Search Documents

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By W. B. Lambert

A common decision in openpit mining is to determine the extraction sequence of notional three-dimensional production blocks so as to maximize the net present value of the extracted orebody, while adhering to precedence and operational resource constraints. This openpit block sequencing (OPBS) problem is commonly formulated as an integer program, with binary variables representing if and when each block is extracted. In practical applications, the number of blocks can be large and the time horizon can be long; therefore, instances of this problem can be difficult to solve using the exact approach of optimization. The problem is even more challenging to solve when it includes explicit minimum operational resource constraints. Our maximum value feasible pit (MVFP) algorithm generates an initial integer feasible solution for OPBS problems, in which minimum operational resource constraints are strictly enforced. As an exact approach, we present a Tailored Lagrangian Relaxation (TLR), in which the selection of constraints to dualize is guided by information provided by the MVFP algorithm. We present results and graphics to demonstrate the utility of our techniques for instances containing up to 25,000 blocks and 10 time periods.

Jan 1, 2013

By A. K. Clarke

In any treatment process that requires a coarse feed material to be reduced to a fine size by crushing and/or grinding it must be determined whether a wet or dry comminution system should be utilized. All factors must be evaluated in reaching the decision. Among these factors are: 1) Ecology and Plant Environment: Unfortunately in many instances the decision on wet or dry is based on prejudice resulting from an unnecessary fear of dust. The writers submit that this fear, although once justified, is no longer valid because technology and equipment is now available to collect dust to meet any standard. When dry grinding is used it is very often possible to discard a portion of the waste product in a dry state. This will decrease the size of the tailing pond required. As pollution control standards increase it becomes increasingly difficult to clean up water from tailing ponds. 2) Operating Costs: Steel wear is often five or more times greater in wet grinding than in dry grinding. This is mainly due to corrosion. The evaluation of the economics of dry grinding must of course include the air system and dust collection; similarly in a wet grinding plant related pumping and material handling costs should be included. Pumping costs are often overlooked. This assumes water is made to flow for nothing. Pumping can account for 20 percent of the power consumption in the grinding plant. Large scale comparative tests were conducted in a wet and dry commercial plant in 1970. The same ore was used for both tests. With all factors included in both plants the dry system showed lower horsepower per ton.

Jan 1, 1971

By Yuanbo Zhang, Yikang Tu, Zijian Su

Stainless steel swarf is a typical by-product produced from stainless steel processing, which contains a significant level of valuable metals, such as iron, chrome, and nickel. About 1 million tons of stainless steel swarf are generated in China annually, but as mixed with impurities such as Al and Si, stainless steel swarf is not suitable to be directly smelted into stainless steel through refining process. In this study, stainless steel swarf was applied as a strengthening agent during limonitic laterite sintering process. The effects of adding stainless steel swarf on green bed permeability, the yield and quality indexes of the sinters, and the microstructure of the sinters were evaluated systematically. The results showed that the concentrated distribution degree of granules and green bed permeability were improved after adding stainless steel swarf. As the additional amount of stainless steel swarf increased from 0 to 3%, the tumble index and yield of the sinters rose from 50.07 to 54.69% and from 62.04 to 67.35%, respectively. The addition of stainless steel swarf would not change the phase compositions, and had little adverse impact on the metallurgical properties of the limonitic laterite sinters.

Aug 23, 2023

By James E. McNulty

The planning and development of new coal mines is requiring the increased use of geologic, geologic engineering and hydrogeologic investigations. This is caused in part by the fact that new mines must deal with less favorable conditions than existing mines as well as higher costs of development and in part by the dictates of regulatory authority. High costs of new mines require greater reliability of geologic assessment using best available geotechnical and geophysical methods and technology. Although the increased cost of additional subsurface data is significant, the more important factor may be the impact on project lead time.

Jan 1, 1981

By Zoltan F. Oszter

The frictional resistance to motion of a belt conveyor has always been a subject of intensive studies and research by engineers throughout the years. Numerous informations have been developed by analysing series of field tests on belt conveyors of different characteristics and carrying different materials at various capacities. Within certain limits of weight per unit length and tension, the theoretical considerations and the analysis of the field tests, both in the US and abroad, resulted in the development of similar formulas. In general these formulas are safe to use up to the following limits:

Jan 1, 1977

By L. Thompsen

High-pressure grinding rolls (HPGR) offer capacity increases, savings in operating costs and metallurgical advantages. The first installation of the Polycom HPGR in a copper ore treatment plant occurred in July 1995 at Cyprus Sierrita’s mining complex near Green Valley, AZ (Fig. 1). Until that time, the benefits this technology offers for copper and gold ore were only demonstrated on testwork. In other industries, such as diamonds, HPGR have proven to be reliable in industrial-scale plants and have set a new standard for this kind of ore treatment plant. HPGR are also successfully used for the comminution of coal, blast furnace slag and in cement and pelletizing plants. The installation at the Cyprus Sierrita Mine should prove the economical benefits in commerical-scale copper mining, confirming the results of comprehensive testwork(Fig. 2).

Jan 1, 1996

By Fan Yang, Zhiping Wen, Tiancheng Nie, Jinhe Pan, Ruibo Jia, Changchun Zhou

Rare earth elements have important strategic significance and economic value, and the rare earth elements in coal resources have considerable development potential. This study took coal refuse in the Jungar area of Inner Mongolia, China, as the research object, and investigated the occurrence modes of rare earth elements. A special sequential chemical extraction experiment was designed, and the results showed that the rare earth elements in coal refuse mainly occur in silicate and aluminosilicate form, accounting for approximately 65% of the total rare earth elements. According to the results of SEM-EDS, micro morphology of the sample belonged to the lamellar structure of clay minerals, and Al, Si, Fe, S, Y, and La were all present in the sample. Through SPSS software analysis, rare earth elements have an obvious linear positive correlation with Al, Si, and Fe elements, and a negative correlation with S elements. The rare-earth element occurrence mode in coal refuse can provide a definite theoretical basis for the later extraction and enrichment work.

Feb 18, 2022

By Raymond A. Povirk, David L. Bartsch, James V. Hamel

The Ohio Valley Coal Company is expand- ing its Powhatan Mine No. 6 near Alledonia, Ohio. This expansion includes a 20 rn (65 ft) height in crease for an existing 44 rn (145 ft) coal refuse - slurry impoundment dam. The dam is being raised by upstream construction which will involve placement of more than 15 m (50 ft) of new fill over an existing reinforced concrete decant structure. This structure is 0.76 rn (30 in.) square inside and its deepest portion was under 24 m (80 ft) of coal slurry and water. The top of the decant structure was not strong enough to safely support the new fill and, because of the slurry and water, there was no way to reinforce the structure from the outside. The structure was reinforced frorn the inside by sliplining 73 m (240 ft) of 0.66 rn (26 in.) OD, 0.53 rn (21 in.) ID polyethylene pipe, grouting around this pipe with cellular concrete. and constructing a steel-fiber reinforced micro-silica concrete transition at the upslope end of the pipe. Rehabilition of the decant structure was completed in August 1989. The rehabilitated decant structure is now performing satisfactorily as fill is being placed over it for raising the dam.

Jan 1, 1991

By Ranajit Kumar Sahoo, Shatrughan Soren, Surendra Kumar Biswal, Soumya Sahoo, Sachida Nanda Sahu

The presence of appreciable quantity of clay mineral in Indian hematite ore needs an attrition technique using screw scrubber in the beneficiation circuit to remove the ultrafine clays and avoid downstream operational problems. Spectroscopic analysis revealed that iron ore samples obtained from the Barbil region of Odisha contain a high amount of silica and alumina in the form of clay minerals (e.g., kaolinite) contributed as a loss on ignition (LOI) in the iron-making process. Iron ore fines of below 10 mm size were subjected to a laboratory-scale screw scrubber, and the effectiveness of scrubbing as well as the pelletization of the scrubbed product was investigated. The screw scrubber in the beneficiation circuit helps to remove the clay minerals, causes an increase in iron values from 63.65% Fe(T) to 66.18%Fe(T), with improved physical (CCS of 325 kg/pellet) and metallurgical (RDI of 2.24%) pellet properties.

Aug 31, 2020

By Megan Badonie, Devlon Shaver, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Critical minerals are becoming more important in our technological society because they are used in many of our electronic devices, batteries, and magnets. In New Mexico, low to moderate concentrations of critical minerals are found in Late Cretaceous coal and related strata in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, REE, and Critical Minerals) program. The New Mexico coal, humate, and clinker deposits are relatively low in REE (<325 ppm TREE), Li (<90 ppm), V (<168 ppm), Co (<51 ppm), Ni (<108 ppm), Zr (<557 ppm), and many other critical minerals compared to normal economic deposits. Some of these rocks are enriched in Al2O3 (<40%) and Sr (<3740 ppm), both critical minerals. Common minerals hosting the critical minerals in these rocks include clay minerals, zircon, and rutile/anatase. As the demand for some of these elements increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Ultimately, economic potential will most likely depend upon production of more than one commodity, maybe even from coal, humate, and clinker deposits.

Feb 1, 2024

By Myles E. Robinson

Significant changes in the markets for coal have taken place since World War II, As used in this study the term ?coal? will refer to bituminous coal, The anthracite industry in size, characteristics, and problems differs materially from the bituminous coal industry, These changes have both influenced and been influenced by the mechanization of mines, and by decreased distribution costs, especially in transportation. It is the purpose of this paper to examine these post-war changes, to assess their impact upon the production and distribution of coal, and to explore future market developments in the light of past and present trends and relationships. The layman lacks adequate informatian on the production, demand, and distribution of coal. There are two reasons for this. First, there is a relative lack of statistics coveting the industry, Coal operators and distributors are not required to file with any government agency the type of much more complete statistics filed by the railroads and public utilities with national and State agencies. The Bureau of Mines assembles much useful information on the coal industry, but several areas, including that of investment and finance, have no central depository which can be used to keep the public informed of the nature and extent of the industry and its problems.

Jan 1, 1964

By F. C. Appleyard

As one of the more important Industrials Minerals, gypsum occupies a significant place in the economy of the United States, particularly in that segment which can be loosely called the Construction Industry. For many years, products made from gypsum have been a major building material, and the usefulness and versatility of these products is such that their widespread use is expected to continue. In 1968, according to U.S. Bureau of Mines statistics, the value of all gypsum products sold in the United States was 405,000,000 - and although this value has dipped from the 1964 high of $ 432,000,000, it is expected to trend upward in the next few years to equal and surpass this figure as the construction industry recovers from its current squeeze of "tight money" and high interest rates. There are many factors to be measured in determining the potential value of any mineral deposit, and how it might fit within its particular industry. What, then, are the qualities which a gypsum deposit must have in order to profitably participate in the four hundred million dollar plus business which is the gypsum industry? First let&apos;s consider the geology of gypsum, the geographic distribution of deposits, and the more important factors such as size, grade, capital requirements, and operating cost. Then, an understanding of the uses of gypsum, various types of products, and location of markets would be helpful, along with such other factors as the structure of the industry, price trends, etc.

Jan 1, 1970

By O. B. Bucklen

The Coal Research Bureau of the School of Mines at West Virginia University, using a modified design of a Russian flotation device, was able to obtain a clean coal product containing 7.64 percent ash with 94 percent yield and 97 percent coal recovery. This favorable performance was obtained with the semi-pilot scale flotation cell operating as a simulated three stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient "operation on high density feed slurry, and absence of moving parts.

Jan 1, 1964

By Ilmar J. Martens

The statistical information and cost data used in this report has been made available by NICKDATA INC. Since 1982, NICKDATA INC. of Toronto, Canada, has produced an annual comprehensive nickel industry cost study. Up to date information on 22 mines, 21 smelters, and 16 nickel refineries representing 30 nickel production operations in 17 countries are included in the computerized cost analysis. The report is compiled from information obtained through regular annual visits to major nickel operations and continuous monitoring of information on all nickel producers. The 1984 report which was completed this summer, reveals drastic changes in the nickel industry cost structures.

Jan 1, 1984

By K. Lapakko

One responsibility of the Minnesota Department of Natural Resources is to encourage the development of mineral resources within the state. A second responsibility is to ensure that mineral development does not adversely impact other natural resources, including the water resources of the state. One approach the Division of Minerals has taken to fulfill these responsibilities is to conduct cooperative research with the mining industry. To encourage mineral development the Division has cooperated with industry on projects related to exploration, mining, and mineral processing. To examine environmental issues the Division has worked in concert with iron ore, base metal, and precious metal exploration and mining companies, as well as the Western Governors&apos; Association, US Bureau of Mines, US Bureau of Land Management, and the US EPA for the past 20 years. These projects were conducted to evaluate methods of predicting, preventing, controlling, and treating problematic mine waste drainages, as well as mine waste revegetation. This paper I) briefly summarizes cooperative projects conducted, 2) enumerates elements which have contributed to the success of cooperative projects, and 3) describes changes implemented for future projects at the Division&apos;s new field and laboratory research facilities, as well as at existing mine and plant sites.

Jan 1, 1998

By Peter Riba

Up until ten years ago the industry had arrived at a relatively conventional, and consistent design of coke ovens. Through the years the designers and builders were not being heavily taxed to come up with revolutionary new designs. However, the stimulus for design change was ever present. These stimuli for change are quite important and they are the driving force which produce improvements. The most obvious stimulus to change a design is commercial. To "build a better mouse trap and the world will beat a path to your door" is the well used cliche which best befits this philosophy. As in all businesses, coke oven designs require that all of the considerations, which affect the cost or the desirability of the design, be optimized. One way to increase the desirability of the particular design, 1s to make the design in- expensive to operate. Or, put another way, to increase production for the same operating cost

Jan 1, 1980

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020