Search Documents

By Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducrng bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the porosities of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also extended a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore modes. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of the first of June 1984, a total of 29.4 million long tons of sulphur had been produced west of the Pecos -aver. Duval produced more than 88 percent of that total.

Jan 1, 1984

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By F. G. Miller

In mid-1972 we determined that a fresh approach to coal mining research was needed for the industry as well as for Bethlehem. The reasons to us were obvious: Productivity was in the throes of a steady decline, and labor and maintenance costs were spiraling upward. Yet, despite this predicament, nowhere in the U.S. at that time was there a comprehensive and coordinated research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. After studying our own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, we presented a comprehensive research package to our management at the end of 1972. The ideas and experience of many operating and management personnel in our Corporation contributed to the formulation of the final plan as approved.

Jan 1, 1976

By R. J. Kolada

The ventilation systems of coal storage silos are normally capable of rapidly dispersing any accumulations of methane in the atmosphere above the coal pile surface. However, the results of an investigation which is presented in this report show that hazardous concentrations of methane can accumulate within the coal pile. Methane trapped within the coal pile is released into the atmosphere of the loading gallery when coal is discharged from a silo. If the methane released is of a flammable concentration it is necessary to ventilate the gallery to reduce the risk of an ignition. This report proposes a simple test, which, after further investigations may prove to be an effective method to calculate gallery ventilation requirements.

Jan 1, 1985

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By Rudolf E. Greuer

Modeling a mine ventilation system is a formidable mathematical problem requiring the solution of twice as many equations as there are airways with half of these being quadratic equations. The addition of a mine fire to the problem adds many more complexities. The U.S. Bureau of Mines and Michigan Technological University attacked this problem in stages. During the 1970's and 80's, a series of computer simulation programs were developed which offered progressively increasing levels of modeling capability and accuracy. The current version of this software, MFIRE 2.0, was released in 1993. This programs provides for full dynamic state mass flow-based modeling of a mine ventilation system, and includes natural ventilation, mechanical ventilation, air reversals and recirculation, methane and fire contaminant spread, and moisture condensation and evaporation in the mass flow and heat exchange calculations. This program is a useful tool for routine ventilation planning and can significantly improve mine safety by enabling detailed quantitative analysis for mine emergency preplanning. This paper reviews the evolution of the MFIRE program from its infancy as a simple digital network simulator replacing analog computers to the present version.

Jan 1, 1994

By J. H. Dietz

The electric assist option for diesel-electric trucks can improve truck productivity while maintaining the inherent flexibility of a truck and shovel operation. In addition, the resulting cost reductions offer a rapid investment payback for many mine situations. A review of the present technology and performance experiences verify the projected benefits in productivity and operating cost. New technologies can further improve the productivity/cost scenario.

Jan 1, 1984

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By J. J. Harrington

Manufacture and mixing of flotation reagents at the mill site provides an economic and convenient method of maintaining a continuous and fresh supply of reagents for concentrator operations. Kennecott Copper Corporation has designed and built a Reagent Mixing Facility which incorporates new ideas in construction and fail-safe operation at its Nevada Mines Division concentrator. Highly sophisticated automation and instrumentation techniques are combined with safety procedures and equipment that meet and exceed all Federal and State safety requirements. Installation of the facility has minimized hazardous working conditions for the operator, isolated reagent preparation from production personnel and equipment, and reduced the time required for reagent preparation from three shifts to one shift per day.

Jan 1, 1976

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By W. L. Dalke

The Minntac complex is a facility for production of iron ore pellets located on the Mesabi Range at mountain iron, Minnesota. It consists basically of a mine, crushing plant, concentrator, and a pelletizer producing twelve and one-half million tons of pellets annually. This paper deals with some of the aspects of the grinding circuits; but prior to that discussion, it might be well to briefly describe the flow of material in the operation. The crude ore, containing from 20% to 25% magnetic iron, is mined by 14-yard electric shovels. .the blasted ore is loaded directly into 50-yard side dump railroad cars and hauled to the crushing plant. Crushing is done in three stages, originally, two 60" primary crushers; four 7-foot standard secondary crushers; and six 7-foot short head tertiary crushers were installed, when the plant was expanded to double its capacity, five secondary and ten tertiary crushers were added. These were duplicates of the original 7-foot standard and short head crushers used in the original construction, there was no expansion of the primary crushers but a one-half-million-ton surge pile of tertiary crusher feed was added.

Jan 1, 1976

By F. Milton Lewis

Several alternatives are available for treating lover grade gold ores averaging 0.04 to 0.10 ounce per ton. These include heap, vat and agitation leaching and may involve conventional zinc precipitation or carbon adsorption-electrowinning systems. Each of these processes have their inherent economic and operating advantages and disadvantages and the selection of the optimum method for a given gold ore is solely based on economic evaluation of the applicable processes. In this paper an effort is made to provide engineering feasibility estimates for the above processes under varying operational conditions such as ore grade and price of gold.

Jan 1, 1974

By David M. Koogler

If you are contemplating starting a small coal mining operation there is a good possi¬bility that you can not afford it. If you, have already started, you may be on the road to bankruptcy. If you are a small but well established operator you may be trading dollars, or even dissipating your capital, equipment and other assets. A bleak outlook? Yes! Meant to be discouraging? No! Just a reminder that, with todays costs of doing business, high interest rates, rapidly increasing costs and decreasing sales prices, a small businessman/miner had best watch closely or he will be mired in something worse than a soft bottom - namely a cash and credit shortage, and in too many instances In recent times, bankruptcy. We will not dwell on what happens once you are that far gone, though I could cite a good example. But, let us look at what should be done to avoid such a catastrophe.

Jan 1, 1981

By J. Moreno, P. Sinton, R. Vogwill

Groundwater models are often used to estimate and optimize dewatering volumes, locations, and rates, as well as water supply production for mines. Projections of future dewatering rates are highly dependent on the conceptual model used as a basis for the numerical model. This paper presents an audit of modeled dewatering rates versus actual data and an examination of the reasons for discrepancies. The setting is a gold mine, in a collapsed volcanic crater breached by the ocean. Mining will occur to about 200m below sea level within a remnant geothermal system. A detailed hydrogeologic investigation was conducted to support dewatering and geothermal depressurization design for future mining operations. These studies included development of a three-dimensional model to simulate heat and density-coupled groundwater flow, using software developed by URS/Dames & Moore. In this paper, the groundwater modeling results prepared 5 years previously by others was audited using operational dewatering data. This model was then extended using the new mine schedule and actual locations for dewatering wells to predict future dewatering requirements. In addition, a comparison between “hot” and “cold” model results was used to assess the need to use a heat-coupled versus a standard groundwater model for dewatering predictions.

Jan 1, 2003

By Ben L. Seegmiller

How to obtain optimum slope angles for future open pit mines using the rock mechanics approach is the subject of this paper. In the past ten years significant developments in open pit rock mechanics have come about. This has been due to the mining industry's need for the steepest, yet safe, pit slope angles attainable. Requirements for economically achieving slope stability and the actual payoff that may be achieved through stability studies have been previously discussed', by stability engineers. While the emphasis has generally been placed on the concept of "stable slopes" in the past, it is suggested that emphasis now be placed on "optimum slopes" or "optimum slope angles". A definition of an optimum slope angle is one which (1) is as steep as possible and practical from orebody and mining constraint standpoints and yet, (2) maintains the accepted standard of safety defined by a safety factor against failure and/or a probability of failure. In other words, the emphasis is placed on achieving practical stability results as defined by safety and economic considerations, as opposed to simply achieving stability. The essential purposes of this paper are to (1) outline the need for optimum slope angles, (2) discuss the procedures for using the rock mechanics approach in slope angle design for a future open pit and (3) specify the end results that may be achieved by using such an approach. While the basic concepts and recommendations outlined in this paper may be equally applicable to soil as well as rock slopes, the emphasis and procedures have been directed at rock slope angle design.

Jan 1, 1976

By S. B. Hildebrand

One of the highest costs associated with insitu leaching of copper is electric power. The ReGeneration Project addressed this cost issue with a research and development project for BHP Copper. The project involved the installation of a reverse pump/turbine for the removal of excessive fluid pressure and the production of useful electric power. The motivation for the project was that a reverse pump/turbine unit could not only remove the excess hydraulic pressure, but when connected to an induction .generator, would produce electric power, which could be easily connected to the local power gird, thus reducing operating costs. The project was successful in removing excess fluid pressure and producing electricity. The unit is operating today, producing useful 2,300 volt power at a rate of approximately 128 kilowatts.

Jan 1, 1998

By Roger N. Miller

Talc mining in Vermont has in recent years undergone a progressive change in mining methods and in mining equipment. Underground mines have been phased out except in special circum- stances, and continuous mining machines (CMM?s) have replaced conventional drill/blast mining systems. Talc mining in Vermont began in the late 1800?s, and has continued without interruption to date. Beneficiation (flotation) has been applied since the early 1930?s, and has provided special products for toiletries and other markets. At the present time, there are two active companies that have evolved from the cumulative absorption of nearly ten smaller operations.

Jan 1, 1984

By B. Zane Egan

The Calsinter process for recovery from fly ash involves sintering the fly ash with calcium sulfate and calcium carbonate at 1200°C, followed by a dilute sulfuric acid leach step. Flue gas desulfurization sludge containing calcium sulfite, calcium sulfate, and unreacted calcium carbonate may be substituted for the calcium sulfate and calcium carbonate. Conversion of aluminum in fly ash by the sintering process to an acid-leachable species was measured as a function of sintering time and temperature in the range of 800°-1200°C The sinter-leach steps were investigated using thermogravimetric analysis, x-ray diffraction, scanning electron microscopy, and elemental analysis. SEM photographs indicated that the glassy spheroids in the original fly ash were converted to a crystalline structure by the sintering reaction.

Jan 1, 1980

By R. H. Roberts

The Environment Weipa is located at 12° south latitude on the west coast of Cape York Peninsula, North Queensland, Australia. The climate is tropical with most of the 1 600 mm. average annual rainfall falling between November and March. During the short winter months (May/ August) the weather is clear and pleasant, with temperatures seldom exceeding 27°C.Throughout the remainder of the year, conditions are frequently oppressive due to consistent high ambient temperatures accompanied by high humidity. The terrain is of low relief, and generally not more than 6 to 10m. above mean sea level adjacent to the coast. The coastline features numerous short estuaries which discharge run-off from the heavy rains collected by creeks and rivers. The whole area is covered by an open forest, the predominant species of which is Eucalyptus tetradonta. These eucalypts have only limited commercial value and are heavily infested with termites. Despite the fact that Weipa is close to the location of the first reported sighting of the Australian coastline by a European (William Janz - 1606), it remains very isolated. There is no developed road or rail connection to centres of population, so that transport of practically all products, personnel and materials to and from Weipa is by sea and air. Cairns (population 49 000) is 580 km. by air and 670 nautical miles by sea; Brisbane, the

Jan 1, 1977