Search Documents

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By Barton J. Suchomel

Introduction Despite perennial economic turbulence, Argentina continues to push ahead with efforts to develop its fledgling hardrock mining industry. The country lacks the infrastructure and mining history of neighboring Chile, but contains vast areas of great resource potential. The eastern slope of the Andean Cordillera in west-northwest Argentina is a relatively little-explored region offering geology highly conducive to the occurrence of base and precious metals deposits. Past exploration has concentrated on locating and evaluating porphyry copper-molybdenum (Cu-Mo) type occurrences. Comparatively little attention has been given to precious metals potential. An interesting and important group of base and precious metals prospects in northwestern Argentina occurs within and adjacent to the Upper Miocene Farallon Negro volcanic complex in Catamarca province. The volcanic complex contains numerous base and precious metals vein occurrences, high gold porphyry copper prospects, and possible disseminated gold targets that have attracted relatively minor attention in the past. Various geologic aspects of the region have been reported by several workers (Llambias, 1970, 1972; Caelles et al, 1971; and Sillitoe, 1973). Regional geology The Farallon Negro volcanic complex is located within the Sierras Pampeanas morphostructural province about 200 km (125 miles) east of the main Andean Cordillera (Fig. 1). The Sierras Pampeanas is characterized by north-south-trending basin and range topography that developed during the Miocene and Pliocene. Uplifted blocks are composed mainly of lower Paleozoic metasediments and granitoid plutonic rocks unconformably overlain by Tertiary redbeds and minor carbonates. A consistent landward migration of volcanic and intrusive ac¬tivity occurred in this region of the Andes from the early Mesozoic through the mid-Tertiary. An eastward extension of magmatism during the Miocene and Pliocene resulted in the formation of the Farallon Negro volcanic center. Volcanism at Farallon Negro ini-

Jan 8, 1988

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007

By Mohamed Yusuff

Modern transportation systems are one of the most important achievements of our civilization and provide us with tools for broadening individual and social freedom of choice. The transportation system initiated today is handed dawn to the next generation, probably with little choice because of the enormous expenditure of monies involved, and influence their way of life as to where they should live and where they should work. The ever increasing antagonism between the citizens and the planners of the transportation systems necessitates a careful review of the entire planning process. The planning process can be broadly classified into: the goal formulation and decision making process; the plan development process; and the plan implementation process. THE GOAL FORMULATION AND DECISION MAKING PROCESS Goal formulation and decision making is one of the vital phases of the planning process and is primarily based upon social values. In measuring social values, the planner must employ an appropriate scale of measurement since in the absence of this yardstick, these values tend to became vague and abstract ideals. The need for major social programs and concerns (poverty, etc.) of the urban areas should be analyzed to determine the type of transportation system which would contribute to the solution.

Jan 1, 1974

By Adrian Molinari

A radioisotope probe (Minexan 202) capable of simultaneously analyzing a mineral slurry for five elements and pulp density has been developed by Outokumpu Oy, Finland. The probe is designed to operate immersed directly in a process stream, or it can be equipped with a flow cell through which passes a continuous sample of the main stream. A minicomputer (PDPII) is used to control the probes and calculate the assay data. This paper describes the probe as applied to slurry analysis and compares it to the conventional x-ray on-stream analyzer (Courier 300).

Jan 1, 1977

By A. Kevin Beaton, Robert W. Laakso

The desire for dry passageways promotes the NATM as it provides a final support system most suitable for the installation of a waterproofing membrane. Waterproofing during construction is a cost effective way to enhance safety and function as well as increasing the life of an underground structure. The NATM approach utilizes the surrounding mass as an integral element of the "ringlike" support system. At the Pennsylvania Turnpike Commission Lehigh Tunnel No. 2 various rock classifications were determined to require support measures ranging from 2 to 12 inches of shotcrete along with spiling, wire mesh, deformed bar, lattice girders and rock bolts as needed. Field instrumentation and monitoring programmes are a key factor for the success of the NATM. When the support "shell" stabilizes smoothing shotcrete, waterproofing and a final liner can be placed.

Jan 1, 1991

By Jacques F. Abrahamse, Kevin A. Bahe, T. Arthur Palm, Gregory E. McCluskey, Stephen L. Bessinger

Introduction Basis For System San Juan Coal Company (SJCC) is a subsidiary of BHP Billiton. Until recently, BHP Billiton operated three surface mines in northwestern New Mexico: Navajo, San Juan, and La Plata. The San Juan and La Plata Mines supplied the San Juan Generating Station operated by Public Service of New Mexico. Stripping ratios at those operations were increasing, and by 2000 a feasibility study was underway to develop SJCC’s vast underground reserves as a replacement. Early in the evaluation and planning phase for the San Juan Underground Mine, it was determined that the target seams (Fruitland #8 and #9) had a high propensity for spontaneous combustion. Spontaneous combustion was identified as a risk, both to personnel and equipment, and to the ability of SJCC to reliably fulfill its obligation to the power plant. In the last 20 years, several western US coal mines suffered underground spontaneous combustion events and/or mine fires. Included in this group were Colorado Westmoreland’s Orchard Valley Mine (1987), RAG’s Willow Creek Mine (1998 and 2000), Oxbow’s Sanborn Creek Mine (1999), the West Elk Mine of Arch Coal (2000), Arch’s Skyline Mine (2002), Western Fuels’ Deserado Mine (1996), and the West Ridge Mine of Andalex Resources (2003). The cause for the majority of these fires was spontaneous combustion. Fighting the fires required injection of an inert gas or foam. Nitrogen and carbon dioxide were the predominant choices of inert gas. In all cases, the gasses had to be trucked in from considerable distances. Before the inert gas could be used, injection holes had to be drilled into or near the suspected fire locations. This drilling and trucking caused costly delays in the timing of the fire fighting effort, and was not as precise as desirable. Emergency purchasing of gas and pumping services was extremely expensive, running as high as $70,000 per day at one mine. As a result of the experience of other western US coal operators, and the risk inherent with spontaneous combustion at SJCC, it was decided to pursue installation of a nitrogen delivery facility on-site at SJCC. This decision was later expanded to include a continuous supply of nitrogen.

Jan 1, 2005

By S. Cotten

The regulations for current coal mine refuge alternative (RAs) require that there be sufficient life support to sustain survival of the maximum number of RA occupants for a minimum of 96 hours. This minimum duration assumes that rescuers can access the RA through the mine within four (4) days of the onset of the mine emergency. But what if mine rescue teams cannot reach the miners within the RA before the RA air supply is severely limited or exhausted? What could be done to extend the duration of the RA life support capability into the 97th hour and beyond? In addition, what might be done to enable more rapid rescue of the miners if they could not be reached through the mine in a timely manner? This paper describes a systems approach to address the potential need to extend the duration of RA life support beyond current design limits. New capabilities that need to be developed in advance of such a dire need include more reliable emergency communications, highly mobile and efficient drilling rigs, enhanced directional drilling techniques, and a standardized RA external life support interface along with RA internal design modifications to accommodate use of an external supply. The following sections describe the need, intent, and technology gaps associated with each of these capabilities. Government agencies and the mining industry should consider initiation of a program to investigate, design, and develop effective means of extending the current 96-hour time restriction on coal mine refuge alternative life support. The development process should begin with a focused study to refine the overall operational concept, investigate the current state-of-the art of critical technologies, identify specific technology development priorities, and make recommendations for a development program to provide in an organized, efficient, and timely manner a solution for extended refuge alternative life support and occupant rescue.

Jan 1, 2011

By K. Zeidler, T. Schwind

The Fort Canning Tunnel, Singapore, is an approximately 50 feet (15m) wide vehicular tunnel under shallow ground cover that has been constructed according to the principles of the NATM. Its shallow location in soft ground combined with a high groundwater elevation in close vicinity of historically important features called for special design considerations combined with a rigorous monitoring scheme. Surface, sub-surface and in-tunnel instrumentation was installed to monitor the performance of the ground and tunnel support during construction. Comparison of actual reading data with the results from the computer modeling carried out during the design phase is provided in this paper.

Jan 1, 2007

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By M. J. Blattman

Upon completion of an underground mine design, the planning engineer is faced with a surprisingly complex problem, “What development and mining sequence should be implemented so as to maximize the return on investment?” The problem relates to the scheduling of development headings to access stope production areas in such a way that the most money is made as quickly as possible for as long as possible. The total dollar value of the stopes, the average grade, the total tonnage, nor even the profit margin do not accurately give an indication of the “proper” mining sequence on their own. This paper will outline a method being developed by the author that can create a sequence of events that maximizes the net present value (NPV) of a given development and production design using information already being generated during the design process.

Jan 1, 2003

By R. E. Moore

Refractories are unique ceramic materials, which are used in large quantities in steel making furnaces, metal smelting vessels, and glass melting tanks. They are required to possess high thermal shock properties and good slag corrosion resistance as well as creep resistance at high temperatures. Therefore, they are made from very refractory minerals such as lime, periclase, corundum, spinel, and zirconia. Slags are vitreous materials produced as a residue in steel refining processes. They cover a wide range of compositions and may contain pure oxides, silicates, and sulfides as well as fluoride phases depending on the melting and smelting processes. These minerals exhibit spectacular cathodoluminescence color under electron bombardment; therefore, cathodoluminescence (CL) microscopy is found to be a superior technique for the characterization of refractory corrosion by slags. Examples included in this study are (1) reaction of fluorine containing mold slags with ZrO2-C nozzle refractories promoting crystallization of the Cuspidine, Ca4Si2O7(F,OH)2, (2) corrosion of fusion cast refractories in TV panel glassmaking furnaces and formation of glass defects, and (3) reaction of spinel based castable refractories with copper smelting slags.

Jan 1, 2001

By Jamal Rostami, Levent Ozdemir, Amund Bruland, Filip Dahl

Cerchar Abrasivity Index (CAI) is one of the commonly used tests to evaluate rock abrasiveness for cutter life/cost estimations of TBM projects. There are at least 3 style machines, 2 different pin hardness, and the test could be run on fresh rock surface VS a sawn surface. Each of these parameters has a meaningful effect on the results, but its impacts were not fully understood nor its implications well explored. This paper reviews the current practice of Cerchar testing and its implications on geotechnical investigations related to TBM tunnels and provide a set of guidelines on testing and reporting of the test results for future projects.

Jan 1, 2005

By S. E. Pérez-Fontes

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. The oxygen concentration in the process gas was set to 40% and 70% (by volume) and a heating rate of 40°C/min was used. Response variables included the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles and by thermochemical and mass balance calculations to reproduce the DSC and TGA data. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction as a function of time.

Jan 1, 2007

By Laura McNally

In 2006 McNally International Inc. in a Joint Venture partnership with Aecon Constructors was the successful bidder on two York Region Tunnel Projects: Bathurst Collector/Langstaff Trunk Sewers; and YDSS Interceptor Sewer 19th Avenue Project. These projects comprise a total of 13 kilometres of 2.74 meter finished diameter tunnels and are both part of the York Durham Sewer System (YDSS). Both contracts require the use of EPB tunnel boring machines with a precast concrete segmental liner. The following provides an overview the two projects.

Jan 1, 2008

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

By K. Donahue

Clay minerals play an important role in the gravitational stability of man-made rock piles by affecting geotechnical and hydrological characteristics of the material. The Goathill North rock pile at the Questa Mine in northern New Mexico has been the focus of a multi-disciplinary study to determine the effect of weathering on rock pile stability and in particular to determine if clay minerals are forming in the rock pile due to surface weathering. The results of x-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses indicate the clay minerals found within the fine-grained soil matrix of the rock pile are of hydrothermal origins and did not detect any neoformation of clay minerals. The foremost mechanism for an increase in clay minerals within the rock pile is the physical break down of hydrothermally altered rock fragments to release hydrothermal clay minerals. The hydrothermal clay minerals within the rock pile show evidence of weathering by the dehydration of smectite from 2-water to 1-water interlayers within the clay mineral structure. This dehydration is most likely due to higher temperatures and low relative humidities in the Goathill north rock pile during surface exposure.

Jan 1, 2009

By C. Arthur Lefler

The hydrometallurgical processes for recovery of gold and silver in use at Round Mountain, Nevada and the practical aspects of the operation are discussed. Included are heap leaching by cyanidation, upgrading of solutions by adsorption of values on activated carbon and desorption (stripping) for electrowinning and subsequent refining steps to produce dore metal.

Jan 1, 1981

By Shamim A. Dar, & Samsuddin Khan, & K. F. Khan, Mohd Shuaib

The Late Paleocene–Middle Eocene phosphate nodules of Solan District of Himachal Pradesh belong to green facies of Subathu Formation of Sirmur group. Field observations indicate sporadic distribution of phosphatic nodules in the yellow brown to rusty brown, buff-colored bleach shales. Phosphatic nodules are dull earthy to dark grayish in color and break with sharp and conchoidal surfaces. Studies of phosphatic nodules using petrological microscope, X-ray diffractometry, and scanning electron microscopy (SEM) attached with energy dispersive X-ray (EDX) reveal that cryptocrystalline apatite (fluorapatite) is the dominant phosphate mineral. Silt sized silica is the dominant gangue, whereas pyrite and muscovite are present as minor gangue. The phosphate minerals occur as oolites, pellets, and cryptocrystalline apatite in the groundmass. Silica veins form a network replacing the original phosphatic matrix. Brown to brownish black color may be attributed by the organic matter in the phosphatic nodules. Completely phosphatized radiolaria and partially pyritized planktonic foraminifera are observed. There is corroboration of organic matter in the form of microbial filaments in the groundmass of apatite. The findings in the present investigation indicate that the different forms of the minerals, their texture, and distribution in the phosphatic nodules might be due to environmental vicissitudes in oxidizing to reducing conditions followed by replacement processes. Presence of microbial filaments may be due to the active role of microorganisms during the formation of these phosphatic nodules.