Search Documents

By W. Kasprzak

Press-fit systems are widely used to seal oil lines in the automotive engine components. In the case studied a ball plug made from the 7075 A1 alloy was inserted into a 319 Al alloy cast component. The oil lines were subjected to the required component service pressure. This paper addresses the analysis of the ball plug/casting hole press-fit performance. The tools used to investigate the plug system included: the SEMIEDS technique for the assessment of the plug and the casting hole wall surface integrity; image analysis methods for the characterization of the ball plug/casting hole interface; matrix microhardness measurements of the plug and casting components; laboratory ball plug insertion, speed and force correlation; as well as the ball shearing mechanism analysis. Laboratory tests indicated that optimization of the aluminum matrix hardness in the 319 A1 alloy cast components resulted in considerable improvement of the press-fit system sealing properties.

Jan 1, 2002

By William A. Fuchs

A study of carbonaceous ore at the Santa Fe mine (Corona Gold Inc.) shows that there is no quantitative relationship between organic carbon content and preg rob, although much of this material preg robs. However, there is a relation between K20 and preg rob. Preg rob generally occurs only in those samples with greater than 2% K20. X-ray diffraction and chemical . studies show that the critical factor is the illite content of mixed (possibly interstratified) illite-smectite. Apparently illite, at a certain threshold, "geo-activates" the carbon. The potential for easily monitoring preg rob using a gamma ray spectrometer is discussed.

Jan 1, 1990

By Zhuoqing An, Qi Li, Zhancheng Guo, Yanling Zhang

Fluidized bed is an important iron-making reactor, especially for the finely sized iron-bearing materials. However, defluidization caused by sticking between particles extremely limited its wide spread commercialization. In this paper, apparent viscosity was put forward to express the ability of particles to resist movement, which is reasonably considered as the comprehensive results of interaction between particles. Meanwhile, an experimental measuring method of apparent viscosity of particles was proposed, during which the torque exerted on the rotating blade in a particle layer is measured, and then the apparent viscosity is obtained based on the motion equations of powder particles. Further, the apparent viscosity of iron particles was measured by using of this method, and the effects of shape, size, and temperature were examined. The data can provide important information for understanding when and why defluidization happened.

Jan 1, 2015

By Daniel Gauthier, Patrick Sharrock, Cedric Verwilghen, Gilles Flamant, Ange Nzihou, Jocelyn Ramaroson

Clean processes are needed to dispose of many wastes. The incineration of 1 ton of municipal solid waste generates 6000 Nm3 of combustion gases contaminated with heavy metals and other pollutants. Gas scrubbing processes are required to clean incineration fumes in order not to transfer pollution to the atmosphere. We are investigating the use of Hydroxylapatite (Ca-HA) particles for use as sorbent for the removal of volatile heavy metals. We have carried out the synthesis of Ca-HA by two precipitation methods from solution and obtained solids with specific surface areas reaching more than 100 m2/g. Preliminary adsorption experiments were conducted in a horizontal furnace by mixing Ca-HA with 5% by weight of cadmium chloride in solid state. The mixture was heated to 600°C under air atmosphere during 6 hours. Chemical analysis of the solids confirmed that 85 % of the cadmium was retained in the solid phase. Such laboratory results showed that Ca-HA is capable of adsorbing cadmium chloride vapors, and pilot scale studies confirmed cadmium abatement in an industrial context.

Jan 1, 2008

Rotary kiln incinerators are widely used in the incineration of various types of hazardous wastes. However, the complex transport processes within the incinerator are not well understood. Due to large variations in waste types and difficulties in feed characterization, the incineration process meets great challenges in a smooth operation, and expects uncertainties in the process chemistry and emission control. In order to get better understanding of the incineration process, process simulation was made on the kiln behavior by using Computational Fluid-dynamics (CFD) to characterize gas flow, temperature distribution and waste combustion in the incinerator. Temperature measurement was conducted in an operating incinerator to validate the CFD model. This paper addresses the environmental issues related to the hazardous incineration process, and reports the recent simulation results on gas flow and mixing, combustion heat transfer, and potentials to reduce emissions.

Jan 1, 2002

By M. E. Reed

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed) which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons Feed System could deliver the following benefits to Flash Furnace operation: ? Accurate pulse-less delivery of feed material to the head of the burner leading to improved combustion performance and process stability; ? Highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; ? Decreased pressure pulsation in the furnace due to improved combustion control and performance; ? Decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear; Plant measurements have indicated a correlation between the discharge of concentrate from the drag chain conveyor and high speed pressure fluctuations in the flash furnace settler. Pilot scale test have been conducted to illustrate that the system delivers pulse-less feed to the burner with even feed distribution axially.

Jan 1, 2006

By Thomas Havlik

It is proposed to realise the direct leaching, during which will be generated elemental sulfur and not sulfate or sulfuric acid as end product, under conditions that sulfur will not cover the leaching surface and Hot hinder the leaching course. The following improvements have been considered: -use of organic sulfur solvents -ultra high-frequency leaching -ultrasonic leaching -use of surface detergents or surfactants in leaching processes -simultaneously crushing and leaching These proposals are under investigation and preliminary results are promising

Jan 1, 1996

By Luis Hoyos-Reyes, Jesus Gonzalez-Trejo, Adriana Cervantes-Clemente, Marco Gutierrez-Villegas, Manuel Palomar-Pardave, Cesar Real-Ramirez

Recent improvements on Peirce-Smith Converters (PSC) have combined numerical and physical simulations. However, most of the physical simulations have been carried out in cold-water models with only one tuyere. Several authors have proved that 2D numerical simulations do not reproduce the hydrodynamic behavior observed in physical simulations. On the other hand, most of the 3D numerical models have used a PSC thin slice with only one tuyere, but symmetric boundary conditions on the virtual walls have been imposed in order to reproduce the behavior of the whole converter. Therefore, there is no coincidence with the rigid walls of the physical models. The aim of this work is to quantify the effect of the virtual walls boundary conditions of a PSC thin slice and to determine the minimum number of tuyeres to characterize the fluid flow behavior of the entire converter.

Jan 1, 2009

By C. L. Lin

Transformation of linear grade distribution to volumetric grade distribution has been used to estimate the actual mineral liberation during wet, batch, ball mill grinding of a copper ore. The degree of liberation based on the multicomponent-multisize grinding liberation model using volumetric grade is lower than the apparent degree of liberation estimated from using King's linear intercept model.

Jan 1, 1987

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By Toshiyuki Kozuka

CdTe metal composite semi-conducting material has high potential in good performance of energy conversion efficiency for solar cell and there is much room for improvement of the performance by developing a process of making a thin CdTe film. In this paper, the imposition of intense magnetic field on CdTe electro-depositing surface is proposed, which is one of the possibilities for improving the energy conversion efficiency. In the experiment, cryogen-free super-conducting magnet up to 5T was used and CdTe film was deposited electrically in -0.72V vs. SHE The electrolyte was Cd and Te ammonia alkali solution with controlled temperature in the acrylic cell of 70mm diameter. Electro-deposition behavior of CdTe has affected by the imposition of the intense magnetic field due to microscopic convection in the vicinity of the depositing surface. Electro-deposited surface of CdTe becomes smooth due to microscopic convection around the surface, and the crystallization behavior is also affected, where crystallization temperature and the grain size is changed by the imposition of intense magnetic field.

Jan 1, 2003

By Michael Stelter

Lead alloys are a typical material for anodes in technical electrowinning processes. The life time of those anodes differs from 2 years to more than 5 years in tankhouse practice depending on the type of alloy, the mechanical damaging and last but not least the chemical corrosion in the electrolyte. Different types of alloys, such as PbSb, PbCa, PbAg, PbSnCa or PbAgCa have been developed and used in the past, their rate of corrosion being more or less a philosophic discussion. Comparable investigations on the corrosion behavior in dependence of the concentrations of alloying metals, the grain structure and the mechanical and thermal treatment during production have not been conducted before. In the last years the Institute for Nonferrous Metallurgy and Purest Materials of the TU Bergakademie Freiberg investigated the corrosion behavior of the typical lead alloys for metal electrowinning under comparable conditions. Correlations between different alloys, mechanical treatments like rolling or thermal treatment like annealing to the rate of corrosion were made, leading to the conclusion that grain structure and grain size are of eminent importance for the rate of corrosion in technical electrolytes. From these results new and optimized lead alloy anodes can be produced with an increase in life time of the factor 3 ? 5. The optimized lifetime in terms of corrosion stability can not protect from mechanical damaging in tankhouse practice, but with a careful practice the increase in lifetime can save a lot of money and problems.

Jan 1, 2006

By William J. Pardee, Michael A. Shaff

"Deeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will accelerate productivity growth and materials science application through the ease with which they can be modified to accept new materials knowledge and sensors. Carbonization of resin matrix carbon fiber composites, specifically, is a violent solid state chemical reaction with large stresses due to gas pressure, matrix shrinkage, and differences in thermal expansion. The matrix strength falls sharply, then rises again during the process. At least two competing reaction paths are important; the first cleaves methylene bonds, reduces toughness, density and stiffness; the second reforms those bonds, ultimately resulting in aromatic ring condensation that increases density, strength, and modulus. Since these reactions have different temperature dependencies, one can expect to shift the process towards the second path by changing the heating rate, but that change must be accomplished without producing macroscopic interlaminar crack growth. To accomplish this, we employ gas sensors to infer matrix chemical state and acoustic emission to identify microstructural changes and to recognize brittle fracture. The latter does not prevent delamination, but is important in testing models for the causes of delamination and in improving the processing cycle. This paper describes a control strategy to accelerate the process while still lowering the risk of failure.IntroductionDeeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will be more easily modified to accept new materials knowledge and sensors, thus accelerating productivity growth. Such a control strategy for carbonization control is described below.Carbon-carbon composites are time consuming and costly to manufacture. Processing methods have been developed empirically and are usually very conservative because the process often fails when any change is made. Apparently minor changes in materials or geometry can produce failures that are difficult to diagnose and correct. We will describe below several essentially unavoidable sources of variability. These are best dealt with by applying materials science to adapt (i.e., closed loop control on materials properties) the process in real time to reduce the effect of unavoidable model idealizations, material variability and environmental noise. The most critical issue in control of the carbonization process control is avoiding catastrophic delamination. The strategy developed below makes use of a priori materials knowledge and real time sensors to accelerate the now very slow process without destroying the material, and without requiring unreasonable resources to determine the statistical properties of the material."

Jan 1, 1988

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya, Paul Cilino

"This paper focuses on generating a quantitative microstructure prediction model for Scanning Laser Epitaxy (SLE) process based on coupled flow-thermal modeling using Finite Volume method. SLE is a laser-based additive manufacturing process for the deposition of equiaxed, directionally solidified and single-crystal nickel superalloys through the melting of alloy powders onto superalloy substrates. In the current work, the detailed effects of natural and Marangoni convection on the flow field are studied and the results are analyzed in terms of the temperature gradient, vorticity parameter, melt pool dimensions and mushy region extent. The detailed property data of the processed superalloy and the laser scan path are incorporated in the model to predict the microstructure in realistic scenario. An optimization study is carried out to evaluate the critical parameter values at which the columnar-to-equiaxed and the oriented-tomisoriented transition take place. This work is sponsored by the Office of Naval Research through grant N00014-11-1-0670.IntroductionSLE is a laser-based additive manufacturing process for the creation of structures in equiaxed, directionally solidified and single-crystal nickel superalloys through the selective melting and resolidification of superalloy powders. In SLE, a tightly focused laser beam is guided by a highspeed galvanometer scanners allowing for tight control of the amount of energy being applied to the top of the powder bed, as well as the speed at which the melt pool moves across the substrate. Under the proper operating conditions and with sufficient substrate meltback, the solidification microstructure follows the morphology of the underlying substrate, allowing for directional and even SX growth.Several reports on the modeling aspects of laser cladding-based additive manufacturing approaches can be found in the literature. Approaches based on Finite Element Methods (FEM) and Finite Volume Methods (FVM) are employed for the thermal modeling of the system [1, 2]. Gaumann coupled the Columnar to Equiaxed Transition (CET) modeling with the Rosenthal solution in earlier work based on laser cladding [3]. Rappaz et. al. provided a detailed modeling of the microstructure/columnar orientation based on the solidification velocity and crystalline orientation [4]. This approach is based on the selection of the growth direction that closely follows the melt pool normal direction. Later on, substrate orientation is also taken into account [5, 6]."

Jan 1, 2013

Convential smelting of copper - cobalt - iron sulphide concentrates result in th eoxidation of cobalt and iron, which are subsequently lost into the slag. The emission of SO2 bearing gas from smelting causes serious health and environmentsl problems. In this investigation, three different types of copper - cobalt - iron sulphide concentrates, derived from froth flotation, were investigated, the concentrates, each containing more than 40 wt % percent gangue material, were directly reduced in the presence of lime and corbonin the temperature rnage of 1073 K - 1573 K, fo rthe production of an alloy containing copper, cobalt and iron. We demonstrate the basic principles of process physical chemistry for the recovery of alloy by carrying out a detailed process analysis utilising the predictions from thermodynamic equilibrium and results from the kinetics of reduction reaction. The effect of temperature on the reduction kinetics and alloy formation were determinedand analyzed in detail.

Jan 1, 2012

By Dietmar Eifler, Benjamin Jost, Marcus Klein

This paper focuses on the ductile cast iron EN-GJS-600 which is often used for components of combustion engines. Under service conditions, those components are mechanically loaded at different temperatures. Therefore, this investigation targets at the fatigue behavior of EN-GJS-600 at ambient and elevated temperatures. Light and scanning electron microscopic investigations were done to characterize the sphericity of the graphite as well as the ferrite, pearlite and graphite fraction. At elevated temperatures, the consideration of dynamic strain ageing effects is of major importance. In total strain increase, temperature increase and constant total strain amplitude tests, the plastic strain amplitude, the stress amplitude, the change in temperature and the change in electrical resistance were measured. The measured values depend on plastic deformation processes in the bulk of the specimens and at the interfaces between matrix and graphite. The fatigue behavior of EN-GJS-600 is dominated by cyclic hardening processes. The physically based fatigue life calculation “PHYBALSIT” (SIT = strain increase test) was developed for total strain controlled fatigue tests. Only one temperature increase test is necessary to determine the temperature interval of pronounced dynamic strain ageing effects

Jan 1, 2015

By Juergen Antrekowitsch, Stephan R. Steinacker

The main aim of the electric furnace treatment in the primary copper industry is the reduction of valuable metals such as zinc, lead or copper itself. On the one hand legal restrictions for the further use of the treated slag are constantly getting stricter while on the other every type of loss in the oxidic phase leads to economic disadvantages. In order to fully understand and to improve the process, kinetics during the reduction play an essential role. In the first part, this paper highlights the theoretical background of the reduction process, while the following chapters present experimental aspects and results from laboratory scale trials at the Montanuniversitaet Leoben. In addition, the comparison between the chemical reaction and the diffusion model plays a continuously important role. By investigating the reducibility of electric furnace slag, process adaptions and ameliorations are developed.

Jan 1, 2016

By J. D. Zhu, T. Ohmichi, H. Yasuda, S. Kashiwai, I. Ohnaka

"Since the casting process affects the properties of castings, its computer simulation has been greatly developed in the last decades. This paper presents our recent works, especially on mold filling simulation, because most casting defects such as porosities and inclusions that greatly affect the properties originate during mold filling. The first topic is the mold filling simulation with consideration of cavity pressure change during mold filling, including direct observation of flow phenomena with X-ray and pressure measurement. The second .one is the mold filling simulation in the lost foam process, in which gasification of polystyrene pattern and gas outflow through the coating and mold have been considered. The simulation can predict not only the mold filling sequences but also periodical vibration of the gas layer between the melt and pattern. The third one is the comparison of simulation of Al melt flow in a metallic runner and direct observation through a transparent mold, showing that the entrapped gas or inclusions is expelled ahead through the melt and its simulation needs very fine meshes. These examples show that the comparison of simulation and observation is very important to develop the numerical simulation further.IntroductionThe mechanical properties of castings are greatly affected by casting defects such as porosities and inclusions, and solidification structure. Although recently the structure simulation has greatly progressed [1-4 ], the application in plants is very limited, because the structure is mostly determined by chemical compositions and cooling rate, enabling us to estimate it from the structure of past similar castings without simulation.On the other hand, the casting defects often vary with each casting or time. Among the defects, porosities and inclusions are main causes to deteriorate the properties and mostly originate during mold filling. Therefore, a lot of efforts to simulate the mold filling and estimate those defects have been made in the last decades [l,5,6]. These efforts have been mostly to develop numerical techniques to solve the Navier-Stokes equation. However, the flow phenomena in molds have not been well understood, because the direct observation of the flow phenomena in mold is not easy. This means the accuracy of the simulation is still not clear."

Jan 1, 2000

By Alan M. Peel

"Over the past years there has been an increasing demand by aluminium cast -house operations to obtain a greater return from their existing installed plant. This has included increasing existing furnace production capacity to match new and higher downstream production requirements, reducing melt losses and more efficient alloying.The paper discusses how Electromagnetic Pumping, which was developed for the combined purpose of;1. Melting light gauge aluminium scrap with a reduced melt loss and; 2. Effective circulation of the aluminium melt,has established its self in recent years, as an effective means of satisfying many of these industry requirements, but how it has also provided many other additional operational benefits to the aluminium cast house.The paper will discuss operational performance of the system with a particular emphasis on its effect on the metal bath quality (alloying, chemical and temperature homogeneity), metal recovery and increased production due to the high circulation.The technology having now been adopted by a variety of industry leaders has a number of prominent references and the paper will discuss the operational benefits and experiences from some of these."

Jan 1, 2000

By Roberto Giovanardi, Isabella Lancellotti, Luisa Barbieri, Ercole Soragni, Fernanda Andreola

"Recovery of precious metals (PMs) is a present topic, as they are used almost in every electronicelectric device. Gold is the second PM in order of consumption (following silver) and it is almost ubiquitary in electronics where it mainly finds application to produce bonding wires in integrated circuits and as a coating for contacts and connectors. Given this, discontinued electronic and, with a minor role, electric devices may represent a primary source of PMs as gold mines or jewelery wastes.At present the recovery of gold from such waste is generally accomplished by two strategies: by oxidative thermal treatment followed by metallurgical or chemical processes or by cyanide chemical etching; both techniques do not represent the optimum as the first one deserves a great amount of energy and non-combustible pollutant slag and fumes are produced, while the second procedure comports the use of a highly pollutant agent as cyanide.The aim of this work is the characterization of different electronics scraps to evaluate the gold concentration, and the selective recovery of this metal using enviromentally-friendly techniques. In particular, a new process was developed in order to overcome such environmental and efficiency issues. The process reaches the goal of detach the gold film from the substrate by selective leaching of the supporting metal.IntroductionThe treatment of waste from electrical and electronic equipments is a current topic as their role in modern life is increasing. The disposal of such waste represents both an environmental and an economical concern due to the vast amount of both precious and non precious metals.The use of precious metals (PM) in this field is of primary importance given PM’s unique properties, which give to each of them a specific and irreplaceable role. Silver is the most used, with a demand of over 5000 tonnes per year, mainly for switches and contacts in electric appliances. Gold is the second PM in order of consumption (over 250 tonnes per year and 8% of the total demand) and it is almost ubiquitous in electronics where it finds application to produce bonding wires in integrated circuits and as a coating for contacts and connectors. It is also used as solder in integrated circuits (in alloy with tin) or for wide coatings where it ensures protection against corrosion. Palladium, platinum, rhodium and iridium follow in order of consumption [1- 3]."

Jan 1, 2008