Search Documents

By B. Ni, J. D. Robertson

A new radioactive tracer method for the measurement of airflow in inaccessible airways was developed. The method can be used in situations where studies of the mine-ventilation system are not possible using conventional flowmeters (anemometers). The method was tested in the ventilation laboratory at the University of Kentucky and in the US Bureau of Mines Experimental Underground Coal Mine and was utilized in leakage, dilution and flow-velocity measurements.

Jan 1, 1998

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and a cooperating longwall trona mine in the Green River basin of Wyoming in the United States. The objective of the study was to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. Tracer gas experiments using sulfur hexafluoride (SF6  ) were conducted to describe air movement on the face and in the mined portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of gases emitted from the face and caved gob.

By Isabel F. Barton, Christian A. Rathkopf, Mark D. Barton

Rhenium (Re) is one of the rarest elements on earth and is a designated critical element in the United States and European Union for its uses in superalloys. Unusually among critical elements, Re is produced entirely as a byproduct of molybdenite (MoS2) mining, as pure Re minerals are extremely rare. However, Re concentration in natural molybdenites varies from a few parts per trillion to tens of percent. There are few known consistent patterns and no firmly established reason for this variation, making it difficult to use molybdenite Re content as a proxy for metal grades, a vector to high grades, a clue to the geological and geochemical nature of the ore deposit, a guide to overall Re resources or for any other of the applications that have been suggested for it over time. 

By K. K. Cheng, Z. M. Chen, A. L. Mular

INTRODUCTION Since the nineteen fifties, process engineers have been seriously concerned with process models for various purposes (1,2,3). Models serve as subroutines to mathematical flowsheets which simulate circuits of interest. Simulators can serve to increase process know- ledge, assess circuit performance, investigate flowsheet modifications, evaluate new flowsheets, perform off-line optimization, and compare alternative control strategies. This chapter describes a methodology to develop a simulator of a bulk Cu-Mo circuit comprised of roughers, scavengers and 3 stages of cleaning. The simulator was employed to evaluate the influence of water addition at circuit points and to estimate the optimal number of cells for each stage in the circuit. DESCRIPTION OF CIRCUIT Figure 1 is a flowsheet of the Brenda Mines Ltd. (located near Peachland, B. C.) bulk Cu-Mo flotation circuit as simulated prior to an expansion/renovation which involved the installation of large, new flotation cells. Referring to the flowsheet, feed to rougher cells includes fresh feed, scavenger concentrate and 1st cleaner tailing. Rougher con, 1st cleaner (sect ion 2) con and 2nd cleaner tailing are fed to 1st cleaners (section 1). 1st cleaner (section 1) concentrate and 3rd cleaner tailing serve as 2nd cleaner feed, while 2nd cleaner concentrate is fed to the 3rd cleaners which produce a final bulk concentrate. Table 1 lists cell types and specifications important to the circuit. DEVELOPMENT OF MODELS To develop flotation cell models a systematic procedure was employed (4). This involves the selection of responses and factors, proposing models to be fitted, the acquisition of raw data, the statistical adjustment of raw data, fitting models to adjusted data and testing the adequacy of fitted functions. Responses and Factors Responses of interest included recoveries, concentrate grades and concentrate solids/water flow rates for each stage. Factors that influence these responses, such as reagent addition rates, air flow rates to cells, solids and water flow rates to stages and feed grades were not manipulated during the sampling period. Thus, the investigation was limited,

Jan 1, 1986

By T. Ruff, J. Steele

The lack of visibility near earthmoving equipment results in an average of five fatalities in U.S. surface mines each year. These accidents occur when a piece of equipment either strikes another vehicle or worker, or travels over the edge of an embankment. Researchers at the National Institute for Occupational Safety and Health have evaluated off-the-shelf proximity warning systems that sense obstacles near the equipment and provide an alarm to the operator. Limitations of existing systems have necessitated the development of new systems designed specifically for mining equipment, including a GPS-based proximity warning system and a computer-assisted stereovision system.

Jan 1, 2004

By H. Kempton

New methods for remediating metals-contaminated groundwater include in-situ emplacement of highly adsorptive substrates to permanently retard solutes. Substrates are introduced by sequential injection of soluble components that precipitate in the aquifer, forming a permanent high-retardation zone. This method overcomes the factors that limit pump-and-treat remediation; i.e, long-term source loading and slow desorption. Column tests demonstrated efficient substrate emplacement, increasing retardation coefficients of Cr(VI) by 20 and As(V) by 40. Similar effectiveness is expected for other heavy metals. Simulations using a coupled advective-geochemical model accurately matched substrate emplacement and arsenic attenuation, allowing extrapolation to other constituents and larger-scale applications.

Jan 1, 1999

By D. R. Nagaraj

The chemistry and structure-activity relationships for four new classes of sulfide mineral and precious metals collectors developed recently are discussed in this paper. These collector classes are alkoxycarbonyl alkyl thionocarbamates and thioureas, dialkyl (or diaryl) monothiophosphates and dialkyl monothiophosphinates. The main emphasis will be to highlight the differences between collectors and their affinities for various minerals on the basis of data on kinetics of adsorption on pure minerals, natural ore flotation and microscopy of flotation concentrates. The mechanism of interaction of these collectors with sulfide minerals is also discussed with the available data on the FTIR and solution chemistry studies.

Jan 1, 1989

By Leandro Augusto Viana Teixeira, Angela Avelar, Ruberlan Gomes Silva, Virginia S. T. Ciminelli, Daniel Majuste

Rare earth elements are essential for modern life products and green technologies. Recent supply constraints have boosted the development of rare earth projects after the price peak of 2011. The feasibility of a project depends on the definition of a processing route, which in turn depends primarily on the rare earth mineral, with monazite and bastnaesite representing the two most relevant minerals. Monazite-type ores usually contain high acid consumption impurities, such as iron, aluminum, calcium, magnesium and phosphates, and may also contain prohibitive levels of radioactive thorium in its composition. Based on thermodynamic analysis, the present work discusses the fundamentals of a selective process route for rare earth extraction from monazite ores with high iron content. This process involves sulfation by means of concentrated sulfuric acid and roasting at a high temperature. The route yields high rare earth extraction with low iron and thorium extraction and low acid consumption. Rare earth extractions as high as 80 percent were achieved, while iron and thorium extractions were lower than 1 percent, and acid consumption was lower than 0.34 kg of sulfuric acid per kg of ore. The operational window was compared to the one predicted by thermodynamic modeling, with 700 °C representing the optimal roasting temperature.

By W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

?Energy-related systems: wind, solar, electric are typically materials intensive. As new technologies are widely deployed, significant quantities of the elements required to manufacture them will be needed. However, many of these unfamiliar elements are not presently mined, refined or traded in large quantities, and, as a result, their availability might be constrained by many complex factors. A shortage of these ?energy-critical elements? could significantly inhibit the adoption of otherwise game-changing energy technologies. This, in turn, would limit the competitiveness of the U.S. industries and the domestic scientific enterprises and, eventually, diminish the quality of life in the US.? -Energy Critical Elements: Securing Materials for Emerging Technologies?- American Physical Society, 2011.

Jan 1, 2012

By Robert W. Bartlett

Pretreatment of sulfidic refractory gold ore by biooxidation in coarse-crushed ore heaps is a promising new technology, especially for low-grade ores that cannot afford pressure leaching or roasting. An algebraic equation for determining the economically optimum biooxidation of the sulfide minerals in the ore is provided that is based on the empirical biooxidation rate constant for the ore, the project's financial discount rate, the ore grades of both refractory and non-refractory gold, and the gold price. Then, the economically optimum duration of bioheap pretreatment, t$, is determined from its logarithmic relation to the optimum fractional extent of ore biooxidation, F$, through the ore's biooxidation rate constant. In doing so, it is assumed that the ore is adequately crushed and amenable to bioheap pretreatment and that the cumulative oxidation of the ore with time is known from ore testing so that the rate constant can be determined.

Jan 1, 1995

By Rod A. Levander, Kenneth B. King

INTRODUCTION The Panna Maria Uranium Project is located in South Texas, between San Antonio and Corpus Cristi, approximately 10 kilometers (6 miles) north of Karnes City, Texas. The tailings disposal facilities are located immediately south of the mill area and the central portion of the west pit. The mine and mill drainage pond is located north of the tailings pond. Location of the facilities is shown in Figure 1. The tailings pond is a disposal area for mill process wastes and has a capacity for storage of approximately 9 million metric tons (10 million tons) of tailings. This capacity is adequate for approximately 10 years of milling at a maximum rate of 2,700 metric tons (3,000 tons) per day. The tailings disposal facilities were designed to essentially eliminate discharge of contaminated waters to preclude degradation of surface streams or ground water. Water levels in the ponds will be maintained. through reuse in the mill and by evaporation. WASTE CHARACTERISTICS The sources of waste that is stored in the tailings pond include runoff from the mill area and tailings from the mill processing. The tailings consist of a sand slime slurry; the percentage passing the No. 200 sieve varies depending on the ore material, and it is generally in the range of 10 to 25 percent. The tailings have a density of approximately 1.2 metric tons per cu m (75 lb per cu ft) and an average specific gravity of 2.55. The liquid effluent from the mill consists of waste solutions from the grinding, leaching, extraction, and washing circuits of the mill. These solutions have an initial pH of 1.5 to 2.0 and contain the remnants of the leaching agents used in the mill process, sulfates, some silica as the primary dissolved solid, and trace quantities of soluble metals. This liquid is discharged with the solids into the tailings pond and is diluted by rainfall and runoff from the tailings dam. Runoff from the mill area, drainage from the mine area, and de-oiled water from truck washing facilities is discharged into the mine and mill drainage pond. Runoff from the mill area drains approximately 28 hectares (70 acres) from offices, shops, the mill site, the ore pad, haul roads, and adjacent areas. Mine drainage is collected in the mine area and pumped to the mine and mill drainage pond.

Jan 1, 1980

By Xinming Lu

In this paper, we use a new kind of fan charateristic curve instead of the common quadratic function, and give the existence and the uniqueness of the solutions to the ventilation network controlling equations, so that the existence and the uniqueness of the solutions for the natural air distributting problem can be conveniently given. We also give a conjugate gradient method with the global convergence to solve the equations having the unique solution. Because we adopt a very efficient technique of one dimensional search (or linear search) in this method, the method can quickly solve a lot of problems, especially in large scale problems. The second part of this paper is the establishment of the model of the constrained quadratic programming for the measurement adjustment of mine ventilation network. We give the algorithm to solve this model as well. The two algorithms given above have been realized in the mic-computer MC-68000 with Fortran codes, and the numerical results are satisfactory.

Jan 1, 1991

By Warren D. MacEvoy

INTRODUCTION Good ventilation bulkheads (stoppings) can be obtained only by conscientiously adhering to four basic principles: carefully selecting the site for the bulkhead, adequately preparing the site, properly constructing and sealing the bulkhead, and checking the results with a smoke tube before leaving the area. If all these guidelines are followed during each ventilation project, a poor job will result only from the use of improper materials and cannot be blamed on carelessness or oversight. SITE SELECTION A perfectly constructed bulkhead in the wrong location can be completely worthless. Conceivably, a bulk-head in the wrong location could cause dangerous ventilation conditions that are difficult to identify and isolate. If the suggestions herein are followed, a considerable amount of work, time, and material may be saved. Perhaps the single most important step is always to select the exact site for a bulkhead before starting construction. Although the latitude in selecting a site may be limited by instructions or operating conditions, it is common to find poor bulkheads built within a few meters (feet) of a site that would have been far superior but was overlooked during the planning process. The ideal site for a bulkhead should have as many of the following features and conditions as possible: 1) To provide a solid bulkhead, the selected site should be in firm and unbroken ground. 2) To minimize the amount of work and material required and to minimize the danger of later damage to the bulkhead, the site should have as small a cross section as possible. 3) The bulkhead site should not be encumbered by interferences such as pipes, wires, ditches, wire roof supports, trash, muck piles, etc. 4) The walls and timbers of the site should be free from oil, grease, or tar that would inhibit adhesion of the sealant used on the bulkhead. 5) Unless special precautions are taken, the site should not have water seepage, standing water on the floor, or water-carrying ditches. 6) To expedite construction of the bulkhead, the site should have reasonable access to transportation, supplies, communication facilities, and compressed-air lines. 7) The site should have a reasonably level floor, allowing direction of the bulkhead door swing to be reversed at a later time if so desired. In a steeply sloping location, it may be possible to open the door in one direction only. SITE PREPARATION Once a suitable site has been selected for the bulk¬head, it must be prepared properly. All site preparation work should be completed before starting any construction work on the stopping itself. Unfavorable site conditions can be identified during the course of thepreliminary site preparation, saving time, effort, and materials that otherwise might be wasted. The follow¬ing preparation steps help assure the construction of a good stopping: 1) If wire mesh has been used at the site, a strip 457 mm (18 in.) wide should be cut and removed from the walls and roof at the selected location. 2) The exposed strip of rock should be barred down thoroughly to provide a smooth surface. 3) All obstructing materials should be removed, including old timbers, pipes, rockbolts, wires, etc. If a conduit must cross the bulkhead area, it should be located or relocated away from the floor, walls, and roof to allow a 6.28-rad (360°) seal around the juncture between the conduit and the bulkhead structure. 4) All loose muck should be cleaned from the site and a trench about 152 mm (6 in.) deep should be dug from wall to wall in the floor. The trench must be wide enough to accommodate the entire bulkhead, including the posts. 5) The rock surfaces of the walls and roof should be cleaned with a wire brush to remove as much loose surface material as possible. Thorough cleaning promotes adhesion of the bulkhead sealant to the surfaces of the walls and roof, thus promoting an airtight seal. 6) It is quite difficult to seal landing mats that cross a bulkhead. If such a crossing cannot be avoided, the bulkhead should be placed between the end and the first hole in the steel so at least one side of the bulk-head can be sealed easily and completely. That may have to be done prior to actual construction if the end is located on the opposite face from the seal coating of the bulkhead. BULKHEAD CONSTRUCTION The three principal considerations in bulkhead con¬struction are the type of bulkhead, materials to be used, and construction method to be employed. For many projects, the bulkheads are specified by the requesting agency, with no latitude for independent choice of the type, materials, or construction method. In such cases, any deviations from the specifications, for any reason, must be approved in advance by the proper department or by the project senior ventilation engineer. Types and Materials When a choice of type, materials, or method is allowed, consideration should be given to factors such as cost, required useful life, proximity to blasting concus¬sions, availability of materials, direction of permissible air leakage, and degree of airtightness required. Other factors to be considered include the amount of time available, accessibility of transportation, potential for interference with operations or production, ambient water conditions, availability of connections to com¬pressed-air lines, etc. Despite the multitude of factors to be considered, most stoppings can be analyzed easily and the proper choices can be made without much difficulty. The four common classes of bulkheads utilized in

Jan 1, 1982

By Ruifeng Li, Yanghui Ren, Hua Gao

"Since entering the new century, China’s coal industry has witnessed the rapid development, and provided a reliable energy supply for the national economic and social development. But after the “golden decade” of rapid development, the coal industry now is facing overcapacity, low industrial concentration and production efficiency, high pressure of production safety and environmental protection and other prominent issues. Based on defining the connotation of highly-efficient recovery of coal resources, this paper established the relevant 8 indicators to reflect the highly-efficient recovery level of coal resources, summarized the present situation of China's coal resources recovery and the main problems, analyzed the development environment of China's coal industry under the new situation, and finally put forward the strategic measures to promote highly-efficient recovery of coal resources in China.1. Background Coal is the main energy in China. Since entering the new century, China's coal industry has made significant progress, and the level of production safety, resource recovery rate and mining mechanization increased significantly, which provided a reliable energy supply for the rapid development of the national economy. However, due to the changes of China's economic environment, slow growth of energy demand and other factors, some prominent contradictions in the coal industry have significantly restricted the healthy development of the industry. The first problem is serious overcapacity. In the past few years, 16 industries including coal, electric power, chemical and others have invested in coal mines. It is reported (Han 2016) that only during the nine years from 2005 to 2014, the fixed assets of coal industry increased totally more than 3.3 trillion RMB, which brought a large number of production capacity. Affected by the slowdown of economic growth and energy structure adjustment, Chinese coal demand has reached the peak platform and caused the overcapacity of coal supply, so shutting down the backward capacity is the most important task in the future. The second problem is the low efficiency of coal production. There are about 4.3 million coal mine workers in China, and the annual coal production per capita is less than 900 tons, while it was reported (EIA 2016) that the annual production per capita in the United States is more than 10 thousand tons. The third problem is that the green coal resources are not rich. Among the 1.53 trillion tons proven reserves, only about one third are green coal resources in accordance with the principle of ""safety, technology, environment and economy"". The coal resources with high quality and easily mining conditions are not abundant."

Jan 1, 2017

By Harry C. Oussoren, James C. Miles

A new seven kilometer long subway line is being constructed through dense glacial soils under a major thoroughfare in Toronto. Eductor, deep well and vacuum wellpoint systems are being used to lower the water levels by as much as 16 metres for the construction of the twin tunnels and associated structures. The design and performance of the dewatering systems will be described. Unanticipated difficulties and their solution will be presented.

Jan 1, 1999

By Peter H. Grimley

It is important to realize that lending institutions have a very different risk-profile from that of an equity investor. For bank financing, a feasibility study must address the concerns of the lender and these can be summarized under the four 'PI Is: Project, Performance, Product and People. Generally, feasibility studies focus on the measurable project risks associated with a new venture, but frequently insufficient emphasis is placed on key risk areas such as ore grade and metallurgical recovery. Before accepting full or even partial non-recourse risk, financial institutions will demand evidence that the project was constructed according to specifications and within budget and that its Performance within agreed limits has been demonstrated. Product risk should be discussed in detail in any feasibility study. For industrial minerals, penetration of the market can be critical to success and for commodities with volatile prices, the sensitivity of the cash flow to a range of prices should be carried out. Methods of reducing price risk such as long term contracts or, in the case of gold, forward selling should be carefully evaluated. The People risk is rarely discussed in feasibility studies, but can be a key element. Few projects turn out to be faithful copies of the study and the ability of the operator to identify

Jan 1, 1988

By Nasser Madani, SULTAN ABULKHAIR

The geological and geostatistical modeling of mineral deposits requires densely sampled drillholes that provide accurate and reliable hard data. Furthermore, quantifying orebody uncertainty through geostatistical simulation can allow mining engineers to assess long-term risk in mine planning. Nevertheless, ore deposits can sometimes lack dense drillhole information, reliable hard data with proper quality assurance/quality control (QA/QC), or sometimes both. This study is based on a coal mine located in the Republic of Kazakhstan, where an iron dataset is based on data from three newly drilled drillholes, and geological information comes from a massive collection of legacy drillhole data with no evidence of proper QA/QC. For this reason, a workflow was introduced to construct a representative training image from legacy data and stochastically model geological domains within these three drillholes using a multiple-point geostatistics technique. Once the geological model was obtained, a two-point geostatistics algorithm was applied to model the iron inside each geological domain. The direct sampling algorithm was chosen for modeling geological domains, and sequential Gaussian simulation for iron grade calculation. Both methods were extensively evaluated using different statistical tools and analyses.

Aug 1, 2022

By Mirza Muhammad Zaid, Nana A. Amoah, Ping Chang, Guang Xu, Ashish R. Kumar

The key takeaway of this study is the significant improvement in dust protection for roof bolter operators in underground coal mines. The optimized canopy air curtain (CAC), with a redesigned two-level manifold system, provides uniform airflow distribution that effectively reduces dust exposure. By enhancing the protection of operators from harmful respirable coal and silica dust, this technology can reduce the risk of diseases such as coal workers’ pneumoconiosis (CWP) and silicosis. The application of this optimized CAC design in real-life coal mining operations can dramatically improve worker health and safety by minimizing dust-related exposure, ensuring compliance with industry regulations and prolonging the lifespan of mining equipment by reducing dust accumulation.

Dec 1, 2024

By F. Mauviel, J. Bernard, G. Herrouin, J. P. Lenoble, C. Charles, B. Taine

Manganese nodule projects were quite fashionable during the 1970s. At the beginning of the 1980s, low metal prices led to an almost complete reduction of such activities; however, the Law of the Sea incited the countries that signed it to build a strategy for this ocean resource. Gemonod was created in France in 1984 with a four-year mission. This paper presents the results of its program devoted to the technical and economic studies of nodule exploitation. A commercial mining system is presented. The nodules would be collected by a self-propelled miner and lifted hydraulically through a rigid pipestring. A complete optimized scenario has been built taking into account offshore mining, ore transfer at sea, transportation and processing to analyze the profitability of the project. Considering an average conservative basis for metal prices, after a deep analysis of the market, the return rate of investment of the project appears fairly interesting. These results are new and are explained in comparison with previous foreign studies. These results must not hide the innovative nature of the project nor the associated risks. This is why a mining pilot is required and has been specified by Gemonod.

Jan 1, 1991