Search Documents

By Wei Wu

A computer-aided method for optimization of bench blast design in surface mines is presented. The design procedures basically consist of two steps. Firstly, a series of normalized, full- scale bench crater tests must be carried out in the field to find the optimum burden that produces the largest amount of acceptable fragments and other parameters that defines the effective fracture zone. Next, the locations and initiation sequence of blast-holes will be determined in such a way that each hole, at its time of firing, will be responsible for same amount of burden rock and will be in a position favorable to effective fracture of burden rock. A computer software "B.B." which can assist the second step of the design is fully introduced and its application is illustrated by an example.

Jan 1, 1992

By D. Belin

Treatment of dilute acid mine drainage and similarly polluted water is becoming increasingly complicated. The pressure of economics is now exacerbated by legislation which classifies as hazardous waste the precipitates from conventional lime treatment plants. Since acid mine drainage invariably contains sulfate ions, one solution is to use anaerobic Desulfovibrio type bacteria to reduce the sulfate into sulphide ions which could then be used to precipitate out the heavy metals. Results are presented for both batch flask cultures and continuous column tests. Compost was used as the bacterial substrate in the column test which simulated heaps. Conditions changed from aerobic to the required anaerobic deep in the columns. Polluted feeds (up to 700 mg/l zinc) gave effluent containing well below I mg/l zinc over extended periods. Direct transfer of sulphide ions through a stream from an isolated container of bacteria is a good alternative.

Jan 1, 1991

By P. Huttagosol

The use of computer models to design ultimate pit limits during feasibility study and long range mine planning is becoming a significant practice in open pit mining. One of the problems in determining optimal ultimate pit limits using true optimization techniques has been they require a great deal of computer memory and execution time. In this paper, the maximum closure of a graph, which is a true optimizing model developed by Lerchs and Grossmann, is modified for solving ultimate pit limit problems. By using some properties of the original L&G graph algorithm, the tree configuration can be reduced to only connections between positive ore nodes. The modified algorithm is shown to require less memory and processing time while still yielding an optimal solution.

Jan 1, 1989

By P. W. Johnson, H. Fan, S. B. Patton, T. Novak, R. L. Sanford

A computer model is presented that quantitatively uses the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasitication on the ventilation system in a longwall panel.

Jan 1, 1995

By R. V. Ramani, R. Natarajan, A. Bhattacherjee

Industries in general, and mining in particular, have become safer than ever before. However, there is a need to increase the search for the causes of mining work-related injuries and to contribute to their reduction, as required, through job redesign, work procedures and worker training. Mine accident and hazard control must be practiced in a manner consistent with the overall objectives of the mine management, which include the optimum allocation and effective utilization of the resources. The purposes of this paper are to: • present a set of analytical tools to analyze injury experience data. • apply these tools on a case study example, • discuss the results of the case study, and • identify the application limitations and the future research needs.

Jan 1, 1993

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

By Nader Shahcheraghi, Verya Nasri, Mehdi Bakhshi, Ali Haghighat

An accidental fire load is one of the major loads considered in design of segmental linings in transit tunnel. Typically, a two-dimensional coupled thermo-mechanical finite element analysis (FEA) is conducted. The conventional approach involves using standard fire curves (temperature-time curves) which can lead to a significant overestimation of fire load and tunnel lining thickness in metro tunnels. The focus of this paper is on the cutting-edge approach, using 3D computational fluid dynamics (CFD) analysis of real train fires in metro tunnels and coupled thermo-mechanical finite element analysis (FEA) to accurately and cost-effectively design fiber-reinforced concrete (FRC) segmental tunnel linings for large-scale metro projects.

Jun 23, 2024

By Lijun Xu, Ragula Bhaskar

The transport of dust particles from a turbulent air stream on to the surface of a mine entry is mainly due to the effect of diffusion, sedimentation and inertial impaction. While the literature in aerosol science contains many references on particle deposition, most studies apply to smooth surfaces in small, short tubes. The deposition data from those experiments may not be applicable to deposition in mine airways that have large areas of rough surfaces and extend several thousand meters. This paper describes the mechanisms of mine dust transportation and deposition, specifically, by estimating the turbulent deposition velocity for coal dust in mine airways. Data from in-mine experiments on ambient dust concentration and dust deposition along a straight entry were used. A statistical model for dimensionless turbulent deposition velocity was developed, and compared with the models developed by other researchers. The model shows that the distance from the dust source is an important factor in the turbulent deposition of mine dust.

Jan 1, 1995

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed.

Jan 1, 1994

By L. Shwydiuk, A. Chrzanowski, W. Newcomen, G. Bastin, R. Wilkins

Automated monitoring of steep embankments allows the early detection of instability and can be used to avoid or mitigate possible slope failures. A system that uses multiple and different types of sensors has been created and successfully tested at the Highland Valley Copper mine in British Columbia. The system uses robotic total stations (RTSs) as the primary measurement sensor, with surveys repeated at predefined intervals selected to optimize operational efficiency. A methodology has been developed to improve the system’s accuracy and reliability by reducing the effects of systematic errors created by atmospheric refraction and unstable instrument and reference point positions. The inclusion of GPS sensors to monitor the RTS positions creates additional operational flexibility and maintains system integrity when insufficient reference stations are available.

Jan 1, 2003

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By R. J. Sterrett

To the average mine operator, the implementation of environmental regulations are viewed as a drain on the profitability of the mine. Since the birth of environmental awareness in the late 1960's, which led to the passage of the National Environmental Policy Act (NEPA) in 1969, and through the publicity brought about by the discovery of Love Canal in 1978, the public are clamoring for increased environmental protection. It should be emphasized that the concern regarding the issues of the handling and disposal of nuclear and toxic wastes is not limited to a few overzealous environmental advocates. Toxic waste issues have "grass roots" interest and support. A reflection of this support has been the passage of key pieces of federal legislation. . Of particular interest are the following acts: Clean Water, Toxic Substances Control, Surface Mine Land Reclamation, the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). The last act is often referred to as "Superfund". Both RCRA and CERCLA have been re-authorized and amended, and in their re-authorization they have been substantially strengthened. Of the last two pieces of legislation, RCRA is the most powerful in that it governs the handling of hazardous wastes from "birth to grave". CERCLA was established to cleanup abandoned waste sites which are threatening human health or the environment. These cleanups can be undertaken by the government and then billed back to the previous owners or to the disposers at the sites.

Jan 1, 1988

By Walter E. McCulloch

Installation of flash flotation in the copper concentrator of Freeport Indonesia in late 1986 and 1987 increased gold recovery by about 13%, while also increasing concentrator throughput. Copper recovery remained essentially the same. Flash flotation has since been included in a recently completed mill throughput expansion to 32,000 t/d (35,300 stpd) as well as in a current expansion to 52,000 t/d (57,300 stpd).

Jan 1, 1991

By D. Tao

More than 80 million metric tons of fly ash is produced annually in the U.S. as coal combustion by-product. Fly ash can be converted to value-added products if unburned carbon is reduced to less than 2.5%. However, most of fly ash is currently landfilled as waste due to lack of efficient purification technologies to separate unburned carbon from fly ash. A rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features. Several fly ash samples have been used to understand the effects of major process parameters on the separation performance. The results show that compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator has significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range. Key words: Coal, Combustion Waste; Fly Ash; Particle charging; Separation.

Jan 1, 2008

By Pierre Mousset-Jones, Felipe Calizaya

This paper summarizes the current research trends in the ventilation design for the construction of very long tunnels, and presents the results of leakage flow measurements in three auxiliary ventilation systems. The study includes an estimation of an important design parameter, namely, the leakage path resistance, and a discussion of its effects on the overall efficiency of a ventilation system. A sample problem is used to illustrate the calculations.

Jan 1, 1997

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993

By Tom C. Palanglo, Norbert Maerz

Control of crushing and grinding circuits ideally requires continuous particle size measurements on both in- and outgoing streams. Until recently, size distributions could only be obtained by screening methods, which were neither cost effective, frequent enough, nor timely. Input streams are often composed of large fragments, making screening prohibitive. Optical image processing systems, such as the WipFrag System, have been developed to the point that they are an extremely valuable tool to characterize, control, and fine-tune the comminution process. Although accuracy is less than that of screening, measurements are precise enough to detect relatively small changes in size distributions.

Jan 1, 2000

By R. Candia

The use of industrial wastes, such as quarry fines of crushed stone, should represent a basic component of sustainable development indicators. Therefore, increasing investments should be foreseen in techniques of treatment and recycling of residues in mining, as well as by-product attainment that generate jobs and income. The standards of identification and discarding of industrial wastes vary significantly between countries. However, practically all nations have started becoming more restrictive regarding environmental legislation, especially concerning production, transport, treatment, recycling and final discarding of industrial wastes. Under an environmental point of view, solid wastes produced by a system (such as a quarry) can be handled in two ways: a) they can be discarded in piles or b) they can be internally or externally recycled and reused. This second practice is translated to an additional economic consequence such as an increase of income as well as a decreased environmental impact. This option is more advanced and should be included in company policy. This paper presents cases where this practice is used, i.e. diminishing the environmental liabilities through the use of the quarry fines in the manufacture of industrial devices, incorporating such wastes in the productive chain, instead of storing them in piles.

Jan 1, 2007

By S. Formby, J. Avraamides

Transportation of sodium cyanide from factory to minesite often attracts adverse comment from both the community and government agencies. In Western Australia the transportation of 30% w/w aqueous sodium cyanide solution raised fears in the community concerning the safety of such material in the event of spillage. The Chemistry Centre of Western Australia initiated a study of the effects of such a spill, to determine appropriate short and long term response strategies. Factors which were considered included the rate of hydrogen cyanide gas release under various climatic and soil conditions and the effect of alternative treatments in reducing such emissions. The data collected have been used to plan emergency response procedures.

Jan 1, 1989