Search Documents

By Andrey Dmitriev

The solution of set of equations for the bottom zone presented by a condition of a thermodynamic equilibrium, namely, an equilibrium constant of wustite reduction by carbon oxide, material and thermal the balances, supplemented by the equation of the heat balance for the top zone, allows to calculate the base indices of blast furnace smelting. The calculated indices are extreme accessible at the given parameters of charge and blast. Application of actual degrees of the use of gas instead of equilibrium allows the calculations of actual indices of the blast furnace smelting process.

Jan 1, 2006

By Tracy Morris, Weldon Read, Luis Navarro

"During the leaching of anodic slimes, tellurium dissolves into the leach liquor together with copper and must be removed before the solution is sent to liberator cells for copper recovery. Prior to the installation of autoclaves, tellurium was precipitated using raw slimes that caused a recirculation of tellurium in the leaching circuit. After autoclaves were installed the old leach tanks were converted into tellurium reactors utilizing copper chips, steam and agitation to form a copper telluride precipitate. Tellurium levels of less than 10 rng/L are achieved in a timely manner.IntroductionThe electrolytic refining of copper consists of an electrolytic cell provided with an anode of impure copper, a cathode of substantially pure copper (starter sheet) and an electrolyte made of copper sulfate and sulfuric acid [1]. When a direct electrical current is passed between the anode and cathode inside the cell, the impure copper anode dissolves in the electrolyte and pure copper is plated onto the cathode. During this operation, many of the impurities are deposited on the bottom of the cell as an anodic slime residue composed of insoluble chemical compounds. Slimes are a major source of rare and precious metals in the copper industry [2-5],In the Amarillo Copper Refinery (ACR), the anodic copper slimes are sent to the Precious Metals department in order to extract and then refine the gold, silver, platinum and palladium from them. The remaining impurities, in the form of a soda slag or copper slag are sent to the Hayden smelter for further processing. Copper telluride is sent to the Selenium/Tellurium department inside the plant for selenium and tellurium recovery. During the leaching process of the anodic slimes, copper, tellurium, and other metal species in the slimes are dissolved into leach liquor that cannot be returned to the tankhouse unless the tellurium concentration is below 10 mg/L."

Jan 1, 2012

By V. K. Kalyani

The present paper discusses a three layer feed forward artificial neural network (ANN) model, trained using the error back propagation algorithm, has been established to simulate the column flotation circuit used for beneficiation of Sillimanite. Parameters such as superficial air velocity, wash water rate, froth height, % solid, feed velocity, sodium silicate and oleic cid are considered as process operating variables and % yield of Sillimanite is the output of the experiment. The results from the ANN modeling, involving the non linear relationship between inputs and outputs, indicate good agreement with experimental observations. The network model validates the experimentally observed trends. The optimal model parameters in terms of network weights have been estimated and can be used for computing parameters of the process over wide-ranging experimental conditions.

Jan 1, 2006

By Y. H. Wang, S. Kou

"Three-dimensional weld pool convection was computer simulated using dimensionless variables. The electromagnetic force, the buoyancy force and the surface tension gradient on the pool surface were treated through the use of the dimensionless electromagnetic force, the Grashof number and the Marangoni number. Other typical dimensionless numbers such as the Prandtl number and the Peclet number were also used. The calculated and experimentally observed fusion boundaries were compared. The convection patterns were shown and the effect of the Marangoni number was demonstrated. IntroductionSeveral weld pool convection models have been developed by Oreper et al. (1,2), Chan et al. (3) and Kou et al. (4). These models describe two dimensional convection in stationary weld pools in a semi-infinite workpiece. Since the vast majority of arc welding practices involve a moving heat source and weld pool, and the workpieces are finite in thickness rather than semi -infinite, a 3-D convection model for a moving heat source and a workpiece of finite thickness is expected to be much more useful.Weld pool convection can strongly affect the structure and properties of the resultant welds. Variations in weld characteristics which are likely to occur from changes in weld pool convection are: weld penetration, macrosegregation, gas porosity, solidification structure, undercutting and surface smoothness. Apparently, the quantitative understanding of convection and heat flow in weld pools is of considerable practical interest. Mathematical models describing convection and heat flow in weld pools are essential, not only because of the quantitative understanding they provide, but also because of the difficulties associated with the experimental measurements of weld pool convection. These difficulties are mainly due to the fact that only surface flow, rather than the overall convection pattern in the weld pool, can be observed. In fact, due to arc glow even the observation of surface flow can be rather inconvenient."

Jan 1, 1986

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011

By Eiki Ono, Atsushi Yamatodani, Shigeru Sunagawa, Yasushi Takasaki, Atsushi Shibayama, Yasunori Higuchi

"During metallurgical processing of non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product.In this research, some experimental feasibilities were investigated to recover/remove Cu and As from the residue. Primarily, the removal of As and volatilized materials from the residue was examined by pyrometallurgical treatment (dry-process). In the second stage after treating the residue with a dry-process, leaching and solvent extraction as hydrometallurgical treatments (wet-process) were also investigated by using H2SO4 solution as a two stage leaching treatment, to dissolve various metals from the leach residue. Then, solvent extraction was examined by using LIX-84I as an extractant to recover and separate Cu from impurities from the final (2nd) leached solution. For the leaching stages, the removal of 90 % As and the leaching rate of 85 % Cu could be achieved by 0.25 mol/l and 1.0 mol/l H2SO4 solution, respectively. On the other hand, the extraction of over 90 % Cu and stripping was carried out by solvent extraction. 1. IntroductionIn metallurgical process for non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product, i.e., flue dust, slug and so on. The smelting residue includes some useful metals and undesired toxic materials; Cu, Pb, Ca and As, etc.In Japan there is one undisclosed place stockpiled with 10,000 ton of smelting residue from abandoned smelters about 25 years ago. Therefore it is necessary to reduce the residual amount for space and environmental protection including water treatment by separating and removing toxic materials."

Jan 1, 2008

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By Ruixiang Wang, Jinhui Li, Youjun Xiao, Daoling Xiong, Hao Chen

"Leaching solution prepared from spent battery materials contains large quantities of valuable metals, such as Cu, Ni, Co, Mn and Fe. Therefore, recovery of valuable metals from acidic polymetallic aqueous solutions is of great importance for every plant. In this work, a method is introduced of recovery of Ni, Co and Mn from polymetallic solution prepared by leaching spent battery material. The basic concept includes copper was removed through replacement by iron powder followed by iron precipitation in goethite method. The experimental results show that Cu can be removed 99% at least through replacement by Fe powder, and the removal of Fe can achieve 99% by goethite method. At the same time, the loss of Ni, Co and Mn are about 2%, 3 % and 2%, respectively. The process of differential removal of metals can be selected as the treatment alternative that combines simplicity, efficiency and reliability with low capital and maintenance costs. The purified solution which only contains Ni, Co and Mn can be used to prepare NixCoyMnz ternary system precursor.1 IntroductionNickel and Cobalt are very important metals which are applied in many fields, such as energy material and support material for some new material field. The world demands for such metals is progressively increasing, while raw resources are being depleted and with the constraints raised by the Law and related legislation assigned to protect the environment from hazardous wastes in the world. Nowadays study on reutilization of waste materials has great significance for achieving secondary resources recycling and preventing environmental pollution. There are many hydrometallurgy methods applied for dealing with these wastes, while they usually contain large quantities of valuable metals, such as Cu, Co, Mn and Ni, as well as impurities, such as Fe, Zn, and etc. Therefore, proper treatment of these leaching solutions prior to their discharge is of great importance, so that the contained valuable metals can be recovered.Separation and extraction of metals from leaching solution can use some methods through solvent extraction[l,2], ion exchange[3,4], precipitation with sulfide[ 5] or alkali[ 6] and electrolytic recovery[?]. Among the appropriate treatment alternatives, replacement and differential precipitation is the most attractive treatment that combines simplicity, efficiency and reliability with low capital and maintenance costs."

Jan 1, 2011

By J. N. Hryn

This paper describes some of the work done in Phase 1 of a multi-year, five-phase program aimed at demonstrating the economic feasibility of producing commercial-scale quantities of commodity materials derived from salt cake residue-oxide. The amount of salt cake generated annually in the U. S. is estimated to be 510,000 tons, including 340,000 tons of residue-oxide. Used beverage can (UBC) processing accounts for the majority of residue-oxiae that could be made available for further processing into commercial products. To characterize the composition of residue-oxide. eight residue-oxide samples from various secondary processors were obtained and analyzed. Surprisingly, the composition of residue-oxide was found to be independent of source or alloy family being processed, with? the exception of slightly elevated silicon levels in 3XXand UBC residue-oxide samples. Major phases detected in the residue- oxide were? alumina, spinel, and aluminum hydroxides. Preliminary economic analyses indicated that the refractory market appears to be the best choice for high value-added products produced from residue-oxide with minimum processing. Bench-scale tests indicated that low silicon containing residue-oxide is ready to enter this market, but the elevated silicon content of UBC and 3XX residue-oxide preclude this possibility. A separation technology should 'be developed to remove silicon-containing . species from the alumina and spinel values Present in residue-oxide. This technology would then allow UBC and 3XX residue-oxides to be converted to significantly higher value-added products.

Jan 1, 1995

By B. Q. Li, S. P. Song

"Numerical models are developed to represent complex electromagnetic, free surface deformation and fluid flow phenomena in floating zone refining processes with radio frequency inductive heating. The computational methodology is based on the coupled finite/boundary element method for the electromagnetic field distribution and the Galerkin finite element method for magnetically driven fluid flow and free surface profiles of the molten zone. With the models, the complex transport and free surface phenomena in a floating zone system can be studied as a function of various operating conditions including applied current, frequency, inductor position and shape, surface tension, floating zone diameter and height. Results show that the equilibrium shape is sensitive to the height of the molten zone and that the free surface shapes can have a significant effect on the melt flow in the molten zone. Our extensive simulations also suggest that to ensure accurate results, the same mesh should be used, whenever possible, for both the electromagnetic forces and fluid flow calculations.1. IntroductionThe floating zone processes have been widely used in the materials industry to grow ultra-pure rare earth metal or semiconductor single crystals for sensor or electronic applications that have a tough demand on purity. Developed based on the principle of magnetic melting/levitation, the processes possess a main advantage that the molten zone is supported in air by the electromagnetic forces generated by the coil (see Figure 1), and therefore is free from contamination from a container. Consequently, the final products made from the floating zone processes have higher inherent purity than those by other techniques [1-4].Complex physical phenomena occur in the floating zone processing of materials. These include free surface deformation, magnetically-driven melt flow, which may be turbulent or mildly turbulent [5] depending on the applied conditions, and solidification. Thermal stresses also develop in the single crystals, which are affected by the flow and temperature field and which can have direct implications to qualities of single crystals [6]. An understanding of the fundamentals governing these physical phenomena can be of critical value in elucidating the physics that controls the properties of the metal or semiconductor crystals being produced, thereby providing a rational basis for process improvement and quality control."

Jan 1, 1997

By Rumen Markov, Lubomir Kuzev

"The treatment technologies for municipal solid waste (MSW) are effective mainly for components sized over 40 – 50 mm. This fraction is separated by screening in the beginning of the process. Usually the undersized product is deposited without additional treatment. Its quantity is variable from several up to 30 – 40 % of the total MSW. Both oversized and undersized fractions are formed by all types of primary matter. Adapted technologies from mineral processing will provide a suitable technology for treatment of MSW under 40 – 50 mm. The MSW content depends on the geographical location, the degree of urbanization and other factors. The methods can be applied for separations of different components suitable for recycling or other utilization are: • Separation by density; • Separation in thin liquid layer; • Selective grinding and screening; • Flotation, etc. Introduction Municipal solid waste (MSW) represents an integral part of public urbanization. However, there are some drawbacks stemming from MSW, in regard to its collection, transport and elimination. Different approaches exits worldwide for tackling the problems arising from MSW. For a short period of time, the attitude towards MSW has evolved in several levels, each further level being characterized by higher percentage of utilization of MSW components. Thus, the bottom line has been shifted from safety storage towards processing that includes recycling and maximal utilization of MSW components. Technologic processes applied for treatment of MSW have a common feature – that the fine components, having sizes under 20 mm, 30 mm, 40 mm, or 50 mm are excluded from treatment process trough screening, and in most cases diverted without any additional treatment to preliminary prepared storage sites. MSW in Sofia – current situation The amount of MSW collected daily in Sofia as around 1000 t/24 h. It is stored or baled. Baling is a spare alternative of storage, since baling insures only temporal keeping of MSW, till the building of suitable storage site where the bales will be transported and buried. The morphologic composition of MSW in Sofia has been determined several times at different time intervals, from some Bulgarian organizations as well as from the Japanese organization JICA. So far, however, there is still a lack of enough systematical and comprehensive study. Generalized results from the studies on the MSW components, as well as some important parameters are given in Table 1."

Jan 1, 2008

By Tracy Morris, Weldon Read, Luis Navarro

"Bismuth is a recognized contaminant in the electrolytic refining of copper that can render many cathodes to be outside ASTM standards and unsuitable for copper rod and other downstream products if not carefully controlled. This paper portrays the performance of Molecular Recognition Technology (MRT) for bismuth removal at the Amarillo Copper Refinery (ACR) and describes how the highly selectivity gel has been successfully used to achieve good bismuth removal and how many pit falls and draw backs have been overcome.IntroductionASARCO operates one of the largest copper refineries in the world at Amarillo, Texas. The main feed for this refinery is produced at the Hayden smelter in Arizona. During the operation of this smelter a variety of metals are carried as impurities in the copper anodes because of the diversity of concentrates and residue products used as raw materials in the smelter feed mix. Even though the impurities are concentrated enough to be detected at the smelter, it is difficult to remove them completely. A simple way to control impurities at the smelter is to minimize the addition of material with a high concentration of impurities to the charge in order to reduce the output of this metal species. All this leads us to have a ""refinery problem"" [1,2,3]."

Jan 1, 2012

By L. B. Tsymbulov

Sulphide melts formed in the course of smelting of nickel and copper-nickel feed (matte) actually are sulphide-metallic melts since sulphur contained in the melts is in deficiency with respect to metals. The level of metallization is rather relevant feature of sulphide melts and is widely used in calculating material and heat balances for pyrometallurgical processes. Despite of the above parameter? importance, the investigators have no single opinion on what should be understood under metallization level and the method of its determination. In the present study we present the results of our own experimental and theoretical researches that have allowed determination of some mechanisms of sulphide melts? crystallization. Based on the mechanisms revealed new scientifically justified approach has been offered for determining level of metallization of the components present in sulphide melts. It has been demonstrated that sulphur distribution between the melts is substantially different from generally accepted concept.

Jan 1, 2006

By Richard L. Summers

The shaped charge has proven in various military and industrial applications to be an effective penetrator of materials. Upon initiation a detonation wave traverses the explosive billet, collapsing a metallic liner and creating a jetting process. From multiple non-simultaneous flash radiographs of the jet in free flight, the observer can study the collapse, formation, and growth of a shaped charge jet. Digitization of a particulated jet's position and shape from the radiograph into electronic storage files provides the experimentalist with an efficient basis for data reduction. With the aid of a simple personal computer, one can in a matter of minutes generate a wealth of information concerning jet formation after initiation and thus gain insight into the quality of its manufacture, design, and assembly. This paper will in detail explain the methods in place for fully automated data reduction of radiographic films. Methods of computer aided digitization of particulated jets and analysis of physical jet characteristics and performance will be discussed.

Jan 1, 1992

By E. A. Román

An ion exchange pilot plant, provided by Mesco Inc., was tested for antimony control in the electrolyte at three Chilean tankhouses for copper electrorefining: Chuquicamata, Potrerillos and Enami -Ventanas. The pilot plant, with a nominal extraction capacity of 1.2 kg Sb/day, worked connected to both experimental and commercial circuits, performing a total of 310 loading and elution cycles. An innovation in this process is the use of a chelating organic elution reagent, which presents some advantages over the traditional 6N HCI. This new eluent is amenable to continuous regeneration and recycling with high recovery efficiency. Antimony removal starting at initial, concentrations of 0.5 to 0.6 g/l of Sb down to steady concentrations of 0.1 to 0.0.6 g/l Sb, resulted in the production of High Grade copper cathodes with Sb contents below 0.1 ppm. Anodic slimes showed Sb contents below 1%.

Jan 1, 1999

By H. J. Garcia

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. Initial sodium cyanide concentration was 300 ppm at pH 10.5. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. The activation energy and the frequency factor were determined to be { A }Ea = 5.45 Kcal/mol and A = 1.28 x 10-2 sec-1, respectively. Based on these values, thermodynamic properties of an intermediate activated complex were assessed. All tests resulted in cyanide concentrations less than 0.1 ppm in about 35 days at 250C, whereas at 350C the time of biodegradation to reach this cyanide level was 30 days. Kinetic data were also established to relate biodegradation to amount of inoculum. The maximum theoretically-attainable rate, Vm , and the optimum amount of inoculum, K , were determined to be 4.8 x 10-4 M NaCN/day and 7.5 % of amount of inoculum. With respect to the mechanism of biodegradation, cyanide was shown to decompose to carbonate, bicarbonate and ammonia. Titrimetric analyses revealed concentrations of 5.6 x 10-3, 4.8 x 10-3 M, and 70.2 ppm for carbonate, bicarbonate and ammonia, respectively. The average cell population was determined to be 3.75 x 108 cells/mL.

Jan 1, 1994

By Yukihito Sasaki

Sumitomo Metal Mining Co. Ltd. planned an expansion program for the Toyo smelter and refinery in order to increase the production capacity of electrolytic copper to 450,000 tpy in 2007. Regarding the flash smelting furnace, a drastic increase in the average concentrate smelting capacity from 2,300 tpd to 3,950 tpd was required to achieve the plan. It was necessary to examine the performance of the Sumitomo concentrate burner when the feed rate was considerably increased. The authors developed a mathematical model to describe the combustion phenomena in the Toyo flash smelting furnace. This model was developed incorporating the fluid flow, heat and mass transfer, and chemical reactions of the copper concentrate and ancillary fuel. The copper concentrate was considered to mainly comprise chalcopyrite (CuFeS2). The reaction of CuFeS2 was assumed to consist of two steps, namely, the decomposition of CuFeS2 and the oxidation of the resulting pyrrhotite (FeS) and sulfur (S). The combustion phenomena in the furnace at the increased feed rate were predicted using this model. It was found that the Sumitomo burner was capable of enhancing the smelting capacity. This is attributed to the wide dispersion of the concentrate particles caused by an increase in the particle mass and a long residence time in the reaction shaft; this is due to the low temperature of the reaction air. However nonuniformity of the reaction in the reaction shaft was enhanced with the increased feed rate. In order to improve the nonuniformity of the reaction, an increase in oil-burner oxygen and an enlargement of the diameter of the dispersing cone were useful. By combining the expertise of the Toyo smelter staff and the calculation results, the concentrate smelting capacity of the Toyo smelter has been stably increased to 3,600 tpd thus far, and further improvements of the smelting performance are still being carried out.

Jan 1, 2006

By Tiffany Brown

In the thiosulfate gold leaching process, thiosulfate is used to complex gold following electrocatalytic oxidation of the native metal by Cu(II)-ammines. Unfortunately, Cu(II) complexes also catalyse the undesirable conversion of thiosulfate to polythionates. We have been seeking alternatives to ammonia, which fulfil the role of ammonia but minimize thiosulfate decomposition. One aspect of these studies has involved the determination of the rate of thiosulfate oxidation by the Cu(II) complexes from UV-Visible spectral changes. Various ligand classes, including pyridyls, polyamines, aminocarboxylates and picolinates, have been tested and the majority found to inhibit thiosulfate decomposition. Interesting variations in reactivity with the nature and denticity of the ligand and L/M ratio have been observed. In the case of open chain polyamine ligands with 2 to 5 nitrogen donors, the rate of thiosulfate oxidation was generally found to decrease with the denticity and the concentration of each ligand. Saturation of the Cu(II) coordination sphere appears to inhibit the oxidation of thiosulfate when excess thiosulfate is present. The Cu(II) complex of the branched polyamine ligand, tris(2-aminoethyl)amine (tren) exhibits this behaviour in excess thiosulfate. Interestingly, when the [Cu(tren)(OH2)]2+ complex is in excess oxidation of thiosulfate was observed. This unexpected finding prompted a spectrophotometric study of this reaction which has revealed that the oxidation of thiosulfate involves several processes, two of which involve the formation and decay of a tetrathionate radical.

Jan 1, 2003

By Varadajan Seshadri

The increase in production of continuous casting machines requires long ladle sequences without interruption. Very often the production schedule has to accommodate a variety of steel grades. In such cases downgrading may be inevitable. Models must be made available to study the alternatives that would make possible mixing of steels in the tundish but minimizing the losses due to downgrading the slabs. Physical modeling was used to evaluate the influence of variables such as internal geometry of the tundish, presence of turbulence inhibitors, depth of ladle long nozzle, weight of steel in the tundish, steel throughput upon the tundish transition curve. Expressions for minimum residence time and transition period have been determined. Mixing-transition is allowed to continue inside the liquid pool in the mold and the final solute distribution in a given cross section is captured by a solidification model. The result is a map of the transition in the final product.

Jan 1, 2006

By F. Field, R. Kirchain, J. Gregory

Utilizing alternative materials is an important tactic to improve the environmental performanceof products. Currently a growing array of materials candidates confronts today’s product designer. While life-cycle assessment (LCA) methods provide quantitative input into this selection decision, their implementations are evolving and disparate. The goal of this paper is to explore several major analytical variations of LCA implementations and the implications of these variants across a range of application contexts. Specifically, this paper examines analytical variations in valuation method and treatment of recycling by exploring allocation methods that affect product end-of-life. Case studies across a range of materials are presented, including materials that exhibit a spectrum in variation of environmental performance and material degradation between primary and secondary applications. Preliminary results indicate that the choice of analytical method can have real impacts on individual metrics and there are sets of analytical variation over which strategic results are strongly affected.

Jan 1, 2008