Search Documents

By Carl G. Hogberg

To the casual observer there is probably no simpler appearing operation in the mineral industry than a limestone quarry. It might seem that the entire operation - from the drilling, blasting, and loading of the stone, its transport to a mill for crushing, washing and sizing, to loading into boats, railroad cars, or trucks for delivery to customers - can be comprehended at a glance. But no first impression could be more misleading. It is one of the purposes of this presentation to sketch the broad outlines of the extensive limestone industry in the United States which, measured in terms of volume of production since the end of World War II, has grown almost 300 per cent to a national level in 1957 of 384 million net tons.1 Another objective will be to discuss in more detail this industry in the State of Michigan. For this latter purpose, the Michigan Limestone Division plants at Calcite and at Cedarville will be used as examples. These descriptions will, we believe, show that the limestone business has complexities to match its size.

Jan 1, 1962

By Peter G. Chamberlain

Novel and innovative mining methods are attracting the attention of mining engineers at an unprecedented level. Historically, the US mining industry has responded rather conservatively to new technology. The financial difficulties affecting the domestic mining industry in the early 1980s changed attitudes toward new technology. The market contraction during that period, coupled with an expanding world mine capacity, created a serious oversupply of many raw mineral products. Many mining companies found that retaining a share of world markets while making a profit required drastic cost-cutting measures.

Jan 1, 2008

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By James M. King

Analytical models for transient groundwater phenomena, such as those of Theis, Cooper, and Jacob, are important but often limited tools for aquifer evaluation and drawdown prediction. Most were developed using simplifying assumptions which compromise their treatment of complex boundaries and most also contain functions that are mathematically complex and difficult to solve explicitly. Examples of such functions are the Bessel functions, the exponential integral, and similar well functions for leaky confined and water table aquifers. This paper describes the joint use of simple numerical techniques and numerical approximations of these functions to extend many analytical models beyond their conventional applications. The enhanced analytical methods represent many hydrologic problems more easily and realistically, permit a wider range of application, and often provide insight into the response of pumped groundwater systems without the need to resort to more complex numerical flow models. Use of the enhanced analytical methods usually requires the use of microcomputers due to the large number of computations. Examples presented here are the development and extension of type curves and the determination of drawdown distributions.

Jan 1, 1984

By Roberto Carranza

The planning of experiments and the importance of statistical interpretation of the results have been recognized for years by scientists and engineers. The Factorial Design of experiments is among the various methods used for this purpose and is being widely applied in all branches of research and production. The basic principles of this tool have been described in detail (1, 2, 3, 4) and several examples of its application in various fields have been published (5). In recent years the mineral industry has also used Factorial Design to improve the efficiency of research, testwork and plant operation (6, 7, 8, 9). This method permits for a qualitative determination of the influence of the variables studied in a process and also a qualitative measure of the interaction of the variables. By graphic means or derivative methods, one may also establish the optimum conditions of the process (ibid 7, 8, 9). It is desirable, however, to develop mathematical methods to evaluate quantitatively these effects and restrict the optimization to the practical limitations of the variables. It is also convenient to adopt a notation system to generalize the Factorial Design.

Jan 1, 1971

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997

By C. L. Molina

The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), Geological Survey of Wyoming, and U.S. Bureau of Mines (USBM), will produce an estimate of the amount of available coal in an area about 55 Ian (35 miles) south of Gillette, Wyo., where the Wyodak coal bed is 8-27 m (25-90 ft) thick. Available coal is coal that actually is accessible for development under current regulatory, land-use, and technologic conditions. Local coal-development considerations include roads, ranches, railroads, pipelines, power lines, wildlife and archaeological sites, alluvial valley floors, cemeteries, and the Hilight oil and gas field and gas plant. Some of these considerations would be mitigated so that surface mining may proceed; others presently preclude mining in their vicinity.

Jan 1, 1995

By Mark E. Emerson

Foreign and domestic companies find the mineral potential of this country's stern public lands, its capital markets, political stability, and "open-door" policy attractive for hard mineral exploration. Traditionally, exploration in the US has been geographically based and responsibility oriented at the district level. The 1970s brought a decentralized approach to exploration as major non-metal companies began to diversify into hard minerals. The emphasis was on capital intensive metal and energy projects involving bulk-tonnages. The recent economic downturn in metals has caused many of the new participants to withdraw from the mineral scene. The surviving companies have shifted their emphasis toward medium scale precious metal projects having high operating margins and rapid return on equity. Exploration expenditures in the United States are now principally focused on gold and silver to the exclusion of practically all other commodities. In the search for precious metals companies have scaled back their exploration efforts and have began to apply new approaches to target selection. The search is being assisted by rapidly evolving conceptual models. The change in orientation has led to numerous new discoveries. The finds are essentially "rediscoveries" that c,-re previously uneconomic. The majority are low-grade surface deposits that have involved low discovery costs and short lead times for development by low-cost mining and beneficiation methods. The emphasis on gold to the exclusion of all other commodities raises questions regarding the direction of exploration in the US for the rest of the 80s.

Jan 1, 1984

By R. W. Sims

"He?s an SOB, but he's my SOB." Many of us have heard this line in reference to attorneys, and can appreciate the humor. However, the thought reflects a deeper attitude that lawyers should be used for attack purposes in the legal system or the regulatory process. Often, more permitting progress can be made with tact and flexibility than with inflexible, overly aggressive strategies. Usually, administrative hearings or other litigation work to the disadvantage of the applicant. Thus, I have concerns about approaching any permitting system with a hard-line attitude. On the other hand, the project team must always be prepared to defend permit applications and present a legally adequate case at public meetings, administrative hearings, or judicial proceedings. This paper discusses a number of strategies intended to increase the probabilities for successful permitting, whether opposition is informal or highly organized.

Jan 1, 1990

By Hassan El-Shall

The results of laboratory and pilot plant testing of a newly developed process to dewater waste slurries from different industries are presented. Data indicate that an increase in solid contents from 6% to over 30% can be obtained in few minutes retention time in comparison to several years as required by currently used technologies. The economical as well as the environmental impacts of such process are discussed.

Jan 1, 1992

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972

By D. L. Lampshire

Biological leaching using native heterotrophic bacteria was studied by the U.S. Bureau of Mines as a means of extracting manganese from a domestic low-grade wad ore. Column heap leaching simulation techniques were employed using molasses as the nutrient source for the bacteria. These column studies were designed to investigate the effects of molasses medium flow rate, concentration, and replacement interval on the extent and rate of manganese extraction. .Results showed that flow rates between 0.41 and 8.1 L/min/m2 had little impact on manganese extraction. The total amount of molasses used did have a direct effect on the extent and rate of manganese extraction. Manganese extractions over 90-pct were obtained in 12 weeks of bioleaching with 2-week medium replacement cycles.

Jan 1, 1993

By E. K. Albert

In 1977, Congress enacted Title IV of the Surface Mining Control and Reclamation Act (SMCRA), providing for an "abandoned ml.ne reclamation fund". This fund, taken from a fee collected from operating coal mines, provides capital for the reclamation process. However, given the number and extent of abandoned mine sites in some states, the question of project selection is important. This paper describes a project in progress to create a Management Information System application for project ranking under multiple objectives. The benefit of this project for the need of new environmental control technologies will be discussed.

Jan 1, 1990

By David Wilson, T. V. Rao

INTRODUCTION The Alchem trona mine, owned and operated by Allied Chemical Corp., is located approximately 32 km (20 miles) west of the town of Green River, and 8 km (5 miles) north of Interstate 80 in southwest Wyoming. Trona, a naturally occuring sodium sesquicarbonate (NaCO3 • NaHCO3 • 2H2O), is used for the production of sodium carbonate (Na2CO3), commonly known as soda ash. Present annual US consumption of soda ash is approximately 9.07 Mt (10 million st), out of which approximately 7.3 Mt (8 million st) is produced from the Wyoming trona mines. About 44% of soda ash is consumed by the glass industry; 3 % by exports; and the remaining portion by paper, chemical, soap, textile, and nonferrous industries. Allied Chemical operates an underground mine at an average depth of about 488 m (1600 ft). There are three other trona mines in the area operated by FMC Corp., Stauffer Chemical Corp., and Texasgulf Inc. (see Fig. 1). Allied Chemical became interested in southwest Wyoming trona deposits in the early 1940s. Explora¬tion work was begun in 1959 with the acquisition of federal leases. Exploitation of the reserves began in 1968. Two shafts, one 6.1 m (20 ft) and another 3.7 m (12 ft), were completed prior to 1968. The 6.1-m (20-ft) diam service shaft is divided in half by a cur¬tain wall, with one half used for men and material and the other for ventilation as a return air shaft. During the period from 1968 to 1974, the 3.7-m (12-ft) shaft was used as production shaft with two 7.3-t (8-st) skips. Due to the increased demand for soda ash, plant and mine expansions were completed during 1974. Under this expansion, the material handling system capacity was increased by constructing a new 2721-t (3000-st) capacity ore bin, sinking a 6.1-m (20-ft) diam produc¬tion shaft, and installing a friction hoist with two 22.7-t (25-st) skips. The Alchem mine manpower is 484 employees and about 2.3 Mt (2.5 million st) of trona was produced during 1976. Three different mining systems are used at the Alchem mine: conventional, continuous, and longwall. Allied Chemical introduced its first longwall unit in 1973, which was also the first longwall system introduced in the Wyoming trona district. At present, four conventional, seven continuous, and two longwall units are in operation. This equipment is operated in ten production areas. GEOLOGY The bedded trona and trona-halite in the Green River basin of southwestern Wyoming is a major re¬source for the nation. There are 25 beds that exceed 0.9 m (3 ft) in thickness and underlie areas of about 2590 km2 (1000 sq miles). There are other minor beds that range in thickness from 0.3 to 1.2 m (1 to 4 ft). Allied Chemical's Alchem mine is located in bed 17. The trona bed numbering system starts at the lowest elevation and increases upwards. The trona beds are in the Wilkens Peak member of the Green River formation. The Green River formation was deposited in a lake that began in early Eocene as a large body of fresh water, shrank in size and became saline, and then became fresh water again. The sedi¬ment during the saline phase of the lake, which includes the trona beds, is called the Wilkens Peak member. The underlying freshwater lake deposit is called the Tipton member and includes a 25.9-m (85-ft) sand unit which is a high pressure, low permeability aquifer. The over¬lying sediment is called the Laney shale. The Green River formation is underlaid by the Wasatch formation and overlaid by the Bridger formation (see Fig. 2). The structure of the beds in the area of the Allied Chemical mine is mostly postdepositional asymmetrical folds of small amplitude. These folds range in size of 3 to 6.1 m (10 to 20 ft) to as much as 45.7 m (150 ft). The trend of the folds is northwesterly with the north¬east flank of the anticlines having a steep dip and the southwest having gentle dips. Trona bed 17 varies in thickness from 2.4 to 3.4 m (8 to 11 ft) over the 93.2 km2 (36 sq miles) holdings of Allied Chemical and is flat lying except for the rela¬tively minor folding and a negligible regional dip of about 0.017 rad (1°). Trona occurs naturally in several physical forms in the Green River basin, being both massive and crystal¬line. The trona ore in the Alchem mine is a fine-grained massive ore with a compressive strength of approxi-

Jan 1, 1982

By R. F. Pearce

The paper in based on laboratory and pilot plant investigations which led to the development of a series of processes for production of high purity metals from nickel-copper-cobalt mattes of a wide range of composition. The selection of ammonia pressure leaching or acid pressure leaching for various mattes is discussed. This is followed by discussion of various methods for leach solution purification and metal separation. The metals of high purity are produced by reduction with hydrogen from purified solutions. Examples are given of complete flowsheets for a number of mattes. Drawing upon those examples, general principles for the selection of the most suitable treatment process for particular material are outlined. Under certain circumstances, those processes may replace part of the pyrometallurgical treatment and all of the electrolytic refining steps which are customary in the treatment of nickel-copper-cobalt mattes.

Jan 1, 1959

By F. J. Susko

The Bureau of Mines investigated rapid bubble-pulp separation to improve flotation kinetics. A shallow-depth froth separator was employed to quickly recover the mineral-laden bubbles from a mixture of ore, water, and air bubbles. The shallow depth minimized the rising distance required to recover even the smallest size bubbles (100 ~m). Therefore, the slurry remained in the unit only long enough to recover the bubbles before the pulp exited through the conical bottom. Joining this unit with a rapid bubble-particle attachment unit, a rapid flotation system was formed that floated silica from phosphate in one-fifth of the retention time for conventional mechanical cells. The hydrodynamics of the rapid flotation system along with fundamental parameters for scale-up are presented in this paper.

Jan 1, 1992

By William F. Abercrombie

The role of the laboratory is described in relation to the prospecting and exploration of kaolin clays. Test methods used to evaluate crude ore samples of kaolin clay for commercial consideration are reviewed. A background of the kaolin mineral and known means of prospecting this mineral are presented. Common analytical methods are discussed with special emphasis on those in use today.

Jan 1, 1982

By Roger Bell

Most modern mines can profit from improvements in information handling. Recording systems in many cases were designed to satisfy certain necessary legal requirements, but not specifically to provide management information. As a consequence, the top managements of these properties work with cost data and production information that is dated, lacking in detail and clouded with supposition. It is the intent of this paper to describe an information system for a mine-plant complex in terms of the type of data, application areas and the existing equipment technology that may be applied to improve this situation. The economics of information processing and data handling will not be discussed in detail. This paper is based on the premise that information is something of value and that information processing like a manufacturing operation works for and is subject to management control. Information, the product, must be of quality, and the cost must be favorable in terms of its use.

Jan 1, 1965

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to develop a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 ppm WO3). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten vas recovered as a marketable iron-tungsten concentrate containing 44 percent tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process investigation unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By Lu Yang

In the last two decades, acid iron ore pellets have established their predominant position as the iron-bearing burden material for blast furnace ironmaking in North America. It is a general practice that pelletization plants are asked to produce pellets of certain chemical composition and in a narrow range of sizes. A minimum amount of fines created during handling and transportation is desirable. Such a requirement is often expressed indirectly by the minimum compression load causing a pellet to break. The behavior of pellets inside a blast furnace, of course, is very important for a smooth and efficient operation. Before its melting in the lower part of a blast furnace during this period of several hours the behavior of pellets depends on their properties after induration as well as conditions inside each furnace. Among properties of indurated pellets, the ability to maintain their physical integrity in the burden and to be reducible are most important. To maintain the integrity of pellets (i.e., minimal low temperature breakdown, swelling and softening) so that there will be adequate overall permeability for certain wind rate and local permeability for gas/solid contact for reduction. A higher reducibility will moderate the adverse effects of swelling and softening and contribute to a smooth operation and efficient use of heat and reductants in a blast furnace. An article devoted to the relationships between the quality of iron ore pellets and blast furnace practice has been published elsewhere(1); therefore, no further discussion is needed here. The mechanism of strengthening of iron ore pellets during firing has been the subject of investigation of many authors(2). There is no doubt that the bridging of the growing hematite grains, particularly starting with magnetite concentrates, is very significant in the production of strong pellets. Recently, there are many reports from blast furnace operators that they have noticed the adverse effect of LTB in their plants. It is obvious that the strength derived from bridged hematite grains may disappear when hematite is converted to magnetite with thorough breakdown of grain structures. It is suggested that some other strengthening mechanism may be required in order to improve the LTB index of acid pellets. The influence of porosity on both compression strength and reducibility follows regular patterns. It has been suggested(1) that the amount of liquid slag in pellets during firing determines to a large extent the porosity, hence, indirectly, strength and reducibility.

Jan 1, 1983