Search Documents

By S. K. Kawatra, V. Claremboux, S. Valluri

Carbon dioxide capture from coal-fired power plant flue gas and subsequent sequestration is expected to play a vital role in mitigating global climate change. To meet the growing need for CO2 capture Technology, Michigan Technological University is researching CO2 capture and Utilization. We have successfully converted CO2 into oxalic acid using an electrochemical approach. If oxalic acid can be produced in bulk from CO2, it can be used to leach rare earth minerals at low cost. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. In this paper, we will present an idea of how the factors mentioned above will effect the electrochemical reduction of CO2 to Oxalic acid. INTRODUCTION. CO2 is thermodynamically quite stable, as shown by its highly negative heat of formation. Thus, it is expected that the formation of any useful chemical from CO2 will require the input of at least as much energy as geological sequestration. However, to be more effective the resulting economic value of the chemical need only pass the cost of the additional energy required beyond geological sequestration. This lends itself to two extremes: one where the quantity of energy required is low and one where the economic value of the additional energy is low. It is expected that CO2 can be reduced via electrolysis to several compounds. Of particular interest are formic acid, oxalic acid, methanol, ethanol, formaldehyde, and carbon monoxide (as a component to syn-gas). These chemicals have been reported as electrolytic products previously in literature and have considerable potential for application. EXPERIMENTAL Electrocatalytic Production of Oxalate from CO2 We are using membrane electrolysis cell to produce oxalate from CO2. A membrane electrolysis cell is a 2-chamber electrolysis cell where the chambers are separated by a selectively permeable membrane. To produce oxalate, a cation exchange membrane (which selectively exchanges cations) was used. Previous literature suggests that in the cathode chamber an organic electrolyte, such as tetraethylammonium perchlorate or tetraethylammonium bromide in dimethylformamide, are preferred3. In the anode chamber, a sodium hydroxide solution water is used. Carbon dioxide is then bubbled into the cathode chamber as a current is applied.

Jan 1, 2019

By Carrie Smith

In 1972, in Denver, CO, five women with a shared goal joined forces to create the first formal space for women in the mining industry: Women in Mining USA (WIM USA). When the organization first took shape, few could have predicted that a small gathering of women would grow into one of the most influential organizations that would advocate for inclusion in the industry. Now, more than 50 years later, the group remains a vital network for professionals across the United States with a diverse array of membership and chapters.

Jan 1, 2026

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By M. Laliberte

"Gold-mine effluents are often characterized by high concentrations of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While not acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be nonlethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25°C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.IntroductionThis paper will demonstrate that gold-mine effluents, which are toxic to fishes and invertebrates, can be made nontoxic by using a combination of chemical precipitation and biological oxidation.The typical composition of gold-mine effluents will first be described. The applicable legislation will then be introduced, with its requirement that the treated effluent be nontoxic. The toxicity of a typical untreated effluent will then be confirmed, and the sources of the toxicity identified. After that, a number of toxicity reduction treatment methods will be presented, and the selected method will be described.The lab tests that confirmed the efficiency of the treatment method will be presented, with three phases of testing as the understanding of the process gradually improved. Toxicity test results showing that the water is nontoxic after treatment through the temperature range will be presented."

Jan 1, 2015

By B. V. Knelson

Although the concept of centrifugal recovery has been around in one form or another for many years, it has not been until recent times that it has became clearly understood am properly put into perspective. Simplistic in theory, it is when one begins to examine the variables involved that the true complexities of this matter begin to emerge. In creating an enhanced g force concentrator, there are many aspects both positive and negative that are encountered.

Jan 1, 1989

By R. M. Hernandez

The Bureau of Land Management (BLM) constructed four passive biochemical reactor systems (BCRs) to treat mining influenced water (MIW) in the Bunker Hill Superfund area near Coeur D?Alene, Idaho between 2002 and 2003. Initially, the BCRs operated very effectively. However, in the past couple of years, the zinc removal effectiveness of the four BLM BCRs has declined [1]. The central objective of this study was to characterize the microbial communities and substrate present within the BLM BCRs and to use these factors to propose strategies to promote sustained sulfate reduction levels. Microbial communities were characterized by quantifying total bacteria and sulfate reducing species. Substrate was characterized by quantifying the percent organic, acid soluble organic, acid insoluble organic, and bioavailable material within the BCR. The results suggest the depletion of bioavailable organic substrates is the primary cause of the decline in zinc removal and not the microbial community structure. The ability to assess the amount of bioavailable organic substrate and microbial community is important to the understanding of the sulfate reducing capacity of the BLM BCRs and developing strategies to facilitate performance enhancement of the current BLM BCRs. The characterization of organic substrate and microbial community structure are also important to improving design of future passive treatment systems for mining influenced waters.

Jan 1, 2010

By L. P. Meade

The need to feed an established talc mill from a crude are source located closer to the mill prompted the drilling in 1986 of a previously mapped talc-carbonate deposit. This talc-bearing rock had never been considered as a potential source of crude talc are because of the high carbonate content and other deleterious minerals that were observed in outcrops. Selective mining, in-pit grade control and creative processing has allowed this deposit to be developed into an orebody. By definition, an orebody has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by are tenor.

Jan 1, 1992

By F. L. Jackson

The large scale transportation and storage of sulphur in the liquid state is a relatively new development, but is really only a logical extension of old mining and processing techniques, It is not known who the first person was to win a relatively pure sulphur from ore by melting, but this method was commercially used at least two hundred years ago in Sicily and is still in use today. The Frasch process of mining was invented over sixty years ago, and the development and improvement of-liquid sulphur pumping and handling techniques has paralleled the growth in the Frasch mining industry. During the last fifty years, improvements in the technology of using sulphur have included the premelting of sulphur prior to its being burned for acid production or conversion into CS2 and other compounds. Yet, until fairly recent times, sulphur produced as liquid has been solidified into large blocks at the producing point, broken down by blasting or with mechanical equipment, and shipped in bulk form as a solid.

Jan 1, 1962

By Evangelos Spyridonos, Thomas Frommer, Wolfdietrich Skala, René Prissang

Operational grade modelling is a technique that uses production data to run daily updates of property models. It will enable mining engineers to use property predictions based on the most recently acquired data as support for quality control and decision making. The approach necessitates that the properties of the run- of-mine material can always be attributed to individual mining blocks or charges. The software employed must be highly reliable, because a system failure or the loss of data could seriously affect the mine's quality management. An operational grade modelling system has been developed for the Breitenau magnesite mine. It makes use of the Linear Octree Based Property Modelling system which was conceived and realised at the Free University of Berlin. This paper describes the system design and gives an account of the experiences during the first six months since system start-up.

Jan 1, 1996

By Lukas Erkurt, Wolfgang Holzer, Stefan Auderer, Richard Gradnik

SEM/ NATM Tunnelling contracts in Austria and Germany are usually tendered applying unit price contracts. The purpose of this paper is to show how contractual problems are resolved in these countries. The focus will be put on describing the theoretical approach, several case studies will show how contractual problems were dealt with on site.

Jun 23, 2024

By J. R. Henke

Dewatering wells producing iron-rich water experience rapid declines in yield and drawdown due to the formation of ferric (Fe +) hydroxide deposits in well screen, pump intake and riser pipe. Precipitation is caused by a combination of dewatering-promoted iron oxidation and iron-oxidizing bacteria. Physical and chemical well rehabilitation techniques, as well as alternative well construction and well development techniques designed to minimize well clogging, were evaluated in this study. The addition of acid downhole feed systems to dewatering wells prone to iron encrustation can, in some cases, prolong their operational lives up to 500 percent that of unacidified wells.

Jan 1, 1989

"A commercially available through-the-earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electricfield (E-field) sensing to send text-based communications through two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivities. IntroductionWireless, through-the-earth (TTE) communication technology is designed to achieve point-to-point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. Using this approach, communications are established without the need for intermediary communications infrastructure. As a result, TTE systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers, 1924; Pittman, Church and McLendon, 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon, 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker, 2006; Wadley, 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer, 1973; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Jakosky and Zellers, 1924; Large, Ball and Farstad, 1973). Although commercially developed TTE systems have demonstrated the ability to communicate in a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker, 2006; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Ilsley, Freeman and Zellers, 1928; Jakosky and Zellers, 1924; Yenchek et al., 2012)."

Sep 1, 2016

By John M. Smith

Kaolin is an important industrial mineral because of its unique properties and low cost. Strictly defined, kaolin is the name given to a group of hydrous aluminum silicates of which kaolinite is the most common mineral (1). Through common usage the mineral, kaolinite, is called "kaolin" or "china clay". In 1972 over 4, 000, 000 tons of kaolin will be beneficiated and shipped by domestic producers. By far the largest user of kaolin is the paper industry which utilizes approximately 65 to 70 per cent of the total production. Kaolin is used in paper as a filler in the interstices of the sheet and as a coating to impart smoothness, gloss, brightness, and printability to the paper. The rubber industry is also a large user of kaolin where it is used as a filler because it adds strength, abrasion resistance, and rigidity to both natural and synthetic rubber goods. Kaolin is used as an extender in paints because it is chemically inert, has a high covering power, gives desirable flow properties, and is low in cost. In ceramics, kaolin is used in whitewares, tile, insulators, refractories, and in some face brick where a white color is desired. Kaolin is also used extensively in plastics as a filler in thermosetting and thermoplastic mixes to give smoother surfaces, a more attractive finish, good dimensional stability, and resistance to chemical attack. Many other process industries use kaolin as a filler, suspending medium, or for color improvement.

Jan 1, 1972

By J. D. Vincent

The Henderson mine site is located at Red Mountain on the eastern slope of the Rocky Mountains, approximately 50 miles west of Denver, Colorado. The mill site is on the west slope of the Rockies and mine and mill will be connected by an underground railroad. All designs were for a 30,000 ton per day molybdenite processing plant with provisions for future expansion up to 50,000 ton per day if required. This plan did not just happen, but slowly evolved over the course of about three and one-half years. Many plants cannot afford such a delay, but the Henderson project will take about 10 years from the time it was first discovered until production starts, and these 3 !1 years were well spent in determining the best possible plant site and flowsheet. This paper describes some of the problems and the decisions made in arriving at the final location and flowsheet. The paper does not go into the specific details of how protection of the environment went hand-in-hand with all other project considerations. This particular aspect of the planning has been well-reported on other occasions and considerable information on it is readily available.

Jan 1, 1972

By Joan Carles Casado Ortega, Mitchell Gerdtau, Sandeep Pyakurel, Eric Crocker, Frank Perrone

The Parallel Thimble Shoal Tunnel (PTST) project is a part of the Chesapeake Bay Bridge- Tunnel (CBBT) complex. The project involves the construction of a two-lane bored tunnel under the Thimble Shoal Channel between Portal Island #1 (the southernmost island) and Portal Island #2. The new PTST will be the rst transportation tunnel constructed in the Mid-Atlantic region by a tunnel boring machine (TBM). This paper describes the design and construction of the tunnel approach structure in an open marine environment with the strategies employed to overcome the various construction challenges. The project is unique since the entire tunnel approach structure is built on a very limited area within an open marine environment without any reclamation of the existing island.

Jun 23, 2024

By Z. R. Llanos

The petroleum refining industry makes extensive use of catalysts for the conversion of crude oils into more usable products such as gasoline, fuel oil and gas, aromatics, and others. Catalysts used for hydraprocessing contain cobalt-molybdenum or nickel -molybdenum, although there are catalysts that also contain tungsten. During hydroprocessing, nickel and vanadium are deposited on the catalysts, eventually rendering them inactive. The refiners are then confronted with the problem of disposing the spent catalysts. In the past, landfilling was a common method of disposal and it is still practiced in some countries. Other refiners prefer to stockpile the spent catalysts at the refineries until the price of metals warrants their sale to metal reclaimers. This practice, however, poses environmental problems to the refineries for storage and disposal of spent catalysts. Other types of catalysts are amenable to regeneration. The purpose of this paper is to focus attention on the recovery of nickel, cobalt, molybdenum, vanadium, and alumina from spent hydroprocessing catalysts by Gulf Chemical and Metallurgical Corporation and to review the use of sodium hydroxide and sodium carbonate for pressure leaching of spent catalysts.

Jan 1, 1986

By H. S. Castro

The by-product molybdenite technology in Chile is reviewed. Flowsheets, reagents and some operation features for the actual six Chilean moly plants(Chuquicamata, El Teniente, El Salvador, Andina, Las Tortolas and Pelambres), are presented. The chemical and physicochemical factors involved in the depression of copper and iron sulfides during the selective flotation of molybdenite, with sodium sulfide, sodium sulfhydrate, anamol-D and LR-744, are discussed. Advances in technology to solve problems of excess of lime (precipitation with sulfuric acid); excess of residual flotation reagents (activated carbon and kerosene); and optimization of depressant consumption (Eh control, nitrogen and low-oxygen air), are discussed.

Jan 1, 1998

By K. V. Viswanathan, P. Sornasundaran, S. E. El-Mofty

Dolomite is found to undergo preferential dissolution in aqueous solutions and this is found to be strongly dependent on the solid to liquid ratio (SIL). Electrokinetic studies done under the sump conditions revealed that the mineral surface charge is also affected markedly by the solid content in the suspension. Conditioning of the dolomite at low SIL ratios for short time intervals showed preferential dissolution of calcium leading to a magnesium-enriched dolomite surface. At higher SIL ratios and longer conditioning times, calcium depletion from the solution and a calcium-enriched dolomite surface resulted. The results are discussed in terms of surface precipitation and/or bulk precipitation and surface conversion of dolomite to the calcium-enriched phase (calcium carbonate and/or magnesian calcites).

Jan 1, 1990

By K. W. Lentz

The Maybell Mill of, Trace Elements Corporation, Unit of Union Carbide Corporation is located approximately five miles northeast of Maybell, Colorado, and twenty-five miles northwest of Craig. It is located in the midst of the uranium ore deposits whose presence, made it possible. In November 1953 Russel Cutter, Chief Geologist for the original Trace Elements Corporation, picked up high readings on a scintillometer while flying over this area. Later, with George Morehouse, Chief Engineer for the original. Trace Elements Corporation, he started a search for surface indications. In this search, they found an out crop which can be regarded as the discovery lode on this property. The actual locating of claims and acquiring free lands and state lands was begun in March 1954. During 1955 enough drilling was done to indicate that a sufficient tonnage of ore existed to make possible a mill. These ore deposits are located in the Browns Park formation which is an unconsolidated sandstone with a few hard lime ribs running through it. The geologists tell us that this region was once a vast basin which became filled with wind blown sand and volcanic tuff, Later on, ground waters brought uranium into the basin which precipitated out in the sand. During the late summer and fall of 1955, a small pilot plant was operated under the supervision of John L. Chapman testing these Browns Park ores. During the operation of the pilot plant, three small open pits were developed and the ore from these pits shipped to Union Carbide Nuclear Company, Division of Union Carbide Corporation, at Rifle. To date all ore is being mined from open ptis. In the fall of 1956 the original Trace Elements group signed a contract with: the AEC for a mill at Maybell and on November 5, 1956, Union Carbide acquired the Trace Elements Corporation properties and contract. During the next two months, intensive research was carried out on the Browns Park ores by our research lab at Rifle. They also checked some of the metallurgical results which had been obtained through the operation of the pilot plant by the original Trace Elements group. During this period, a report on Trace Elements Corporation ores was also prepared by the Colorado School of Mines Research Foundation. This report contained data on representative samples of the ore tested for the original Trace Elements group. From this research and study a flow sheet was decided upon.

Jan 1, 1959

By R. L. De G. Solms

INDEX 1. INTRODUCTION 2. FLOODING 3. THE PLUG 4. THE FIRST ATTEMPT 5. THE SECOND ATTEMPT 6. PUMPING 7. TIGHTENING OF THE PLUG 8. SHAFT REPAIRS 9. POST-MORTEM 10. CONCLUSION

Jan 1, 1987