Search Documents

By D. I. Hoyer

A preliminary model has been developed for autogenous pebble milling using information obtained from studies on ball milling and SAG milling. The model treats the breakage as the weighted sum of first-order breakage of smaller particles by tumbling pebbles, non-first order breakage of larger particles which are too large to be nipped properly by pebbles, autogenouS fracture and chipping of larger lumps to form pebbles, and autogenous fracture and abrasion of pebbles. The model includes the effects of residence time distribution, classification through the exit grate, and a mass transfer relation which describes the accumulation of fine material in the mill. Example simulations are given, based on breakage parameters determined from batch grinding tests in laboratory mills. fracture breakage and abrasion. In the development of these preliminary mass balance equations it will be assumed that breakage by fracture is first-order, but this assumption will be modified later in the paper. It will also be assumed that the residence time distribution of a long autogenous mill can be described by an equivalent series of m fully-mixed mills, with a classification action imposed on the mill contents by the discharge grate. Size distributions are expressed as a v2 geometric series, numbered 1 for the top size down to n for the fines, or "sink" interval. If the holdup in the mill is W then the rate of breakage of material in size interval i is given by SiwiW, where wi is the fraction of material in size interval i, and Si is -the overall specific breakage rate of size i material (fraction per unit time).

Jan 1, 1985

By E. Maré

Some of the members will probably ask themselves what close relationship exists between hydro-metallurgy and a wet scrubber, but we are sure that as soon as deeper thought is given to the matter it will be realised how vital scrubbing, operations are in metallurgical plants. In ordinary metallurgical installations or pyro-metallurgical processes ore concentrates are first of all shifted from place to place and dust is created. In other cases the ores or concentrates are crushed or dried or roasted, and in each one of these operations dust and fumes, are created. All suspended particles and fumes originating from the abovementioned conditions not only, in many instances, provide health hazards which disrupt production and endanger the personnel in the plant, but also are the source of economic losses through extra maintenance and wear to moving machinery due to abrasion and corrosion. Further losses are incurred by the waste of fine, very often valuable, components. The Party who once said that in several metallurgical plants the bulk of the profits was discharged into the atmosphere by the stack wasn't stretching the truth. There is a place in Africa where a gold producing concern used to lose over 5 oz. of fine gold per day out of a total production of 3000 oz. per month. In another instance, copper concentrate going as high as 80% Cu was discharged into the atmosphere at the rate of 4 tons per day. Realising the value of removing and collecting solids and fumes created in metallurgical plants, a thorough study was made of the available plant and equipment offered on the market. Some units were found very efficient, but very expensive; some others also very efficient but with temperature and maintenance limitations. Some others were also efficient but prohibitive from the point of running costs.

Jan 1, 1963

By Dennis S. Kostick

Sodium is a silver-colored metal that is so unstable that it reacts violently in the presence of water, and chlorine is a greenish-colored gas that is dangerous and lethal. Yet the combination of these two elements forms sodium chloride, commonly known as salt, which is a white-colored compound essential to life itself. Salt is perhaps the only mineral in the world that is used virtually by every human being in every country. Although its importance has diminished over time, salt has had a profound influence on history. Sources of salt have determined the location of cities, such as Salzburg, Austria, Salzgitter, Germany, Salt Lake City, UT, and Saltville, VA. Populations have migrated in search of salt, and wars have been fought to obtain or to protect it. Although there is no written record of when prehistoric man first discovered salt, he probably instantly appreciated its unique and distinctive taste and sought more of it. He noticed animals were attracted to salt springs and salt licks, where they satisfied their innate cravings. Man used this knowledge to hunt for food; where he found the salt, he would find the animals. Because prehistoric man was not aware of his physiologic need for salt, he automatically received his salt requirements from the meat of the animals he ate. A Mesopotamian tale tells of a wounded pig that ran into the ocean and drowned. After being recovered from the ocean, where it was saturated in the salt brine, the pork was found to taste better than unsalted meat. It was not until man graduated from a nomadic to an agricultural society when he introduced vegetables and cereals into his diet that he realized he needed additional supplements of salt. The Sumerians ate salted meat and used salt to preserve food about 3500 BC. In approximately 1000 BC, the Trojans learned to use salt for preserving fish. The maritime civilizations, such as that of the Phoenicians, engaged in an extensive salt trade throughout the Mediterranean. Many superstitions, customs, and traditions surround the religious, social, economic, and political aspects of civilization. Although some commodities have provided the basis of some ageless metaphors and cliches (i.e., heart of gold, strong as steel, etc.), none are more commonly used than those pertaining to salt. Being "the salt of the earth" referred to a person's worthiness, as referenced in Matthew 5:13 of the Bible. Someone "not worth his salt" reportedly was used in ancient Greece in bartering salt for slaves. When a laborer was worth his salt, he was paid a salary (sal is Latin for salt), a term still in use today that dates back to Roman times when part of a soldier's pay was salt rations. Fearing those around him, the Roman leader Pompey was known to add a grain of salt to his drinks as a supposed antidote to poison. Hence, "taking it with a grain of salt'' is to regard something with suspicion. The earliest known record of salt production was in China about 2000 BC when Emperor Yu decreed that salt had to be supplied to the court as a tribute. Because salt was a commodity that had universal demand, governments often intervened to control salt production and distribution to generate revenue for major national projects. State-run salt monopolies were common in history, such as in Rome about 506 BC. Revenue was also derived from taxes levied on salt sales. The word gabelle refers to the direct salt tax used in France. This tax was so despised that it was a major cause of the French Revolution. Although the tax was repealed in 1790, it was reinstated in 1805 to raise revenue for war. France continued to used the gabelle until 1945. Salt making was an important economic activity in many areas of the world. Archaeological evidence indicates that salt was quarried from hills near the Dead Sea before the Bronze Age. At Hallstatt in the eastern Alps of Austria, rock salt was mined as early as 1400 BC. Solar salt was being produced in the northern Yucatan peninsula by the Mayan civilization from about 50 BC to AD 300. Other than the prehistoric use of salt in the southwestern part of the United States by the Native Americans, the first production of salt by American colonists began in June 1614 on Smith's Island, VA, seven years after the founding of the Jamestown colony. The short-lived activity was in response to the high price of salt being charged by ship's captains who brought salt over as ballast from England. Although Nathaniel Loomis is credited with starting the first commercial inland salt production in the United States at Onondaga Lake in New York in 1790, salt had been made by individuals for private use years earlier. Indians had long known of the salt springs in the Kanawha Valley of Virginia (now known as West Virginia). In 1755, Mary Ingles, a white settler, was kidnapped by Indians and was forced to make salt from the saline springs. After her escape, she told other settlers how to make salt. At Saltville, VA, Arthur Campbell began making salt in 1782 by boiling brine obtained from salt springs. In 1799, William King sank a shaft about 3 m in diameter down about 61 m to the underlying Saltville salt deposits. The shaft flooded before he could extract any rock salt; however, King has the distinction of digging the shaft of the first salt mine in the United States. Fig. 1 shows the King site as it appears today in Saltville, VA. Production of brine from the shaft continued until 1892. Settlers moved into the Kanawha Valley in 1785, but it wasn't until 1806 that Elisha Brooks established the first commercial salt works in Kanawha.

Jan 1, 1994

By Rick Wright, Gregory L. Raines

San Diego’s need to access underground space has dictated a long history of tunnel construction. The subsequent need for water, coupled with San Diego’s natural attractiveness, has led to significant population increases and the need for the construction of even more tunnels. This paper will provide a historical summary of the progression of mines, tunnels and trenchless technology construction projects that contributed to the advance of current technology, feasibility, and constructability. A bibliography of relevant reports and data is included.

Jan 1, 2001

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

By Osvaldo A. Bascur, J. Pat Kennedy

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. The lack of an integrated approach makes the profitability of metallurgical plants lag behind that of other industries despite technical advances that have occurred in recent years. This results in significant deterioration in the ability to maintain a "smart” operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. Combining real-time infrastructure with portal technology is becoming an accepted methodology. This paper introduces real-time portals and team sites to support decision making by work- groups which require both real-time and documentary information from manufacturing assets, vendors, head office and the Internet. Workers get insight from the overall process effectiveness index based on key variables such as losses due to plant availability, performance efficiency and rate of quality. Real-time portals and smart clients are part of any real-time performance management (RtPM) solution. Three case studies in large metallurgical complexes are presented. PLANTS ARE YOUR STRATEGIC HANDICAP Information technology is arguably one of the fastest moving technologies used by the mining/metallurgical industry. However, the business model for managing that

Jan 1, 2004

By A. Kepeski

Cement industry relies heavily on the control of large volume of raw materials in the proximity of plant operations for clinker and cement manufacturing. These mineral resources are perhaps considered as ?low-profile? (mostly comprise limestone's, clays, marls and sands), but their availability, accessibility and suitability ? the later with respect to chemistry, mineralogical and physical characters ? are factors of paramount importance and may largely affect production cost and plant productivity. The combination of scarcity of good quality raw materials deposits and the growing environmental concerns have challenged the cement producers towards sustainability and the responsible exploitation of natural resources. In open pit mining and quarrying, the evaluation of mineral resources vs. handling of the non-usable overburden and other off-spec materials directly affects the medium to long-term production planning, quality control practices and environmental management. It is a general trend for many cement producers and a usual case for a number of Titan Cement plants worldwide, that redesign of quarry pits is necessary not only for stability purposes but also as a result of environmental constraints and emerging issues. The material reserves then have to be re-evaluated in the light of the new final pit design, safety distances from houses, other infrastructure and Law restrictions and according to criteria of safety of operations, reduction of environmental impacts, pit optimisation and proper future reclamation. The paper discusses the case of three active quarries of Usje Cement Plant, in Skopje (Macedonia), namely Usje (marl), Goverlevo (lime-stone) and Ljubosh (sand), where a large campaign of redesign and evaluation of recoverable reserves and the needs in rehabilitation took place in 2004. Technical and environmental issues and criteria are presented in the form of master plans and the highlights of the first attempts to propose and apply a reclamation scheme are discussed, by also examining alternative solutions for each quarry area. Finally, the 2005 progress in applying changes to the design of benches and pit layout, as well as experiences gained, are discussed.

Jan 1, 2005

By Dermot M. Ross-Brown

The objectives of this generic study were to use numerical modeling techniques to determine under what conditions seismic waves generated by an earthquake might cause instability to an underground opening, or cause fracturing and joint movement that would lead to an increase in the permeability of the rock mass. In general, the study showed that moderate earthquakes (up to 0.41 g) did not cause instability of the tunnel or major fracturing of the rock mass. An artificial rock-burst tremor with high accelerations, however, was found to be amplified around the tunnel, and fracturing occurred as a result of the seismic loading in salt and granite. In shale, even moderate seismic loading resulted in tunnel collapse.

Jan 1, 1981

By James A. Finch, Xiang Zhou, Yue Hua Tan

Methods to determine frother functions, control of bubble size and froth properties, are now widely used. Some collectors also exhibit frother functions which are less understood. Using a water-air system in a mini-mechanical flotation cell setup, this paper determines bubble size and water overflow rate for three amine collectors: one primary amine (dodecylamine, DDA) and two commercial ether amines (Flotigam® EDA and Flotigam® 2835-2L) and their combination with two common frothers, MIBC (methyl isobutyl carbinol) and PPG 425 (polypropylene glycol, molecule weight 425). Compared to the frothers, the amines were less effective in reducing bubble size, giving larger minimum size and the two commercial amines showed evidence of coalescence at low concentration. In blends, at fixed frother dosage, frother eliminated the coalescence but as amine concentration increased the amines dominated bubble size. Water overflow was a strong function of reagent type. For fixed 1-cm froth depth, PPG 425, Flotigam® 2835-2L and to a lesser extent DDA produced overflow while MIBC and Flotigam® EDA did not. In blends with frother overflow increased except with Flotigam® EDA. Mechanisms are briefly explored. The principal benefit of blending identified is the elimination of coalescence if residual concentration of the two commercial amines is below ca. 10 ppm.

In order to overcome some of the deficiencies associated with conventional fine coal cleaning methods, a novel process known as microbubble column flotation (MICROCEL?) was developed at Virginia Tech. This article provides an overview of recent commercialization efforts and in-plant testing of this technology. The results of the in-plant test work indicate that the MICROCEL technology offers several advantages for the upgrading of difficult to clean coals. The test data have also been used to develop guidelines for the design of coal flotation columns and to validate existing scale-up procedures.

Jan 1, 1991

By Leena Suopajärvi, Karin Käär, Marcin Szumny, Jari Joutsenvaara, Md Ariful Islam, Helmut Mischo, Georg Meissner, Ossi Kotavaara, Catalina Vrabie

This study outlines implemented tactics and results for community empowerment through participation in questionnaire surveys, educational programs, and discussion on sustainable sourcing from new critical raw materials (CRMs) projects. Utilising questionnaire surveys, including the Public Participation Geographic Information System (PPGIS), the research gathered public opinions from Estonia, Germany, Poland, and Zambia, receiving 1,068 responses. These responses addressed various social, economic, and environmental issues related to CRM projects. Feedback from educational courses with participants from over 25 nations and public events provided additional insights. The collected data and feedback offer crucial input for advancing sustainable and responsible CRM sourcing strategies in these regions.

Feb 1, 2025

By James Donald Forrester

JAMES DONALD FORRESTER 32.1-EXAMINATIONS The field examination of a mineral deposit or mining enterprise requires a comprehensive effort to determine all natural and man-made factors bearing upon the problem to be resolved by the investigation. Therefore, the purpose to be served by an examination must be fully understood before the engineer assumes responsibility, and before actual field work starts. A clear understanding facilitates planning the approach to the project for maximum efficiency and thorough acquisition of information. It follows, of course, that the engineer has the necessary knowledge and experience to discharge satisfactorily the professional obligations attending the project. Some studies are in herently more complex than others, and the requirements of the problem are not always the same. Some examinations require the detailed investigation of large operating or nonoperating mines or, possibly, of mining districts; others involve more or less reconnaissance studies; and still others rela¬tively small undeveloped mineral occurrences. Likewise, the primary objective of some analyses may be the evaluation of a mineral deposit or a mining property, whereas in other projects the major objective may be guiding mining or drilling work in the discovery of new or hidden ore bodies and mineral-bearing structures. Thus, the possible range of any given examination may extend in varying degree through one, or more, of the following types of procedures: 32.1.1--GEOGRAPHIC ENVIRONMENT Studies of geographic environment should be made to ascertain the general physical situation in the area under consideration and to identify those correlative factors hearing on the, findings resulting from the field examination. This commonly will include determinations of: A. Location of the field area with respect to the state and county in which it occurs and, if feasible, a record of the township, range and section with reference to the principal meridian, and base line (or lines) that apply. For examinations in foreign countries, or in regions outside the continental United States, it is desirable that the field locality, in each instance, be identified with reference to the boundaries of some form of political entity essentially comparable in character to the divisions used in the United States. B. Distances from existing communities and related service centers, via: 1. Roads, both improved and unimproved. 2. Railroads. 3. Navigable waterways. 4. Airports. C. Topographic relief as it will influence the selection of 1. Pit site or positions of underground mine portals or shaft sites, including dump areas. 2. Mill site, including tailings disposal area.

Jan 1, 1973

By Fabiola Espinoza Carmona, Elena Chiriotti, Edoardo Misano

"INTRODUCTION Ganntas Tunnel is part of the modernization project of the railway between Alger and Oran, in Algeria. In order to double and rectify the existing line between El Affroun and Khémis Miliana, the alignment foresees the excavation of a 7 km-long twin tunnel. The excavation works started in June 2011 with the contractor CCECC, under the supervision of SYSTRA. Excavation is driven in conventional method by hydraulic hammer simultaneously on 8 different faces since excavation was started also from a junction window towards the middle of the tunnel. The minimum longitudinal distance to be respected between two contiguous tunnel faces has been set to 30 m. The tunnel cross-section is a 70 m² oval shaped profile, temporary support consists of shotcrete, bolts and steel ribs. A 30 to 50 cm thick cast in situ concrete final lining has been provided as well. When the tunnel reached a fault zone in soft clayey marls extreme squeezing occurred, works were stopped and re-profiling operations were carried out along more than 100 m. To date, works proceed at slow rate since high convergences are still monitored and completion of works is not expected before December 2016.GEOLOGY The project is located within the Tellian Atlas mountain area, including in particular the Djebel Ganntas massif in between Mitidja and Chleff plains. Djebel Ganntas is characterized by an extensive massif aligned in East-West direction with smooth slopes made of soft clays that emerge in multiple cliffs and ravines. On the top of it, along the edge, a more recent sandstone formation is found. The existing data on the geology did not allow to establish an accurate geological model at tender stage. In-situ investigations allowed at design stage to identify a Quaternary alluvial cover of clays and gravel, followed by a Miocene stratum divided in a sandy top layer and a lower clayey layer. From a structural point of view, geological maps suggest a north direction dip of layers, but the in situ surveys showed that layers were highly folded. The lack of information at tender stage on the structure of the geological series should have triggered an extensive investigation campaign at detailed design stage which did not take place causing serious consequences on costs and time at construction stage."

Jan 1, 2016

By R. H. Grau

This Bureau of Mines report describes methane liberation trends from all U.S. coal mines liberating over 100 Mcfd (100,000 cfd) (2.8 Mm3/d). Detailed are results from the latest Bureau survey performed in 1985 and shown are mine and company name, location, coalbed and methane liberation quantity. The report shows that in 1985, there were 180 mines producing more than 100 Mcfd (2.8 Mm3/d) and the total quantity of methane liberated by these mines was 303,900 Mcfd (8,605 Mm3/d). This data is compared with previous studies performed in 1971 , 1973, 1975, and 1980. From 1971 to 1985, there was a 10% decrease in the number of mines liberating at least 100 Mcfd (2.8 Mm3/d) but there was a dramatic 34% increase of liberations from these mines. The increase seems to be caused by new mines being developed in deeper, gassier coalbeds, particularly in Alabama. Likewise, in comparing the ten highest liberating mines in 1975, 1980, and 1985, an increase in methane liberations each year was experienced. The report classifies mines by three levels of liberations: greater than 100 Mcfd but less than 500 Mcfd (2.8 to 14 Mm3/d); 500 Mcfd to 1 ,000 Mcfd (1 4 to 28 Mm3/d); and greater than 1,000 Mcfd (>28 Mm3/d). It was found that 87% of liberations were from mines producing over 1,000 Mcfd but these accounted for only 38% of all the mines in the study.

Jan 1, 1987

By U. Schoepf

Economic and at the same time environmentally acceptable mining of small vertical ore bodies and veins to great depths has always been a challenge for miners. The Bauer cutter system, widely used in civil engineering, has been further developed for applications in exploration and mining, to a sustainable system for selective mining with a focus on small vertical ore bodies and veins, as well as residual ore in open pit operations. Current situation of conventional mining of small ore bodies and vertical veins Small ore bodies and vertical or near-vertical ore veins often pose a challenge to the mining industry. The relatively small size of the ore deposit over great depths or lengths, with only limited exposure to the surface makes economical mining difficult. Open pit mining of such ore bodies must either be terminated early because of the high stripping ratio and the enormous environmental impact or is unprofitable from the very beginning. The required massive stripping of waste rock leads to high material hauling times and costs, intensive roadway and bench construction and maintenance, possible safety hazards due to heavy vehicle movement, pit wall stability risks, intensive surface water management and massive waste dump requirements. In addition, it can be assumed that increasingly extensive rehabilitation measures will be required in the future after mine closure. Particularly in vertically oriented magmatic and hydrothermal deposits the technical, economic and environmental limits for further pushbacks, to extend the open pit depth, can lead to an early end of mine life even if a significant quantity of residual ore is left behind. Going underground is only a viable option in a limited number of mines with very high ore values and volumes. The high development cost of an underground mine, as well as the higher underground mining costs, often prevent further mining to greater depths.

Feb 1, 2023

By Jean-Luc Cornet

Downhill, or regenerative conveyors have always been a challenge to the design engineer due to their natural instability under load. The last decade has seen the appearance of high tonnage, high negative lift conveyors with several hundred meters of drop. These conveyors have made necessary the development of new braking systems and intelligent drive controls to address their starting and stopping requirements under various load conditions. This paper describes the critical design criteria of large regenerative conveyors and some of the advances in mechanical braking systems and drive control technology developed by Conveyor Dynamics, Inc. (CDI) to address their specific requirements.

Jan 1, 1993

By Joseph W. Johnson

General Electric introduced electric drive systems on 85 ton Off-Highway mining trucks in the early sixties. Due to favorable economics, trucks have increased in size to handle larger payloads. Series Motorized Wheel systems were developed to meet this demand. When the technology was available, General Electric switched from use of Series motors to separately excited motors with the added benefits of static exciters and simplified control. Over 20 years of electric drive experience have been incorporated in the STATEX drive systems, which covers truck sizes from 85 to 220 tons. This paper traces the drive system developments from the early stages to the present and takes a look at what's ahead.

Jan 1, 1983

By D. Bogunovic

The objective of this research was to conduct field-scale experiments at an operating surface coal mine in order to determine the impact of the bucket fill factor on dragline production rate and energy consumption. Data collected from a dragline monitoring system were recorded in a specifically designed software tool and the relationship among these parameters was established. an algorithm for the determination of the ?best? fill factor was developed and integrated in the software. It was determined for the analyzed dragline in the mine that energy consumption in the digging phase can be reduced by 36% and production rate can be increased by 1.4% for a bucket fill factor of about 80%, a fill distance of 19.8 m (65 ft) (i.e., 3.1 bucket lengths) and a bucket fill time of 15 sec. the method developed and applied in this study may help dragline operators to determine the fill factor that will increase production rates and reduce energy consumption in specific surface coal mines. Mining Engineering, 2011, Vol. 63, No. 8, pp. 48-53. Official publication of the society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016