Search Documents

By Lawson. Heather

"The purpose of this study is to explore how the geochemical and petrographic components of coal may impact its physical properties, as well as how these components correlate with a history of reportable dynamic failure in coal mines. Dynamic failure events, also termed bumps, bounces, or bursts, are the explosive failures of rock in a mining environment. These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of MSHA reportable cases. A database of variables was compiled using publicly available datasets, which included compositional geographic, strength, and Hardgrove Grindability Index (HGI) data (ACARP, 1998). Results indicate that bumping coals are less mature, lower in carbon, higher in oxygen, softer, and less well cleated than coals that do not bump. High liptinite content was found to correlate with higher average UCS values. However, no clear, direct correlation between UCS and dynamic failure status was observed. The findings of this study establish that differences exist between coals that have experienced reportable dynamic failure accidents versus those that have not. These differences are inherent to the coal itself, independent of mining-induced risk factors. Results further illuminate how compositional attributes of coal influence physical properties and begin to clarify potential links between geochemistry and dynamic failure status. Only through the better understanding of risk can more effective mitigating strategies be enacted.INTRODUCTIONDynamic failure events, also termed bumps, bounces, or bursts, are the sudden failures of rock in a mining or quarrying environment. Failure occurs when the rock’s critical bearing capacity has been exceeded and the rock fails energetically through the outward expulsion of rubblized material (Peng, 2008). These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of reported cases through the Mine Safety and Health Administration (MSHA). Much research has been devoted to the prevention of these events. The effects of overburden depth and stiffness, mine design, mining practices, and in situ stresses are well documented (Agapito and Goodrich, 2000; Brauner, 1994; Campoli and Kertis, 1987; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Lawson et al., 2016b; Mark, 2016; Newman, 2002; Peng, 2008; Whyatt, 2008). Despite these significant advancements in coal mine ground control, however, events continue to occur. Proactive risk mitigation remains an important research area. This is particularly true in underground coal settings, where the rockmass is layered, lithologically diverse, and does not exhibit consistent material properties across deposits.Many conditions have been associated with the occurrence of dynamic failure phenomena, including:"

Jan 1, 2019

Ventilation 'is currently used in mines to sustain human life, prevent explosions, and provide a more healthful work place. Future automated-mining systems could use ventilation techniques quite. different from today's practices. The Bureau of Mines is anticipating various methodologies for ventilating the automated mining systems which are now beginning to emerge in the mining industry. This paper examines the special ventilation requirements for automated mining systems. Topics include requirements for automated systems, current studies with blowup ventilation tubing, and ventilation of two types of highwall -ripper type mining machines.

Jan 1, 1990

By Peter Ralph

All copper ore haulage at Isamine was transferred to the new 19 level haulage network by mid 1975. Previous experience together with design studies had indicated that a three train operation would be required to haul the scheduled ore production. The ore train with a gross weight of 600 tonne is made up of 15 bottom dumping trucks hauled by twin electric locomotives (Figure 1). Present train speeds reach 40 km/hr and, in the future, this speed could be increased to 55 km/hr. The planned operation on the restricted track network and the relatively high train speed meant that the train driver operated block light system would be inadequate on the grounds of haulage safety and meeting production targets. Some form of Centralised Train Control (CTC) system emerged as a necessity, and as an initial step, tenders were called for a relay control type CTC system. The high cost of these systems and the anticipated high maintenance costs and inflexibility of the offered systems led to the rejection of the tenders. It was decided to develop a CTC system locally and to use a digital computer to perform the basic track [ ] equipment interlocking tasks and monitor haulage operation.

Jan 1, 1979

By Gregg J. Hodges

The Stillwater Mining Company, a partnership of The Pittsburg & Midway Coal Mining Co. and Manville Corporation, began commercial production of flotation concentrates from the western hemispheres' only primary platinum palladium deposit at Nye, Montana in March 1937. In the fall of 1987 an integrated pilot plant testing campaign of electric furnace smelling and oxygen? blown converting confirmed the feasibility of further upgrading to semi? refined matte or 'white metal". In the summer of 1990 the production smelter was brought on-line at Columbus, Montana. This paper describes the technology transfer from the pilot to the production smelter. Emphasis is placed on flowsheet development and the scale factors between the test and production furnaces and gas cleaning plants. The metallurgical results of the pilot plant and of the early months of production of the commercial works are also compared.

Jan 1, 1991

By Donald A. Dahlstrom, Wai-Ping Kam

The mineral industry and individual processing plants are large consumers of energy. While energy conservation has received some attention in the present Federal Administration National Energy Strategy proposal it is obvious that the mineral industry should also continue to emphasize energy consumption reduction for important economic savings alone. As indicated by other studies, comminution is the largest single consumer of energy in the mineral processing plant (1.3% of total electrical energy consumption in the U.S.A.).1 Fine grinding is the largest portion of this amazing statistic. While substantial energy savings have been demonstrated by new machine developments and improved control methods, undoubtedly there are additional areas in comminution where substantial progress can be made. Some time ago, the U.S. Department of Energy published a report on "Comminution and Energy Consumption" by a committee composed of experts in the field of comminution from industry and academia. They identified the following potential for energy savings by specific areas? Classification device design 9-13% Comminution device design 3-16% Control 9% Grinding additive 3-6% Materials 3% It is apparent that the classification device had the first or second highest savings potential. Obviously, serious research consideration must be given to this technology area. A series of three papers have previously been written on the subject of two stage classification research work for ball mill operation by the authors. Accordingly, a brief review will be made. Previous Research Results on Two Stage Classification The hydrocyclone was selected as the type of classification equipment for this study as it represents by far the majority of the devices used in ball milling. While four different hydrocyclone circuits have been proposed by others,3 only two were considered in this work as illustrated in Figure 1. Flowsheet A is truly counter-current in nature in that the product from the ball milling circuit is taken from the first stage overflow

Jan 1, 1992

By J. L. Boyd

The mining and processing of basic metals relies on water as a medium for transport. Metallurgical ores are ground, concentrated, leached and refined in an aqueous medium. Water is used for temperature control during processing and in air pollution abatement during smelting. All of these process steps result in liquid wastes. Many of the aqueous wastes from ore processing areas become the raw product for a second stage and water recycling may begin. The point at which water recycling or reuse has been initiated in the past, rather than water discharge, was where water conservation was manditory due to a shortage, where process conditions would allow or benefit from reuse, and where economic considerations demanded reuse. The Fontana, California plant of Kaiser Steel Corporation is an example of an integrated steel plant that was forced to practice water conservation and reuse due to its location in an arid environment.1 Only a small amount of water required to maintain the water reuse system in balance with respect to dissolved solids and product quality is discharged. The Butte, Montana copper ore processing plant of The Anaconda Company obtains 66% of the water required for production by recycling, after clarification and chemical treatment, 30 MGD of wastewater from its tailings ponds. This operation is estimated to save the company about $1200/day over a once through water system.2 Here plant location and economics favored water reuse.

Jan 1, 1975

By M. Noppé

"Dilution in underground coal operations can be underestimated by up to five times during Feasibility Studies, with disastrous economic consequences. Every 1% of stone waste introduced can reduce an in situ specific energy of 11,000 BTU/lb (25 MJ/kg) by some 110 BTU/lb (0.25 MJ/kg) and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some AU$1 million per year.This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation. The dilution trends before and after introducing the recommended controls in a continuous miner/longwall mine are presented over an eight year period. The additional information from such a dilution monitoring program can also be used to control mining horizons and plan longwall extraction heights across the face proactively, on a short-term scale with resulting improvements in productivity. INTRODUCTION Grade control, as practiced on any mine, is concerned with predicting routine quality and tonnage values for short- to medium-term mining operations, and the reconciliation of these predictions against “actual” results. For a longwall mine supplying steam coal, such routine parameters may include the proximate analyses, specific energy (SE), abrasiveness and sulphur, as well as float and sink analyses if the coal is beneficiated. In addition, grade control is concerned with identifying the mineable horizon (or horizons) in a selective-mining operation, together with monitoring how well these horizons have been extracted or adhered to. Close-spaced surface drilling can be costly for any mining venture, particularly for longwall mines operating in the deeper seams. For this reason, much of the data for short-term grade control requirements are acquired during actual bord-and-pillar development. The underground data are derived from so-called “channel” samples. These samples are cut or chipped from the coal seam, perpendicular to the mining horizon, with dimensions suitable for obtaining sufficient “representative” sample for analyses. For a 2m thick mining horizon, a channel sample 300 mm wide and 50 mm deep over the thickness of the horizon would provide some 4.5 kg of sample, sufficient for most of the necessary tests. To allow the information to be computer recorded, additional information such as seam thickness, sample co-ordinates, and the elevation of the seam (or horizon) roof or floor, may be required."

Jan 1, 2015

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By Thomas E. Finch

Coal produced from surface mines in the Western United States is becoming a more important part of this nation's economy as other types of fuels become scarce. This paper reports the investigation of alternative methods of handling the parting between two coal seams. The results of this investigation are presented as the engineering-economic aspects of alternative parting handling methods involving stowing or back filling techniques. The coal and parting characteristics were selected as being representative of those under consideration or actively mined in the West. The basic philosophy of evaluation is to establish a mine-within-a-mine where equipment selected for minimal capital investment can remove the parting and second seam nearly independent of the ongoing, present production. With proper consideration of design, this parting-coal removal is evaluated as a second operation within the first and has its own profitability measure. The Fort Union Area of Montana, Wyoming, and the Dakotas contains large reserves of low sulfur sub-bituminous coal. In many locations, several coal seams are close to the surface and are separated by relatively thin layers of parting. The removal of overburden and the mining of the upper seam is accomplished effectively with conventional mining methods and equipment. Mining a second seam of coal and handling the parting in accord with economic and environmental controls presents a number of problems. Typically, mining companies have adapted the conventional strip mining techniques used in the East. However, the extreme thickness of the western coal seams offers alternative mining method possibilities for parting and second seam removal.

Jan 1, 1976

By C. Hosten

This paper presents the results from an extensive research program on the vacuum filtration of iron ore slurries. Experiments were conducted with the addition of several types of flocculants and surfactants. The filtration response of the slurries was studied in terms of the cake formation rate and the residual cake moisture. An analysis of the results is presented in ascertaining the role of flocculants and surfactants during filtration

Jan 1, 1983

By K. H. Nimerick

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 1, 1977

By J. A. Bartnik

Flocculation, the process of coagulation or coalescence of finely divided particles, is commonly used in separating fine solids from fluids. Forces disposing of the particles to flocculate include: ionic forces of attraction, secondary entropic forces, and magnetism. Magnetic flocculation is due to a physical magnetizing process which affects suspended ferromagnetic particles. Such particles, after exposure to magnetic fields strong enough to cause reorientation of the particles and alignment of the induced magnetic poles, tend strongly to retain this induced magnetism, as the magnetic retentivity of ferromagnetic particles is a linear function of its specific surface.1 Thus, because they become small magnets with high residual magnetism, the particles become and remain attracted to one another, forming large agglomerates. Fine magnetic particles close to domain size can exhibit energies of the magnetization of the order of 105 ergs/cm3,2 which is many times greater than the energy affected by chemical flocculents. Therefore magnetic flocculation can be used to agglomerate particles having surfaces ionized with like charges and only a minute quantity of ferromagnetic material will be necessary to develop sufficient force to overcome the repulsive ionic forces and hold together relatively large masses of fine solid agglomerates suspended in fluids. Since flocculation occurs after the fine suspension passes through a magnetic field generated by magnets surrounding a pipe section, the simplicity of the process and economic advantage makes magnetic flocculation very attractive.

Jan 1, 1971

By PDF

The adsorption of ethoxylated sulfonates and nonionics of the same ethoxylation number?on a low-ash coal has been studied. The surfactant adsorption has been investigated as a function of concentration, pH, temperature and ionic strength for three homologues. Zeta potential of coal particles and surface tension of supernatants has been concurrently determined to eludicate the orientation of sudactant molecules on the coal surface as well as the mechanism of adsorption process. The adsorption data are utilized to calculate thermodynamic parameters such as the free energy of adsorption and isoteric heats of adsorption.

Jan 1, 1988

By L. Lichty, R Bhappu, R. Rowan, G. Ramadorai

Treatment of refractory gold ores containing arsenic have always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries, production of hazardous fumes, effluents and residues. Because of'these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processee for refractory gold ores and concentrates have been explored and a few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180% to 200%) and pressures (400 psi) is accompanied by high capital and operating costs. An alternate route to roasting for treating pyrite and arsenopyrite ores and concentrates ia the "lime-oxygen hydromet" process carried out at a moderate temperature (100%) and pressure (100 psi). A simplified process for treating such arsenic containing ores and concentrates utilizing low temperature and pressure oxidation is presented. This low cost treatment with compressed air and lime renders arsenic as an inert component in the residue, meeting all the requirements of the EPA Toxicity Test. The precious metal values are then extracted from the autoclaved residue by standard cyanidation. This paper discusses this new development.

Jan 1, 1990

By William I. Weisman

The annual consumption of fluorspar in the United States, in the last 10 years has doubled. In 1971, when 1,344,742 tons were consumed, almost 45 percent of this amount was used in the production of steel and nearly 50 percent was consumed in the manufacture of hydrofluoric acid. Of the hydrofluoric acid produced, about one-third was used in the manufacture of aluminum electrolytes for production of primary aluminum metal and the balance was consumed in the manufacture of a variety of fluorocarbons and other chemicals. A small amount of fluorspar, constituting less than five percent of total consumption, was used in the foundry industry, and in the manufacture of glass, enamel, cement and other products. It is apparent that a continuing supply of fluorspar will be required to meet the demands for these vital metals and chemicals in our expanding industrial society. Domestic fluorspar production meets only approximately 20 percent of our needs. Hence, it is essential that the United States maintain a healthy domestic fluorspar industry in order to have adequate domestic reserves available at times of emergency and to protect this country from becoming solely dependent on foreign sources for this strategic commodity.

Jan 1, 1973

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By T. J. Fenner

Surface and underground mining operations are often hindered by unknown tunnels and stopes and the precise locations of adjacent workings. Mine safety and planning are adversely affected especially in previously undermined areas where historical records are incomplete or non-existent. The results of several Ground Penetrating Radar (GPR) studies for the detection of known mine tunnels in underground coal; salt, and gold mines are presented. A case study to locate unknown, abandoned mine workings at a surface gold mine successfully located all workings to a depth of 11 meters.

Jan 1, 1992

By Charles H. Jacoby

The economic importance of salt domes has been recognized throughout the world primarily because of oil and gas accumulations on their flanks and, to a lesser degree, for the value of their salt and potash. Recently they have become of value as hosts for cavities used to store hydrocarbons. In the near future we believe that their main value will be as a source of geothermal energy. Although tremendous effort has been expended on the understanding of the geology and physical characteristics of the strata intruded by salt domes, relatively little energy has been exerted in the comprehension of the salt dome itself. Salt domes have long been recognized as a geological heat anomaly. With respect to other sedimentary rocks, salt is a good conductor of heat. Expressing values in 10-3 cgs units, sedimentary rocks vary from 1.0 to 8.0; metamorphic rocks from 5.2 to 8.4 and igneous rocks from 3.1 to 9.8. Rock salt in its pure form has a thermal conductivity of 17. (Gussow, 1970). Thus a salt dome (Fig. Ml) can be expected to act as a conduit bringing heat vertically from deep within the Earth's crust. This was, in part, substantiated when in 1958 a horizontal core hole was drilled from within the Avery Island Mine at the 500 foot level. The horizontal hole was started where the ambient temperature of the salt was 74° F. and drilled toward the center of the dome. At the end of this 2,000 foot hole the temperature was 90° F. thus depicting a horizontal temperature gradient of 7° F./1,000 feet. Because this core hole penetrated a shear zone connate water that appeared as a "cold spot" on the temperature gradient, the foregoing data can only be regarded as indicative.

Jan 1, 1974

The following errors were inadvertently included in "How millisecond delay periods may enhance or reduce blast vibration effects" by R.M. Wheeler in the September issue of Mining Engineering.

Jan 1, 1987