Search Documents

By Andrew Chegwidden, Tara Wilk

Shaft 18B-1 is the second shaft to be constructed as a part of contract C547A along the New York City water supply system Tunnel No. 3. More complex than Shaft 17B-1, this site has an additional 30 m (100 ft) of overburden for a total excavation depth of approximately 78 m (256 ft) through water-bearing overburden soil and 145 m (475 feet) of gneiss bedrock to connect to the underlying Water Tunnel No. 3. round freeing was specied as the method to provide temporary earth support and ground water control for the overburden material. An extensive supplemental geotechnical investigation (SGI) and frozen soil testing program was performed to develop the design of a temporary ground freezing system, consisting of over 7,315 m (24,000 ft or 4.5 miles) of drilling for the installation of 95 freeze pipes. At the start of shaft excavation, the upper sandy silts strata was found to have an unprecedented low thermal conductivity, leaving the frozen soil face approximately 0.6 to 1 m (2–3 ft) behind the cutline. The ground freezing earth support needed to be augmented with ring beams and liner plates to support this soil face and allow for the excavation to proceed and be completed safely.

Jun 23, 2024

By G. W. Leney

Introduction and Historical Background The office and mining operations of Pacific Asbestos Corporation are located near Copperopolis, California in the foothills of the Sierras about fifty miles east of Stockton. This is historic country in the heart of the old Mother Lode gold district. Mark Twain's famous story of the jumping frog, written here, is still commemorated in an annual contest in Calaveras County,' and the camp at Poker Flats, described by Bret Harte, was only a few miles from the present mine.2 Joaquin Murrieta, the famous Mexican bandit started his three year reign of terror in this vicinity,3 and Black Bart, the P08 laureate of the stagecoach robbers, held up his first stage at Funk Hill, just three miles north of the mine. His last robbery was at almost the place, on the top of the hill overlooking the Stanislaus River ferry crossing. Although this was his favorite country, and he traveled extensively through it, he was not a credit to his acclaimed profession of Mining Engineer because there is no evidence that he ever recognized the asbestos, and he was finally caught as a consequence of the robbery at the ferry.4 One of the old stagecoach roads crossed the Stanislaus River at the mine site, and the ferry landing may still be seen from the main haul road into the pit. The road itself is partly buried under the rock dumps. In spite of its location and apparently prominent exposure, the first work on the asbestos deposit was not recorded until 1904.5 Development of the present operations was started in 1959 by Jefferson Lake Asbestos Corporation, a subsidiary of Jefferson Lake Sulphur Company. Management control of the company changed hands several times and it was later reorganized under the name of Pacific Asbestos Corporation. In December, 1968, a controlling interest was acquired by H. K. Porter Company, Inc. Figure (1) shows the mill and office buildings as seen from a site near the entry road. The offices are at the left with the mill warehouse in the foreground. The conveyor at left center carrys mine concentrates up the hill from the crusher. In the background are the dry rock storage building and mill tailings piles. Since the beginning of mining operations in 1962, seven and three-quarter million tons of ore and fifteen million tons of waste have been removed from the open pit which now measures about 1400 x 1800 feet at its widest points. The lowest operating level is at an elevation of 726 feet about 325 feet below the original surface. Figure (2) shows the open pit looking toward the west end. The main haul road can be seen along the side of the pit. A shovel is operating at the bottom of the pit while a front end loader on the level above provides ore for blending. In the background are rock dumps for waste stripping. The company markets an annual production of 30-35,000 tons of chrysotile fibre in groups 4 through 7, under the Mother Lode Brand

Jan 1, 1972

By M. Poulton, J. A. Botín, C. Gatica

"The Chilean minerals industry faces a shortage of 27.000 new skilled professional by 2023. Enhancing the integration of women into the workforce is a possible solution. This study analyzes the state of women in the mining workforce over the past decade. Several key indicators are presented: percent in the workforce, salaries, career profiles, presence at management level, and participation in academia are studied. The study also analyzes the strategies used by government, industry, and universities to recruit and retain women for the minerals industry. The main results show that women represent 7.4% of the mining workforce in Chile and less than 1% of senior positions with a salary gap of approximately 30%. Systematically, women prefer professional programs in geology, chemistry, and environmental areas. The Chilean statistics are compared to data from the United States mining industry. INTRODUCTION The Chilean mining industry faces a significant shortage of professionals for the next decade which compromises competitiveness and productivity. The demand for human capital in mining depends on several factors. First, the age structure of workforce, which determines future retirement needs. Second, minerals market considerations, determining the amount and size of mining projects entering production in the coming years. Third, the evolution, positive or negative, of productivity, mainly driven by technology and innovation, and negatively affected by the declining ore grades. Finally, negative trends in lead times to production of mining projects, due to social opposition, changing regulations and other project contingencies, negatively affecting the demand for human capital. Regarding the supply of human capital, the fast increase in the technology level of the minerals industry and hence, the increase of technical qualification requirements of the human capital generates a rise in the time required for trade and university education of mining professionals, which may cause imbalances in the labor market. According to (Consejo Minero, 2014) human capital gap in Chile by 2023 will be around 27.000 workers for extractive, processing and maintenance jobs, which represents 14% of the current workforce (Figure 1)."

Jan 1, 2016

By S. Tan

In this paper, several commonly used computer truck dispatching criteria are evaluated. A computer-oriented truck dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics, and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. All basic dispatching criteria including minimizing truck waiting time, minimizing shovel waiting time, minimizing truck saturation, maximizing truck momentary productivity, or truck routes optimization provide a local optimal solution. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely. Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. However, based on the simulation results of the mine operation, several dispatching criteria which have good potential to increase performance can be selected. It may be necessary to search for the best combination of these truck dispatching criteria for a given situation. For example, a truck flow measurement such as the truck clustering factor at shovels can be used as a switch parameter to change from one criterion to another. The values for the switch parameter at which actions should be taken to change the criterion can be established through simulation programs.

Jan 1, 1992

By Stanislatv Pawlowski

New, large sulphur deposits were discovered in Poland in 1953, the result of investigations by the National Geological Institute. All deposits occur in a widespread Miocene evaporite unit in the Carpathian foredeep. The gypsum underlying impermeable Sarmatian clays was altered to limestone and native sulphur where penetrated by hydrocarbons and bacteria. All deposits occur in Miocene structural uplifts. The early determination of the genesis of the sulphur deposits and their occurrence in elevated blocks led to an exploration program that successfully located new deposits.

Jan 1, 1978

By Rollien R. Wells

The Bureau of Mines was created in 1910 by an act of Congress and subsequently directed to: "...conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment, and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources through the prevention of waste ..." Under this broad charter, the Bureau's responsibilities have changed and grown from an almost exclusive concern with coal and coal mine safety to the present emphasis on a full spectrum of mineral producing and consuming problems. In the past 30 years, the domestic consumption of coal, oil, gas, metals, and industrial minerals has more than quadrupled, in parallel with the rapid and enormous growth in industrial production. Of the scores of metals and nonmetals essential to the Nation's progress and security, many are scarce and difficult to wrest from domestic sources. Reserves of some ores are dwindling. Available ore resources are becoming leaner and more difficult to treat. In recognition of this many faceted problem, the Bureau has engaged in a continuing quest for new and improved technology to enable economic exploitation of marginal minerals and fuels, to find substitutes for minerals in short supply, and to create better materials to meet the expanding and diverse requirements of the growing economy. The current central concern of the Bureau is focused on meeting projected fuel, metal, and mineral demands at the lowest real cost by recovery from available resources by new and improved technology that minimizes waste, hazards, and social and environmental problems.

Jan 1, 1970

By Marc Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molbydenum and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper price; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1980

By R. A. Seitz

This paper presents a framework for analyzing the theory and industrial practice of coal flotation and gives some examples of its use for understanding flotation phenomena and optimizing/controlling flotation circuit performance. It is based on extensive laboratory and in plant test work conducted over the past several years by researchers at MTU as well as an analysis of the literature. Previous researchers have usually considered either the surface chemistry or the kinetics of coal flotation behavior, only rarely have these factors been considered together. However, these factors must be considered together in order to gain a clear understanding of the theory underlying coal flotation such that its practical application can be optimized. Fortunately, this complex objective can be achieved by considering the recovery and rate of recovery of the different types of particles present in the feed to coal flotation circuits and the fundamental mechanisms responsible for these recovery phenomena. The influence of three major groups of variables must be considered: control variables (reagent additions, aeration rate, etc.); disturbance variables (feed pH, percent solids, etc.); and circuit design variables (number of cells, circuit arrangement, etc.). Each of these groups of variables affects process kinetics in a clearly understandable manner, which, once determined, is extremely useful in circuit design and optimization. This paper includes a discussion of the use of the proposed framework to explain the effects of some coal characteristics on flotation performance. In addition, an example of using this analysis to optimize the performance of a coal flotation circuit using frother and collector addition levels is included.

Jan 1, 1985

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL

The steepness of an openpit mine’s slopes has a substantial influence on the mine’s financial return. This paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice, pitwall profiles are often planar in cross section within each rock layer: that is, the profile inclination across each layer tends to be constant. Here, instead, a new geotechnical software, OptimalSlope, is used to determine optimal pitwall profiles of depth-varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and factor of safety (FoS).

By Bo R. Arvidson

High-energy product permanent-magnet materials of rare-earth cobalt alloys are being used in applications where space or weight are at a premium cost. New applications like friction-free bearings are also made possible. However, such magnet materials have not been commercially used in magnetic separators until now due to the high cost for the overall magnetic flux generation relative to commonly used ceramic magnets or AlNiCo magnets. The design of the new high-intensity permanent- magnet roll separator (PERMROLL) takes advantage of the unique properties of rare-earth cobalt magnets rather than just substituting for conventional magnet materials now in use for magnetic separators. Hence, the new generation of high-intensity magnetic-roll separators has some unusual characteristics that make known magnetic separation applications more economically attractive, and even expands the magnetic separation technology area to include applications for which no other feasible methods are presently known.

Jan 1, 1983

By C. W. Schultz

The Alabama tar sands of the Hartselle Sandstone formation present a more difficult problem in primary extraction than do the Athabasca tar sands. In contrast to the Athabasca tar sands, the Alabama tar sands are "oil wetted" and the contained tar, or bitumen, is of much higher viscosity. A physical beneficiation scheme was developed in which clean sand from an external source was used as a scrubbing medium. High intensity scrubbing liberated the tars which are readily recovered by froth flotation. Locked cycle tests have shown that, after the use of an initial ration of clean sand, the system produced enough new clean sand to be self sustaining.

Jan 1, 1992

By Felipe Calizaya, Sekhar Bhattacharyya

Noise-induced hearing loss (NIHL) is prevalent in mechanized underground mines. Federal regulations are often not complied with effectively. Miners are also prone to ignoring administrative guidelines and/or personal protective equipment for hearing conservation. As a result, quality of life among experienced miners plummets while occupational risks increase at workplaces. This research focused on auxiliary fans used in underground mines. These fans work at high rotational speed and generate extremely high levels of noise in close proximity to miners. Silencers used are often of little effect due to poor maintenance. A new silencer is tried in the laboratory with the objective of easy maintenance and resulting reduction of noise exposure for miners.

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By Dr. Jagdish C. Agarwal

Kennecott Copper Corporation has developed a new hydrometallurgical process for extracting nickel, copper, cobalt and molybdenum from maganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 C to 50 C and has been successfully demonstrated in a continuous pilot plant processing 800 lbs of nodule ore per day. The chemistry, basic flow sheet and operating characteristics are presented and discussed.

Jan 1, 1978

By Paul M. Jr. Musgrove, Donald C. Moore

Conventional Smelting Practice Conventional copper smelting practice varies from smelter to smel¬ter, but generally consists of some or all of the following unit processes: roasting, smelting, converting, and fire refining. Roasting. Copper sulfide concentrates can be smelted directly or after an initial roasting step. Roasting is used in some smelters because roasting prior to smelting increases smelting capacity, less energy is required to melt hot roaster calcines than wet sulfide concen¬trates, roaster off gases are high in Sot concentration, 5-15% SO2, and some volatile impurities are removed from the concentrate prior to smelting. However, many smelters do not use roasters, because the problems associated with handling hot dry calcines outweigh the advantages mentioned. Concentrate roasting is performed in multiple hearth or fluid bed roasters. If the moisture is low, roasting can be performed autogenously, usually at 500-600°C. High roasting temperatures are avoided because excess oxidation of the iron compounds may lead to magnetite formation. Magnetite is detrimental to reverb operation because mag¬netite can combine with refractory minerals to form a highly viscous slag. This slag prohibits efficient matte-slag separation and leads to excessive copper losses. Also, magnetite can settle through the matte layer, deposit on the furnace bottom, and consequently reduce furnace capacity. Roasting is carried out only on sulfide concentrates prior to smelt¬ing in reverb or electric furnaces. For smelting processes, such as the flash and continuous that rely on the exothermic heat of oxidation of the sulfur minerals, roasting is not practiced. Reverberatory Smelting. The predominate copper smelting fur¬nace for the past 50 years has been the reverb. These furnaces are typically 100-120 ft long, 30-35 ft wide, and 12-15 ft high. A typical furnace layout is shown in Fig. 2. Refractory brick linings cover all internal surfaces of the furnace. Originally the flame was directed to reverberate or reflect off the furnace ceiling and melt the feed material. Current practice is to direct the flame down the furnace length to melt the concentrate. A method of charging the concentrates or calcines, generally along the side walls to minimize refractory erosion, is incorporated in the furnace design. The copper concentrates, calcines, and fluxes charged into the reverb undergo a series of complicated reactions as the temperature of the mixture increases. The reaction of the iron and copper sulfides with the oxygen in the furnace produces a molten Cu25-FeS mixture called matte. Copper smelting metallurgy is based on the fact that sulfur has a greater affinity for copper than for iron and most other common metals. Therefore, in a system containing copper, the copper will preferentially remain as a sulfide compound until all of the other metals have been oxidized. The oxidized metals combine with silica to form a silicate slag that floats on the matte and is removed from the system. Reverberatory furnace smelting chemistry can be approximated by the following chemical equations: FeS2 + O2 - FeS+ SO2 (1) The formation of FeS ensures that any copper present other than as sulfides will be reduced by the relationship: CuO2 + 2FeS + O2 - CuS + 2FeO+SO2 (2) or 2Cu +FeS - Cu2S + Fe (3) As the molten charge travels down the furnace, continued oxida¬tion of the iron minerals and sulfurization of the copper minerals occurs. When all of the copper has been converted to sulfides, the iron sulfides can then be further oxidized as: FeS + (3)2 O2 FeO + SiO2 (4) The FeO reacts with the silica added as flux in the furnace charge. A simplified equation is: FeO + SiO2 -FeO SiO2 (5) The iron silicate slag formed is skimmed from the surface at the end opposite the burners. The copper content of reverb slag is usually less than 0.6% Cu and is discarded. Matte is removed along the side wall and is taken to the converter for oxidation of the remaining sulfur and iron. The main objectives in reverberatory smelting are to produce a molten Cu2S-FeS matte containing 30-60% Cu and a throwaway slag. Production of matte permits complete conversion of all copper minerals into copper sulfides, which can migrate because of specific gravity differences, through the lighter slag layer. Also, the molten matte droplets collect the noble metals, gold and silver, as the matte settles in the furnace. The large settling area of the furnace provides enough separation time to produce a low grade slag, which can be discarded without further processing. High heat losses are associated with reverberatory smelting be¬cause of the large volume of gases sweeping through the furnace. Therefore, an outside source of heat is required to keep the smelting reaction going. Natural gas, fuel oil, or pulverized coal are used as this heat source.

Jan 1, 1985

By William H. McLemore

Geologists searching for carbonate rocks suitable for chemical uses traditionally have relied on extensive laboratory testing in order to locate strata or zones that might be suitable for mining. However, when considering the significant time and costs involved in sampling and performing chemical analyses, any exploration technique whereby fewer samples and analyses are needed would be of great value. In other words, if the exploration geologist could "zero-in" on select areas, considerable time and money could be saved. In general, the major-element chemistry of carbonate rocks is determined by the abundance of the minerals present. CaO occurs with CO2 as the mineral calcite, which is the primary mineral comprising allochems, matrix and sparry cement; MgO is found in high-magnesium calcite (many calcite fossil species contain appreciable amounts of MgO in solid solution), dolomite, and chlorite; iron occurs in pyrite and in limonitic stylolites, as well as in chloritic and glauconitic clay minerals; materials containing abundant Si02 are microcrystalline quartz (chest) silt-sized quartz, and clay minerals; and Al203 is found primarily in illitic, kaolinitic, and chloritic clay minerals. The presence or absence of these minerals determines the chemical composition of the carbonate rooks.

Jan 1, 1983

By Franklin H. Sharp

During the last few years the New Lead Belt of South- eastern Missouri has become the main source of lead in the United States. It also produces significant amounts of zinc, copper, and silver. The mines are located on a narrow, mineralized trend extending southward from Viburnum, Missouri for about thirty-five miles. The area is part of the Ozark uplift and consists of steep-sided, heavily wooded hills with narrow valleys. Surface streams are very erratic, normally having low flows but becoming rushing torrents during the violent thunderstorms that occasionally occur. Because of the pristine nature of the country and the newness of the mining developments, the environmental impact of all phases has been closely watched.

Jan 1, 1973

By J. Lizak

Calcium carbonate is one of the highest volume industrial mineral products in North America. It is used in filler and extender applications, roofing products, floor tile, glass manufacture, etc. Calcium carbonate has over a dozen major filler and extender applications plus a host of minor uses. North American consumption of calcium carbonate fillers and extenders in 1991 is estimated at over 5,000,000 tons valued in excess of $400,000,000. There were five major suppliers of calcium carbonate fillers in the Middle Atlantic region in 1988 :?Bestone, Genstar, National Gypsum, Thomasville Stone and Lime, and White Pigment. With the exception of Genstar's Maryland operation, all of these operations are within a few miles of York, Pennsylvania. The Millington Group (TMG) purchased the assets of Bestone Corporation in February of 1989. TMG then seized the opportunity to strengthen its business position by acquiring National Gypsum's and White Pigment's Pennsylvania filler businesses in December, 1989 and July, 1990, respectively. By July of 1990 TMG's filler business acquisitions included six quarries and one underground mine, totaling over 1,200 acres and three processing facilities. The assets were restructured into two new companies - Delta Carbonate, Inc. and Penroc, Inc. (hereafter collectively referred to as Delta). Delta identified the assets of the three predecessor companies as undervalued from the outset. The initial phase of Delta's turnaround strategy was to reassess the combined mineral. mining, processing, transportation and marketing assets. The second phase was to effectively integrate these resources in order to exploit their inherent synergy.

Jan 1, 1992

By W. C. Painter

In 30 years of experience in Western Mines as Master Mechanic, Chief Electrician and Field Service Representative of Joy Manufacturing Company, I have seen a steady rise in the acceptance of A-C powered equipment for underground use in coal mines. This is also true for potash, gypsum and trona mines where coal mine type equipment and methods are used. This paper covers a large section of actual western mining practice with no theoretical calculations or predictions.

Jan 1, 1959

By B. J. Sauer

Misapplication of AC induction motors for mine crusher and mill applications has long been a frustration for both the driven equipment supplier and the mine operator. Proper selection of AC induction motors is critical to providing efficient production. This paper focuses on the selection of AC induction motors for gyratory crusher, cone crusher, and grinding mill applications. The criteria for motor selection includes: proper enclosure, driven equipment torque requirements, bearing life, temperature rise, starting requirements, ambient temperature, altitude and accessory requirements.

Jan 1, 1999