlations of Ni-Si phase transformation and arsenic doapnt with their electrical and physical changes were established by sheet resistance measurements, X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, the modulation of the work function (WF) of Ni fully silicided gates by arsenic impurity is presented, comparing the effects of dopant (As) on the WF and silicide phases (NiSi and NiSi2). It confirmed that the work function of NiSi can be tuned by implanting arsenic dopant, but it ineffective for NiSi2 phase.

Jan 1, 2010

Experimental results are presented for the anode overvoltage as a function of current density for different alumina concentrations in an alumina reduction cell. Voltage changes due to the electrolyte resistance and also the decomposition voltage, have been evaluated as a function of alumina concentration and anode current density. From these values of voltage, changes in the total cell voltage have been derived for changes in alumina concentration for different anode current densities. The results show that for each operating current density there exists a discrete alumina concentration that defines a minimum reduction cell voltage. Discussion is made about potential savings in power consumption when the alumina concentration is controlled.INTRODUCTIONThe standard procedure in the aluminium industry when analysing the cell-voltage required for the Hall-Heroult process for reduction of alumina, is to subdivide the total voltage into the following components (e.g. Pearson, 1955; Maritell, 1960).1. ohmic drop through busbars and joints2. ohmic drop through cathode lining3. ohmic drop through anode4. ohmic drop through electrolyte5. overvoltage at anode6. electrolytic decomposition voltage.(Overvoltages ,at the cathode are of negligible magnitude at all practical current densities.)It is understandable that the voltages assigned for each factor invariably differ for different workers...

Jan 1, 1965

By Alonso Marchena, William Martínez, Joel Otero

En Arequipa, Moquegua y Tacna se han definido diversos arcos magmáticos. En los arcos jurásico, paleoceno y oligo-mioceno ocurren pórfidos de distintas características, los cuales presentan diferencias litogeoquímicas (LaN/YbN>20, Sr/Y>40, Eu/Eu*>1, U/Th>0.27, NbN/TaN>0.7). Estos parámetros pueden ser utilizados como guías de exploración, ya que son anomalías desde el punto de vista litogeoquímico. En caso no haya mineralización visible (depósitos ocultos), el empleo de estos trazadores en unidades ígneas (diques, cuerpos subvolcánicos e intrusivos) puede señalar la probabilidad de encontrar depósitos en profundidad.

May 22, 2019

By Andrew Howard

As the mining industry moves further into developing countries in search of new resources, its role in international development is coming under increasing scrutiny. This is a trend that is likely to accelerate, along with the potential for headaches among managers in the industry. Public interest in development and environmental issues is rising as faith in “big business” falls. This has strengthened nongovernmental organizations (NGOs) campaigning for sustainable development. And it has put more pressure on banks, governments and development agencies to curb corporate misdemeanors. Developing world governments are also becoming emboldened to reject previously agreed terms they do not consider equitable. The mining industry has begun to formulate a response to these pressures but must go much further. Societal and environmental issues must move from public relations to core strategic thinking. Abiding by rules or codes is not a relevant response. Instead, genuine support for sustainable development is required. This will involve delegating the responsibility for engaging with local communities to on-the-ground staff and developing a dialogue with local stakeholders rather than conducting an initial assessment and disengaging.

Jan 1, 2006

By F. Petkovich, M. P. Sudbury

Development of a new method of treating flotation concentrates for the preparation of feed suitable for direct charging to blast furnaces or converters is described. The method takes advantage of the fact that pyrrhotite contained in the concentrates can be made to undergo exothermic reactions which, under properly controlled conditions, result information of oxidation products that serve to cement the concentrate particles together. Thus green concentrates either in the form of pellets or briquettes containing 5 to 8 pct moisture not only were hardened, but also completely dried autogenously by continuous countercu,vrent shaft treatment with air. The process was developed through pilot plant operations ranging from 35 1b per hr to 2.5 tph, culminating in products evaluation tests on a railway-car scale. Falconbridge Nickel Mines Ltd., Falconbridge, Ont., have practised sintering, on a travelling grate machine, for many years to prepare a pyr-rhotite-bearing Cu-Ni sulfide flotation concentrate for blast furnace smelting. In recent years the development of new mines, and the construction of concentration plants some 40 miles from the smelter has increased the quantity of concentrate shipped, and encouraged the search for a method of producing dry, hard pellets or briquettes suitable for direct charging to a blast furnace or converter, and capable of withstanding considerable handling. The cementing properties of pyrrhotite oxidation products were discovered during a search for a suitable agglomeration method for sulfide concentrates, and were exploited in a process subsequently developed for autogenously drying and hardening pellets and briquettes of pyrrhotite-bearing Cu-Ni sulfide flotation concentrate. EARLY TEST WORK The production of hard, dry pellets of concentrate filter cake was attempted in the drying plant of one of the new concentrators. While soft pellets were produced containing 5 pct moisture, attempts at further drying resulted in disintegration of the pellets and intolerable dusting. The plant therefore was controlled to produce a concentrate containing about 6 pct moisture. The partially dried concentrate, which was shipped to Falconbridge for sintering, tended to heat spontaneously in transit. An at- tempt to briquette the moist concentrate at Falconbridge, in a plant incorporating a muller, a 20-in. roll briquetting press, and a steam-heated travelling grate oven, was more successful, although the equipment corroded rapidly due to the acid nature of the concentrate after spontaneous heating had occurred. LABORATORY STUDIES OF SPONTANEOUS HEATING OF CONCENTRATE The spontaneous heating of partially dried concentrate was studied in the laboratory. Moist concen-

Jan 1, 1961

By Sumner M. Anderson

Any discussion of outside support to Latin American mineral industries must concede at once the pre-eminent role of U. S. industry and business. American capital has developed the great copper resources of Chile and Peru, the lead-zinc of Peru and Mexico, the bauxite of Surinam and Jamaica, the petroleum and iron ore of Venezuela. American consumers have provided the market for their products. U. S. companies operating south of the border have trained Latin American geologists, engineers, chemists, and skilled labor—including metal, mineral, and fuel technicians—to new and greater competence. The industrial demands of World War II drastically altered world economics and concepts of U. S. foreign mineral requirements. In this country discovery of vital mineral resources fell far behind the alarming depletion rates, and there was new appreciation of the actual and potential importance of the world's less extensively explored areas. During the war and afterward, the task of supplying the nation's mineral requirements became greater than private industry could carry alone, and the Government assumed a position of continuing support. In Latin America, as elsewhere, this support applies in three categories: banking, procurement, and technical assistance. The first two are now generally accepted as necessary Government functions; the third has often been misunderstood and misinterpreted, although it has given rise to legitimate controversy. There have been major accomplishments in all three categories, as well as some errors of judgment. Since the beginning of World War 11, U. S. Government financing, procurement, and technical assistance have been applied on a large scale to a wide range of commodities and services throughout the free world. The present discussion—under the separate headings mentioned—will concern only the support related to a single industrial group in a single geographic area. During the War Federal banking was conducted on an emergency scale by temporary agencies created to meet the abnormal circumstances. Unfortunately, there are no readily available data on these activities that would permit evaluating loans and credits extended for mineral projects in Latin America. The only agency operating in this field since World War II is the Export-Import Bank, under its own authority and to some extent from credits authorized by the Office of Defense Mobilization. The Bank can offer more capital—on more favorable terms—than is available from most Latin American banks, and its staff of engineers evidently can appraise loan applications more favorably than commercial banks in this country are willing to do. The risks seem to be justified, as defaults have been well under 1 pct of total loans. From V-J day 1945 to the end of 1957, mineral loans to Latin America have been authorized for projects totaling $541.63 million in eight countries. In order of magnitude of credits, they have been made to Brazil, Peru, Chile, Mexico, Argentina, Venezuela, Guatemala, and Bolivia. In order of magnitude by industries. they are for development and expansion of steel mills, copper, manganese, nitrate plants, iron ore, zinc plants, sulfur plants, cement plants, tungsten, coal, and lead. Loan Distribution: By far the largest loans have been $307.9 million for iron and steel projects in Brazil, Chile, Mexico, Argentina, and Peru: $100.4 for developing the great low-grade copper deposits of southern Peru; and $55.3 million for developing manganese deposits in the Territory of Amapa, Brazil. Others range from $20.8 million for a zinc smelter in central Peru to $19 thousand for iron-mine trucking equipment in Chile. It has been noted that 59 pct of the loans have been to foreign companies, 14 pct to companies of mixed foreign and American capital, and 27 pct to American mining companies. About 40 pct of the total authorizations has been disbursed so far. In addition to these amounts, the Strategic Materials Division of the Economic Cooperation Admin-

Jan 1, 1959