Search Documents

By W. M. Husslage

The permeability in the blast furnace shaft is adversely affected by low temperature reduction degradation of sinters. The fundamental cause is an expansion of the iron oxide phase resulting from reduction of hematite to magnetite. The present study showed that expansion behavior during the hematite / magnetite reduction step and the resulting microstructure are strongly influenced by the reduction temperature (viz. partial oxygen pressure), the reducing agent and the nature of the hematite. The reduction rate is of minor importance. A reduction mechanism is proposed, explaining the dilation behavior and the magnetite microstructure. The results can provide better insight into reduction degradation behavior.

Jan 1, 1998

By Matthew Geary, Stephen J. Marino, Jordan A. Schreiner

"INTRODUCTION Project Overview The Southeast Collector (SeC) is a new 15km long 3.0m internal diameter wastewater tunnel designed by Hatch Mott MacDonald (HMM) that twins the existing 2.6m diameter York-Durham Sewage System (YDSS) tunnel. Both sewage tunnels are located north of the City of Toronto in Ontario, Canada. The SeC provides much needed conveyance capacity for the rapidly growing York Region population, supporting development until 2036 and increasing sewage system security (Hatch Mott MacDonald and AECOM 2011). Construction of the SeC will also permit flows of the twinned section of the YDSS to be bypassed in order to clean, inspect and carry out any essential maintenance within the YDSS tunnel. Although owned and operated by York Region, the SeC spans two regional municipalities beginning upstream from the intersection of Ninth Line and Rouge Bank Drive in the City of Markham in York Region to the downstream Finch Avenue and Valley Farm Road intersection in the City of Pickering in Durham Region. See Figure 1 for the SeC and YDSS alignment. The project includes 19 shafts and chambers with depths ranging from 8 to 48m in addition to seven facilities supporting the operation and maintenance of the sewer. The construction contract was awarded to Strabag Inc. in July 2011 for $291M CAD. Construction Management services were provided by a joint venture team of Hatch Mott MacDonald and AECOM. Existing York-Durham Sewage System The YDSS tunnel was completed in 1979 and was constructed using an open shielded TBM with ribs and lagging temporary support, followed by installation of a 380mm thick unreinforced cast-in-place (CIP) concrete final lining. The YDSS sewer system has numerous connections that accumulate flows from various urban areas within York Region. The section of the YDSS twinned by the SeC flows under gravity conditions and had been putting a strain on the municipality’s potential for population and development growth having reached its maximum capacity of 420 ML/d. According to the York Region’s Water and Wastewater Master Plan, the existing YDSS would not have been able to handle wet weather flows past 2016 (Genivar and XCG Consultants 2009). The dependability of this section of the YDSS is also of concern because it is the main and critical connection between the sewer systems upstream and the downstream Duffin Creek Water Pollution Control Plant (WPCP)."

Jan 1, 2016

By P. Moran

A promising and increasingly popular tailings management strategy is to place cemented tailings underground as backfill. The placement of cemented tailings results in enhanced geotechnical stability and a purportedly more geochemically stable tailings form with lower leaching potential. Conventional subaerial tailings management can negatively affect water quality if weathering causes acid rock drainage and metal leaching (ARD/ML) to occur, whereas cemented tailings can limit leaching via porosity and permeability reductions and contribute alkalinity to limit the potential for ARD/ML. Cemented tailings backfill appears to be better, but how can this advantage be proven? Currently, cemented tailings backfill is utilized at mining operations internationally, but there is limited guidance on performing geochemical characterization and associated evaluation of the potential impacts to water quality. As a result, various approaches to simulating the leaching behavior of cemented backfill have been utilized, including some methods that are unlikely to represent weathering under site-relevant conditions. American Society for Testing and Materials (ASTM) Standard Test Method C1308-08 is a diffusion testing method initially developed to assess constituent release rates from solid nuclear waste forms. ASTM C1308-08 uses intact cylinders that more closely represent actual backfill than methods that require crushing or size reduction. It is widely believed that leaching from actual cemented tailings is controlled by diffusion through small pores that exhibit limited exposed surface area, making diffusion testing particularly applicable to cemented tailings placement.

Feb 27, 2013

By Andrew Burton, Damian Schofield, Jeremy Noond

This paper will introduce and discuss a range of techniques that utilise new developments in Computer Graphics (CG) and Virtual Reality (VR) for the investigation of incidents and accidents in mining environments. The future of mining safety may not be totally led by the demands of the mine operators, but sometimes by the academics, commercial software developers and legal pioneers who generate new ideas and products and set admissibility precedents which may change the way certain traditional investigative operations are performed. In any accident investigation the outcome from the investigating team is often a complex affair and the results of the investigation are often reported in large, convoluted documents. Computer-generated forensic reconstructions allow investigators to present accident scenarios in an accessible and easily understood, visual manner. Surveys in the US have also shown that people have increased recall of computer-generated images over many other forms of evidence. The AIMS Research Unit in the UK have been pioneering the use of Computer Graphics (CG) and Virtual Reality (VR) technology for both industrial and road traffic accident reconstruction. This paper and accompanying presentation will contain examples of forensic reconstructions developed by the authors that explain some of the methodologies used to ensure admissibility of this type of digital evidence. The paper will contain a number of case studies based on UK and International industrial accidents. The paper will focus on how AIMS Research is extending the capabilities of the accident reconstructions created to take advantage of the latest developments in VR technology. As digital technology makes its impact within professional and commercial fields, computer generated forensic reconstructions will form important admissible evidence in the courtrooms of the future. The technology will also make a great impact in the way we train our workforces, with highly visual three-dimensional (3D) interactive training tools becoming the norm. Acceptance by the public, courts and workforce is an important issue, and implementation strategies must be considered carefully.

Jan 1, 2002

By Sidney A. Suhler

The persistent requirement for methods and equipment capable of detecting hazardous anomalies in advance of underground mining has led to the development by the U.S. Bureau of Mines of a directional radar probe. The probe operates from boreholes drilled from the surface into the underground region to be mined. The engineering model radar was completed in early 1982 and field demonstration tests were performed in May of that year at a selected coal mine. Preliminary in-situ electromagnetic tests were performed at several candidate coal mines to evaluate the radio-frequency characteristics of the coal. A coal mine in New Mexico was selected on the basis of low EM propagation losses in the coal and the presence of an extensive coal seam displacing fault as a radar target. The borehole radar was operated in two vertical boreholes which intersected the coal seam at approximately 25 and 40 feet from the fault interface. Radar reflections from the coal/ rock interface were detected in both tests. Underground tests in a horizontal borehole in the coal were less successful because of interfering reflections. Additional borehole-to-borehole tests were performed with a separate ground penetrating electromagnetic system to obtain radar range calibration data. The coal was found to be bounded by very lossy roof and floor sandstone and shale while propagation through the coal seam was obtained at distances up to 175 feet between test boreholes. Coal seam continuity was indicated by the hole-to-hole experiments through a section of the seam previously thought to be completely cut off by the fault.

Jan 1, 1983

By Z. Jin, D. DePaoli, P. Zhang

"Phosphorite, or phosphate rock, is the most significant secondary rare-earth resource. It contains high amounts of phosphate-bearing minerals along with low contents of rare earth elements (REEs). In Florida, about 19 Mt of phosphate rock are mined annually and most are used to manufacture fertilizers using a wet process, in which sulfuric acid reacts with phosphates to produce phosphoric acid and phosphogypsum. In the wet process, REEs are also leached out into solution and eventually get lost in the leaching residue and phosphate fertilizer. Recovering REEs from Florida phosphate rock in the wet process will be beneficial to broadening rare-earth availability, improving the quality of phosphoric acid product and protecting the environment.This study focuses on the influences of wet-process operating conditions on REE leaching efficiency. The results indicate that REE leaching efficiency increases with phosphoric acid addition in the initial pulp. At a temperature of 75 °C, a stoichiometric ratio of sulfuric acid (H2 SO4 ) to calcium oxide (CaO) of 1.05 and a weight ratio of liquid to solid of 3.5, REE leaching efficiency reached a relatively high value of 52.82 percent. The trends of REE leaching efficiency were similar to those for phosphoric acid (P2O5 ). Extensive tests on the leaching residue showed that during leaching, about 90 percent of the REEs were released from the phosphate rock but only 52.82 percent ended up in the leaching solution. This phenomenon can be attributed to two factors: (1) the effect of phosphate ions (PO4 3-) in the solution, which caused REE ions to form REE phosphates and be precipitated into the leaching residue, and (2) the influence of large amounts of anions such as sulfate (SO4 2-), dihydrogen phosphate (H2 PO4 -) and hydrogen phosphate (HPO4 2-) anions as well as the polar molecule H3 PO4 , which surrounded the REE cations and formed an ion atmosphere that prevented the PO4 3- from contacting and combining with REE cations. Interaction of these two opposite effects determined the REE distribution between leaching solution and residue."

Jan 1, 2017

By D. J. Miller

Environmental considerations are extremely important in planning and carrying out mergers, acquisitions and real estate transfers. It is not inconceivable that potential or actual environmental liabilities could exceed the targeted company's net worth or the book value of the real estate of interest. It is therefore essential that an environmental due diligence investigation (DDI) be performed to quantify environmental liabilities before sales, mergers or acquisitions. This paper will discuss general procedures used in environmental due diligence investigations. The emphasis will be placed on mergers and acquisitions. It should be pointed out that the procedures discussed in this paper are general and must be modified to fit each particular merger or acquisition under consideration.

Jan 1, 1988

By Jr. Foot

EIMCO Process Equipment Company has introduced the new SmartCell series of conventional flotation cells. The flagship of this new development is the 5000 ft3 cell that is the largest available in industry. This new series of cells includes a cylindrical tank design, a conical draft tube and froth crowder. Optional air control, wash water addition and embedded expert control are available. A discussion of the design parameters, energy efficiency, testing, and commercial plant results are presented.

Jan 1, 1997

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By Xinghai Lei, Nan Wang, Xiangyang Jin, Yuqi Ren, Yang Li

The upward mining method, as an effective mining method, is widely employed in close-multiple coal seams to extend the service life of coal mines and improve the recovery rate of residual coal resources. However, the upward mining feasibility of the upper coal seam is related to the height of caved zone of interlayer strata after lower coal seam extraction. Therefore, it is extremely important to determine the height of the caved zone after the lower coal seam. The No. 9 coal seam (upper coal seam) and the No. 12- 1 coal seam (lower coal seam) in the Qianjiaying coal mine are selected as the research object. The characteristics of the interlayer strata structure field, fracture field, and subsidence field are studied using UDEC numerical modeling, in which the height of the caved zone is gotten after the No. 12- 1 coal seam extraction. Furthermore, the height of the caved zone is verified by onsite detection of GPR and BTVI. In the numerical modeling, the height of the caved zone is 19.6 m. And the height of caved zone is 14.7 m and 15.4–21.2 m, respectively, by using the onsite detection of GPR and BTVI. The heights of the caved zone onsite detection results are consistent with the numerical modeling result. The No. 9 coal seam is always located above the caved zone after the No. 12- 1 coal seam extraction. Consequently, the upward mining of the No. 9 coal seam is feasible.

Jun 28, 2023

By J. Jorge, J. Mariño-Salguero, B. Álvarez-Rodriguez, J. M. Menéndez-Aguado, J. J. de Felipe

"This work focuses on the characterization of heat generation during dry fracture by direct impact of a tantalum ore. Moreover, an attempt was made to quantify the heat energy loss to the environment during the grinding process of a ball mill. The study was carried out using mineral samples from a Spanish mine that were characterized by measuring their density and specific heat. During the experiments, increases of temperature ranging from 5.9 to 7.3 °C after the fracturing process were observed. A numerical model was then applied to calculate temperature distributions through the mill wall. Three possible combinations of heat transfer coefficients were analyzed, from (1) Kapakyulu and Moys, (2) Duda and (3) the heat transfer laboratory of Universitat Politècnica de Catalunya. The models with the coefficients from Kapakyulu and Moys and the heat transfer laboratory of Universitat Politècnica de Catalunya were found to provide results that were in best agreement with the experimental data. IntroductionEvery year, several billion tons of metallic ores, minerals, cement and other solids used in the ceramic and chemical industries are subjected to size reduction in ball mills around the world. The U.S. Department of Energy (2005) reported that in the United States about 29 percent of the total energy used by the mining industry, or 0.4 percent of total U.S. energy consumption, is used in comminution. In Canada and Australia, comminution is responsible for about 2 percent and 1.5 percent of total energy use, respectively. In nonindustrialized countries where mining constitutes higher fractions of their industrial sectors, comminution costs represent a significant contribution to mine operating costs. The specific energy consumption values for the grinding of these materials typically range from 5 to 50 kWh/t. Thus, a significant amount of electrical energy is consumed in the ball mill grinding operation (Aguado et al., 2006; Gupta and Sharma, 2014). Grinding can represent up to 50 percent of the direct operating cost in a mineral processing plant, especially as comminution devices operate in highly inefficient ranges of 4 to 8 percent (Wang, Yang and Yu, 2012)."

Jan 1, 2017

By Steven K. Ruggieri

Increased coal production on longwalls has brought with it higher levels of dust generation. Most U.S. longwall mining operators have difficulty complying with Federal dust standards, which are stricter than European standards. Longwall operators faced with a longwall that is "out of compliance" have implemented a variety of practices designed to reduce dust levels. Mining conditions and other important variables, however, can cause fluctuations in dust levels that may overshadow the performance of a new dust control technique. This can result in the continued use of an ineffective technique or lead to the abandonment of an effective dust control technique. No single technique can keep a longwall in compliance. Maintaining compliance requires a fundamental approach to dust control -- proper application and continued use of effective dust control techniques.

Jan 1, 1983

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

By Nord L. Gale

The discovery of important new ore deposits of lead, zinc, copper and silver in 1955 in Southeastern Missouri has resulted in the development of a thriving mineral industry known as the "New Lead Belt" or "Viburnum Trend", to distinguish it from the older lead producing areas to the East. This region has recently become the world's largest lead producing district with production in 1970 reaching 432,576 tons or 74.4% of the entire United States lead mine production. The area is heavily forested with rolling hills dotted with numerous clear running streams in the Clark National Forest of the Missouri Ozarks. The location is within 70 miles of St. Louis, Missouri and has a natural abundance of water resources which provide an important recreational area for fishing, hunting, camping and other outdoor activities. Until this recent development, the area was sparsely populated and industrialization was almost unknown. The infusion of $150 million in mining capital has brought about a dramatic change in the economic structure of the area and will almost surely be accompanied by changes in its environmental picture. In an effort to maintain this bountiful national resource and to evaluate the changes occurring in surface water quality and aquatic life forms present, an inter- disciplinary research program at the University of Missouri has been undertaken with the support of the National Science Foundation. Research has been carried out to determine background values, establish natural baselines, and to evaluate the extent and causes of changes in streams effected by mine water discharges and wastewater from ore milling operations. The unique topography of the "New Lead Belt" area allows the channelization of milling and smelter wastes to separate stream systems (Figure No. 1) thus allowing measurements of the pollutional effects on an individual basis.

Jan 1, 1973

By S. A. Anzalone

The Helvetia copper deposit is a large undeveloped Laramide porphyry copper system located in the Santa Rita Mountains, Pima County, Arizona. This porphyry copper system consists of four areas of copper mineralization: Rosemont, Peach-Elgin, Broadtop Butte, and Copper World. Asarco refers to the four areas collectively as the "Helvetia Deposit". Mineralization and alteration are primarily contact pyrometasomatic, and zoning of hydrothermal alteration and sulfide mineral assemblages are similar to those observed at the Twin Buttes and Mission copper mines located approximately 32 km west of Helvetia. Asarco acquired the Helvetia Deposit in 1988 and has continued the exploration and development effort since then. A considerable amount of excellent geological work has been completed in the area but little information has been published on developments since the mid-1950's. The geology of the deposit as developed by numerous geologists over the past 75 years and the large, bulk tonnage low grade copper deposits outlined in recent years will be briefly reviewed in this paper.

Jan 1, 1992

By D. W. Park

A vast majority of longwall operations in the United States use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite element model of the shield structure was made to study responses of each long wall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested to develop a technique incorporating the finite-element method to evaluate the real-time shield performance for the purpose of effective ground control.

Jan 1, 1992

By W. C. Brice

Minnesota's mineral resources are widespread and diverse (Figure 1). In addition to the nation's largest iron and manganese reserves, the state contains sizeable vanadium, copper, and nickel resources. Recently it has been determined that the proterozoic unconformities in Minnesota have a favorable potential for uranium deposits. Finally, major potential exists in Minnesota's archean greenstone belts for gold, silver, and copper-zinc massive sulfides. Many of the state's mineral resources have been found in environmentally sensitive areas. This is not surprising since the natural forces associated with the formation of mineral deposits are often the same processes that create unusual landforms. For example, much of the state's copper-nickel is found within and adjoining the Boundary Waters Canoe Area (BWCA) and Lake Superior. The history of mineral development on the Mesabi Iron Range has also created culturally sensitive areas. Early iron mining development required the workers to live close to their jobs, and mine wastes were dumped as near the mine as possible. Few, if any, foresaw the time when taconite would be economic to mine. Therefore, it is not unusual to find valuable taconite resources located under towns and waste dumps on the Mesabi Iron Range.

Jan 1, 1980

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By A. Bascetin

Materials produced in quarries have been used for different intentions such as concrete and cement raw material, asphalt and embankment aggregates, railway ballast. Especially in cement manufacturing, the chemical composition and the uniformity of the raw materials play a strategic role in the economy and quality of the cement process. Therefore, it is necessary to achieve uniformity and desired chemical composition and maintain these at all production stages according to the type of cement produced. To achieve this goal the production planning and pit design play an essential role. This paper briefly outlines the production optimization of cement raw materials in a quarry in Istanbul western part of Turkey. For the purpose it was used the 3D ore body modeling and the geostatistical techniques. The variation of chemical components (%CaO, %Al2O3, %Fe2O3 etc.) and quality control parametres (LSF, SR, AR and etc.) obtained from the quarry were determined. Then the values of unknown chemical components and quality control parameters in the ore body were estimated using Kriging which is one of the geostatistical interpolation methods. The open pit design was also created by specifying wall slopes and taking into consideration of the grade distributions of the benches. The most important revolution in the paper is investigating the effects of the block dimensions in block modelling which is important for reserve estimation. The other important point in the study is using the different range values in variogram analysis for determination optimal reserve estimation. n this study, the effects of two parametres on reserve and waste amount estimation were determined according to CaO% distribution. The study was pointed out that the changing of the two parameters are very important for the optimal mine planning and environmental considerations.

Jan 1, 2010

By K. Burke, K. L. Myers, R. Espell

Barrick's Goldstrike AA heap leach pad is an HDPE-lined facility that was used for gold recovery from low-grade ores using conventional cyanide heap-leach technology. The pad was operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA leach pad facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada's closure requirements. The traditional Nevada leach pad closure procedure involves rinsing to reduce the cyanide concentration to an acceptable level followed by reclamation. However, rinsing does not typically reduce certain metals and compounds, and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as in Nevada, the fine-grained layer will rarely reach saturation, and the cover will be able to store water during precipitation events and will allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22-m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the recontoured AA heap leach pad was specifically designed to enhance the re vegetation, reclamation and sediment yield control aspects of the AA heap leach pad closure, while resulting in a natural looking surface that is compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for recontouring and erosion-control design.

Jan 1, 2002