Search Documents

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

n the early days of the Hauraki goldfield (1866 to 1889) almost the only system of ore treatment was wet crushing followed by copper plate amalgamation. A further saving of bullion was in most cases obtained from the tailings by means of pans or berdans. Though this system was not always as efficient as might have been desired it answered fairly well for the bulk of the gold-bearing quartz of the Thames and Coromandel districts, where the gold occurs chiefly in the form of visible particles, and there is not a great deal of silver. It failed, however, with most of the ore found in the Upper Thames or Ohinemuri district, especially in the Karangahake and Waihi portions of the field. In those days the cyanide process was not, and the usual prescription of the mining " expert" was smelting. At Karangahake, many attempts were made to discover a payable method of treatment for the so-called" refractory" ore, but on thewhole with very 'little success, and the district struggled along for a number of years without adding very materially to the production of gold in New Zealand. At Waihi, the Martha Co.'s stamp battery treated by wet crushing and copper plate amalgamation some 18,000 tons from the Martha Reef, worth probablyat least £4 per ton, but the average return was considerably less than £1 per ton, a sum which barely paid working, expenses, and consequently the shareholders were glad...

Jan 1, 1903

By R. D. Berkenkotter

Titanium and iron assays obtained from cores of three diamond-drill holes from the Cebolla Creek titaniferous iron deposit were evaluated by statistical techniques to obtain information concerning the mineral characteristics of the deposit and to make a preliminary determination of sampling requirements for the deposit. A range of sample volumes representing sizes from one-sixth NX core 2 feet in length through full NX core 10 feet in length were prepared by split-ting the NX core with a diamond saw and combining pulverized splits. Results indicate the existence of at least two statistical populations having different average grades of iron and titanium. Each has an assay frequency distribution that is not normal but is highly peaked (leptokurtic). Frequency distributions of assays from specific altered zones of the drill holes appear to be normally distributed. Increasing the cross-sectional area of the sample unit to change assay volume did not result in significant changes either in assay values or the resulting frequency distributions of assays. However, when assay volume is increased by increasing sample interval, the shape of the assay frequency distribution changes, and a normal distribution of assays is approached. Positive correlation exists between titanium and iron assays. The degree of correlation, although very significant, is too low to use for prediction purposes. Although the amount of data from three widely separated drill holes is not sufficient to establish an average grade for this large deposit, it indicates a range of expected assay values and provides some information for determining requirements of future sampling for evaluation purposes.

Jan 1, 1963

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By Dale Ramsey

During Phase IV of our Landfill Mine Stabilization project at a coal burning power generating station, it was determined that a coal barrier pillar separating two abandoned areas of the deep mine had to be breached prior to expansion of the ash disposal area. The proposed plan by the landfill design engineers involved using a high pressure jet cutting tool to cut a slot to allow water flow to an existing industrial waste water treatment facility. Our plan proposed using explosives to breach the pillar from the surface reducing earth disturbance in a high quality watershed while reducing the project cost and accelerating the project time schedule. Many issues surfaced with the proposed change of using explosives. There were a number of lessons learned from this case history and is the primary basis of this paper.

Jan 1, 2003

By Marilia S. de Magalhaes

Keywords: sinter, characterization, agglomeration, iron ore Iron ore sinters are the main burden of blast furnaces for pig iron production. The evaluation of these agglomerates is very important due to their properties affect indirectly the productivity and costs of production of the steel industry. In the sintering plants, the standard procedure of sinter assessment has been carried out by particle size control, bulk chemical analyses, tumbler and/or shatter tests and determination of reduction degradation and reducibility indexes. Microscopy techniques have just been applied to characterize sinters produced in pilot conditions, however, these techniques, the classical ones and the less traditional, allow enhancing the industrial sintering process assessment. For investigation of the phases, microstructures and fabric, reflected-light and scanning electron microscopy(backscattered electrons images) were used; for micro analytical chemical examination, energy-dispersive X-ray spectrometry; for Kikuchi patterns registers, electron backscattering diffraction. In addition to the microscopy techniques, the magnetic behavior was depicted by means of magnetic susceptibility measurements. Iron ore sinters are made up by hematite, magnetite, silicoferrite of calcium and aluminium and silicates. These phases develop either during sintering or, in some proportion, represent remnants of ores and fluxes; this is the case of some hematite and Mg-bearing silicate, respectively. From the magnetic susceptibility results, three different behaviors were determined, which are directly related to the magnetiteproportion in the samples. The phase association and proportion, the sintering conditions andthe quality assessment are some features appraised by such procedures, which reveal themagnitude of this proposal in sintering plants.

Jan 1, 2005

By William R. Barton

COLUMBIUM (niobium) and tantalum are similar refractory metals with closely related properties and uses and close association in ore deposits. Until recently both metals, particularly columbium, were essentially laboratory curiosities. However, since the beginning of World War II, applied technology, under the impetus of national security requirements, has realized many chemical, electronic, nucleonic, and missile and rocketry applications, where high temperature or corrosive environments require the use of columbium or tantalum. At the same time, advances in these fields have resulted in intensive research on the geological distribution, resources, metallurgy, and properties of these two metals; their alloys and compounds; and the development of a full-fledged columbium-tantalum industry. The future appears to promise continued acceleration in such studies and ever-increasing demand for these elements. The raw material supplies of columbium are abundant, and the extractive metallurgy of columbium is well enough advanced to assure adequate supplies of the element at reasonable prices to meet any projected demands. Although the extractive metallurgy of tantalum is similarly well developed, raw material supplies are so limited that, lacking new ore discoveries, an increase in demand to five times the 1959 level would severely tax ore-production facilities. Approximately 120 tons of tantalum and about one-half as much columbium was produced in 1959. Additional quantities are consumed as compounds or additive alloys such as ferrocolumbium and ferrotantalum columbium (55).3

Jan 1, 1962

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By R F. G Phelps, C J. S Sangster, G S. C

Narrow vein metalliferous mining in the UK has a long history, but there are only two small gold operations at present (Clogau and Gwynfynydd). Four further gold properties are at various stages of evaluation (Calliachar, Cononish, Curraghinalt and Maestryfer). The South Crofty tin mine closed earlier in the year. Narrow veins are exploited underground and are challenging to evaluate because of their geologically variable nature. They are generally less than 3 m wide, discordant, of variable dip (

Jan 1, 1998

By Charles Stone, Madan Naik, Drupad Desai, Karel Rossler

Planning of New York’s new subway line dictated the location of shallow underground station caverns and track crossovers. Clear span openings ranging from70 feet to 100 feet and lengths in excess of 1000 feet, coupled with low rock cover ranging from 25 feet to 40 feet required judicious selection of construction methods, equipment, and proper sequencing of the excavation stages. Rock classifications alone could not predict the behavior of the rock mass during construction. A robust design procedure that considered most of the important aspects of rock behavior and elements of shallow tunnel design, minimized the negative impacts of variable geotechnical data. This paper describes the intricacies of the planning and design of the $16 billion Second Avenue Subway with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2005

By C. Deutsch

Resource estimation for the West Leeville deposit is prepared using a conventional explicit approach. The geologic model is developed using interpretive methods based on visual logging. Grade shells are then prepared at low and high grade cutoffs. The low grade shell includes material of interest (Au > 0.010opt), while the high grade shell is developed slightly below the economic cutoff grade for mining. Grade estimates are made within these boundaries. This paper documents a conditional simulation study to evaluate the uncertainty contributed by both the grade shells and grade estimates. Multiple realizations are generated for the grade shells and the grades. The full combinatorial of realizations are merged to assess the uncertainty and the relative contribution of the grade shell and grades.

Jan 1, 2007

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

By J. Kretschmann

Around the world, mining has been done for thousands of years for the benefit of humankind. The winning process in mining operations ends with the depletion of the deposit or its closure if the operation becomes economically unprofitable. After that, a period of post-mining follows which may last for a very long time and which is generally regarded as a period of hazards, risk and high cost. In the USA alone, approximately 500,000 abandoned mines do exist; worldwide, there are millions. In Germany, too, we have had to deal with abandoned mines for a considerable period of time now.

Jan 1, 2012

By Daniel H. Israel

Indian tribes own a substantial portion of the West's minerals. More importantly, Indian reservations contain coal, oil and gas, uranium, and oil shale reserves in unusually large and unencumbered blocks. Many tribes are now prepared to intensify development of their large reserves knowing that they can offer energy partners the unique opportunity to develop major energy facilities free of overlapping local, state, and federal permitting authorities. The tribes, therefore, can offer mineral developers both substantial reserves and an unusual degree of freedom from a multiplicity of government regulation. In the past, Indians and energy companies enjoyed only partial success as business partners. Indian tribes lacked the resources and know-how to act as equal partners with large oil and gas and mining operators. The tribes relied on the Bureau of Indian Affairs (BIA) to initiate and execute reservation energy projects, and as a result the tribes never developed adequate tribal structures and the expertise to responsibly manage their energy resources. At the same time industry made little effort to understand and learn the laws, customs, and institutions existing on Indian reservations. To the contrary, industry found it easier to bypass the tribes and deal with BIA officials. But the situation has changed. In 1975 the tribes organized an effective coalition, the Council of Energy Resources Tribes (CERT), which recently acquired substantial federal assistance to bring the tribes a level of technical and business expertise that begins to equal that of industry. Because the tribes have changed the rules of the game, industry must now change and learn to work directly with tribal governments. A working knowledge of Indian law, practices, customs, and policies must be acquired by energy companies before beginning negotiations with tribal governments for development of reservation energy resources.

Jan 6, 1980

A general outline of the significant features in the quality and manufacture of the more common refractories is given. Where possible, linkage between quality development and control and service applicationhas been shown and explained. INTRODUCTIONThe refractory industry is no stranger to change. New processes and revision of old processes in other industries are the harbinger of new and revised products in refractories.Few of the changes are dramatic; generally they are evolutionary rather than revolutionary. New developments are additional to, and inclusive of, established practice.Therefore in this paper it is necessary to repeat much of what is already known in order to show the development taking place.FIRECLAY REFRACTORIESGeneral technology Fireclay refractories are the most common, the most varied and the most versatile of all refractories. Virtually any composition of silica and alumina up to the composition of kaolin is possible. For purposes of comparison they may be classified in the Continental fashion in accordance with chemical composition or in the American way according to "duty". That the two methods are equivalent is shown by an inspection of the alumina-silica diagram of Bbwen and Greig (1924). 'Fireclay refractories are composed of a glassy and a crystalline component derived from the chemical and physical nature of the raw materials used in their manufacture.

Jan 1, 1961

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996

By Ádria Rocha Corrêa

Durante a solidificação de ligas metálicas, o produto fundido se contrai, o qual provoca o surgimento de espaçamentos vazios na interface metal/molde chamados de “gaps”. Estes gaps causam o aumento da resistência térmica influenciando em toda a cinética da solidificação. A transferência de calor durante a solidificação depende do conhecido parâmetro chamado de coeficiente global de transferência de calor ( hg). Este parâmetro é representado pela equação do tipo: hg =C.t-n, a qual indica que a eficiência térmica na interface metal/molde decai com o tempo. Muitos parâmetros podem influenciar o coeficiente global de transferência de calor (hg), neste estudo, os percentuais de Sn em ligas do sistema Al-Sn são analisados (10,20,30 e 40%Sn). Portanto, o principal objetivo deste estudo é propor uma relação matemática que descreva, para o sistema Al-Sn, a evolução hg em função do teor de Sn. A relação matemática foi obtida através do método dos mínimos quadrados

Aug 17, 2017