Search Documents

By Phillip J. Maddex

After the presentation of a co-authored paper, "The Cost of Transporting Ores and Raw Materials in World Markets", at the February SME meeting, one questioner commented, "You have been talking about the large shipper and ship loads. What does the small shipper do?" This paper will attempt to answer that question, at least in part. Probably the questioner hoped to hear about specific new tools and new techniques that he could apply. But one paper could only scratch the surface of the vast fund of information available; so rather than talk specifics we should take basics, that is, people, management and technology.

Jan 1, 1967

By H. D. Freeman

The Pacific Northwest Laboratory (PNL) is developing cover technology for uranium mill tailings that will inhibit the diffusion of radon to the atmosphere. As part of this cover program, an improved radon flux measurement system has been developed. The radon measurement system is a recirculating, pressure-balanced, flow-through system that uses activated carbon at ambient temperatures to collect the radon. With the system, an area of 0.93 m2 is sampled for periods ranging from 1 to 12 h. The activated carbon is removed from the radon trap and the collected radon is determined by counting the 214Bi daughter product. Development of the system included studies to determine the efficiency of activated carbon, relative calibration measurements and field measurements made during 1980 at the inactive tailings pile in Grand Junction, Colorado. Results of these studies are presented.

Jan 1, 1981

By M. J. Shields

There are numerous suggestions in the literature on methods of obtaining representative samples of waste rock or mill tailings. Some suggested methods would result in thousands of samples and very high costs for a large facility. There is no general rule that can (or should) be followed, such as collection of a given number of samples per mass of material, per acre of impoundment, or per foot of drillcore. Each site is different, and the adequacy of sampling must be tailored to the site. A logical approach is to let the variability at the site dictate the number of samples that should be collected and analyzed, and then to quantify and evaluate the results by means of standard statistical methods.

Jan 1, 1998

By G. L. Schroeder, C. H. Summers, D. B. Lindsay

INTRODUCTION The requirement that is placed on owners and operators of underground mines to protect workers against the health hazard of inhaling radioactive materials which are short-lived decay products of 222Rn can be satisfied by applying a considerable variety of what we may call "engineering" solutions as well as a number of "administrative" remedies to the problem. The most obvious of the "engineering" approaches has always been that of forced ventilation, in which relatively clean (i.e., radon-free) air from aboveground is drawn or pushed through the mine workings by a system of fans and ducts. This relatively clean air, in sweeping through the drifts, stopes and haulageways, dilutes the radon and radon-daughter concentrations in the air of the mine, and performs the added beneficial function of removing the daughter-mixture quickly enought to limit grow-in of the longer-lived nuclides in the group that make up the "toxic trio" on which the Working Level (IM) unit is based. Effective as the dilution-ventilation method is for control of WL in most underground mining situations, however, the increasing strictness of control measures that have been imposed on the mining industry over the last two decades have demanded measures of even greater effectiveness. In times of poor markets for yellow-cake and other products of the mines, mine operators are pressed to reduce operating costs, and the installation of additional primary ventilation capacity can be a severe burden on a mine that is already laboring under an unfavorable earning power. When traditional dilution-ventilation systems alone cannot meet the requirement for WI, control, radiation safety engineers and ventilation engineers begin to look at alternatives and auxiliary methods. Since the radon which produces the toxic daughter products originates in the rock of the mine walls, and since, in most United States mines, that rock is a porous sandstone through which air can move under the effect of atmospheric pressure gradients, and through which radon can diffuse relatively freely, one way to help control the growth of WL would be to hinder the escape of radon from that reservior of porous rock. An appealing; method for hindering that natural flux of radon-polluted air from the walls of the mine has long been apparent; namely, to apply a low-permeability coating over the surface of the rock, thus sealing the radon in place and, in theory at least, preventing its escape into the mine air. Our 1970 report to the U.S. Federal Radiation Council on the subject of cost impacts of proposed changes in the occupational standards for exposure of underground uranium miners to airborne radon daughters noted the possibility of using polymeric wall sealants as a means of controlling radon-pollution of mine air. Since that time a number of reports have appeared in the technical literature advocating this technique for restraining the escape of radon from building materials, mill tailings, and other materials containing 226Ra, in addition to the surfaces of underground mine workings. During this period, some controversy has occurred over the question of the probable effectiveness of wall sealants in limiting the escape of radon from the rock. Our 1970 report speculated that flaws (cracks and "pinholes") in the coating might be all but unavoidable in practice, and that even a conservative estimate of the frequency of such flaws would lead to a prediction of ineffectiveness. Hammon et al, in a laboratory evaluation of radon sealants conducted by Lawrence Livermore Laboratory of the University of California in 1975 on behalf of U.S. Bureau of Mines, concluded that a wide variety of polymeric coatings would provide "nearly 100% effectiveness" in restrain¬ing escape of radon from mine wall surfaces if applied in "thicknesses between 5 and 10 mil" (125-250 [y]pm). John Franklin and co-workers at the U.S. Bureau of Mines laboratories in Spokane, Washington, have carried the experiments with polymeric sealants through additional laboratory tests and into actual mine environments, reporting that selected sealants could provide attenuation of radon flux by a factor of four (75-80% reduction). Robert Bates and John Edwards of USBM developed a computer-assisted mathematical/physical model that predicts a relatively small effect of flaws in a low-permeability coating on the radon flux from a sandstone-type matrix. FIELD TEST Since all actual experimental work with wall sealants showed some beneficial effect on radon attenuation (even if not as exciting as the "nearly 100%" predicted by Hammon), USBM was encouraged to extend its evaluation to an actual operating uranium mine, and awarded a contract for that work to Arthur D. Little, Inc. in September 1979. We were fortunate in obtaining the voluntary cooperation of Atlas Minerals Division of Atlas Corp., who operate a mill and several underground mines in and around Moab, Utah. Atlas made available for our use a small T-shaped drift in their Pandora Mine in LaSal, Utah, and provided space for instrumentation and recordkeeping by our field crew in a surface building near the mine entry. Atlas also provided electricity and water to the test site, together with assistance in establishing necessary ventilation, removing rubble from the site, conducting periodic WL surveys and furnishing auxiliary man-power for the heavy hard work of coating the walls with gunite prior to application of the polymeric sealant. The generous coopera-

Jan 1, 1981

The minerals industry contributes to the economic growth, prosperity and quality of life of nations, particularly in areas where there might be limited opportunities for employment in other sectors. However, notwithstanding their economic importance, the minerals extraction and processing industries are considered to have significant impacts on the surrounding environment. In recent years many mines have implemented modern monitoring technology and modelling of the monitored environmental parameters to provide scientifically proven indicators about the state of the environment. The flexibility required by the minerals industry to respond dynamically to a changing natural, social and economic environment has become a major consideration. Whilst the notion of continuous improvement is embodied within most environmental management systems, what is now required is a structured audit trail which tracks the flow of resources through the production process to the ultimate environmental impact associated with their consumption, transformation and disposal. Imperial College is coordinating an EC funded project, which is developing a methodology to minimise the ?full life-cycle? impact of metalliferous mining projects, adopting an integrated approach to production and process design, and the costs involved. In order to develop a life cycle assessment (LCA) system that will incorporate different types of data related to the minerals extraction operations, a data inventory was designed and coded in an object-relational database model. The calculation procedures accounting for the input/output balance of the alternative scenarios for mining production, processing, waste disposal, monitoring, and their financial implications are being programmed into a software system. This paper presents the rational and innovative aspects of this work. The methodology developed for the life cycle database is illustrated for the mining production and gaseous emissions components of the system.

Jan 1, 2003

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their coal. Sulfur was the major concern, with BTU and sodium limiting the market for some. The Clean Air Act has extended the PRB market into plants converting from other coals. These new customers are more sensitive to constituents affecting boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to control cost more stringently than ever. Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998

By Kerstin Malmqvist

Simulation technique has been used for a feasibility study of a deep exploration project for massive, sulphides in an old mining district, the Skellefte field. An interactive computerized mathematical model of an ore field and a drilling procedure has been constructed. It is possible to represent varying geological structures. The model also takes in consideration economical factors such as drilling costs and ore values. On this model Monte Carlo simulations and probability calculations are done in order to estimate the outcome of different drilling strategies under varying geological assumptions. Under the specific conditions of the well known Skellefte field, it is found to be possible to even calibrate the mathematical model.

Jan 1, 1979

By K. L. Whitehead, R. A. Jankowski, N. I. Jayaraman

Most continuous miner sections utilizing flooded-bed scrubbers also use blowing face ventilation. Blowing ventilation, however, interferes with dust capture and minimizes scrubber effectiveness. To enhance the efficiency of the scrubber system and reduce dust concentrations, the Bureau of Mines tested various combinations of operating parameters. Experiments for system efficiency took place in a full- scale model mine at 3.05 m roof height. In general, higher values for scrubber and face airflows resulted in lower dust concentrations. In addition, optimum dust controls would include a face ventilation to scrubber airflow ratio of one. When the airflow ratio was either less than or greater than one, the dust levels in the return and at the operator locations increased. No single dust control technique was the most effective one at all locations due to mutual interaction among techniques.

Jan 1, 1992

By S. J. Stokowski

An extensive drilling and laboratory testing program indicates that diagenetic dolomitization of the Oligocene Sombrerito Fm. limestone, southwestern Dominican Republic, is detrimental to the usefulness and quality of the potential construction aggregate resource. The first part of this program was the collection, photographing, and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I (youngest) approximately 10 m of white, dense marine limestone; II, approximately 5 m of white, interbedded dense and chalky marine limestone; III, 2+ m of tan, chalky calcitic dolomite. Unit I has been often altered by lateritic weathering and/or dolomitization; Unit II is often altered by dolomitization. The quarry layers were individually crushed, by core, into coarse aggregate sizes for chemical and physical (specific gravity absorption, MgSO4 soundness, sand equivalent, and LA degradation) analyses. The non-weathered units decrease in coarse-aggregate yield and quality with depth and dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value, an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average 5-cycle MgSO4 soundness by about 17%.

Jan 1, 1987

By Paul E. Senseny

Data from triaxial compression tests per- formed at confining pressures between 0 and 100 MPa are used to evaluate parameters in a contitutive model that is based on microcracking. The tensorial formulation is reduced to equations that are specific to the simple Loading imposed in triaxial compression tests. Procedures for evaluating the model parameters are described, dependence of parameter values on confining pressure is discussed, and prediction of failure is assessed.

Jan 1, 1986

By Roy E. Williams, Muriel S. Robinette

Ground-water contamination from uranium operations could be avoided with proper site analysis techniques. Contamination from tailings disposal sites is carried downgradient within permeable hydrostratigraphic units which can be located and delineated with a combination of drill holes and borehole geophysical logs. Engineering safeguards can be designed into a disposal site by determining if permeable hydrostratigraphic units exist which will dominate the flow system and provide seepage paths for contaminates. It is more cost-effective to accurately assess seepage potential with geophysical logs before contamination becomes a problem than to be faced with a major clean-up effort after contamination has occurred. If a uranium waste impoundment already has a ground-water contamination problem, then borehole geophysical logs may be used to delineate the contaminated zones which need to be cleaned up. It is less expensive to withdraw the contaminated plume from only within the affected zones rather than attempt to dewater the entire area. Consequently, the geophysical logs are invaluable in assessing which zones should be pumped and where packers should be set for construction of piezometers to allow monitoring of water-quality changes. A surface geophysical technique is being tested and developed for monitoring of seepage frum uranium tailings impoundments. Geoelectric soundings and profiles from direct current resistivity surveys can locate anomalous areas for the placement of drill holes to better assess seepage. This reconnaissance technique should eliminate random hit-or-miss drilling at sites where monitoring is required. Tests and experiments are being done on developing the capabilities of this technique to incorporate complex resistivity data to assess cultural impedence noise which complicates simple resistivity data.

Jan 1, 1980

By Joseph C. Rota, Charles E. Ekburg

Introduction The Gold Quarry gold deposit is the largest bulk tonnage epithermal gold deposit in northeastern Nevada to be developed by Newmont Gold Co., formerly known as Carlin Gold Mining Co. Exploration and development of the deposit extended over a period of nearly 50 years before bulk tonnage mining became economically feasible. Proven reserves at Gold Quarry are currently estimated at more than 255 t (8.2 million oz.) of gold, accounting for more than 40% of the total Carlin Trend mineable reserves for 1986. Milling began in late 1985; dump leaching of lower grade ores began in May of 1986. The mill has exceeded the initial design throughput rate of 6.3 kt/d (7000 stpd) and is now processing more than 8 kt/d (9000 stpd). The dump leach facility will process more than 7.3 Mt (8.1 million st) of lower grade ores in 1986. The Gold Quarry ore body is to be developed by an open pit that will eventually be 1830 m (6000 ft) long, 1220 m (4000 ft) wide and 300 m (1000 ft) deep. The mine currently produces 77 kt/d (85,000 stpd) on a 24-hour-a-day, seven-day workweek. Planned pit production will increase to nearly 168 kt/d (185,000 stpd) in 1988. Production equipment currently includes one Demag H-/285, three Komatsu PC-1500 hydraulic shovels, two Cat 992C loaders and 21 90 to 135 t (100 to 150 st) haul trucks. Mining is conducted on 8 m (20 ft) benches within the Paleozoic

Jan 4, 1988

By J. W. Wilson, Y. P. Wang, M. H. Erten

The use of water is still the most effective and economical means for dust control in underground coal mines today along with dilution by the ventilation current. Studies have shown that the dust capturing capacity of water is a result of a balance of many intermolecular forces. Surfactants are known to reduce such forces by affecting both the surface tension of the liquid and its interfacial tension against a solid. Surfactants can be added to the water sprays to facilitate the dust capturing capacity. A laboratory scale model has been developed in which surfactants were added to the spraying water and preliminary data indicates positive results.

Jan 1, 1991

A general form of pore pressure in a saturated porous medium, which is subject to external forces it has the pressurization of a borehole in hydraulic fracturing, is derived. The pore pressure consists of two parts: the preexisting initial pore pressure and the pressure induced by fluid flow due to the pressure difference caused by pressurizing the borehole The initial pore pressure associates with the effective stresses in the stress, fields of crustal stresses and a thick hollow cylinder subjected to internal and external pressures. The pure pressure weaned by fluid flow is implied in Biot's (1941) constitutive equation for three-dimensional consolidation and proved to be the exact effective pore pressure (Nur and Byerlee, 1971). Using this general form of pore pressure, a general poroelastic model for hydraulic-fracturing breakdown (fracture-initiation) pressure was derived. This model was validated by laboratory experimental results on Indiana limestone. Three sets of tests were conducted under the conditions of preexisting pore pressures of 6, 21 and 28 MPa, respectively. The equal horizontal (confining) pressures applied in the tests ranged from 6 to 60 MPa. Hainison and Fairhurst's (1967) model appear to be applicable to rocks having microcracks or flows. Experimental results of fracture reopening pressures on Indiana limestone supported this assertion. The test results also demonstrated that, when the pressure difference between the confining and the initial pore pressure grows larger than 14 to 21 MPa, the breakdown pressures agree well with the general poroelastic model developed in this paper. This indicates that the developed model will be superior when hydrofacturing stress measurements are conducted at great depth.

Jan 1, 1997

By Richard Meriwether Smith

Mining-related earthy bodies in contact with the atmosphere are now counted, generally, as minesoils. Because soils within this broad category are extremely young the influence of parent material is stronger than in older soils, where climate, organisms, and topography have had time to interact with near-surface rocks to form more distinctly differentiated profiles. Understanding of minesoil properties and processes is aided by definitions of rock types in terms of chemical, physical, and mineralogical characteristics that are, with some degree of consistency, translatable into soils. Geological correlations based on age or sedimentary sequences are helpful if they assure details of mineralogy and lithology, but our pedologic objectives demand that any conflicts involving rock types must be resolved in favor of distinctions having strongest implications for soil properties after mining. Chemically this approach emphasizes accounting of potential acid-base status, plant nutrient availability by adapted and calibrated extraction procedures, and absence of biotoxins. Physically it anticipates particle sizes, shapes, and arrangements in readily pervious soil profiles that will favor plant growth with desired levels of moisture and oxygen. Concurrently we are considering soil property suitability for uses other than growth of plants. Above all we need to be able to predict pedogenic processes in the particular environment, including rate as well as direction of chemical and physical change.

Jan 1, 1974

By P. K. Davis

The results of a previous basic study of the flow and design characteristics of the hydrocyclone has shown that a recovery as high as 99% with a product rating of 0.95 can be achieved on a "batch?2 basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-cyclone system was also sponsored by the U.S. Department of Energy. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1989

By L. J. Laughlin

The majority of non-drive conveyor pulleys use rotating shafts, and typical idler rolls use non-rotating shafts, even though both products are used to support and guide the conveyor belt and its load. This paper will explore and compare the requirements for rotating and non-rotating shaft designs and the impact of that design on the product. Additionally, it will explore how the “roller” bearing types (deep groove ball, tapered, or spherical) affect these designs.

Jan 1, 2003

By V. Vesselinov, S. Orr

"Enhanced heap leaching - Part 1: Insights" (Orr, 2002), different flow and transport phenomena that could significantly reduce leaching recovery were investigated. The combination of such understanding with advanced flow and transport modeling establishes the link between cause and effect, thereby, directing operators to optimal design and construction of new heaps. Modeling of flow and transport in heaps could also point to a unique change in application method or rate that would maximize leaching enhancement of an existing heap under existing situation and leaching history. The use of such a model is cost effective in that it can simulate multiple scenarios of alternative leaching enhancement methods. By simulating a large number of irrigation scenarios, such a model can point to the optimal and/or the most promising alternatives for a particular heap. The authors' simulations concentrate on the effects of changes in application rates and heap design on changes in flow paths and enhanced leaching recovery. Based on such simulations, an intelligent control agent, such as Multiple Resolution Decision-Support System (MRDS) (Meystel and Albus, 2002), could build a new representation of the complex heap-leaching system. And, by learning from historical data and current information, it could provide optimal management of heap leaching and heap decommissioning.

Jan 1, 2003

By D. W. Park

The Longwall Strata-Control and Maintenance System (LoSCo-MS) is a software and data-communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and the forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels, including excessive shield load, low setting pressure, leg leakage, poor shield performance and imminent maintenance problems. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, the next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems in their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 2000

By Roy L. Klein

The production of synthetic fuels from coal has been pioneered by South Africa. South Africa made a decision in 1975, due to the threat of an oil embargo, to proceed with the construction of Sasol Two, then followed by Sasol Three. South Africa has large coal but little indigenous petroleum reserves. The indirect coal liquefaction process used by Sasol since 1955 is the only commercially demonstrated method available for producing transport fuels from coal. The new plants consume 27 million tons per year of coal from a single mine that now produces transport fuels in sufficient quantities for energy independence.

Jan 1, 1983