Search Documents

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By A. Roca, G. Ríos, I. Ruíz, M. Cruells

Flash Smelting Furnace (FSF) hot dust-laden is cooled in a waste heat boiler (WHB) and then dedusted in electrostatic precipitators (ESP’s) before being treated, together with the Peirce Smith Converters off-gases, in the sulfuric acid plants for SO2 removal. FSF dust is sulfated by SO2 and O2 in the WHB. Typically, 70% of the dust from the FSF drops in the WHB while the remainder is caught in the ESPs. The collected dust is recycled to the FSF for Cu recovery. Some smelters have developed hydrometallurgical treatments to recover Cu from the dust; impurities, such as As and Bi, are bled as leach plant residues. This paper presents a study (laboratory scale), of leaching the FSF dust, generated in Atlantic Copper Smelter using the weak acid bleed from the gas scrubbing/cooling section (GSCS) of sulfuric acid plants. Leaching was performed with 0.5 mol L-1 sulfuric acid concentration, 60ºC, and a solid/liquid ratio 1/3. After leaching, H2O2 was used for arsenic and iron oxidation. pH was adjusted for precipitation of arsenic and iron as scorodite or as scorodite and arsenical jarosite. The precipitation was carried out at 95ºC during 3-6 h. Liquids after precipitation are suitable for subsequent treatments of electrolysis. INTRODUCTION The copper smelter dusts are usually recirculated totally or partially to the flash furnace. This practice increases the amount of impurities feeding the furnace. Some authors have developed processes for treatment of these materials for copper and zinc recovery and for arsenic, antimony and bismuth inertization. The processes for the treatment of copper smelter dusts can be pyrometallurgical (Yu, 1987; Carter, Vance, Aldridge, Zaw, & Khoe, 1994; Fu, Jiang &Wang, 2000), hydrometallurgical, or mixed processes (Yin et al, 1992; Mulale, Mwema, & Mashala, 1999; Gorai, Jana, & Khan, 2002). Hydrometallurgical processes have been extensively studied and, in some cases, applied to an industrial scale. The most important chemical reagent proposed for leaching the dusts has been sulfuric acid (Roman-Moguel, Plascencia, Pérez, & Garcia, 1995; Gabb, & Evans, 1997; Larouche, 2001; Morales, Cruells, Roca, & Bergó, 2010; Cáceres, Cruells, Morales, & Roca, 2012; Ecometales, 2013; Yang, Fu, Liu, Chen, & Zhang, 2017). Processes developed in alkaline media, and in some cases with the presence of sulfide, have also been carried out (Gabler, & Jones, 1988; Morales, Hevia, & Cifuentes, 2009; Alguacil, Garcia-Diaz, Lopez, Rodriguez, & Alonso, 2013), as well as by using a bioleaching process (Massinaie, Oliazadeh, & Seyed Bagheri, 2006; Bakhtiari, Atashi, Zivdar, Seyedbagheri, & Fazaelipoor, 2011).

Jan 1, 2019

By Robert McClure

The detection, recovery and disposal of commercial explosives and explosive waste has always carried a level of risk and requires specialized equipment and technical expertise. Improperly stored, discarded, deteriorated, misfired, stolen or surplus products are often the primary sources of explosives that require safe disposal. Detection and disposal tools available today have advanced significantly due to developments in Counter-Improvised Explosive Devices (C-IED) operations and commercial blasting technology. These technologies have provided safer more efficient ways to detect, investigate and dispose of commercial explosives products in order to minimize property damage and potential harm to disposal personnel and the general public.

Jan 1, 2015

By A. Baldwin

Reports technical progress in designing four machines to be used in mining coal underground, applying innovative concepts at the design stage (instead of add-ons). A study phase was followed by design activity, including calculations supporting the designs. Scale models of three machines were built, and a full-scale mock-up of the conventional loader was used to measure human factors parameters.

Jan 1, 1976

By Jae R. Lee

Keywords: Self-propagating high temperature synthesis, AlN, Powder synthesis The particle size and shape effects of starting raw powders on the synthesis of aluminum nitride by self-propagating high temperature technique under high nitrogen pressure were investigated with various AlN diluents and Al reactants. It was found that the structure of beds of the starting raw particles largely affected the pore channels for nitrogen gas infiltration as well as the passages for combustion propagation before and during the reaction, resulting in the morphology and purity changes of the synthesized products. The AlN product of purity over 98% with about 30 microns was obtained.

Jan 1, 2005

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By M. K. Mohanty, H. Akbari, L. A. Ackah

Dry separation was the predominant method of coal cleaning in the United States from the 1930s to 1980s. The application peak of dry separators for cleaning raw coal was in 1965, when about 23.1 Mt of cleaned bituminous coal was produced. The main advantage of dry coal cleaning is the elimination RIWKH GHZDWHULQJ VWDJHV DQG VLJQL¿FDQWO\ UHGXFHG moisture in comparison to wet processing. In addition, developed dust control systems have made dry cleaning method an environmentally friendly process. The largest air-based coal cleaning plant was built in Pennsylvania in 1968 and could clean 1,272 t/h of raw coal sized smaller than 19 mm. This was followed by a decline in dry coal cleaning to less than 3.6 Mt in 1988. Some of the main reasons that shifted coal operations IURPGU\WRZHWSURFHVVLQJZHUHWKHQHHGIRUPRUHHI¿FLHQW separations with lower density cuts, increase in raw coal surIDFHPRLVWXUHVSHFL¿FDOO\LQXQGHUJURXQGPLQLQJWRFRQWURO GXVW ¿QHUSDUWLFOHVL]HUHTXLUHPHQWV LQFUHDVHLQ¿QHVLQUDZ coal from underground mines, and health and safety concerns related to dust and noise (Arnold, Hervol and Leonard III, 1991; Miller, 2011).

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By Michael D. Balen

During the years 1987 through 1989, the Bureau of Mines Alaska Field Operations Center (Bureau) in cooperation with the Western Field Operations Center and the Alaska Division of Geological and Geophysical Surveys (ADGGS), conducted mining, geological, and geochemical investigations in the 5.7 million-acre Valdez Creek Mining District (VCMD). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district studies program. The Bureau's MLA program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies. The information also provides the basis for decisions that would expand the domestic supply of important mineral resources, primarily strategic and critical minerals. Much of the MLA work is done jointly with cooperating State or U.S. geological surveys.

Jan 1, 1992

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

The United States Bureau of Mines frequently receives requests for information regarding the details of its organization and the nature of its activities. In response to such an inquiry a series of articles outlining the work of the bureau as a whole and of its different divisions was prepared and published in the United States Daily, Washington, D. C., during November, 1929. These articles are reprinted here in the hone that they may assist in giving the public a more complete understanding of the aims and purposes of the bureau and the methods by which it is laboring for the attainment of safer conditions and more efficient methods in American mineral industries. An index of these articles, with the dates of 'their publication in the United States Daily, is given below.

Jan 1, 1930

By T. T. Tomimatsu

[This Bureau of Mines paper investigates explores, and analyses the Corporate structure dynamics and Rancid role to evaluate the economic health of the U.S. copper producers. It highlights the Corporate policy options and measures of corporate profitability and suggests that a competitive domestic copper industry will exist in the future. The study highlights the activities of 14 selected major copper-producing companies, including their subsidiaries o affiliates, that were responsible for more than 95 percent of the total U.S. production in each of the years since 1969. The selected firms are hot all primarily in the business of producing copper. Several of the large producers are classified by the financial institutions as integrated oil and gas enterprises.]

Jan 1, 1980

Undisturbed minor sedimentary structures-cross-bedding, ripplemarking, scour-and-fill, slumping-are present in most of the rock types in the Willyama Series of the Broken Hill district and in the orebodies.This indicates that there has not been any significant movement of mineral matter within or into the rocks during or after metamorphism, that the rocks have not flowed during tectonic deformation or during metamorphism, and that the ore is an original sedimentary deposit in its sedimentary position.Sedimentary processes, depositional and mechanical, are indicated to explain the deposition of sedimentary metallic minerals and their concentration into large masses. The Broken Hill orebodies show evidence of these processes.INTRODUCTIONI visited Broken Hill for one week in May, 1958, at the invitation of Mr. Haddon F. King, Director of Consolidated Zinc Pty. Ltd. He asked me to examine the rocks and orebodies in the mines and outcrops at Broken Hill for:1. Sedimentary structures that might be used to determine the facing of the banding;2. Indications of the original nature of the rocks if I considered they may have been sedimentary; and3. Indications of any possible sedimentary origin for the ores.It has been stated (Gustafson et al., 1952, p. 30) that there was no indication, in the banding, of the facing of the banding, but recently B. P. Thomson had found examples of what he had interpreted as graded bedding (personal...

Jan 1, 1959

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, Hara, A. S. Kabir, R. Petrov

Manufacturing of thin sheet is difficult in industries. Some approaches, such as small-draft multi-pass rolling, intermediate annealing, isothermal rolling and high-speed rolling were proposed to overcome the deformability. In this study, different rolling speeds from 15 to 1000 m/min were employed to twin rolled cast AZ31B magnesium alloy to different reductions. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2014

By Youngtak Ko, Wonnyon Kim

Korean contract Mn-nodule field in the NE equatorial Pacific is composed of seven sectors showing average water depths of 4,513 - 5,025 m. Of the various factors controlling the property of Mn-nodules, water depth has a potential linkage to chemical composition, shape and abundance of nodules. To clarify such a possibility, we review more than 20 years of research data in one of the northern sectors (hereafter KR1) where there is a marked contrast in water depth. High-resolution seabed mapping clearly separates a northern part from a deeper southern part, cutting across the middle of the KR1. In terms of nodule occurrence, manganese nodules in the deeper north are comparatively larger (2-4 cm) with rough surface (t-type) and discoidal shape (D-type), while those in the south are generally small (<2 cm) with smooth surface (s-type) and irregular shape (Itype). In addition, the nodules in the north have higher metal contents including Cu, Mn and Ni. Such connections of water depths to nodule occurrence and metal contents are commonly observed in the Korea licensed Pacific nodule fields. However, the relation between nodule abundance, size and water depth may be a different story. In KR1, nodule abundance and size are probably controlled by morphological features especially in the north. Seamounts in the north continuously provide rock fragments as new nuclei for the nodules. As a result, the nodules can not grow larger than 2 cm and show the shapes of newly formed nodules (i.e., smooth surface and irregular shapes). Such an interpretation is supported by anomalously high backscattered intensities in the side-scan sonar image map of the north, which possibly reflects a younger generation of magmatic activity.

Sep 1, 2014

"In mining operations, it is widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In this paper, an integrated solution framework for reducing process variability, increasing process efficiencies and maximizing plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis “gap” evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.INTRODUCTION The changing landscape of gold mining and processing presents many challenges that threaten sustainability of existing (marginal) operations as well as deter investment in new projects. As existing “shallow” ore resources become depleted, mining operations are increasingly treating low-grade ores with complex and randomly variable mineralogical characteristics. For example, in South Africa, historically one of the major gold producers, the average grade of ore treated has been decreasing from averages above 4.5 – 5 g/t to current grades averaging less than 3 g/t within a decade (Chamber of Mines, 2012). Moreover, lower tonnages are being treated as a result of the narrowing of the available resource base. Also, the regulatory framework has tightened over the years due to heightened concerns on the safety, health and environmental impacts of mining and related activities."

Jan 1, 2014

By Armin W. Stuedlein, Youssef Bougataya

Early stage design of driven piles primarily relies on static analysis based on one or a combination of total and effective stress approaches, the latter known as the method to estimate axial capacity. A database of 85 piles driven in the Puget Sound Lowland region and monitored at End of Driving (EOD) and Beginning of Restrike (BOR) was compiled along with capacities estimated using the CAPWAP procedure. Established soil profiles based on borings with standard penetration tests (SPT), cone penetration tests, and geologic maps were matched with their corresponding unit shaft resistance profiles from the CAPWAP procedure and resulted in more than 1,200 observations. In this study, eight new models were developed to predict the coefficients at EOD and BOR, based on the corresponding USCS categorization. Each coefficient model is formulated using a three-parameter exponential function, calibrated to capture the profile of coefficients with depth. These models could benefit the designer by providing them with a simple, empirical model that accounts for soil type and setup in a smooth, continuous function with depth. A parallel analysis was performed to assess the accuracy and variability of the formulated prediction models to facilitate implementation in load and resistance factor design (LRFD). INTRODUCTION The design of the axial capacity of driven piles during the planning stages of a project is typically based on a static analysis approach. The goals of this approach are to predict the components of capacity, consisting of the shaft and toe bearing resistances, and to assess project concept feasibility and preliminary lengths. In most cases, this analysis is based on empirically-developed methods, such as the total stress method, also known as the method (Tomlinson 1987) or the effective stress method known as the method (Esrig and Kirby 1979; Fellenius 1991). Many other methods, such as those based on in-situ test results exist and rely on correlations of blow counts from the standard penetration test (SPT), and cone tip and sleeve friction resistance from the cone penetration test (CPT), to shaft and toe pile resistances (Schmertmann 1978; Meyerhof 1976; Nottingham and Schmertmann 1975; Nordlund 1963; Eslami and Fellenius, 1997; De Ruiter and Beringen 1979). Although these methods were generally developed using data from specific geological regions, they are often recommended in national design manuals (e.g., FHWA, Hannigan et al. 2006).

Jan 1, 2018

By R. Altindag

Engineers and researchers need to estimate the mechanical properties of rocks from P-wave velocity. In previous studies, the researchers have investigated either the limited values or all the data belonging to sedimentary, igneous, and metamorphic rocks together in the same statistical analysis. In this study, the raw data pertaining to only sedimentary rocks was taken from previous studies and evaluated. For this purpose, a total of 97 samples of sedimentary rock types were subjected to statistical analysis. First, the relationships between P-wave velocity and physical-mechanical properties were investigated by simple regression analysis. All the data were then subjected to multi-regression analysis. Some empirical equations with high correlation coefficients were derived for rock engineers. The equations obtained from the analyses are compared with previous equations found in literature.

Jan 1, 2012