Search Documents

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

Retreating Cu-Mo Rougher Tailing by Flotation for Concentration of Copper and Molybdenum

Sep 13, 2010

Appropriate roof control is the most important requirement in underground coal mining and, in the case of longwall panels or second mining in room and pillar extractions, this can be simply expressed in terms of good and predictable roof caveability. Studies of roof caveability have been undertaken in many coalfields around the world. Most of their conclusions. however, are directly related to the mining and geological conditions experienced in these areas and as a result, may not be applicable to the conditions encountered in the Appalachian coalfield. Furthermore, some of these studies appear to be theoretical and conceptual, ignoring many important parameters of the geological environment, whereas others rely heavily on geological information but lack a rigorous foundations upon which quantitative design guidelines can be built. The objective of this study is to analyze caving and mass deformation characteristics above longwall panels in Appalachia and includes: - Analysis of the effects of the geological and geomechanical characteristics of the strata on the caving height and the bulking of the caved-material. - Testing of the applicability of the various theoretical and empirical models of roof caving. Formulation of a numerical around- deformation model for ion-elastic material behavior.

Jan 1, 1986

By E. C. Lane

[This is the tenth in a series of retorts on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee e end the Bureau of Mines of the United States Department of the Interior. The first report rave data on motor gasolines sold during .e winter of 1935-36.3/ The present report presents analytical data for 1,732 samples, representing the products of approximately 50 companies, which, as in previous surveys, include both lame and stall suppliers. In addition, the Pacific coast is represented by data that were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. he number of samples, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as follows: Regular price, 934 samples, 230 items, and 50 brands; premium price, 465 saris samples, 184 items, 40 brands; third-grade gasolines, 360 samples, 177 items, and of these terms as used in the surveys are follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.]

Jan 1, 1941

By Reeves M

A review of the literature available in English on kriging and geostatistics is given with the references cross-classified by their subject matter for convenience and ease of use.

Jan 1, 1979

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

Industrial Minerals production in New Zealand is limited in both quantity and range, but imported in quantities that make New Zealand the world's biggest consumer per head of population. The use of industrial minerals is assured as both population and standard of living increase regularly. But to develop these minerals in the New Zealand environment requires the mineral, or its market (both local and export), to have characteristics that negate the remote geographical location. Volume and/or uniqueness can achieve this.

Jan 1, 1997

A good deal of experimental work has been done from time to time on the application of compressed air to the elevation of wet pulp. On account of the flat nature of most of our mill sites elevation of the pulp has to be provided for, and the various methods in vogue show considerable loss of time, in the replaceing of wearing parts. During the last two years the writer has carried out a great many experiments with a view of devising an elevator that will give continuous work with a minimum of wear.The results do not show a high efficiency for the power employed, but the lift is continuous in operation, very cheaply installed, and possesses no wearing parts. The lift was tried working in a bore hole of 8 in. diameter, but in many cases it is more convenient to sink a small well for the purpose. The result to date showed that the most efficiency was obtained when the depth of the wellwas not less than the height of the lift required. The pressure of air required in pounds per square inch was (approximately) half the number of feet to be lifted.In the majority of cases the lift required varied between 20 ft. and 50 ft. and the air pressure required between 10 lbs. and 25 lhs. per square inch. In most existing installations the air compressors in use were delivering air to the receivers at about four times that pressure, and when air so compressed was expanded to perform its work at a reduced pressure, it was apparent that the power exerted in origInally compressing the air above the working pressure required at the lift was absolutely lost.

Jan 1, 1901

By Gordon King

The site of the First Quality Tissue plant is located on a previous paper production facility in Lock Haven, Pennsylvania. The new development, which included the construction of a tissue machine building, baled building, converting building, various storage buildings and an electrical switchgear building, required the use of deep foundation systems to transfer loads below compressible fill and alluvial soils. Loading details provided by Jacobs Engineering, the project structural engineer, detailed braced steel frame buildings with typical column loads ranging from 75 to 150 kips and slab live loads of 250 to 300 psf. As an exception to this, however, the tissue machine and stock preparation building, which had a roof height ranging up to 85 feet, had column loads ranging up to 800 kips in addition to high dynamic loads. The First Tissue plant is located in a river valley in the hills of Western Pennsylvania. To evaluate the proposed site conditions and to formulate recommendations for the structure foundations, a geotechnical study was performed by the owner. Approximately 30 borings were advanced to bedrock, with wire-line coring performed in the tissue machine building. The borings disclosed a soil profile comprising of the following:

Jan 1, 2004

By J. Dienenthal

Automatic Charging and Stoking Machines for use at ferroalloy furnaces are in operation for more than 20years. Dango & Dienenthal Maschinenbau GmbH (short: DDS) has developed several machine generations. Today advanced solutions help to achieve better charging and stoking results to minimize cost and to improve the working environment around the furnaces. Three different alternatives can be considered: Rail-mounted solution The machine(s) travel(s) on an overhead monorail to one or several furnaces and is locked in the desired working position from where charging and stoking is performed. Mobile solution This machine travels on the charging platform and is also locked at the respective working position to perform charging and stoking. Automation of a standard mobile charging and stoking machine A standard charging and stoking machine can be adapted for automation. A reliable navigation system is included. Charging and stoking is performed with the moving machine. Advantage versus other solutions: considerable lower investment cost and possibility to upgrade the mobile charging and stoking machine for later automation. Overall, automatic charging and stoking can save up to 10 per cent of the specific smelting energy. A better and more consistent furnace operation can be achieved. Different programs are used to cope with different furnace conditions and changing raw materials. All machine movements can be recorded and correlated to other furnace parameters. Working environment on the charging platform is greatly improved.

Jan 1, 2007

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By Steve Kral

Reducing the cost per ton and increasing productivity are key factors in a mine’s profitability. Mining companies can do little about commodity prices. So to keep a mine operating at a profit, management must reduce costs and improve worker and equipment productivity in every facet of a mining operation. From mining to crushing to processing, mine management is constantly seeking new methods and technologies to improve the way it mines minerals. And it is willing to borrow techniques used by other operators.

Jan 1, 2002

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed.The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences. These were...

Jan 1, 1970

By Hamid Maleki

A geotechnical monitoring program has been implemented at Energy West Mining Company for enhancing site-specific evaluation of longwall stress conditions. This program consists of underground measurements at five locations in two neighboring mining districts located in the Hiawatha and Blind Canyon Coal Seams under moderate to deep cover. Within the last five years, additional measurements, including data on recorded seismic events and face conditions, have been incorporated into the data collection program together with detailed geologic mapping of longwall gateroads. In conjunction with the measurement program, the authors have completed detailed boundary-element stress analyses of the mine plans. Models have been calibrated using the data from in-mine instrumentations and then routinely used for evaluation of mine plans at depths approaching 2,600-ft. The work has improved our understanding of load transfer, seismicity and yield pillar performance. It has identified areas of potential increased stress levels at certain longwall face positions and provided guidance to measures that could be considered to mitigate the potential for these increased stress levels.

Jan 1, 2009

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996

By Gift Chisakuta, Bravo Mbao, Nils Schwarz, Angus Feather, Anthony Mukutuma

Bwana Mkubwa is a 50 000 tons per annum copper cathode producer, owned by First Quantum Minerals and located in Ndola, on the Zambian Copperbelt. The Bwana Mkubwa solvent-extraction circuit was started up in 1997. In 2002, the plant began treating ore from First Quantum?s Lonshi mine located in the Democratic Republic of Congo. The Lonshi ore is exceptionally fine and the amount of solids in the feed solution reporting to the solvent-extraction feed solution increased dramatically. Initially, crud was filtered in a filter press, but this rapidly blinded and seldom produced anything better than a wet sludge containing large quantities of organic. In December 2003 the decision was made to install a Flottweg Z4E-3/441 Tricanter® centrifuge to recover organic from the crud. The installation was completed in June 2004 and has since led to significant improvements in plant operability and savings in organic consumption.

Jan 1, 2007

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992