Search Documents

The main goal of this paper is to present readers with recommendations for choosing coaxial cables appropriate for mining applications of Time Domain Ref 1 ectometry (TDR) to monitor rock mass movements. Prior to discussing the recommendations, mining applications are illustrated with examples and the operating principle of TDR is discussed briefly. Items that affect the result of the monitoring system performance include the coaxial cable selected, the grouting material used, and the installation procedure.

Jan 1, 1986

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and concrete is described. Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fast-opening valve discharges the compressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh -pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard, massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited.

Jan 1, 1998

By E. J. Donovan, O&apos

The use of Dynamic Analysis techniques in the design of conveyor systems is extremely limited. The most frequent use of the technique is in large and expensive systems where the emphasis is on insurance against failure caused by catastrophic tension waves. This paper sets out to illustrate a much wider range of applications where dynamic analysis has been successfully employed. The examples chosen deal with identification and correction of dynamic low tension problems, the variability in take-up movement as other system parameters change, the requirement for proper tuning of starting controls and finally the absolute necessity for a complete understanding of the entire system when specifying brakes for critical applications. The intent of the paper is to get designers to view a conveyor as a system of interacting flexible components rather than as a single rigid body.

Jan 1, 1993

By K. C. Carriere

INTRODUCTION The purpose of this paper is to introduce the reader to basic control strategies for solid/liquid separation in mineral processing and to indicate some of the implementation difficulties to be encountered, without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with control systems and with dewatering processes, since exploration of these topics would require considerably more length. The paper is organized into three parts: first a general discussion on the need for control of dewatering processes and of the general criteria involved, next a more detailed elaboration on control strategies for the various unit operations, and finally a case study showing a specific approach towards such a project. Motivation & Objectives The justification for implementing any control system in an industrial plant is to improve operations and thereby to increase profitability. Without this motivation, the system will likely be perceived as unnecessary and will decline into disuse, an expensive and troublesome monument to someone's ill-conceived ideas. However, when a control strategy is correctly conceived, implemented and integrated into operations, it can provide significant advantages in operating ease and efficiency, and a handsome return on investment. In general terms, the objectives in establishing a control system are: • stabilization of process disturbances maintenance of product quality • maximization of throughput • dearer definition of process • protection of personnel and equipment A successful control strategy must address at least some of the above criteria. However, the most important requirement is a commitment on the part of plant personnel and management to start up, operate and maintain the system, and to upgrade it to reflect current process status and operational philosophy. Process Applications In this paper, control strategies will be explored for the most common methods of dewatering of mineral pulps. These unit operations include: drying, centrifuging, filtering and sedimentation. While the first three are important, they do not tend to be as complex as sedimentation, and thus will not be as exhaustively treated. Sedimentation is very widely applied, not

Jan 1, 1986

By Allan D. Fernie

Growing interest in pit crushing and conveying is evident from the many articles, technical papers, and new equipment development recently presented. Application of a pit crushing and conveying system is complex, as many factors such as mine design, production scheduling as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1983

By Barbery G., A. Maachar, M. Bourassa

Laboratory testing for flotation circuit design is carried out on a routine basis in a large number of lab- oratories throughout the world. Usually a sample of ore, assumed to be characteristic of the material to be processed in a future plant, having a mass of the order of a few kilograms, is ground in a batch ball or rod mill, in the presence of water and some re- agents (for pH control, etc. .. ); after dilution to the adequate solid concentration, the resulting slurry is transferred into a laboratory batch flotation machine, having a volume which can vary from 0.5 to 8 10 -3m3. Various types of machines are in common use, manufactured by the same companies that market industrial size flotation machines. The operation of flotation in the laboratory is carried out by an experienced technician, who uses parameters such as impeller rotation speed, air flowrate addition, froth height, froth removal rate, in conjonction with reagent addition sequence, to "test" the ore. After flotation, the froth products ("concentrates"), and the solids remaining in the cell are filtered, dried, and analyzed for the various elements of interest. For flotation circuit design, a kinetic test is usually carried out, in which the froth products obtained at various times are collected to assess the time response of the ore in the laboratory machine with the combination of reagents used. Although this description is rather sketchy, it enables to outline some of the major difficulties in using laboratory data for flotation circuit design: 1. ore sample representatively 2. feed preparation procedure (laboratory compared to industrial scale) 3. laboratory procedures (type of ma- chine, type of operation, experimental errors. . . ) 4. flotation machine scale-up 5. flotation kinetic scale-up 6. flotation circuit design using laboratory data These various points will be discussed in the present paper, in order to stress the problem areas as well as possible solutions. ORE SAMPLE REPRESENTATIVITY It has been stated many times that one of the major problem in designing a flotation circuit is the representatively of the sample to be taken. Sampling of an ore body during prospection and evaluation is a specialized field, which has been progress in with the introduction of geostatistics. The application

Jan 1, 1986

By Rudolf E. Greuer, Xintan Chang

Mine fires have always been of great concern to mining engineers and their behavior has been studied for a long time. Although an abundance of observations exist, no satisfactory mathematical model for their interpretation and extrapolation has become known. The paper presented here tries to close this gap, making use of the laws of chemical kinetics, energy and momentum conservation. To overcome the mathematical difficulties, the fire zone is axially divided into segments and radially into sections, each one with an extension of only a few inches. Conditions in segments and sections are updated in time intervals of one second or less. To solve the large number of resulting equations, a numerical solution is performed. The model has so far been tried on timber fires. It confirms experimental observations on the ignition phases and equilibria of these fires.

Jan 1, 1987

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987

By Surendra K. Mishra

Recent land ban act has put pressure on industry to decontaminate the waste streams before they could be discharged. However, for both metal and organic contaminated wastes, there are commercial incentives to recover usable resources. Recent technology developments have helped meeting such objectives. This paper reviews developments in treatment technologies for industrial wastes. Major chemical groups used in waste treatment are summarized.

Jan 1, 1994

By G. F. Ayakwah

Point load strength (Is50) and slake durability (ID2) indices provide a measure of the strength and durability of rock fragments and are related to the alteration intensity and frictional resistance of the materials. Samples were collected from the rock piles, alteration scars and debris flows at the Questa mine with the purpose of examining relationships between Is50 and ID2, mineralogy, chemistry, weathering, hydrothermal alteration, and other geotechnical parameters. The Is50 from the various rock piles ranges from 0.6-8.2 MPa and the ID2 ranges from 80.9-99.5%. The Is50 and ID2 results indicate that the samples from the debris flows are stronger (average Is50= 4.0 MPa and ID2= 98.4%) than the rock-pile samples and that the alteration scar samples are weaker (average Is50 = 2.8 MPa and ID2 = 89.2%) than the rock-pile samples, but still most of these rocks are strong in terms of their Is50 and ID2. The Is50 decreases as the degree of alteration increases in some rock pile and alteration scar samples, but not in all. However, the majority of the rock fragments within the rock piles still indicate high strength, even after 25-40 years of weathering.

Jan 1, 2009

By John E. Urbanic, William D. Faulkner, Robert W. Ruckel

Guidelines are presented for the selection, handling and regeneration of activated carbon used in gold recovery operations. The guidelines are based on Calgon Carbon Corporation's own investigations and experience gained in working with gold mine operators all over the world. Gold adsorption rate and adsorption capacity are shown to be independent variables thereby requiring testing of both properties when selecting activated carbon. Means of measuring these properties are provided. Historical activity tests on activated carbon are shown to be minimally useful in selecting carbon for gold recovery. Proper thermal regeneration techniques to maximize recovery of adsorption rate without weakening the carbon structure are suggested. Simple positive means of measuring efficiency of regeneration are presented. The subject of hardness measurement as a predictor of "in process" abrasion is discussed. The cost/benefit issue of carbon activity level is addressed.

Jan 1, 1986

By Richard Keith Corbin

INTRODUCTION With the world media full of predictions that the price of gold will quadruple in three years (Maybury, R.J., 1988), and with financial forecasters and strategists touting opportunities to make 400% in gold (Skousen, M., 1988), explorationists and entrepreneurs are scurrying to find enough gold to feed the global gold fever created. At the same time, gold deposits in the United States and other developed and intermediate countries are becoming less attractive because of environmental restrictions, radical reductions in tax incentives, and depleting reserves, causing people in the mining industry to begin looking at opportunities for foreign investment in gold mining concessions in lesser developed countries (LDCs). Meanwhile, LDCs are responding with chamber-of-commerce aplomb in marketing their opportunities. In the face of all this frenzy and hype, targeting gold mining concessions in LDCs for foreign investment may be done more objectively by employing a systematic approach. For this paper the SHOP rating system (Corbin, R.K., 1987), which considers factors of the LDC's stability, hospitability, ore occurrence, and profitability potential is used. The result is that a tiny banana-growing republic in Central America, first discovered by Columbus and named the "Rich Coast'' because of the many gold adornments worn by its Indians, has been rediscovered and emerges as a classic LDC gold target.

Jan 1, 1988

By T. H. Dubaniewicz, J. E. Chilton

The U. S. Bureau of Mines is investigating the application of fiber optic technology to methane and carbon monoxide monitoring. A methane monitoring system is described that is based on differential absorption of infrared light. It can detect concentrations as low as 0.2% and as far away as 2 km via fiber optic cable. The upper range is 100% methane. The system requires no electrical power within the mine so it should operate safely under mine disaster conditions. A hybrid carbon monoxide monitoring system is described that combines a low-powered electrochemical cell with fiber optic telemetry. Testing has shown the system can operate maintenance- free for several months.

Jan 1, 1992

By Robert Roggenthen

In 1994, ASARCO's Mission Complex Mine Planning Department designed a new stripping schedule to take advantage of reserve opportunities. Based upon the new stripping design, overburden removal exceeded available hauling capacity. This increased hauling capacity requirement required that ASARCO consider alternative technologies for material transport. In 1997, ASARCO Mission Complex completed the purchase and installation of a 3.5 km, 8,600-tph conveyor system to transport waste material. The conveyor system is composed of two apron feeder/sizer units manufactured by Mining Machine Development LTD. and a conveyor system manufactured by Krupp-Robbins. This paper will review the option of truck haulage versus conveyor transport for overburden removal by (1) describing engineering studies contributing to the solution, (2) researching proactive options to create alternative management decisions, and (3) revealing final results of the project.

Jan 1, 1998

By Gary S. Brierley, Tracy J. Lyman

INTRODUCTION Geotechnical engineers play a major role in tunnel design primarily because tunnels are constructed entirely within the ground. In general, this role can be divided into two major tasks: subsurface investigations and project design. Under subsurface investigations, it is necessary for the geotechnical engineer to accurately describe the ground in which the project will be built. Under project design, it is necessary for the geotechnical engineer to work together with other members of the design team to make certain that the tunnel fulfills its intended purpose at least cost. Given in the paper are the authors' opinions about what constitutes an adequate scope of services for these two tasks on a tunneling project. SUBSURFACE INVESTIGATIONS o Background Study All subsurface exploration programs for tunnels begin with a thorough investigation of background information about the proposed site. Such background information includes geologic, reports topographic maps, aerial photography, and case history reports of other nearby tunnels. Once completed, it is necessary to study the background information so that the proper scope and magnitude of subsurface exploration work is performed in a manner that provides maximum input to a knowledge of those intact and rock mass properties that are important for an understanding of the entire ground mass. The blind application of field and laboratory techniques, no matter how sophisticated, is wasteful and potentially

Jan 1, 1989

By D. C. Yang, J. Ye

A comprehensive flotation study has been conducted on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University (MTU). The results are compared with those for a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4% to 5% higher recovery and much lower silica impurity than the concentrate produced by up to six stages using a conventional mechanical cell. The results also show that the packed-column flotation process is particularly suitable for the recovery of finer fluorspar particles.

Jan 1, 1993

By J. C. Yingling

An approximate analytic- model is developed for minerals liberation when comminution processes are applied to multi-component ores, i.e., ores that include grains of multiple mineral species. The model employs a one-dimensional representation of ore texture similar to that employed by King (1979) and Klimpel and Austin (1983). The spatial texture representation is viewed as being generated by a stationary semi-Markov process. Associated semi-regenerative processes are defined that can be used to establish, approximately, the joint distribution of particle size and composition, where composition refers to the identities and relative proportions of mineral species included within the particle. Numerical predictions made by the model are compared to size and composition distributions observed in previous experimental studies.

Jan 1, 1992

By David L. Gefvert

A general review of the role of cationic flotation reagents in the beneficiation of phosphate, iron, and potash ores. The three major types of cationic collectors-amines, ether amines, and condensates will be compared and contrasted. The effect of particle size, water chemistry, and water temperature on the choice of cationic flotation reagents for each industry will be discussed.

Jan 1, 1986

By Steven A. Tesdahl

Maintenance means keeping equipment running or restoring it to operating condition. However, the 21st century will usher in a broader need for equipment management, a cradle-to-grave strategy to preserve equipment functions, avoid the consequences of failure and ensure the productive capacity of equipment. Profitable future mining operations will have reduced the 35% of operating costs typically spent on maintenance and the unfavorable impact of downtime that often multiplied these costs by 300%. They will survive those operations that tried to carry outdated "maintenance" thinking beyond the year 2000. These surviving operations will have applied modern management techniques, technology and information to align the efforts of people with the needs of equipment. Future managers will use equipment management as an integral part of an overall production strategy. They will see it as a means of raising productivity, improving performance and minimizing downtime to maximize profitability. This global thinking will characterize all operations planning to survive in the competitive world of mining of the next century.

Jan 1, 1998

By D. L. Jones, S. Knoerr, J. Mansanti

The Buckhorn Mine in Nevada currently treats oxide ore using heap leach methods, but exploration has identified sulphide reserves which are refractory in nature. Preliminary testwork was conducted on the sulphide material to screen potential pre-cyanidation treatment methods. Processes evaluated included pressure oxidation, biological oxidation, nitric acid oxidation and roasting. An initial economic and process analysis of the results concluded that roasting was the only viable process, and only if the roaster off-gases were converted to soleable sulphuric acid. Further economic analysis indicated that roasting of the whole ore was more attractive than pre-concentrating by flotation, followed by roasting of the concentrate. These results were generalized to show that for high sulphur ore a roaster/acid plant combination is more attractive that either of the other options, ie. pressure leaching or bioleaching, provided the by-product acid is soleable.

Jan 1, 1990