Search Documents

By Kenneth S. Johnson

Large reserves of high-purity Permian gypsum crop out and are at shallow depth in three regions of western Oklahoma, Gypsum beds in the Blaine Formation are 10 to 30 feet thick and are generally 95 to 99 percent pure, whereas the massive Cloud Chief Gypsum is 20 to 100 feet thick and is 92 to 97 percent pure. Reserves are estimated at 48 billion short tons. Eight companies in the State currently mine about 1 million tons of gypsum each year for wall- board, for plaster, as a retarder in portland cement, and as a soil conditioner. Future uses, under more favorable market conditions, may be in the chemical industries, largely because of gypsum's potential as a source of sulfur. Three thick sequences of Permian rock salt underlie most of western Oklahoma at depths of 30 to 3,000 feet. Individual salt beds 5 to 30 feet thick are interbedded with thinner layers of shale and anhydrite. Five large salt plains, fed by natural springs of saturated brine constitute additional resources of salt. Reserves, estimated at 20 trillion short tons, are virtually untapped, and, ironically, about 90 percent of the salt used in Oklahoma is imported. Chemical data on the rock salt are lacking, but evaporated salt produced from brines is generally 97 to 99 percent pure. Current production from three solar-evaporation plants is used mainly for stockfeed, recharging water softeners, and deicing roads. Potential uses are in the chemical industries, where salt or brine is a necessary raw material.

Jan 1, 1973

By W. R. VanSlyke

Scrubbing is gaining increasing recognition as a valuable tool in the treatment of Mesabi Range intermediate iron ores. In general, the earliest washing plants included log-washers in their various flowsheets. While log-washers certainly did impart a degree of scrubbing to the crude ore, such treatment bears little resemblance to the type of scrubbing being practiced today. At the time that these early plants were erected, only the true wash-ores were being processd. ("Wash-ores" are defined as crude ores in which relatively coarse chunks of almost completely liberated iron are found in a matrix of loosely-consolidated fine sand.) To treat ores of this type, sizing at approximately 65 to 100 mesh was sufficient to produce a merchantable concentrate. As crudes were being treated in which there was little "locking" of iron and silica, log-washers tended to disappear and large screens and classifiers took their place in Mesabi range flowsheets. The "screening and classification" type of flowsheet 'had its greatest usage in the 1945-55 period, generally speaking. During this same period, many operators found it necessary to supplement the "wash-ore" type flowsheet with heavy-media treatment.

Jan 1, 1959

By A. J. Basu

Rock mass properties testing for determining strength parameters is an integral part of geomechanics. These tests are performed either in a laboratory environment or in a field (in-situ). The authors share their experience in using numerical modelling in simulating the laboratory test procedures. This approach helps studying the rock breakage and failure mechanism more efficiently and provides a high degree of visualization. Moreover, imperfections and discontinuities can be easily incorporated in these models. This capability of providing arbitrary fractures and discontinuities facilitates in building a large knowledgebase of rock strength and failure mechanisms. This knowledgebase may then be used to generate heuristics for determining rock strengths for rock mass with fractures and discontinuities.

Jan 1, 1997

By W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable dust samples from underground coal mines is the P-7 method, a combination of low temperature radio-frequency ashing (LTA) and infrared analysis (lR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive Infrared (IR), Fourier-transform Infrared (FTIR), and X-Ray Diffraction (XRD) methods are most commonly used for quartz analysis in powders. Several aspects of the experimental procedures such as the analysis sample preparation from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist, and data interpretation affect differently the results from each of the methods. Significant differences in analysis results from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All these studies point to the need for reliable quartz analysis methods. In a recent research, a procedure for preparing bulk coal and host rock samples for quantitative quartz analysis was developed. Further the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle size distribution, matrix, and calibration on analysis results. In this paper, several issues with the measurement of quartz in the samples of coal, host rock, and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1994

By S. K. Sharma

The Bureau of Mines' Tuscaloosa Research Center is conducting research to develop a basic understanding of solid-liquid separation in order to improve the dewatering of fine particle slurries. In the present investigation capillary suction time (CST) of kaolin slurries was determined. The average specific resistance of the cake was also determined by fitting the CST data to the theoretical equations used in this paper. The experimental data were analyzed by a powerful computer-based method, chemometrics, that uses statistical techniques to remove error and to find the number of physically significant factors contributing to the data. Results showed that two significant factors explain the CST data.

Jan 1, 1991

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By J. Wiedenroth

Since the end of the 1970s Pipe Conveyors have become increasingly important for conveying bulk materials because they have some specific advantages over conventional troughed belt conveyors. FLSmidth KOCH Pipe Conveyor represent the marked-leading know how of the former KOCH Transporttechnik GmbH, which belongs to the FLSmidth Group since January 2007. Pipe Conveyors from FLSmidth KOCH are already being used successfully at more than 260 locations around the world. Their special properties, their extreme flexibility, the horizontal and vertical changes in direction without transfer points, the small space requirement, the low-noise running and their optimum protection of environment and material without any additional casing mean that Pipe Conveyors can provide transport solutions that are often far superior to other conveying systems. The utilization of these many advantages will be illustrated in the following example of the world?s longest Pipe Conveyor at Cementos Lima, the Peruvian cement producer.

Jan 1, 2010

By George Innes

The soda ash business in the United States has undergone a sweeping technological change in ihe last 20 years. In a world where synthetics are continuzlly replacing natural products, here we have exactly the opposite, a syntheric chemical being replaced by a natural product. This change is nearly complete in the U.S. and is beginning to take place in Europe and other parts of the world.

Jan 1, 1980

By G. Van Weert

Refractory ores and concentrates containing silver tend to form Ag-jarosite during autoclave oxidation. Silver extraction from the oxidation products is therefore low, unless a hot lime treatment step to decompose Ag-jarosite precedes cyanidation. Since silver iodide is very stable but soluble in cyanide solutions, the formation and decomposition of Ag-jarosite in the presence of iodine species was studied. Results indicate that Ag-jarosite formation could be prevented in favour of H3O-jarosite and AgI while oxidizing Ag2S under industrial autoclaving conditions, when the total iodine species to Ag mole ratio exceeded 5. Lower ratios gave proportionally more Ag-jarosite and less AgI. Under these conditions existing Ag-jarosite was also found to decompose in H30-jarosite and AgI.

Jan 1, 1993

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By Alex Stewart

Most iron bearing ores treated by the R=N Direct Reduction Process yield products lower in phosphorus than the initial ores. The sulfur is also removed and generally is in the range of 0.02 to 0.05 percent in the final R=N product, independent of the sulfur content of both the ore and carbon fuel used. The mechanism and thermodynamic justification of the principal reactions leading to the removal of both phosphorus and sulfur and the control of sulfur in the iron concentrate produced are discussed and supported by the results of laboratory experiments. In substantially all iron ores (containing up to 4% sulfur as sulfate) and solid carbon fuels (containing sulfur from 1 to 8%) tested, the rejection of sulfur has been in the order of 90-95%, with not more than 0.02 0.05% sulfur in the final metallic iron product. With respect to phosphorus-bearing iron ores ranging up to 0.70% P205, the rejection to tailings has been in the order of 70-95%, resulting in not more than 0.03 - 0.07% phosphorus in the final product.

Jan 1, 1958

By D. J. Torpy

With copper at its host depressed price in several years, producers are looking at every opportunity to cut costs in order to continue operating. Some of the measures that have been applied by different companies include reduction in manpower, high grading, and in some cases partial shutdowns. The most beneficial cost cutting measure implemented by Southern Peru Copper Corporation was to steepen the slope of the final pit limit from a conservative 37 degrees to an average of 48 degrees. By doing so, substantial cash outlays were saved. Southern Peru Copper Corporation (SPCC) operates two open pit copper mines and concentrators in the southern part of Peru, about 150 kilometers from the Chilean bordar. The Toquepala Mine went into production in 1960 and the Cuajone Mine in 1976. Both mines use shovel, truck and train operations. The trains, which haul ore to the crusher or waste to the dumps, are loaded either directly by shovels or by a transfer system. The Toquepala Concentrator treats an average of 43,000 tons per day and the Cuajone Concentrator an average of 55,000 tons per day. Concentrates are shipped via a 200 kilometer railroad to the port city of Ilo where the SPCC smelter is located. The annual production in the smelter from both mines is 290,000 tons of blister copper.

Jan 1, 1987

By Thomas H. Ferrigno

Modern Plastics (July, 1983) reported that about 2.2 million tons of mineral fillers were expected to be consumed by the plastics industry that year, of which 7096 was limestone derived. The combination of fillers and polymers is called a composite and, in the more general sense includes continuous and discontinuous components in a matrix. The only significant technical advance in the fillers industry has been the greater general availability of surfied (Ferrigno 1959), an acronym for surface modified, fillers. The many reasons for this occurrence will be given in detail later, but the primary reason lie with differences between inorganic filler surfaces and the polymers which bind them together to form the composite. Minerals and glasses (fiberglass, fly-ash and beads) have surface tensions in excess of 200 dynes/cm, whereas organic materials have surface tensions less than 75 dynes cm. Water has a surface tension of 72 dynes/cm and is always present as an absorbed layer on high surface tension materials to reduce the surface tension. Although almost any organic liquid or polymer has a surface tension low enough to displace the water layer, the highly polar nature of filler surfaces requires highly polar agents to produce a permanent effect, and frequently the water is so tightly bonded or so much more active that the displacement is temporary. Furthermore; the water layer causes tiny particles to adhere to each other (agglomerate) to make sepaartion or dispersion of the individual particles very difficult. The solution to these problems is then to form a chemically bonded layer on the filler surface similar to that of the polymer so that immediate wetting, dispersion and uniform distribution of the filler particles is obtained.

Jan 1, 1985

By W. H. Strickland

The research reported here characterizes ultrasonic ranging sensors for autonomous navigation on underground mine mobile equipment. Because ultrasonic rangers are inexpensive, have no moving parts, have no lenses to clean, are small and unobtrusive, and can measure distances in dusty environments, they are especially sui ted to underground mi ne environments. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of individual rangers and a ring array of 24 sensors. The results showed the sensors have good accuracy and low variability. Additional experiments at AHAX' s Henderson mine Showed the sensors could accurately and reliably measure rib features, convex and concave corners, and drift intersections. The results showed that when used and analyzed properly, the sensor data may be used reliably for underground mobile equipment navigation.

Jan 1, 1990

By M. J. Friedel

The U.S. Bureau of Mines (USBM) investigated the use of seismic refraction tomography (SRT) for identifying changes in pillar loading at the Foidel Creek coal mine near Steamboat Springs, CO. The inherent three-dimensional problem of directly imaging coal pillar conditions is reduced to a single plane by considering only the load transmitted from the pillar to the adjacent floor rock. Floor strata velocity tomograms (at two pillar locations) illustrate that loading conditions are non-uniform and non-unique. Also, time sequence monitoring, as the longwall face advanced, demonstrated that SRT can be used to image spatial changes in loading conditions. SRT offers the mining engineer a simple and flexible technique for evaluating pillar conditions, and thus, both present and alternative mine designs.

Jan 1, 1994

By Ping K. Di

A naturally aged and synthesized manganese oxide-coated granular media was found in our laboratory to have the capability of the removal of soluble Mn(H) from mine drainage by adsorption and oxidation. Mine drainage commonly also includes other heavy metal ions. Extending this principle, this paper presents the removal of heavy metals including lead, copper, cobalt, zinc and nickel in the aqueous solution by using the synthesized manganese oxide-coated granular media. It was found that the adsorption of lead, copper, cobalt, zinc and nickel on the manganese oxide-coated media follows both Langmuir and Dubinin-Radushkevich adsorption isotherms except in the concentration range less than 0.1 mmole/L. The adsorption mechanism involves the ion exchange between the heavy metal ions and synthesized manganese oxide coated on the media. The synthetic manganese oxide surface has a strong metal binding ability to the heavy metals in the order of Pb2+ > Cu2+ > Ni2+ > Zn2+ > C02+ based on the adsorption results using batch and continuous column operations. The breakthrough curves of these heavy metals showed that the synthesized media could be used effectively in the removal of these heavy metal ions in a cell or packed column. The process can simultaneously facilitate the immobilization of the heavy metals on the synthesized manganese oxide coated media. A subsequent pH adjustment dislodges the heavy metals and regenerates the synthetic media. Thus, the process accomplishes the adsorption, immobilization and concentration of the heavy metal from waste stream in one monolithic procedure.

Jan 1, 1995

By John J. Dran

Large mining companies use a number of sophisticated analytical techniques for introducing the element of risk into the valuation of mineral reserve sites. These methods include, but are not limited to, sensitivity analysis, computer simulation, conditional probability, and portfolio theory. Such techniques enable the managements of these large companies to have an awareness of the many possible ramifications of their investment decisions. On the other hand, small mining companies and individuals in the mining business, due to limited financial and technical resources, still rely primarily on single point estimates of the value of mineral reserves. These small miners introduce the aspect of risk only through the application of an appropriate "speculative" discount rate. This paper illustrates the application of a technique for the introduction of risk into investment analysis. The method appears to be most suitable for use by small mining companies and individuals contemplating a large investment in a new mineral reserve site.

Jan 1, 1974

By M. I. Dobrynina

At the beginning of the 80-s the first diamond pipe in the East-European platform was discovered in the North of the Russian Federation on the White Sea Winter coast. During several years while studying this unique area data on kimberlites and country rocks petrophysical characteristics have been collected. Considerable experience in geophysical methods when searching and exploring diamonds was accumulated, and various methods of geophysical data interpretation were used. It has been established from the analysis of geophysical data that diamond-bearing kimberlites are located in the most ancient and the most stable block of the East-European craton.

Jan 1, 1995

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

By Z. Man, X. Zhu, Y. Xian, Y. Tao

"Fine coal separation has been always concerned. The froth flotation is not efficient in desulfurization because of the low rate of sulfide liberation from raw coal, the natural hydrophobicity caused by sulfur concentration on the surface of sulfide, and the presence of large amounts of middling feed. An efficient centrifugal gravity separator was employed to separate for Shandong –0.5mm high sulphur coal, the partition curve of centrifugal separator was obtained with conclusion that the Ecart probable error value of the separator is 0.095, the imperfection I value is 0.128. Finally, comparing with the coal flotation using progressive release method, the result shows that the effect of the desulfurization with centrifugal gravity force field based on density difference between coal and minerals are much better than that of the floatation which operates based on the difference in surface properties. It provides a efficient technical way for fine coal separation. INTRODUCTION Coal plays the most important role in the energy consumption in China. Although natural gas, wind energy, nuclear power has made great progress in recent years, but the share of coal in the final energy consumption accounts for 70-80%, which is determined by energy storage of China. Under the requirement of environmental protection, the clean utilization of coal resources becomes more and more important, and the need has already been identified. Coal washing and processing plays an important role in the process of high-efficiency and clean utilization of coal. For the separation of fine coal, flotation is a traditional method for effective separation and has been used in large scale industrial applications in coal preparation plant. However, for the separation of difficult-to float coal, especially fine oxidized coal and low–rank coal with hydrophilic surface, flotation is usually inefficient [1-3]. Although many pretreatment methods have been adopted, including grinding, microwave pretreatment, new flotation reagents, the problem of efficient separation has not been completely resolved [4-6]. Thus, an enhanced gravity separation method using particle density difference rather than hydrophobic difference was proposed for the separation of fine coal. Many research results have proved that this is a practical and effective method of sorting. R.Q. Honaker used Falcon C10 concentrator, Knelson centrifugal separator and spiral separator to clean the fine coal with size of 600*210 µm and 210*37µm, the effects of different operating parameters on the separation index was discussed. The results show that the separation density of Falcon can reach 1.6, and the Ep value can reach 0.1-0.15. This paper revealed that for the separation of fine coal with high sulfur content or fine grained content. Falcon has high separation efficiency with low cost. Separation results present in another paper showed that the desulfurization efficiency of inorganic sulfur was better than that of flotation [7-8]."

Jan 1, 2017