Search Documents

By A. Arenas-Flores, Pandiyan Thangarasu, J. P. Hernández-Lara, F. R. Barrientos-Hernández, J. A. Romero-Serrano, A. Hernández-Ramírez, M. Pérez-Labra

BaTiO3 doped with Gd3+, was synthesized from BaCO3, TiO2, and Gd2O3 as powders using the solid state reaction method (Ba1-xGdxTi1-x/4O3). The milling of the precursors was performed in an agate mortar with acetone as control means and compositions x = 0.001, 0.005, 0.05, 0.15, 0.25, 0.35 Gd3+ (wt%). Firstly, the powder mixture was decarbonated at 900 °C for 8 h, after it was sintered at 1400 °C for 5 h. Tetragonality of synthesized BaTiO3 doped with Gd3+ was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectroscopy (RS). Subsequently, the powders sintered were uniaxially compacted cold until to obtain pellets of about 10 mm in diameter; which again were sintered at 1400 °C for 4 h. XRD patterns and Raman spectra results revealed that the crystal phase of the obtained particles was predominately tetragonal BaTiO3.

Mar 1, 2017

By Chaoying Ni, Dimitry Sediako, Prashant Karandikar, Sean Fudger

Neutron diffraction measurements were performed on steel encapsulated metal matrix composites (MMCs) in order to quantify bulk residual stresses. A coefficient of thermal expansion (CTE) mismatch induced residual compressive stress method is utilized as a means of improving the ductility of the MMCs and overall efficiency of several macro hybridized materials systems. Systems consisting of an A36, 304 stainless steel, or Nitronic® 50 stainless steel shell filled with an Al-SiC or Al-Al2O3 metal matrix composite are evaluated in this work. Upon cooling from processing temperatures residual strains are generated due to a CTE mismatch between each of the phases: steel, aluminum, and reinforcement. The analysis shows variation in the measured strain and stress results due to outer steel thickness, difference in CTE between materials, and relative position within the composite.

Mar 1, 2017

By Maria Rashidi, Maryam Ghodrat, Bijan Samali

Treatment of sharp medical waste (waste disposable syringes) produced in hospitals or health care facilities in an environmentally sound ways have raised concerns relating to public health and occupational safety. Life cycle assessment (LCA) is a decision-supporting tool in waste management practice; but relatively little research has been done on the evaluation of sharp medical waste treatment from a life cycle perspective. Our study assesses the environmental performances of medical waste incineration as a type of dominant technology for specific medical waste of average composition. Inventory models were used for waste incineration and residues land fill. Background data were derived from modelling performed in HSC Chemistry thermochemical package linked with GaBi environmental assessment tool. Two scenarios have been considered and compared: Waste disposable syringes partially replacing coke in Electric Arc Furnace (EAF) steelmaking (WSI) and conventional incineration with pure metallurgical coke without adding waste syringes (CI). The results of this study could support the medical waste hierarchy and indicate that from a life cycle perspective, replacing part of metallurgical coke with waste syringes in electric arc furnace steelmaking leads to fairly significant reduce in most of environmental impact categories.

Mar 1, 2017

By E. Salinas Rodríguez, I. Rivera Landero, E. G. Palacios Beas, J. Hernández Ávila, E. Cerecedo Sáenz, M. A. Mesinas Romero, M. I. Reyes Valderrama

For this study, a sample of 5 g of copper powders obtained by grinding printed circuit boards of computers fixe to 50 mesh (270 μm) according Tyler® series was used. This sample was wholly characterized by XRD, SEM–EDS and AAS. The leaching medium used wasO2S2O3 2. From the evaluated variables it was obtained an apparent order of the reaction of n = 2.34 s−1, whereas according the effect of partial oxygen pressure it was obtained an apparent order of reaction of n = 0.9516 and the activation energy of system was of 6.5 kJ mol−1, the results so achieved suggest a transport control to the solid–liquid interface. Under certain work conditions such as: S2O3 2 ¼ 0:5M, 500 mL, 750 min−1, P/PO2 = 1 atm, 338 K, 5 g of sample and 9000 s of reaction time, it is possible get up to 97.35% of leached copper.

Mar 1, 2017

By M. Firdaus, M. A. H. Shuva, M. A. Rhamdhani, G. A. Brooks, S. Masood, M. A. Reuter

Declining grade of primary ores and resource efficiency have led us to process more alternative metal resources such as e-waste. One of the processing routes for extracting valuable metals from e-waste is through the black copper smelting. However, the underlying knowledge of the thermodynamics behaviour of the valuable metals contained in e-waste during smelting are limited which prevent us from developing an optimised process to recover all the metals. These different metals clearly will have different favourable conditions for their extraction. To illustrate this, the distribution behaviour of germanium (Ge) and palladium (Pd) between liquid copper and ferrous-calcium-silicate slag during black copper smelting was analysed. It was demonstrated that oxygen partial pressure and slag composition affect the partitioning of these metals to the copper phase and the favourable slag chemistry for recovering these metals is opposing. Considering the available thermodynamic data of these metals, an analysis for the optimum conditions is presented.

Mar 1, 2017

By L. I. C. Fernandez, E. B. Ferreira Filho, L. G. Pedroti, L. G. Justino, W. E. H. Fernandes, R. C. S. S. Alvarenga

More and more industries have been concerned with the disposal of the wastes generated in their production processes, once this generates a positive impact, both visual and economic enterprise, no more needing to have resources for transport and final disposal of wastes. In this context, and seen the importance of the Portland cement a sa building material, which aims the creation of an ecological cement from the mix of two wastes, the grits, which is a waste generated in pulp production, and the granite beneficiation waste. It proceeded initially with the chemical and physical descriptions of the wastes. Five mixtures, varying the percentages of the wastes and the preparation method of the raw materials, were prepared. After,the blends were sintered in a muffle furnace at 1300 °C for 15 min, forming new compounds that were compared with national cements, according to the Brazilian technical standards. It was concluded that the sintering of the product obtained satisfactory results, presenting good binder characteristics, however, some parameters were outside the limits for common Portland cements such as rapid setting time, large expandability and low compressive strength.

Mar 1, 2017

By P. R. Taylor, B. N. Carlson

Rare earth magnets play an increasingly important role in high end technology, and the manufacture of rare earth magnets, such as the NdFeB type, consume a large amount of the rare earths produced. Recycling of this material could provide an important domestic source for these materials. A selective sulfation roast has been proposed; the central principle of which is to take advantage of the differing stabilities of the rare earth sulfates as compared to those of iron under an air/SO2 atmosphere. Experiments show iron is found to be stable as an oxide, however, neodymium is found to form an oxy-sulfate phase.

Mar 1, 2017

By A. Lanterne, J. A. Bones, E. Øvrelid, Y. Hu, M. Di Sabatino, F. W. Thorsen

This study presents a new testing method to analyze the bubble content and distribution in quartz crucibles for monocrystalline silicon ingots. Two different types of silica (SiO2) crucibles have been investigated, before and after use during Czochralski (Cz) silicon ingot production for solar cells. Samples have been cut from three different positions along the crucible wall and then investigated by X-ray tomography, optical microscopy and scanning electron microscopy. The unused samples were heat-treated at 1400 °C for 4 h in Ar at 15 mbar. It is observed that the crucible bubbles grow in size and density during the Cz process. More bubbles are detected closer to the inner part of the crucible wall after use in the Cz process. The results also indicate that there are some differences in quality between different crucible producers and that bubble formation and growth are significantly affected by the Cz process parameters, such as temperature and time.

Mar 1, 2017

By Gen Kamimura, Hiroyuki Matsuura, Wonjin Choi

Control of non-metallic inclusions in terms of morphology, number density or composition is essential to produce steel products having the desired mechanical properties.Though many studies have been conducted to clarify various properties and evolution mechanisms of inclusions at steelmaking temperature, it has been reported that the states of inclusions in final products are significantly different from those in crude steels for some steel grades. The present study has focused on the evolution of oxide and nitride inclusions in solid Fe–Al–Ti–N alloys during heating to increase the understanding of inclusion evolution in a simplified metal system. Compositional and morphological change of initial inclusions, as well as precipitation and growth of new inclusions have been observed even when the alloy was in a solid state.This behavior has been observed due to the change of thermodynamic stability and solubility of existing phases in inclusions.

Mar 1, 2017

By Ping-Ping Fan, Yong-Quan Wu

The polarized Brillouin scattering spectra were systematically measured to study the elastic properties of bulk hexagonal close-packed (hcp) ZnO single crystal in this paper. The peak polarizations of all modes in spectra were analyzed firstly. The elastic properties, such as the whole set of Elastic constants were accordingly calculated and compared with the previous literatures. Also investigated were the effects of the rotation of the sample in the (0001) plane perpendicular to the z axis on different acoustic modes. The results show that the quasi-longitudinal and quasi-transverse modes perpendicular to the (0001) plane act as the expected trigonometric function of the rotation angle,while the longitudinal and transverse modes on the (0001) plane remain constant.

Mar 1, 2017

By Jannette L. Chorney, Katie J. Schumacher, Katelyn M. Lyons, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating a new method of extracting and refining rare earth elements (REEs) from mineral ores and concentrates. The relative stabilities of various REE compounds and differences in vapor pressures are exploited to selectively separate rare earth chlorides, with dysprosium and europium chlorides used as proof-of-concept experimental materials.

Mar 1, 2017

By Tianzu Yang, Weifeng Liu, Lin Chen, Xinxin Fu, Shuai Rao, DUCHAO ZHANG

It is well known that the gold ores containing a high content of arsenic and antimony are very refractory. In this paper, the adverse effect of antimony on the extraction of gold by pretreatment-cyanide leaching was discussed in detail. Moreover, these processes of removing and recovering antimony from alkaline sodium sulfide or hydrochloric acid systems were introduced. Last bu not the least, a novel cleaning technology for recovering antimony from refractory gold ores was proposed. Antimony was dissolved into the solution with sodium sulfide and sodium hydroxide as leaching agents. And then pressure oxidation technology was applied to prepare sodium pyroantimonate from sodium thioantimonite solutions. This process is more promising owing to its high removal ratio of antimony, low production cost and environment friendly, which provides a positive guidance for the extraction of antimony from antimonial refractory gold ores.

Mar 1, 2017

By Shengli Wu, Feng Chang, Hua Lu, Jianliang Zhang

Kinetic studies of the blast furnace dust (BFD) reduction process have been carried out under non-isothermal conditions. BFD pellets were made with bentonite as the binder. A Comprehensive Thermal Analyzer (TG-DSC) was used to determine the mass loss of pellets, which were heated at three heating rates of 10, 20, 30 K/min up to 1493 K. Furthermore, the metallization rate and mineral composition of BFD pellets heated to several different temperatures were analyzed by chemical analysis and X-ray diffraction (XRD). It was found that, with its inherent carbon resources as the reducing agent, the metallization rate of BFD pellets could reach 88% at most. The reduction and weight loss process of iron oxides mainly happens above 1273 K. In addition, from application of the Coats-Redfern equation the apparent activation energy of the reduction from wustite to Fe was 443 kJ/mol and the mechanism was interface reaction R..

Mar 1, 2017

By Kristine Bruce Wanderley, Denise Crocce Romano Espinosa, Jorge A. Soares Tenório

Mining of nickel ores generates large volumes of waste that must be removed in order to eliminate water contamination and reduce environmental impacts created by waste barriers. In this context, the need for innovations concerning the recovery of magnesium present in the liquor produced by the leaching of nickel laterite with sulfuric acid arises. Therefore, this work aims to develop a study regarding the crystallization of magnesium from a synthetic liquor solution using a batch autoclave system at high temperature. Agitation speed was kept constant at 1000 rpm throughout the 3 h of batch reaction for temperatures of 230 and 200 °C. Aliquots taken at each hour were analyzed by ion chromatography to measure magnesium concentration. The highest magnesium removal was observed for temperature 230 °C. X-ray diffraction (XRD) and scanning electron microscopy (EDS-SEM) analysis proved that the product formed was magnesium sulphate monohydrate crystals. Thermogravimetric analysis coupled with a mass spectrometer was used for the evaluation of the thermal stability of magnesium sulphate monohydrate. It was found that MgO and SO2 were formed by the decomposition of the salt at 1100 °C.

Mar 1, 2017

By M. X. Huang, Y. Z. Li

The titanium diboride (TiB2)-reinforced steel composite, designed for automotive applications, exhibits a combination of high isotropic Young’s modulus and low density as compared to existing advanced high strength steels (AHSS). The steel-based composite is produced by in situ precipitation of TiB2 particles during eutectic solidification followed by hot rolling, and its microstructure displays a homogeneous distribution of both large primary TiB2 and small eutectic TiB2 particles in the ferrite matrix. Instead of interfacial debonding, particle cracking is the primary mode of damage, revealing very high interfacial strength. To investigate the intrinsic interfacial strength, a hybrid method combining both nanoindentation and finite element analysis (FEA) was used. A micron-sized sample containing a single crystal TiB2 attached to the ferrite matrix was fabricated by focused iron beam (FIB), and was compressed using nanoindentation with a flat indentation tip. By combining the compression and FEA results, the interfacial strength was therefore determined.

Mar 1, 2017

By Weizhi Zeng, Michael L. Free, Sayan Sarkar, Prashant K. Sarswat

Black Phosphorus was recently discovered as a 2D material and it exemplified huge prospects for application in electronics, optoelectronics, photonics and catalysis. It is a direct band semiconductor with tunable band gap varying from 0.35 eV (bulk) to 2 eV (single layer). But the layer dependent band gap of black phosphorus restricts it to make use of the full spectra of sunlight for absorption. First principle calculations were performed using ‘Quantum Wise Atomistic Toolkit’ package with Perdew-Burke-Ernzerhof (PBE) exchange-correlation for black phosphorus doped with non-metallic dopants of B, S and Se and metallic dopants of Ti, Mg and In. It has been found that doping with non-metallic impurities result in a small diminution of the band edges (0.96–0.57 eV), whereas doping with metallic impurities decrease the band edge drastically (0.85–0.025 eV). Moreover, it was also observed that dopants with an even number of valence electrons incorporated a metallic nature of black phosphorus, whereas dopants with odd number of valence electrons further attributed to its semiconducting features. Thus in a holistic discernment, black phosphorus with the incorporation of some dopants in appropriate amounts can absorb more visible range of the optical spectra, making it ideal for use in photovoltaics.

Mar 1, 2017

By Zan Yao, Sha Lv, Geoff Wang, Baojun Zhao, Zongze Huang, Jin Zou, Xiaodong Ma, Zhouhua Jiang

55SiCr steel is one of the important spring steels widely used in automobile manufacturing. The presence of micro inclusions in the steel can significantly influence a number of spring properties such as fatigue strength. It is important to understand the mechanism of the inclusion formation so that size and proportion of the inclusions can be controlled. Inclusions in Si-killed 55SiCr spring steel have been analysed by scanning electronic microscopy and electron probe X-ray microanalysis. The chemistry of the inclusions observed in 55SiCr steels can be represented by the SiO2–Al2O3–CaO–MgO system. It was found that the compositions of the inclusions cover a wide composition range, which indicates that these inclusions were formed from different reactions. The possible mechanisms of the inclusion formation are discussed. It would be possible to characterize and manage the inclusions in the spring steels deoxidized by Si.

Mar 1, 2017

By G. Djambazov, D. Shevchenko, D. Burnard, V. Bojarevics, K. A. Pericleous, W. Griffiths

Contactless ultrasound treatment can be useful for high-temperature or reactive alloys in the liquid state, where contact with an immersed vibrating probe is undesirable. The alternating component of the Lorentz force can generate sound pressure levels leading to cavitation of gas bubbles in the melt, through acoustic resonance. Resonance is a function of the speed of sound in the liquid, the shape of the volume containing it and surrounding boundary conditions. Induction forces applied to a crucible lead to bulk stirring and in general deform the free surface, whose precise shape may influence the resonance conditions. This effect is investigated here b ymulti-physics computer modelling. Calculated results for aluminium melts are compared with experimental data and conclusions are drawn as to the sensitivity to process parameters and the reliability of this type of ultrasound metal processing.

Mar 1, 2017

By M. A. Kader, M. A. Islam, P. J. Hazell, M. Saadatfar, J. P. Escobedo, A. D. Brown

The present study investigates the dynamic deformation mechanisms of closed-cell aluminium foams during low velocity drop weight impact with experimental analyses and finite element (FE) simulation.The evolution of foam collapse was explored with FE simulation using ABAQUS/Explicit. X-ray computed tomography (XRT) based geometry was reconstructed to understand the actual microstructural changes during impact. The experimenta lstress-strain response was compared with FE simulation with reasonably good agreement observed between FE prediction and experimental data. A vertical cross-sectional XRT slice was analysed at different strains from FE simulation to understand the pore collapse mechanisms.

Mar 1, 2017

By Wei Lv, Gangqiang Fan, Xuewei Lv, Kai Tang, Yingyi Zhang

The EAF smelting process of ilmenite concentrate consumes large amounts of energy. Semi-melting reduction can lower the reaction temperature and separate the iron and slag more thoroughly. However, this needs additives and pre-oxidation to promote the reaction. In this paper, the pre-oxidized ilmenite powders were reduced isothermally with graphite and Na2SO4. The influence of reduction conditions on the metallization ratio of samples, such as reaction temperature, and sodium sulfate additive were investigated. The results show that additive such as Na2SO4 can significantly decrease the melting point of pre-oxidized ilmenite concentrate.

Mar 1, 2017