Search Documents

By R. E. Johnson, L. V. Araújo, B. R. Palmer, L. M. Abrantes, G. W. Warren

The behaviour of chalcopyrite - mineral specimens and a Portuguese concentrate - in 2M chloride solutions prepared from hydrochloric acid and sodium chloride, has been characterized by cyclic voltammetry. The study has shown the influence of the potential and of the presence of impurities in the reaction schemes and their relative extent. The dissolution of chalcopyrite concentrate under potentiostatic control has been investigated and found to confirm the effect of the selected potential on the surface modification/rate of dissolution. An attempt has been made to correlate the information obtained with the response of the concentrate electrode to constant current treatments.

Jan 1, 1993

By Ugo Preti, Gianfranco Ferrara, Mark C. Williams, Thomas P. Meloy

Theoretical and experimental lockedness profile curves are the same when the model assumptions are met. They appear different because of the way the data is presented. Continuous theoretical lockedness profile curves present all the data, including the wings of the curves giving them the deep U-shaped configuration. Experimental lockedness profile curves, because of the measurement methods, are discretized, obscuring the wings. If the continuous theoretical curves are discretized, they are similar to the experimental curves. When a float sink test is used to measure an interval of locked particles, the integrated averaging of the separation process obscures the wings of the continuous theoretical curve. To disclose the wings with experimental data, narrow density or measurement intervals must be used.

Jan 1, 1992

By W. C. Smith

Even with conservative mine planning, rib instability can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation. sporadic zones of progressive rib instability were detected that culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1991

By John J. Mancini

Elastomeric liner products have been used for over two decades in a wide variety of uses including pond liners, hazardous waste barriers, dam face rehabilitation and mining applications. Asphalt blended with polymers is enjoying renewed interest in the engineering community because of its durability, high yield attributes, fewer CQA steps due to seamless installation, and ease of installation and repair. As in other lining technologies, advancements in polymer chemistry and improvements in installation techniques have had dramatic impact on the quality of fluid-applied asphalt (FAA) membranes. Membrane 6, man­ufactured by Deery Oil, Inc. for over 16 years is a hot-applied polymer modified asphalt membrane that can be applied to a variety of substrates in a reinforced configuration or installed directly on an asphalt surface. By blending thermoplastic polymers with asphalt, very favorable stress/strain characteristics can be achieved (Chambers, 1980). Typically the membrane will yield under rel­atively low stress and also exhibit high elongation capability. In service applications where puncture resistance is a concern, fluid applied asphalt materials have the flexibility and com­pressive strength under heavy loading that leach pad designers may find attractive. Additional security is achieved if long term service life is important as in the case of radioactive waste con­tainment. The Department of Energy selected Membrane 6 over seamed liners for a surface barrier that must isolate and contain radioactive waste for 1000 years. Asphalt has a long history of use as a water-stop material and it is believed that this natural construction material combined with SBS polymers will per-form for a millennium. (Freeman, 1994) The process of installing Membrane 6 varies according to job size and the type of surface to be protected. Lining applica­tions on compacted substrates require the membrane to be applied to a scrim cloth (fig 1). Some early pioneers in FAA technology neglected this step and therefore never achieved per­formance levels that satisfied regulatory guidelines. The scrim provides a cohesive surface that promotes membrane flow while achieving high impermeability (2Xl0 '11).

Jan 1, 1996

By R. N. Rothan, V. Khunova, C. M. Liauw, G. C. Lees

The interphase modification activity of 1,3-phenylene dimaleimide (also known as m-phenylene bismaleimide (BMI)) has been studied in composites based on magnesium hydroxide (60% w/w) and a polypropylene block copolymer (PPBC) that featured an ethylene-rich elastomeric impact modifier phase. BMI was found to be a unique product that led to significant simultaneous improvements in composite strength and toughness, even at the high filler levels. BMI modification was found to promote encapsulation of filler particles with the elastomeric phase of the PPBC together with formation of a PP boundary layer of increased crystalline content.

Jan 1, 2003

By D. Crouse

A significant wollastonite resource has been discovered and evaluated near Seeley's Bay in southeastern Ontario. The deposit occurs in Grenville Frontenac Terrane granulite facies rock within a calc-silicate skarn in contact with Proterozoic-age gabbro. The steeply-dipping and tightly-folded wollastonite skarn beds are interlayered with diopside and quartz-feldspar skarns in a southwest-plunging synclinorium. More than 9 million tonnes of a drill-proven and inferred resource grading 41 % wollastonite has been identified, as well as an additional 3 million tonnes grading 30%. Mineralogical and process test work with the wollastonite from this deposit has demonstrated the potential to produce a high purity, high aspect ratio wollastonite product.

Jan 1, 1994

By A. F. Edwards

The Main Pass sulphur and oil deposit is located at Main Pass Block 299 in the Gulf of Mexico, 30 miles east of Venice, Louisiana, in 210 feet of water. The deposit was discovered by Freeport-McMoRan and its joint venture partners, IMC Fertilizer and Homestake Mining, in late 1988-early 1989. The sulphur deposit contains 67 million long tons of recoverable sulphur. The sulphur occurs in bio-epigenetic limestone replacing anhydrite caprock on top of a salt diapir. Recoverable reserves of 39.4 million barrels of oil and 9.1 billion cubic feet of gas are also contained in the limestone caprock and in supracap sandstone stringers.

Jan 1, 1992

By M. Leroux, S. R. Rao, J. Kim, V. Gervais, J. A. Finch, G. Labonté, N. Macminn, M. Ounpuu

Collectorless flotation of sulphide minerals from Lyon Lake ore (Mattabi Mines Ltd.) has been studied both in the laboratory and plant. Among the four major minerals chalcopyrite showed the greatest response to collectorless flotation, followed by galena. Flotation of sphalerite and pyrite was minimal. Collectorless flotation was influenced by pulp potential and pH. Experiments using different gas compositions showed collectorless flotation was promoted when the pulp potentials were greater than about 0 mV (SCE). The study of the effect of depressants showed that SO2 at pH < 8.0 depresses both galena and chalcopyrite but at pH 9.5 flotation of chalcopyrite recovers. Use of NaCN preferentially depressed chalcopyrite compared to galena. Preliminary results from plant tests at Mattabi Mines Ltd. confirm that collectorless flotation occurs and that it is preferential for chalcopyrite and to a lesser extent galena. Practical implications of collectorless flotation in plant practice are discussed. A critical factor will be silver recovery.

Jan 1, 1989

By Huang Kong Xuan, Li Yun Teng

Reviewing the development of resin-in-pulp (RIP) technology for the extraction of gold in the world, especially in South Africa and USSR, and the chemistry of interaction between aurocyanide ions and anion-exchange resins. RIP benchtest and pilot plant investigations show that the resin of the weak-base and strong-base can absorb gold in the cyanide pulp and gold can be eluted from the strong-base resin by electro-elution. The possibility of future application of RIP technology in China fa also briefly discussed.

Jan 1, 1998

By Gilles A. Tremblay

Acidic drainage has been long recognized to be the largest environmental liability facing the Canadian mining industry and to a lesser extent the public through abandoned mines. The Mine Environment Neutral Drainage (MEND) Program was the first initiative formed in 1989 to develop scientifically-based technologies to combat acidic drainage. This 9-year volunteer program reduced the liability by several hundreds of million dollars and established Canada as the recognized leader in research and development on acidic drainage for metal mines. MEND 2000 is a three-year program that started in 1998. The key to MEND 2000 is technology transfer- providing state-of-the-art information and technology developments to users. MEND-developed technologies are being verified by long-term monitoring of large-scale field tests. Maintaining linkages with a number of foreign government and industry-driven programs is also important to the successful completion of the program. Through these efforts a further reduction of the environmental liability associated with acidic drainage will be realized.

Jan 1, 2000

By Joseph B. Alberts, David D. DiPonio, Francis B. Manning

From 1996 to 2001, Wayne County and 13 suburban Detroit communities constructed the Downriver Regional Storage and Transport System (DRSTS) to improve area water quality, protect public health and alleviate basement flooding. The project consisted of a 10-mile long storage and transport tunnel, a pump station at the existing wastewater treatment plant, 9 miles of relief sewers (6 in tunnel and 3 in open cut). The work was separated into 10 contracts. Due to hydraulic design requirements and other constraints, the tunnel profile was located generally 65 feet below ground surface within a soft to medium clay strata which skimmed along the top of a very dense glacial till “hardpan” overlaying bedrock. Boulders within the tunnel bore were recognized as a significant, but indeterminate risk. This paper presents a case history of the owner’s contracting strategy for risk assumption and management of the boulder impacts on the project. Actual conditions encountered during construction and contractual adjustments made to address problems are reviewed, and recommendations for future contracts are included.

Jan 1, 2003

By John T. Cumberlidge

The Groveland deposit, in the Upper Peninsula of Michigan, consists of an E -W trending overturned syncline of Middle Precambrian Vulcan iron formation. At Groveland, the Vulcan formation can be divided into four units or facies. The total succession may be more than 550 feet thick, and consists of a basal unit composed of a lean chemical quartzite with traces of magnetite; a non-banded, partly clastic unit characterized by the preponderance of hematite over magnetite; a transition unit of well-banded magnetite-bearing iron formation interbedded with non-banded oolitic hematite; and a well-banded magnetite-quartz silicate unit at the top of the exposed sequence. The present magnetite-hematite ratios of different units within the orebody are considered to be a primary (post-diagenetic) feature of the original sediment. Subsequent regional metamorphism has increased the grain size of the original iron oxide minerals, but did not appreciably alter the oxidation state of the original sediment.

Jan 1, 1964

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

By Alexandr A. Abramov, Svetlana M. Angelova, Oleg P. Maljuk

In this paper the effect of the ratio of grinding and grindable size classes (ore lumps, particles and grains) and the guantity of intermediate size classes in the feed of the primary wet autogenous grinding "Cascade" mill is studied and the features of the influence of these factors on the mill capacity are shown. On the basis of the experimental data from Lebedinsky mineral processing plant, where magnetite guartzites are processed, a coefficient of the "total ratio of size classes" in the feed of 9x3 m "Cascade" mill was estimated. It helps to get an evaluation of the effect of ore size classes ratio in mill media on the mill capacity and to work out some ways for its optimization in closed or semiclosed technological circuites of primary autogenous grinding. The operation of the specific energy effects for some intermediate size classes, removed from the mill as circulating load, is proposed to improve its efficiency before regrinding in "Cascade" mill and decrease negative influence of such classes accumulation in the mill media.

Jan 1, 1995

By William L. Barnes, Maurice Leiser

INTRODUCTION The literature on project management considerations and techniques for large rail rapid transit projects in mid-1979 was fairly large and getting larger. UMTA was establishing special organizational elements to deal with the subject as it related to those properties requesting capital assistance, and comprehensive project management plans were being requested from those properties as an early step to build confidence in UMTA that the particular project could be planned, designed, and executed efficiently and effectively, thereby using critically short capital assistance funds to best advantage. In the late 60&apos;s and early 70&apos;s, the choices of models for heavy rail construction would have been quite limited.., and perhaps much simpler than was the case in 1979. One of the writers was with an agency in 1979 in the process of finalizing its organization for project implementation after several years of study and had the opportunity to review the experiences of others at length, presumably to build on the success and to try to avoid the pitfalls and failures. The properties that were surveyed all reported more or less success stories. One could only conclude that there are many ways to organize for a major transit (construction) project and that there is a great variety of viable management structures, but it seemed that chances for success were best where the executing property had prepared a comprehensive project management plan, then resolved to follow it. Perhaps more important, a commitment or prior approval had been sought from UMTA as to the validity of the project management plan, and the property was allowed to proceed without detailed prior UMTA review or approval of all specific intermediate steps. Most important, however, an early overall UMTA funding commitment had been obtained that permitted some reasonable expectation of the rate of funding, perhaps by commitment

Jan 1, 1981

By Kwangmin Kim, Taehee Lee, Minkyu Kim, JUNHYEOK PARK

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. About 25 percent of the mass fraction of tailings from a hard-rock mine consists of particles of a respirable size (smaller than 10 μm) [1]. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. Respirable tailings dust, primarily composed of quartz or free silica (SiO2), may cause silicosis, chronic pulmonary disease, bronchitis, collagen vascular diseases, and chronic granulomatous infections [2]. 

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By Max B. Holfeltz

[Many factors impact the selection of one mining method over another for deep seated, thick seam coat deposits. Generally if an operating mine is recovering coal at high volumes from thick seams then a truck/shovel fleet is required for coal loading. The next consideration is how to remove the associated burden. If an operation has relatively small amounts of burden associated with the coal then a truck/shovel fleet may be employed for burden removal simply to standardized the entire mine equipment concept. On the other hand large amounts of burden associated with the coal can justify employment of draglines for burden removal. Specific economic, productive, and physical factors contribute to the final decision.]

Jan 1, 1983

By Bernd Hagenah, Petr Pospisil, Colin Santangelo

This paper explores the profound implications of high-speed train operation on tunnel planning, specifically investigating ongoing high-speed rail projects in California and Texas. The paper delves into the crucial considerations for designing high-speed rail tunnels, including selecting tunnel sections based on aerodynamic factors, which impacttraction power requirements and pressure comfort. The paper also examines the need for emergency stations, maintenance access, and comprehensive safety and rescue concepts to address train incidents. Drawing from international high-speed rail projects, it shares valuable experiences and lessons learned to promote efficient and secure tunnel designs for high-speed train operations.

Jun 23, 2024

By Carson Rife, Michael L. Clark

INTRODUCTION Zortman Mining Inc. is a wholly owned subsidiary of Pegasus Gold Corporation of Spokane, Washington. Pegasus has been producing gold and silver from the Zortman and Landusky mines since 1979. The Zortman and Landusky mines are two distinct open pit mines located approximately 6 kilometers apart in the Little Rockies Mining District of north central Montana. The two mines use large-tonnage, low- grade heap leaching techniques to efficiently process the gold and silver ore. PROJECT DESCRIPTION The Little Rockies rise abruptly 914 metres from the surrounding plains to about 1829 metres above sea level. The topography is quite steep, making efficient leach pad construction a major challenge. The climate is semi-arid with moderate summers and occasionally severe winters. Freezing temperatures usually arrive in late October or early November, influencing the effectiveness of leaching operations. GEOLOGY AND MINERALOGY The geology of the Little Rocky Mountains consists of steeply dipping sedimentary ridges forming an elliptical dome surrounding a core of intruding syenite porphyry. Within the syenite porphyry are well fractured and mineralized shear zones where the existing reserves and open pits are located. The ore is presently divided into oxidized, mixed, and sulfide. Only the oxides and mixed zones that are of ore grade are placed on the leach pads. The syenite porphyry host rock enables effective leaching of gold and silver to depths of 61 metres, having a major impact on leach pad construction costs. MINING All mining since 1979 has been by contractor. This enabled initial mining to commence without capital investment in equipment. Through competitive negotiations, Pegasus has been able to keep contract mining costs at levels very close to what would be experienced if Pegasus had purchased equipment initially. Contracts are negotiated yearly and are based on a unit price and haul distance for ore and waste. Haul distances have ranged from as little as 457 metres to as much as 3,050 metres. At present, Pegasus is developing a 27,000,000-tonne leach pad at the Landusky project that is adjacent to the minine area. This design feature will reduce the mining cost by 20 percent over the life of the mine. In 1987, over 5,900,000 tonnes of ore and 3,200,000 tonnes of waste will be mined at the Landusky project. Through 1986, 13,763,000 tonnes of ore have been mined at a waste-to-ore strip ratio of 0.60:l at the Zortman project, and 13,005,000 tonnes of ore at a waste-to-ore strip ratio of 0.79:l have been mined at the Landusky project. Current mining reserves are 32,769,000 tonnes of ore at a waste- to-ore strip ratio of 0.59:l. Through efficiencies of large-scale heap leaching, Pegasus has been able to lower the mining cutoff from 0.34 grams per tonne gold to 0.27 grams per tonne gold. This has reduced the mining cost per tonne of ore h percent through a reduction in strip ratio of 14 percent. Beginning in 1984, all pits were designed based on computer-generated "floating cone" pits. The geologic models were developed by Pegasus staff with a series of economic models evaluated. The resulting computer-generated pits were used as a guideline in designing the mine plans, including haul roads for final calculation of tons and grade. Input to the floating cone models consisted of mining cost, processing cost, cutoff grade (0.34 grams gold per tonne), recovery (67 percent) and gold price. Due to the gold being deposited primarily on the fractures of the syenite host rock, no crushing of ore is needed prior to leaching. This characteristic of the ore is a key in being able to profitably mine and process gold ore at an average grade of 0.69 grams of gold per tonne. Strict blasting control is also a key in success of the leaching operation. A system of splitting ore and waste in blast patterns has been devised to reduce dilution. Also, drill hole spacings are varied from 3m x 3m in breccia ore to 4m x 4m in syenite ore to 5m x 5m in waste. Drill holes

Jan 1, 1987