Search Documents

"The adsorption of mixed cationic/anionic surfactants with different molar ratios onto quartz was investigated. The cationic surfactant used was dodecylamine bromide (DDA), and the anionic surfactant was sodium oleate (NaOL). The critical micelle concentration values for the individual surfactants and their corresponding mixtures were determined using a platinum plate. The adsorption mechanisms of mixed surfactants on quartz were studied using contact angle measurements, flotation tests and adsorption amount measurements. At alkaline condition, NaOL depresses DDA flotation of quartz without depressing the adsorption of DDA. The molar ratio of mixed surfactants is found to be a key factor in the orientation of alkyl chains and thereby the flotation response of quartz. A mixture of 1/2 or 1/3 DDA/NaOL forms on the surface of quartz when the concentration of NaOL is higher than that of DDA. The adsorption of the mixture decreases the wetting of quartz since the alkyl chains are in chaotically orientation with a conceivable number of head groups directing towards the solution phase. These results provide important insights into the adsorption of mixed surfactants onto quartz surface. INTRODUCTION Froth flotation is known as an effective method of separating mineral particles on the basis of their surface chemistry, specifically their hydrophobicity. [1]. The hydrophobic particles will attach to the bubbles and rise to the top of the containing vessel to form a froth that flows over the lip of the vessel. The hydrophilic particles remain in the liquid [2]. In the process, surfactant is often used as collectors for surface modification in order to change the wetting properties of mineral particles. The primary long chain alkyl ammonium salts are the most widely used as collectors for the flotation of oxide minerals, such as quartz, muscovite, hematite, phosphate and feldspar [3, 4]. Adsorption mechanism of alkyl ammonium salts on oxide minerals has been extensively analyzed [5, 6]. Generally, the ammonium salts are adsorbed through electrostatic interaction of the polar group of the molecules with the surface of these minerals [7]. Despite many obvious advantages of the ammonium salts in low temperature resistance and hard water resisting, however, their unavoidable drawbacks, such as high sensitivity and poor selectivity for slimes, relatively high cost, have limited their applications [8]. In recent years, mixed surfactants have drawn much attention due to their superior physicochemical and surface properties than single surfactants [1, 9-11]. They have been used in many industrial processes such as dispersion/flocculation, flotation, detergent, corrosion inhibition, cosmetics, foods, paints, chemical mechanical polishing, enhanced oil recovery, and nanolithography [12]. Most of the mixed surfactants have synergistic advantage in reduction of the surface tension and critical micelle concentration (CMC); therefore, they exhibit spurious properties, like excellent surface/interfacial activities, and are less expensive than single mixed surfactant systems [13, 14]."

Jan 1, 2016

By Alfred L. Anderson

Thorite and rare earth deposits in the Lemhi Pass area of southeastern Lemhi County, Idaho, are contained along complex shear and fracture zones and in reopened gold-quartz veins and copper lodes in quartzitic and phyllitic rocks of the Pre-cambrian belt series. Some of the shear and fracture zones are several tons of feet across and comprise broad zones of irregularly mineralized rock. These lodes contain a notable concentration of thorium and rare earth elements along with considerable amounts of barium, .potassium, calcium, iron, aluminum, phosphorus, sulfur, and silicon. The principal minerals are thorite, locally allanite, monazite, xenotime (?), apatite, specular hematite, barite, potash feldspar, occasionally calcite and quartz. Exept for some of 'the specular hematite, barite, reddish feldspar, calcite and quartz, the minerals are not distinguishable without the microscope. The thorite and locally allanite were deposited first, then the monazite and other phosphates, which were in turn followed successively by barite, potash, feldspar, calcite, and quartz. In exceptional cases, deposition of thorite and specular hematite was repeated after the feldspar. Some of the deposits contain several percent thoria, but the average os generally under one percent. The rare earth content is comparable with that of the thoria. The deposits appear to be of hydrothermal origin and are probably related genetically to late Cretaceous or early Tertiary igneous activity, manifested locally by a few dioritie and lamprophyric dikes.

Jan 1, 1959

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

By B. K. Parekh

Sludge obtained during production of magnesium (Mg) metal from electrolyzing of molten MgCl2 contains entrapped magnesium particles. The sludge material containing the magnesium particles is a friable, continuous matrix of frozen salt mixture which may also contain some oxides and impurities. A dry process was developed for recovery of magnesium metal from the sludge, utilizing minerals beneficiation unit operations. The steps included selective comminution, screening, attritioning and tabling. Recovery of the high grade (+90 percent) metal was in the 70 percent range. The process is being commercially used in the U.S. The novel process was also successfully applied to a magnesium-alloy for recovery of metal from the sludges.

Jan 1, 1995

By W. E. Lamont

As part of its program to minimize mineral and metal needs, the Federal Bureau of Mines conducted investigations to determine the feasibility of producing foundry-sand-grade olivine concentrates from low-grade sources. Using a Bureau-patented attrition-grinding technique, concentrates meeting Steel Founder's Society of America (SFSA) specifications for loss on ignition (LOI) were prepared. Studies showed that green strengths and tensile strengths of the attrition-ground olivine were equivalent or superior to those of commercial materials. Metal-casting studies showed that molds of attrition-ground olivine produced better surface finishes. The improved surface finishes were attributed in part to increased grain sphericity.

Jan 1, 1977

By Hamid Maleki

This paper reviews a study conducted for Australian Coal Research Limited (ACARP) to assist Anglo-American operations with better understanding of coal burst mechanics and control based on U.S. practical experience, investigations, and inspections in three major U.S. coalfields over the past 45 years. The study examined both nonviolent and burst-prone case studies to identify contributing risk factors and addressed failure mechanisms for major U.S. coalfields in Utah, Colorado, and Kentucky, which have diverse characteristics. To investigate the mechanics of coal burst, a multipronged approach is used. First, field measurements in three mines from East Mountain, Utah, are complemented with finite-difference stress analyses to address the importance of horizontal stress in coal pillar mechanics of violent failure. Second, the computational procedures for estimating seismicity resulting from slip along geological discontinuities are reviewed, as these measurements point to seismicity being the trigger mechanism for violent failure of marginally stable structures. This joint-slip seismicity mechanism is in agreement with the more recentimproved re-examination of mining-induced seismicity (MIS) data from the Crandall Canyon Mine, Utah by University of Utah (UOU). Third, a hybrid statistical-analytical methodology is applied for identifying significant factors affecting coal burst. It utilizes data from 30 case studies including those from Utah, Colorado, Kentucky, and other eastern U.S. mines. The statistical approach reinforces field measurements and points to strata rigidity, joint spacings, and horizontal stress field as significant factors affecting damage resulting from coal bursts. This provides practical capabilities for identifying operations of higher risk using a rigidity-cavability variable. Overall, the study provides valuable insights into the mechanics and risk factors associated with coal bursts in major U.S. coalfields. By utilizing a multipronged approach that incorporates both field measurements and statistical-analytical calculations, the study offers practical capabilities for identifying operations of higher risk and improving coal burst control.

Jul 1, 2023

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By Sureshan K. Moothedath

This paper provides a mechanistic representation for floc formation, growth and degradation and presents results from an experimental study of batch flocculation in which step changes were made in the impeller speed, flocculant addition, and slurry concentration. A discussion of the experimental results is included in terms of the mechanisms of floc formation and size-change.

Jan 1, 1993

By J. P. Matoney

In recent years, the diminishing supply of natural gas has led energy suppliers and consumers to consider making synthetic natural gas from coal. A number of processes have been devised to produce gas from coal; many of these have been operated at the pilot stage and some have been operated commercially. Each process has specific coal feed stock requirements with respect to size consist and moisture content. The purpose of this presentation is to compare the estimated costs for coal handling, live storage, size reduction and drying facilities that would be required for delivery of coal feedstock to different gasification processes.

Jan 1, 1977

By X. Song, Q. Zhang

"The development of fracture zones in surrounding rock mass has significant impact on the stability of underground mine roadways. Detection of the fracture zones is of compelling importance for maintaining roadway stability as well as for safe and speedy excavation of the roadways. This paper presents a study conducted at Dong Bao Wei underground coal mine, where the roadways were developed in diabase rock mass. The roadways suffered severe damages, including sloughing and excessive floor heaving. The borehole imaging technique was applied in the study to observe and detect fracture zone development surrounding the roadway openings. Based on the borehole imaging studies, new roadway support systems were proposed to improve the stability. INTRODUCTION At the Dong Bao Wei Coal Mine three main roadways of the west wing were excavated. The three roadways had semicircle arch cross sections and were at a depth of 650 meters, each being about 750 meters in length. The roadways were driven through a section of thick diabase intrusion, which was softened by water with reduced strength and may turn into powder form under weathering. Site investigation indicated that the roadways in diabase intrusion zone were badly damaged due to severe deformation, and very serious roadway sidewall sloughing and spalling accompanied by severe floor heave often occurred.(Figures 1 and 2) In order to ensure the normal use of the roadway, undercuts were excavated. However, this operation seriously affected the roadway construction progress and increased the amount of roadway support operations as well as the roadway maintenance costs. Furthermore, a roof fall accident occurred in nearby drilling site. The investigation indicated insufficient support provided for the roadways which imposed significant safety hazards and would have serious impact to mining production and subsequent mining activities.The support of the main roadways is a critical task and is the focus of the underground opening excavation work at the mine, since more than 40 years of service life is required from these main roadways. For these roadways, large cross sections with high degree of stability and minimal amount of deformation should be maintained. Therefore, providing sufficient and appropriate roadway supports is of significant importance to the coal mine. In this paper, in order to optimize the roadway supporting system, studies were carried out on the geological structures, lithological characters, roof bolt anchoring features and suitable anchoring layers. The studies were aimed at ensuring the stability of mine roadways, reducing the roadway maintenance costs and providing a safe mine passageway for orderly production and progressive development of the mine"

Jan 1, 2016

By M. L. Smith

SAG mill throughput is often a bottleneck in increasing metal productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility which is also relevant to the rock fragmentation that is achieved by blasting. The relation between the size distribution and fragility of the feed and of the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1993

By Jian Deng, Hehua Zhu, Lianyang Zhang

Rockburst is defined as a sudden and violent explosion of rock on the surface of a rock excavation. Rockburst has been regarded as the least understood and most feared hazard problem for underground rock excavations. Traditionally, rockbursts were classified into the strain, pillar, and fault-slip categories. However, rockbursts are also known to occur at stress levels well below the rock yield strength, in mines where the rock is far from brittle, or without the presence of geological discontinuities. A plausible explanation of rockbursts is buckling, which has been identified as one of the main mechanisms for rockbursts. It is observed that rockbursts are often induced by dynamic loadings (pulses) from adjacent blasting. Therefore, the present paper studies the effect of pulse shape and amplitude on pillar rockbursts induced by dynamic loadings from blasting using the method of numerical analysis. The governing equation of a pillar’s motion is set up and the mechanism of pillar rockbursts is investigated through a practical example. The results show that it is not the shape of a pulse but the impact energy to decide the occurrence of pillar rockbursts. If all other parameters remain the same, pillar rockbursts are more likely to occur when the pulse duration is longer. The parametric resonance and the perturbation of dynamic loadings are also found to play an important role in the occurrence of rockbursts. These insights would provide invaluable clues about the mechanism and for better control of pillar rockbursts.

Apr 26, 2022

By B. R. Pothini, H. von Schonfeldt

In underground coal mining many excavated openings have a relatively short projected life span. To ensure safety for men and materials at a minimum cost over the projected operating life, only pillars for overburden support and roof bolts for support of the openings are used extensively. Mining activity constantly changes the geometry of the mine producing load changes on the structural support members of the openings that often induce unstable deformations which can lead to roof falls or pillar failures. The paper describes how simple deformation measurements can be used to design primary and supplementary roof supports and to predict roof falls and possibly pillar bumps. Specifically, bed separations in the roof measured directly with the help of borescopes and calculated from differential convergence data are used to optimize bolt links or support requirements for chemical stabilization of mine roofs. Roof falls are predicted on the basis of admissible values for cumulative convergence between roof and floor, convergence rate, and the change of the rate of convergence. The pillar extraction operations convergence anomalies detected from contouring identify bump prone pillars, while convergence and pillar dilation determine the yield zone in a pillar to verify pillar softening and de-stressing. Manuscript not received in time for publication.

Jan 1, 1983

By V. G. Lofftus

Since plant start-up in January 1983, Golden Sunlight Mines, Inc. has implemented several process changes and improvements. Among these are a pulp preaeration circuit and a sand tailings retreatment circuit. The purpose of the preaeration circuit is to reduce reagent consumption during gold dissolution. The sand tailings retreatment circuit was added to recover and process separately pyrite concentrate to maintain acceptable overall gold recoveries with the more refractory sulfide ores. Research and plant operating data along with process and improvement descriptions are presented.

Jan 1, 1987

By H. Shafick Hanna

The beneficiation characteristics of low grade Birmingham red iron ores of the Big Seam and Ferruginous Sandstone seams were investigated using flotation and magnetic separation after reduction roasting. Samples of Bib Seam Ore responded more readily to concentration than the Ferruginous Sandstone ores. The impurities inherent with the iron oxide minerals limit the grade of concentrates recoverable from these ores to a maximum of about 61% Fe if reasonable iron recoveries are sought. Flotation concentrates assaying 60-61% Fe and about 0.1% P with attendant iron recoveries of about 63% were achieved from Big Seam ore charges while those obtained from the low phosphorus Ferruginous Sandstone samples analyzed 54-56% Fe. Reductive roasting and magnetic separation of ground charges of the two ore samples yielded concentrates assaying 60-61% Fe. Iron recoveries were better than those achieved by flotation, but the magnetic products of Big Seam ore were high in phosphorus (0.2-0.3% P).

Jan 1, 1983

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By Christophe Bragard, Rebecca Reeve

The Regional Connector Transit Corridor (RCTC) Project is a 1.9-mile-long metro light-rail extension project that traverses the historical core of downtown Los Angeles, California. This project aims to improve mobility throughout downtown LA with fewer transfers for riders. It is designed to connect two existing rail lines for a more seamless travel. The project consists of twin bore tunnels, three new stations, and is scheduled to be completed in 2022. The design-build contract was awarded to the Regional Connector Constructors (RCC) in 2014, a joint venture of Skanska and Traylor Bros, Inc. with Hatch Mott MacDonald as the designer. One of the challenging aspects of the project was the construction of a crossover cavern in a narrow public right-of-way surrounded by historical structures. RCC used Sequential Excavation Method (SEM) to construct the crossover cavern measuring 287 ft long by 58 ft wide by 36 ft tall. The initial lining of the cavern featured a 12 in. fiber reinforced shotcrete lining. The initial lining was separated from the final lining by a hydrocarbon resistant membrane, as specified by the standard requirements of Metro. The cavern features a cast-in-place final lining with a thickness of 5 ft 9 inches in the invert and 18 inches in the crown and walls. The structure also features a nonload bearing plenum slab and interior walls for ventilation.

Jun 13, 2021

By L. Alagha, M. Khodakarami

"This work focuses on the extraction of rare earth metals (REE) from aqueous solutions using stimuli-responsive polymers. Various parameters affecting the adsorption capacity of the polymer, including pH, polymer concentration and REE concentration were studied. The interfacial behavior of REE in aqueous phase before and after polymer addition and the mechanism of the formation of metal-polymer complexes and their properties were investigated using UV/VIS spectroscopy. Results obtained would help to test the feasibility of employing stimuli responsive polymers in pre-concentration of rare earth elements associated with other elements in mineral aqueous streams prior to solvent extraction. The pre-concentration step would reduce the amount of organic solvents used for extraction and striping compared to conventional extraction processes. INTRODUCTION Rare earth elements (REEs) have become the foundation for several technologies and have been used extensively in many industries such as modern electronics, green energy, health care and transportation and defense [1-4]. As these industry sectors are growing, the global consumption of REEs is going to increase dramatically. The current global REEs demand is estimated to be 105,000 tons of rare earth oxides per annum with an expected annual growth of 5.6% [5-6]. Rare earth elements are produced from different sources (primary and secondary). China is considered as the largest producer of REE in the world, providing about 90% of the world’s mine production while the United States is second with 4% of the mine production [7]. High global demand for rare earth materials results in shortage of such materials in the near future. It should be considered that the term ‘‘rare’’ earth is not an accurate term, since they are abundant in some extent in the Earth’s crust, but are typically finely dispersed. Thus, nowadays looking for more efficient and cheaper methods for extraction, separation and purification of low concentrated REE ores and exploring secondary sources are essential. Rare earth materials are found in raw condition and require treatment that involves several processes, which can consume money and time. Recent improvements in extraction and recycling technology have made the extraction of rare earth elements from rare earth sources more feasible in terms of cost and time [8-10]. Physical and pyrometallurgical methods require high-energy and thus high costs. Moreover, due to environmental problems, environmental protection systems are required, and they are not as adaptable as chemical processes [11, 12]."

Jan 1, 2016

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for expensive large-scale tests that are currently being used. A radiant panel apparatus was used to determine the relevant thermal characteristics of the materials: time to ignition, critical heat flux for ignition, heat of gasification, and mass loss rate. Three thermal parameters, TRP, TP1, and TP4, were derived from the data, then were developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with thermal and ignition hazards of similar materials reported in the literature and represent a simpler approach to quantifying these combustible hazards. INTRODUCTION The potential fire hazard from combustible mine materials is a major concern that can impact the safety of mine workers. Combustible materials tend to be solids and within this category there exist degrees of flammability and fire resistance. These materials may be readily ignitable or they may be able to withstand high temperatures and high heat fluxes. Presently, no simple methodology exists to assess these possible fire behaviors and quantify the resultant fire hazards. Thus, better knowledge of the thermal properties and chemical characteristics of combustible materials is of great importance to the safety of mine workers. Tewarson [1994] developed a methodology which he subsequently used to evaluate the ignition and fire resistant properties of combustible mine materials, but these efforts are more than 20 years old, and do not include many of the new materials used in mines today. The standard practice that has evolved for a combustible material to be approved by the Mine Safety and Health Administration for use in underground coal mines is to conduct extensive and costly large-scale experiments on each new material that is used in a particular mine operation. Results of such tests provide pass/fail answers to the questions of a material’s flammability or fire resistance, yet they provide little, if any, information that will lead to a better understanding of the basic mechanisms involved. Therefore, there is a need to quantify material flammability properties and to develop a methodology to rank the ignition and fire hazards of commonly used underground mine materials. During the heating and ignition stages of combustible materials, properties such as smolder susceptibility, minimum surface temperature for ignition, thermal conductivity, heat capacity, density, and heat of gasification are known to be important [Apte, 2006]. During the flaming stage, additional parameters, such as the heat of combustion, heat release rate, flame spread rate, yields of soot/smoke, and toxic gas production become more important as the flame is sustained and spreads. In very general terms, the heat flux incident on the surface of a solid combustible not only controls the rate of temperature increase of the local fuel surfaces, resulting in expulsion of fuel vapors that sustain the flaming process, but also the heating of other combustible surfaces that subsequently ignite and spread flame."

Jan 1, 2015

By E. E. Maurer

Kerr-McGee has operated the Ambrosia Lake uranium mill since startup in 1958. Tonnage milled per day has varied from 3500-7000 tons. The mill capacity is currently rated at 7000 tons per day. The process consists of two parallel circuits following crushing and sampling, \\lhich include open circuit rod mill grinding, sulfuric acid leach, cyclone classification, and counter-current washing circuits of sand classifiers and slime thickeners. Pregnant solution is clarified and polished by precoat pressure leaf filters prior to amine solvent extraction. Yellowcake is precipitated from the pregnant strip solution with ammonia, filtered and dried.

Jan 1, 1972