Search Documents

By A. M. Wala

It is common practice in Appalachia, when extending the life of an existing mine, to acquire the adjacent reserves and extend the existing mine into it. Also, often the existing mine is renovated to accommodate the new conditions. The existing mining system and the track and belt haulage systems may be modified while the new property is integrated into the old one. All of these changes create new constraints for the mine ventilation system (M.V.S.) that require proper planning and control procedures. The authors describe and present the study that was carried out for the ventilation system of a newly expanded underground coal mine located in the Appalachian coal region. Discussed first is the process of correcting the ventilation system of the existing mine. Then, some of the stages of controlling the expanded system are discussed. Finally, numerical data for these steps are presented.

Jan 1, 1992

By Ferdi Camisani

The ‘Bible’ 1977 & 1981 ‘South African Mine Valuation’ by C. D. Storrar. Proved reserve (=’measured ore’ USA; ore reserve = the payable portion of the proved reserve) -Fully developed (…immediately available…) -Partly developed (…not immediately available…) -Undeveloped (…unavailable…) Probable reserve (=’indicated ore’ USA) Possible reserve (=’inferred ore’ USA) Life-of-mine reserve (Proved + Probable + Possible)

Jan 1, 2003

By Marc E. Orman, Mark E. Smith

Regulatory and environmental concerns continue to broaden the range of mine wastes that must be capped with low permeabili­ty liner systems at closure. The mining industry has been a leader in developing liner technology for leach pads and tailings impoundments, but it is a newcomer to cap designs. Closure of waste piles, leach heaps and tailings require special design con­siderations. Factos such as differential settlement, surface ero­sion, veneer stability, vegetation and burrowing animals must be considered.

Jan 1, 1996

By John M. Wootten

The development of new coal markets is -t upon the ability to utilize coal in an environmentally acceptable and economically viable fashion. Foremost in the concerns about coal utilization is the impact its combustion has on air pollution. Concerns over environmental issues, such as acid rain, are currently one of the major impediments to the development of new coal markets. The Department of Energy and the Synthetic Fuels Corporation are addressing certain aspects of the development of new technologies for the utilization of coal. However, at the present time, there is a void in the new technology development process. That void is the step from proof- of-concept to commercial demonstration. Congress has established the Clean Coal Technology Fund at a level of $750 million to fill this void. The Department of Energy, in a solicitation of interest, received over 175 proposals for commercial demonstrations of clean coal technologies. A review of these solicitations indicates that $1.2 billion worth of research could be accomplished with a federal cost sharing of $425 million or 35 percent of the total. Industry has indicated, through this response, its willingness to invest its limited funds on projects it feels have the greatest potential for the clean use of coal. What must now occur is that Congress must appropriate the monies from the fund to initiate the commercialization of these clean coal techno1ogies.

Jan 1, 1986

By P. Todd, K. Dever, P. S. Mills, A. A. Campoli

Resin bolt performance is dependent on the size of the resin annulus, i.e., the difference between the hole and bolt radii. The majority of the millions of resin roof bolts installed each year in the United States employ an annulus of 3.175 or 4.775 mm (0.125 or 0.188 in.). Short encapsulation pull tests with resin annuli of 3.175 and 2.413 mm (0.125 and 0.095 in.) resisted an average of 0.08 t/grouted mm (2.25 st/grouted in.) with no significant variation. Resin loses to simulated fractures increased as annulus size decreased.

Jan 1, 2003

By Jozef Szymanski, Julian Partyka, Jerzy Krynicki

In order to study blast-induced dust in a hard rock metal mine experimentally and analytically, a part of a stope mined by Vertical Retreat Mining (VRM) was monitored throughout its lifetime. Dust measurements were used to describe the dust source, to study the dynamics of removal of airborne dust from the blasting area, and to examine a variation in dust production with a stope's progress. An analysis based on graphical and analytical comparisons of blasts taking place in a single stope is presented and discussed. Also, some transient phenomena of dust flow in the stope vicinity, caused by the blasts only, are examined.

Jan 1, 1997

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982

By J. R. Sturgul

A dynamic input-output model for a coal power enterprise that now includes four underground coal mines, three coal washing plants, a power plant and a railway transportation system was developed. The model is applied to analyze investment alternatives for long-term development, including the expansion of existing mines, the opening of new mines, the construction of new coal washing and power plants and the upgrading of the railway system. As a result, the optimal investment strategy with capital schedules and projected sector outputs is obtained. Also, the importance of the new power plant to the strategic development of the company is demonstrated. It is concluded that, without applying a dynamic input-output model, it would be much more difficult or impossible to conduct such a systematic and compete analysis.

Jan 1, 1999

By Andrzej Wala

Constantly increasing demand for energy materials and metal ores brought about tremendous progress in mining techniques which are characterised by a high degree of mechanization and concentration of works. One of the recent trends in underground mining mechanization is connected with an application of heavy machines with diesel engines [l],[2]. The introduction of diesel engines in mining all over world caused not only improvement in economic conditions but also the necessity to prevent contamination of air in the mine by toxic agents in diesel exhaust emissions. A generally used way of eliminating exhaust gases is proper ventilation of the cross cut by means of providing permanent exchange of air that would guarantee in every point of the cross cut and in every moment the decay in concentration of exhaust gases beyond threshold limit [3][4][5][6][7][8][9][10]. The present paper is an attempt to define a mathematical model describing the changes of concentration in cross cut face to which fresh air is distributed by ventilators and tubes in a forcing way. Obtained model should offer its practical adaptability to engineering calculation of the amount of fresh air needed for diluting and eliminating exhaust gases beyond threshold limit. Justness of these models has been confirmed by investigation of the growth of nitrogen dioxide concentration in air environment in some cross cut faces of Kiirunavaara iron ore mine in Kiruna (Sweden).

Jan 1, 1980

By G. Kris Kapoor

Each new period of public concern, whether rooted in things political, social, economical, or technological, brings with it new words or phrases which highlight that new interest. With people's awareness of our rapid depletion of readily available energy sources and the enormous increase in energy .costs came the new, and now often heard, terms "energy intensive", "energy sensitive", and "energy conservation". Since its birth in 1926, Fuller Company had been directly associated and involved with energy intensive products and processes. We are located in the heart of the Cement Industry. Many of our products and processes are geared to the needs of the portland cement manufacturer, and a look at the inferno within an operating cement or lime kiln will certainly convince anyone that here is an energy intensive process. Fuller Company, then, has always been energy sensitive. Process kilns, hard rock crushers, tube and roller mills, fluid bed thermal reactors, pneumatic compressors and conveyors, material coolers - all are Fuller Company products utilizing or transferring large amounts of energy. Consequently, much of our success in the marketplace depends on how wisely we design and plan for efficient use of power and for conservation of each unit of heat available.

Jan 1, 1975

By Bruno Paponetti, Luigi Toro, Carlo Abbruzzese, Maria Y. Duarte, Anna Marabini

A bioleaching process has been developed to extract manganese from low grade domestic resources not amenable to conventional mineral processing operations. Between the different strains of microrganisms tested, Thiobacillus ferrooxidans has appeared poor over manganese, Aspergillus niger allowed to obtain high recovery, probably due to the metabolic production of citric and oxalic acids, showing a remarkable complexing and reducing action. The growth of microflora has been correlated to the MnO dissolution as confirmed by SEM observation.

Jan 1, 1989

By J. D. Raulerson, R. P. Farias, G. A. Gruber

A flotation process has been developed to successfully treat ore from the Santo Domingo phosphate deposit in Baja California Sur. The ore contained less than 4% P2O5 with quartz, silicates, and carbonates as gangue minerals. Flotation of the low- grade feed in seawater required that the conventional Crago process, comprising direct anionic flotation, deoiling, and inverse cationic flotation, be augmented by an anionic cleaner flotation step, phosphate depression, and a calcite flotation step.

Jan 1, 1988

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL HYDROLOGIC REGIME The total hydrologic cycle must be considered when evaluating potential ground water problems in a mining environment. Precipitation is the ul¬timate source of all surface water and essentially all ground water. Stream flow during low flow periods often orig¬inates as seeps or stream gains (base flow) where the water table intersects the land surface. A stream that is higher in elevation than the ground water system may lose flow, thereby recharging the ground water system. The magnitude of stream gain or loss is dependent upon the hydraulic conductiv¬ity and related properties of the underlying hydrostratigraphic units. Ground water moves constantly from recharge areas to discharge areas (streams and springs) usually at very slow rates. Large quantities of ground water may be in¬tercepted in many underground mining environ¬ments. Construction of an underground mine in saturated formations may encounter ground water inflows ranging from very small to very large and from continuous to intermittent depending upon the hydraulic properties of the hydrostratigraphic units penetrated. SURFACE WATER VARIABLES Precipitation occurs in different forms, varying amounts, and with a wide assortment of temporal and areal distributions in the various mining dis¬tricts within the United States. Mine inflow can be affected in a matter of hours by precipitation events where there is a direct hydraulic interconnection between the mine and the surface through fractures or a mine opening. The timing, form, amount, and distribution of precipitation should be evaluated in a mine inflow study. A portion of the precipitation that falls in a topographic basin moves as sheet flow to runoff channels (Fig. 1). Some of the precipitation infil¬trates the unsaturated soil zone where it can either move laterally as interflow to the surface system to augment stream flow or move downward as re¬-charge to the ground water system. The unsatu¬rated zone (called the zone of aeration or vadose zone) can range in thickness from essentially zero to a few hundred feet. The saturated zone or ground water system occurs below the water table (zone where hydrostatic pressure is greater than atmos¬pheric pressure) where all the pores are filled with water (Freeze and Cherry, 1979, p. 44). Moisture can be lost from any of the systems (surface water system, unsaturated zone, and ground water sys¬tem) by the processes of evaporation and transpir¬ation which return moisture to the atmosphere. Stream flow consists of runoff and interflow components plus an additional base flow compo¬nent (Fig. 2). Base flow constitutes ground water discharge to a stream. Base flow plays an increas¬ingly significant role as total stream flow declines. Base flow is important because it constitutes much if not all stream flow between periods of precipi¬tation when runoff and interflow have largely dis¬sipated. INTERACTION OF SURFACE WATER AND GROUND WATER SYSTEMS Recharge from a surface water system to ground water systems can occur via unsaturated or saturated flow. The amount of recharge is depen¬dent primarily upon the vertical hydraulic conduc¬tivity of the formations underlying the stream and the availability of water. Streams that flow over low hydraulic conductivity formations lose little water even if the ground water levels are significantly lower than the stream. A ground water system may contribute flow to a surface water system but nor¬mally only by saturated flow. This contribution usually takes the form of seeps, springs, and the base flow of streams. GROUND WATER VARIABLES Introduction The variables that affect ground water flow are discussed in increasingly complex theoretical situ-

Jan 1, 1986

By Cao Changlin, Gong Qian, Hu Jiexue

The thiosulfate, effects copper of concentrations of and ammonia ou the extractlon of gold from sulfide gold concentrate have been studied. The experimental results showed that it is possible to reduce thiosulfate concentration. Above 95% of gold extraction was obtained in O. 2M thiosulfate leaching solution in two hours under the suitable conditions. Therefore, the process of washing residue was simplified, the consumption of thiosulfate and the loss of thiosulfate carried were reduced. by washing residued.

Jan 1, 1992

By A. M. Marabini, G. Belardi, V. Alesse, E. Spaziani

The objective of this investigation was to verify the effectiveness of commercial and synthetic depressing agents in a complex oxidized zinc mineral flotation flowsheet using sodium sulfides and amine. The flotation tests were run on a finely-disseminated calamine ore grading 16.96% Zn and containing smithsonite, hemimorphite, cerussite, calcite, quartz and iron oxide, present essentially in colloidal form. The reagents used in the testing can be grouped into four classes: guar, starch, celluloses and acrylic polymers having various degrees of substitution and molecular weights. The depressants exhibiting the greatest selectivity towards the gangue (considered as a whole) are tripolyphosphate, polycarboxylic acids, methylcarboxylate guars and ethyl hydroxylic starch. In the rougher stage, the Zn recovery ranged from 70% to 80%, and the Zn grade ranged from 27% to 29%. In the Zn-Fe2O3 separation, the compounds ensuring the most efficient separation are the tripolyphosphate and the polycarboxylic acids. In the Zn-SiO2 separation, the compounds that exhibit the best separation efficiency are tripolyphosphate and guar of methylcarboxylic sodium salt. In the case of the Zn-Ca separation, methyl-carboxylic guar exerts the best depressing effect and does not adversely affect the Zn recovery. The separation provided by ethyl hydroxylic guar is also good, although not as good as the preceding reagent. Regarding the Zn-Al separation, the tripolyphosphate, the celluloses and the carboxylate guars are the best depressants. A hypothesis is advanced to interpret the depressing action of the most effective reagents.

Jan 1, 1995

By Jed H. (Original by) Mosgrove

Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 ma/s (9000 cfm) of air at his last open crosscut.

Jan 1, 1981

By J. L. Thompson

The combustion of pulverized coal is a century-old practice. Many people have investigated coal dust and the residual fly ash particles that re-main after combustion. But the combustion process and fly ash formation mechanism are not under-stood. Working at our Maysville, Kentucky lime plant, the Dravo Lime Company Research team has collected samples of partially burned coal dust from the flame of a pulverized coal burner. Specimens were placed in a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). Microscopic examination of the particles, together with a large collection of micrographs of lime dust fused to fly ash particles, now make it possible to theorize as to how combustion advances through a piece of coal dust. Coal is a physical mixture of carbon-based compounds interspersed with bits of ash-forming materials, primarily alumina-silicate compounds. The alumina-silicate materials are commonly in angular nodules measuring 100 A to 700 A across their major dimension. It would appear that if the coal particle is in a well mixed gas stream, combustion starts at the surface and advances radially toward the particle center. With poor gas mixing, it is common that combustion moves from one end of a particle and advances on a broad front almost normal to some axis. In either case the combustion process and ash-forming mechanism are the same. As combustion occurs the carbon-based compounds oxidize in a highly exothermic reaction. Heat from the re-action melts the alumina-silicate nodules causing them to flow together and coalesce into an open sponge-like structure. As melting continues surface tension of the liquid and free surface energy causes the sponge-like structure to simplify into fewer, larger pores. Most likely the lighter molecular weight hydro-carbons burn before the heavier species. This means that as the melting ash structure is metamorphosing to a single large pore, there continues to be out-gasing throughout the structure due to combustion. Surface tension will form a spherical piece of fly ash if the ash material is liquid for a sufficient period of time. Out-gasing from combustion of the heavier hydro-carbons will provide internal gas pressure to keep the particle spherical until it freezes.

Jan 1, 1978

By M. S. Vernon, J. J. Kellar, W. M. Cross, R. M. Winter, F. J. Johnson, A. G. Pommer

Three substrates (MgO crystal, CaF2 crystal and Mg plate) were used to construct thin layers of Mg(OH)2. Various routes were used to modify these substrates, including surface hydration and sol-gel coating. In each case, it was found (by using Fourier transform infrared spectroscopy) that thin layers of Mg(OH)2 could be produced. In the case of hydrated layers, the surface morphology of the Mg(OH)2 resembles the bulk platelet shape of precipitated Mg(OH)2.

Jan 1, 2000

By Hans von Michaelis

The revolution in development of new technology and practices in the gold mining and metallurgy industry continues unabated despite the ups and downs in the gold price. Some of the new cutting edge technologies are listed in Table 1 overleaf. There is room to discuss just a few of these here, but many more are identified and described in RANDOL (1992). Cutting edge advancements in gold recuperation, can be sorted into three categories. The first category includes fundamental advances that offer major improvement with significant economic benefits. Second would include evolutionary developments that offer smaller, but nonetheless commercially valuable improvements. Finally there are those "advances" that are interesting but of trivial or question­able economic benefit to industry. It is essential to adopt a "systems approach" philosophy towards developing and applying new technology. Practical innovation often comes about as a result of having to solve a problem. Innovation for innovation sake is an ego trip. Environmental management has become an important part of the system and the environmental implications of new processes and practices in the mine and mill have to be carefully considered for potential benefits and/or liabilities.

Jan 1, 1993

By J. DuCarme, A. Smith, M. Reyes

"A magnetic proximity detection system is mounted on a mobile mining machine to prevent underground workers from being pinned or struck by machine motion. The system generates magnetic fields around the machine to determine safe working distances. The minerworn component measures the magnetic field in order to approximate location. Large masses of steel, such as those from mining equipment, can alter the magnetic field distribution. This affects the locational accuracy of the system, thus adversely impacting worker safety. To examine this problem, U.S. National Institute for Occupational Safety and Health researchers developed a method and test system to study the influence of a steel mass on the magnetic field distribution. The results show that a steel plate can strengthen the magnetic field perpendicular to the generator by up to 40 percent. Furthermore, they show that the degree of the influence on the field distribution is a function of distance. The results from this study can be used to further develop and improve the performance and reliability of electromagnetic proximity detection systems used in underground mining applications.IntroductionOn average, 250 miners are injured every year, and 43 miners were reported to be killed by striking or pinning accidents involving continuous mining machines in the United States between 1984 and 2015, according to the U.S. Mine Safety and Health Administration (MSHA, 2015). Continuous mining machines are large mobile machines used to mechanically cut coal in underground mines. These machines weigh approximately 60 t (132,000 lb) each. Although modern continuous mining machines can be remotely controlled, operators still need to be close to the machine primarily because of the low visibility and wide blind spots of the underground working environment.The MSHA promulgated a final regulation in 2015 that requires the use of proximity detection systems on all continuous mining machines except fullface machines. MSHA has approved five such systems to be intrinsically safe for use in underground coal mines: (1) Strata Worldwide’s HazardAvert System, (2) Frederick Mining’s Model 200 HazardAvert Detection System, (3) Nautilus International’s Coal-Buddy System, (4) Matrix Design Group’s M3- 1000/Joy Global SmartZone Gen 1 and (5) Matrix Design Group’s IntelliZone/ Joy Global SmartZone Gen 2."

Jan 6, 2018