Search Documents

Jan 1, 1998

By Christopher J. Bise

INTRODUCTION Traditionally, the purpose of mine ventilation has been defined as diluting, rendering harmless, and sweeping away hazardous gases which may accumulate in the mine workings. In addition, the ventilation sys- tem must keep the mine air as close as possible to the composition of the outside air in order to provide a healthy environment for mineworkers and to prolong the useful life of mine equipment. When plans are being developed for opening a new mine, sound engineering dictates that a calculated estimate be made of both the maximum air quantity requirement and the accept- able mine pressure (head) loss related to the under- ground layout and projections. For efficient mine ventilation, the two problem areas that demand constant attention are (1) the control of fugitive air (through short circuiting or leakage) and (2) the provision of ample airway capacity. Fugitive air is that quantity of air which enters the mine but short-circuits the mine ventilation system through improperly constructed stoppings, doors, overcasts, etc.; it represents an investment in power consumption (to move the air by the fan) while providing little, if any, return on the investment. Typically, efficient mines are those that can deliver 50% of the air handled by their fans to the working faces. Paying close attention to a new mine's ventilation system at the outset can provide numerous benefits during the later stages of mine development. It has often been noted that the main cause of trouble in many mine ventilation systems can be found within a radius of 2500 ft from the fan installation. Ample airway capacity is essential to maintain the mine's head loss within manageable limits. Similar to an industrial ventilation setting, the mine's headings are the ductwork for the handling of air. The difference between normal industrial ventilation and mine ventilation is apparent when more capacity is needed; a plant can install new or larger ductwork, but it is difficult for a mine to install new entries or enlarge existing entries. Air velocities are usually maintained under 800 fpm to limit the stirring up of dust in the intakes. With this in mind, it is usually simple to estimate the number of entries required in the ventilation system. The problem that often arises, though, is when the system's capacity is overestimated and the required head loss to achieve the desired quantity is excessive. Experience has shown that problems are often encountered when the mine's condition requires much more than three inches of water gage to ventilate the mine on a day-to-day basis. Thus, if proper attention is not paid to these parameters in the preplanning and initial development of a new mine, it may take an extremely high water gage to achieve the ultimate quantity. This chapter will not delve deeply into the theory of mine ventilation; many other books have been writ- ten on that subject. Instead, the following sections will point out the important considerations that should take place before the development of a mine ventilation system, as they relate to normal industry practice. FUNDAMENTALS OF AIRFLOW Volume Versus Water Gage The common method of measuring ventilation pressure is in terms of inches of water gage (wg); one inch of water corresponds to a pressure of 5.2 psf (pounds per square foot). Further, airflow follows a square-law relationship between volumes and pressures where, as shown in the previous section, a doubling of quantity requires a quadrupling of pressure. Table 1 shows how heads and quantities are related. Using Table 1, it is readily apparent that, for the same mining conditions, an increase in pressure from one inch wg to three inches wg results in only 34,640 cfm when the initial quantity is 20,000 cfm. Pressure Losses Pressure losses in mine ventilation systems are caused by friction between the heading walls and the air stream and by shock losses due to abrupt changes of the air stream caused by obstructions. The common pressure-loss formula for mine ventilation is: [ ] where H is the pressure loss in inches of water gage, K is the coefficient of friction, L is the length of the airway in feet, 0 is the airway perimeter in feet, V is the air velocity in feet per minute, and A is the cross-sectional area of the airway in square feet. Table 2 lists the US Bureau of Mines schedule of friction factors (K) for mine airways. Recent research indicates that the values of K are slightly less for coal mines than those presented in the USBM Schedule, and Table 3 should be consulted in this instance. It should be

Jan 1, 1986

Pressure drops were measured in a column packed with glass spheres and wax particles, both in random and preferential distributions. Variables investigated included wax content, gas flow rates, and temperatures.It is shown that for random distribution of wax, pressure drop is exponentially related to wax content above the melting point of wax and that below this it increases with increasing gas rate and temperature.For preferred distribution of wax the highest increase in pressure drop is obtained with horizontal distribution of wax and the least with vertical distribution.Comparison with operating blast furnace data and application of results to practice are also included.

Jan 1, 1970

Owing to the number of chemical processes now in use for the separation of metals from their ores, and the consequent employment of chemicals at the mine, it is sometimes necessary to be able to produce them on the spot. This particularlyapplies to sulphuric acid which may be required for the manufacture of chlorine and of sulphate of copper, or for the treatment of'sulphides and other purposes. It can be made from brimstone for rather less than £3 per ton, but when delivered to any distance from the works, the cost of packages and other charges would amount to more than the value of the acid.I hope therefore, that to any of the members of the Institute who may find it necessary to make sulphuric acid for their own requirements an outline of the process, and some details of the plant etc may be useful, and perhaps lead to their devising improvements, mechanical or otherwise. Though acid can be made from pyrites in Europe for about 15/- per ton, it is probable that for most metaIIurgical purposes the quantity required. and the uncertainty as to how long it would be needed, would make it advisable to spend as little as possible on plant, and so use brimstone, though more expensive, I have therefore given no details of pyrites burning, which is very fully treated by Prof, Lunge in his work on " Sulphuric Acid and Alkali."

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Benoît Demers

Dans ses opérations de traitement de concentré de zinc, l?usine de Zinc Électrolytique du Canada à Valleyfield génère un résidu minier appelé « jarosite ». Jusqu?en 1998, le jarosite était transporté hydrauliquement dans des bassins construits en argile. Le jarosite sédimenté possède une consistance très molle (impossible de circuler à pied sur le résidu consolidé) avec une eau interstitielle acide contenant des teneurs élevées en métaux. Ces caractéristiques particulières au jarosite rendaient très coûteuses la construction et la fermeture des bassins de résidus. En 1998, Zinc Électrolytique du Canada a implanté un nouveau procédé, développé chez Noranda, dont le principal objectif était de stabiliser chimiquement et physiquement le jarosite. Un nouveau concept de déposition a été élaboré pour le nouveau résidu minier appelé « jarofix ». Les grandes caractéristiques du nouveau procédé et du concept de déposition sont : ? Le jarosite est lavé et déshydraté à l?usine avec un système de filtre; ? De la chaux, du ciment et de l?eau sont ajoutés pour former le jarofix; ? Le jarofix est transporté par camions jusqu?à l?aire d?accumulation; ? À l?aire d?accumulation, le résidu est géré selon un concept d?empilement. L?élaboration du concept d?empilement et de l?aire d?accumulation devait tenir compte des caractéristiques de déposition du jarofix, de sa résistance à l?érosion hydrique et éolienne, de la gestion de l?eau de ruissellement, de la faisabilité de construire les digues de ceinture en utilisant du jarofix durci et de la nécessité de restaurer progressivement l?aire d?accumulation. Le déchargement du jarofix se fait à partir d?une rampe qui progresse avec une pente ascendante pour développer un front de déversement de plus en plus haut. La hauteur du tas de jarofix atteindra 30 m au centre du site. L?aménagement initial de 1998 a inclut une digue d?amorce de 3 m de hauteur, une rampe de déversement de 8 m de hauteur et un bassin pour la gestion de l?eau de ruissellement. Les propriétés du jarofix consolidé dans l?aire d?accumulation sont déterminées annuellement. Le jarofix durci possède la consistance et la résistance d?une argile très raide. Sa conductivité hydraulique est similaire à celle d?un silt et il résiste bien à l?érosion éolienne. Après trois années de déposition, la température du jarofix au milieu du dépôt demeure élevée. Le jarofix durci est facile à excaver et à compacter, ce qui en fait un excellent matériau pour la construction des digues de ceinture en périphérie du site.

Nov 1, 2002

By R Munoz, R González, J Vallejos, A Delonca

In panel caving in underground mines, it is essential to characterise and monitor the stress and stability state of production level pillars to ensure the extraction of the mineralised ore column and the safety of workers. Pilar Norte is a sector in the El Teniente mine that forms a pillar between the undercut fronts of the adjacent Esmeralda and Reservas Norte sectors. It exists in a high-stress environment, which may induce damage to the rock mass production pillars. Generally, numerical models are calibrated using observed damage in galleries. This procedure does not discriminate between the structural condition and/or the blasting damage effects. This paper proposes a technique that uses borehole cameras to measure stress-induced damage. This has the advantage of being at the intact rock scale, meaning that the effect of geological structures is negligible and the blasting damage factor is eliminated. Comprehensive geotechnical characterisation and tomography monitoring has been undertaken at Pilar Norte to describe and determine the rock mass behaviour of the production pillars. By combining analytical, empirical and numerical models, a correlation between the measured overbreak recorded by the borehole cameras and the stress level of the pillar was developed. The methodology can be routinely applied to estimate the stress state in the production pillars.CITATION:González, R, Munoz, R, Vallejos, J and Delonca, A, 2016. Characterisation and monitoring of the stress state of production pillars at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Henry A. Signore

The Appalachian coalfield, located in eastern Kentucky, Pennsylvania, Virginia and West Virginia, has been one of the most productive in the United States. Total production from the Appalachian coalfield during 1994 was 340.8 Mt (375.4 million st), or 37% of the 929 Mt (1 billion st) produced in the United States that year. This region contains various coal types from high- to mid-sulfur coal in Pennsylvania and northern West Virginia to low-sulfur, compliance steam coal and premium-grade metallurgical coal in eastern Kentucky, Virginia and southern West Virginia. The region's product is in high demand in domestic and export markets. Productivity continues to improve, resulting in the primary coal operators solidifying their market positions.

Jan 1, 1995

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

Sluiceboxes can provide a much higher concentration ratio than most other gravity concentrators (up to 50 000:1) at very high overall placer gold recoveries (greater than 99 per cent). They are also very reliable, inexpensive and simple to operate. This combination is very difficult to beat and explains why the sluicebox is still the most important placer gold concentrator in northwestern Canada, Alaska and the rest of the world. A sluicebox is a rectangular fl ume containing riffles on matting, through which a dilute (<12 per cent) slurry of water and alluvial gravel flows. Sluiceboxes are actually centrifugal concentrators with settling velocity playing a minor role in gold recovery. Due to their higher density, gold particles tend to segregate to the bottom of the slurry flow where they form a streamline that is diverted by a low pressure zone into a riffle. Under ideal conditions, this ribbon of slurry will be overturned as it flows down the rear of the following riffle and will continue fl owing in a circular path to form a vortex. At the bottom of this vortex, centrifugal and gravitational forces combine to drive gold particles into or beside the matting. To remove the gold concentrates, sluiceboxes are shut down and the riffles and matting are taken apart and cleaned. The slurry velocity provides the energy that powers the vortex. If the velocity of the slurry is reduced through overloading with solids, insufficient water flows or shallow gradients it may not sustain a full size vortex. If the riffles are too close, too far apart, too tall, or if there is not enough energy available to the vortex, the vortex will not be formed properly and gold recovery will be reduced. If the slurry velocity is too high, extreme turbulence and the resulting scouring will also cause gold losses. Testing sluiceboxes with conventional sampling and evaluation techniques is very costly, time consuming and problematic. Most placer gold ores contain a very small number of gold particles in a large volume of pay gravels. Sluiceboxes can lose coarse gold particles. The presence or absence of one of these particles in a tailings sample can lead to high unpredictable errors (nugget effect) even when large sample volumes are processed with care. Every time conventional samples are upgraded, additional errors are introduced due to the inefficiency of recovery equipment. Nuclear tracer tests are more accurate, faster, cheaper and safer than conventional sampling. In 1989 through 2002, the recovery efficiency of dozens of sluicing systems was determined by mixing radioactive gold particles (tracers) into the feed streams of dozens of placer mines in the Yukon Territory, British Columbia, Alaska and Guyana. Four distinct sizes of nuclear tracers were used and their recovery was related to the design and operational characteristics of the individual sluiceboxes and their pay gravels. At clean up, scintillometers were used to detect the very low level X-ray and gamma ray radiation emitted by these tracers and locate them in the sluice runs. The effectiveness of any given section of riffles was easily diagnosed by the presence or absence of tracers. At every mine the gravel feed rates, water flows, equipment dimensions and riffle performance were measured. After the gold tracers were removed from the fi nal concentrate and counted, the concentrate was sieved and weighed. These gold recovery, weight and sieve data were used to calculate the quantities and size distributions of the gold particles in the original pay gravels and those lost in the tailings. The expired tracers were stored in a lead lined container until their radioactivity was near background levels (about two months). The standard errors from these radiotracer tests were estimated from binomial probability theory with the equation: SE = {(n + p + q) ^ 0.5}/n. Where n was the total number of radiotracers added, p is the proportion recovered and q was the proportion lost. Each overall recovery estimate would be within one standard error of the true recovery value (14 times out of 20) and almost always within two standard errors of the true recovery (19 times out of 20). The maximum standard error with 100 tracers was five per cent and occurred when the recovery approached 50 per cent. With higher recoveries, standard errors usually ranged from one to two per cent.

Aug 1, 2010

By William G. Hedling

The operation of electric face equipment in underground coal mines has proven to be extremely hazardous to mining personnel, including equipment operators and others working in the vicinity of active equipment. Recent industrial engineering studies* of accidents and fatalities indicate that a major contributor to this hazardous situation is noncompliance with modern principles of human engineering, particularly lack of standardization of control configurations. Control configurations differ not only among different machine types, but also among the same machine types produced by different manufacturers. This lack of standardization can produce a high incidence of error in the operation of electric face equipment, thus creating a potential source of accidents. Other examples of non-compliance with human engineering principles are the widespread use of identical black, round control knobs (regardless of the function being performed), and the inappropriate location, spacing, and labeling of controls. Any or all of these factors may place the operator in a "negative transfer" situation, which means that control manipulations appropriate for one type of machine are different from (or even the reverse of) the control movements required to produce the same effect on other machine types. This situation increases the accident potential to the operator, as well as to others in the vicinity. Accident potential is further increased by circumstances which do not allow for large error tolerance-specifically, emergency procedures. Reports of accident statistics cite operator inexperience as a primary cause of most accidents involving underground electric face equipment. Several factors contribute to operator inexperience, including: 1. High personnel turnover 2. Employee absenteeism 3. Current union practice of bidding for jobs.

Jan 1, 1974

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By D M. Marques, J F. C L Costa

The estimation of process plant head grade is not trivial and is a source of constant dispute within the mining industry. Grade estimates informed by the short term mine planning are frequently not reproduced by sampling the continuous flow of ore at the plant. Head grades are normally obtained by periodically sampling the continuous flow during a day or shift, and taking the average of the multiple increments collected. The standard error of this mean grade depends on the ore variability and the frequency (number) of aliquots extracted. The more increments are taken the higher is the precision on the calculated mean. Variographic experiments are normally used to map grade variability along a certain period of time and the extension variance is derived from this variogram. This experiment is time consuming, expensive and cumbersome. Mining industry personnel rarely apply this approach. Additionally, a temporal variogram can vary from day to day as different ores are mined along the life of the mine. This paper investigates a novel approach based on simulating the grades feeding the processing plant. In situ 3D grade models are built using geostatistical simulations. Grade spatial continuity and variability are reproduced in models that mimic the real deposit. These models are used in mine planning and scheduling transforming a 3D block model into an one dimensional string of values feeding the plant (one dimension flow). These grades have the statistical characteristics of the unknown real grades and can be sampled to emulate a variographic experiment. The results showed consistency and adequacy to estimate the sampling error (Gy, 1998 p 31) for various sampling intervals using the simulated grades. Also the results show a variographic experiment can change significantly from time to time, as ore changes and a selected sampling protocol can become obsolete if not adjusted for ore variability.CITATION:Costa, J F C L and Marques, D M, 2012. Defining a sampling strategy for a continuous flow supported by geostatistical simulations, in Proceedings Sampling 2012 , pp 3-8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Alana Pereira Ramos

O efeito de memória de forma tem como principal objetivo a recuperação da forma por meio de aquecimento acima das temperaturas críticas de transformação. Fitas da liga Ti43,5Cu37,8Ni18,7 foram preparadas através do processo melt spinnig com velocidade da roda de 21 m/s e 63 m/s. As fitas foram tratadas termicamente numa temperatura de 700°C por 15 minutos em forno e resfriadas ao ar. A caracterização das fitas foi feita por calorimetria diferencial de varredura (DSC) e análise por difração de raios X (DRX). Foi observado que com uma menor velocidade de rotação da roda (21 m/s) a fita apresentou-se totalmente cristalina, e quando aumentou-se a velocidade linear da roda para 63 m/s a fita apresentou-se completamente amorfa. Após o tratamento térmico todas as fitas apresentaram as transformações martensíticas e auteníticas. Observou-se que a velocidade da roda tem grande influência nas temperaturas de transformação, chegando à variação de aproximadamente 7°C. O tratamento térmico remove todos os defeitos produzidos pelo processo de solidificação rápida e produz um rápido crescimento de grão, favorecendo ao aumento das temperaturas de transformação.

Aug 8, 2018

By Steven K. Duke, Jay Arabshahi

An economic, real-time probe drill monitoring system was developed for Metropolitan Water District’s Arrowhead Tunnels project to quantitatively evaluate ground conditions ahead of a TBM. This system digitally records hydraulic feed, rotation, and percussion pressures and calculates drill advance rates during drilling. These data are computer synthesized to develop a digital representation of the ground ahead, and the resulting “picture” of the ground is distributed to the project team to assist with tunnel construction decisions (i.e., targeting grout holes, optimizing mine-cycle lengths, and avoiding becoming stuck). The analysis and interpretation procedure has now been calibrated and refined using over 5,000 m (3 miles) of geologic face mapping data.

Jan 1, 2007

By R. W. Van Dolah

A premature detonation of an explosive charge occurred on January 30, 1961, at a face being prepared for blasting in the underground Jefferson Island Salt Mine, Diamond Crystal Salt Co., Jefferson Island, Iberia Parish, La. The accidental blast injured the powderman fatally; his helper was injured also, but recovered. The accident represents the first fatality reported to the Bureau of Mines in connection with the use of ammonium nitrate-fuel oil (AN-FO) blasting agents in underground mining in the United States. Representatives of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activity conducted the investigation, upon request of the manufacturer of the ammonium nitrate being used and with concurrence by the mine management.

Jan 1, 1962

By H. Lawson

The Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03in April of 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib, and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB 09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2012

By J. P. Rider

Operating practices and resulting production from longwall faces are continually improving. Consequently, longwall operators are continually seeking to improve the dust control capabilities on longwalls. The National Institute for Occupational Safety and Health (NIOSH) has been conducting dust surveys at longwalls throughout the country in an effort to document the types of controls that are being used and to quantify the relative effectiveness of these controls. To date, surveys have been completed at longwalls in Alabama, Colorado, Pennsylvania, Utah, and West Virginia. In addition NIOSH has been reviewing longwall dust parameters provided by mine operators to MSHA to assess the status of dust control technology being used throughout the industry. Results from the underground dust surveys and information obtained from MSHA will be summarized in this paper to provide an update on longwall dust control technology and practices.

By T. Celik, B. Genc, C. Musingwini

"This paper discusses a new methodology for defining and measuring mine planning software utilization in the South African gold mining sector within an evolving data-set framework. An initial data-set showing the mine planning software providers, their corresponding software solutions, as well as the software capabilities and information on the number of licences was collected and compiled in 2012 in an online database for software utilized in the South African mining industry. Details of the database development and implementation were published in the Journal of the Southern African Institute of Mining and Metallurgyin 2013. In 2014 the data-set was updated with additional and new information. Using the 2012 and 2014 timestamps, a methodology for estimating the software utilization was developed. In this methodology, the three variables of commodity, functionality, and time factor were used to define and measure the software utilization in order to ultimately inform decision-making strategies for optimal software utilization. Using six different functionalities, namely Geological Data Management, Geological Modelling and Resource Estimation, Design and Layout, Scheduling, Financial Valuation, and Optimization, utilization in the gold sector was measured. This paper presents the methodology employed for measuring the mine planning software utilization. The methodology is useful for stakeholders reviewing existing software combinations or intending to purchase new software in the near future and who want to estimate the comparative attractiveness of a certain software package. These stakeholders include mining companies, consulting companies, educational institutions, and software providers. The work presented in this paper is part of a PhD research study in the School of Mining Engineering at the University of the Witwatersrand."

Jan 1, 2015

By A. Raja, C. C. Harris

Apparatus for maintaining constant — but adjustable — pulp level and rate of froth removal are described. The results of preliminary experiments into the effect of scraping speed on the rate of solid and liquid recovery with a semi-batch system are presented. Glass spheres restricted to a narrow size range is the solid under investigation. Graphical methods for estimating the mass of recoverable material and the zero error are given. The semi-batch procedure1 is extensively used in laboratory flotation testing, though the method is subject to variability of moderate severity. Raffinot2 concluded from a statistical study of the difference between replicate tests, that the ptincipal source of errot was the test itself and not sampling or chemical analysis. These differences can be ascribed principally to changes in pulp volume and reagent concentration, and uncontrolled rate and depth of scraping. Semi-batch testing has been criticized1 on these grounds as a means of investigating flotation kinetics. This paper discusses and describes modifications to laboratory flotation equipment which reduce the number of manual operations and lead to improved control. Kinetic studies were the primary reason for developing the apparatus described. It should, however be a useful aid in normal flotation testing. Some preliminary results of experiments are presented.

Jan 1, 1967