Search Documents

By Gordon Miner

GENERAL DESCRIPTION At the Star mine, Hecla Mining Co., located in Burke, Shoshone County, ID, the mining method is horizontal slicing (timbered or untimbered) cut-and-fill using hydraulic sand backfill. Back stoping as well as breast stoping is used; see Fig. 1. The annual produc¬tion from all cut-and-fill mining is 259 816 t (286,400 st). The average depth ranges from 366 to 2408 m (1200 to 7900 ft). A majority of the tonnage comes from an average depth of 2240 m (7350 ft). Average travel time to the stope is 1 hr. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size and Ground Conditions The ore body is 610 to 1219 m (2000 to 4000 ft) along the strike and 2408 m (7900 ft) on the dip, with an average vein width of 2.6 m (8.5 ft). The dip is essentially vertical. The ore body is heavily sheared and broken on the main fault structures; it is more competent on the wall veins but everywhere subject to rock bursting at depth. The hanging and footwalls are strongly fractured on the main fault structures, again more competent but still fractured on the wall veins. All host rock is Revett quartzite. Value and Production Requirements The ore value is $56 per ton. Production require¬ments are 1089 t/ d (1200 stpd), five days per week. Why Cut-and-Fill? The slusher extraction method is the most satisfac¬tory and practical for narrow vertical veins with sheared walls. The method must be quite selective to be com¬mercial. The veins are too narrow for rubber-tired ex¬traction and the grade is not high enough to make resuing practical. DETAILED DESCRIPTION Development Access to the main shaft is by the 3.2-km (2-mile) main haulage tunnel. The level intervals in the vertical timbered shafts are 61 m (200 ft). Vein development is by crosscut and laterals located 30.5 m (100 ft) into the vein wall. Vein crosscuts are on ±61 m (200 ft) centers. Access to the vein is by raises carried up with the stope. The raises are equipped with four wood¬cribbed chutes (two orepasses reinforced with angle irons, one manway, and one timber slide, Figs. 2-6). The initial cut is located 6.7 m (22 ft) above the main level (Fig. 1). Stoping Cycle Detail Sampling: Grab samples are taken from the mine cars. Channel sampling of the faces and backs is done when necessary. Drilling: For stope drilling, Ingersoll-Rand 300M percussion drills are used, with Ingersoll-Rand 300M and Gardner-Denver RB83M stopers, used for back stoping. Breasting down is done with Gardner-Denver S83FM jacklegs. The back stoping rounds are 0.9 to 1.8 m (3 to 6 ft) and the breast stoping rounds 1.5 to 3m (5 to 10 ft). Blasting: For stope blasting DuPont Tovex 100 watergel with fuses and igniter cord is used primarily. Approximately 60% of the blasting is done with am¬monium nitrate-fuel oil (ANFO). For development headings and shaft sinking, DuPont Drivex watergel with Ensign Bickford Nonel Primadet primers is is used. Mucking: Broken ore is removed entirely by slusher in the stopes. These are mostly 3.7-7.5-kW (5-10-hp) Ingersoll-Rand air-powered or 7.5-37.3-kW (10-50-hp) Ingersoll-Rand electric-powered. In the horizontal de¬velopment headings Eimco 12B and 21 and Atlas Copco LM-56 overshot mucking machines and a 0.76 (1 cu yd) hydroelectric Wagner HST-1 LHD (load-haul-dump) unit are used. Rockway for Extraction: The cribbed chutes (Fig. 7) are nearly vertical and hexagonal in shape and are made of spaced 152 x 203-mm (6 x 8-in.) timber, reinforced with varying weights and sizes of angle iron, depending on wear requirements. Rectangular cribbed chutes are used where ground pressure is not a problem. Cribbing is added in 2.4 or 3-m (8 or 10-ft) extensions accord¬ing to the floor height (whether timbered or untimbered). See Figs. 8 and 9. Backfilling: Backfilling is done with hydraulic sand consisting of classified mill tailings at 65% solids. The fill contains approximately 20% 325-mesh fines. The tailings are pumped 3353 m (11,000 ft) at 50-55% solids 22.7 dry t/h (25 dry stph) with a duplex piston pump. Cycloning increases the tailings density to 65% solids. Fill storage is in a 998-dry-t (1100 dry st) agi

Jan 1, 1982

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By F. Dehghani, B. Rezaie, T. Ghosh, A. Sachan

Comminution is an integral part of the mineral extraction process. However, the influence of the comminution method (ball and rod mills) on silica and magnetite particle shapes has not been substantially investigated. Shape parameters for fractions of -250+212, -150+125, and -106+75 μm sizes were examined utilizing a scanning electron microscope and a Clemex vision PE image analysis system. The silica particles displayed higher elongation and flatness parameter values for rod mill products, but roundness and relative width parameter values of rod mill products are less than that of the ball mill products. Magnetite particle elongation and flatness parameter values of ball mill products in fraction sizes of -250+212 and -106+75 μm are larger than rod mill products, but roundness and relative width parameter values of ball mill products are smaller than rod-mill products, but for the -150+125 μm size range the result is converse. Furthermore, particle elongation and flatness increased with decreasing particle sizes of silica, whereas, roundness and relative width decreased for both Ball and Rod Mills. In case of magnetite, ball mill products displayed an increase of flatness and particle elongations with decreasing particle sizes but flatness increased and roundness and relative width decreased. Similarly for rod mills, magnetite fractions of -150+125 μm were found to have the largest values of elongation and flatness. INTRODUCTION Comminution alters the size and shape, causes lattice distortion, changes chemical composition, surface area, surface-free energy, and polymorphic transformation of all materials. The quantity and quality of such changes depend on specifications of the material feedstock, the type of mill being utilized, the specific energy input, ambient temperature, and environmental pressure [1]. The shape difference between the milled products depends on different grinding mechanisms and the respective breakage principles that these mechanisms depend on [2, 3]. With decreasing particle sizes, the nature of the particle surface become crucial [1]. The influence of the breakage technique has been found to be non-trivial and heavily dependent on the type of grinding mill used for particle size reduction [4]. Shape is an important industrial parameter for predicting particle behavior in downstream processes. The shape parameter affects the way particles burn, compact, are recovered, flow in fluids, sinter, float, agglomerate, fluidize, interact with pulmonary tissue, cut, abrade, react with chemicals, form structural materials, and retain and permit fluids to flow [5, 6]. The distribution of particle sizes and shapes are important for mining, civil and chemical, pharmaceutical, and various other industries with interest in the population modeling of atmospheric dusts, smoke, and grit [1, 3, 6]. The shape parameter not only affects the chemical, physical, surface properties of particles but is also important for downstream processes [5, 6]. Image analysis has been found to provide detailed information about size and shape of the particles and can be used for the control of product quality [4].

Jan 1, 2019

By J. J. Fallon

The subject is "Mergers, Acquisitions and Divestitures in Industrial Minerals, but my remarks could also be applied to new product development, resource development and other new business development activities. At the kernel of the subject is due diligence in major decision-making, that is, where major money amounts and a large corporate commitment are at stake. The "due diligence" means how carefully we do our homework before making the decision. The homework or feasibility study addresses different parts of the decision. In the industrial minerals business the study seeks to uncover the pros and cons in: o The mineral reserves, quantity, quality, mineability, access, etc. o The environmental impact of mining, processing and transporting. o The economics of operations. o Financial aspects o Legal aspects o Many other aspects o And -oh yes! the marketing aspects.

Jan 1, 1990

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products, The original source of potassium was wood ash (hence the name potash), However, today the term potash refers to all commercially important salts of potassium. Sylvite, usually found associated with halite, is the predominant economic potash mineral; carnallite a lesser important source of potassium chloride, while langbeinite is important as a source of potassium sulphate. The world's first potash mining operation commenced in Strassfurt, Germany about 1860, Since that time the industry has grown steadily to its present annual volume of about 30, 000, 000 tons of potassium chloride products or 18, 000, 000 tons of K2O equivalent, potassium chloride or "muriate of potash" being equivalent to 63. 1% pure K2O, WORLD POTASH RESERVES ARE NOT EVENLY DISTRIBUTED The earth's crust contains 2 to 3 per cent potassium, mostly in the form of insoluble silicate minerals. The economically important deposits, however, are formed from brines concentrated by evaporation. The world's most important commercial deposits are of Devonian and Permian age, however soluble potassium bearing salts are presently being concentrated by evaporation in several drainage basins, notably Searles Lake, California, Great Salt Lake, Utah' and in the Dead Sea. At least twenty-four countries are known to have reserves of potash: Canada and the USSR have over 80% of the presently known world reserves, (Figure 1)

Jan 1, 1972

By Cliff Holloway

The past year has been difficult for Canada's primary industries. The mining, oil and forestry industries have been hit by low prices and a reduced demand for natural resources. Foreign competition, militant environmentalists, the breakdown of the Asian and European economies and Canada's shrinking dollar have all put additional pressures on the commodity purchaser to buy smarter. It is easy to appreciate why operations and maintenance supervisors want the best performing product. It makes good sense. The challenge is to source that quality product while staying within the budget. The bottom line (price), however, often becomes the control- ling factor, usually at the expense of quality and performance. This is short-term thinking, often with expensive consequences.

Jan 1, 1999

By James L. Kelley

The Twin Buttes Mine, one of the more recently developed large copper mines in the United States, is in the Pima Mining District about 25 miles south of Tucson (Figure 1). Other copper producing mines in the district are the Esperanza-Sierrita mining operations, five miles to the southwest and the Pima and Mission Mines, seven miles to the north. Copper metal production from the Pima District in 1974 totaled 276,728 tons and the Twin Buttes Mine's share was 46,473 tons or about 17%.' The district's copper production was 31% of Arizona State's production and nearly 17% of the production from the United states in 1974. The Pima District thus ranks as one of the major copper producing areas in this country.

Jan 1, 1976

Computer programs commonly used to simulate mining operations generally require a fair amount of data. The common data input methods have been by either creating an ASCII data file or answering numerous questions during the data input phase. Both methods of data entry are tedious, time consuming, and inflexible. A screen handling system has been developed to drive FORTRAN-77 application software for the MS-DOS environment. The system utilizes keyboard functions with an aid of extended ANSI codes. It also allows a multi-view input data entries.

Jan 1, 1990

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This article offers an examination of a retreat mining method conducted at the Pinoura Mine in India from 2010 to 2017. The method is atypical for coal mines of India’s coalfields. The method executes depillaring in a single pass and does not require the formation of galleries and support installation in splits, thus, reducing the cycle time. A variety of observations are discussed throughout this work and emphasis is placed on field measurements and depillaring under weak roof (RMR = 40–45). This paper discusses design techniques, specifically the estimation of the snook (remnant pillar) size, and important practical observations after the fact. The execution of this method was eventually conducted in eleven panels.

Aug 4, 2020

By Sandip K. Mukherjee

This paper describes the application of pressure foam to control respirable dust in a double-drum longwall mining section. The feasibility of passing an adequate quantity of pressure foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The de- tails of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1984

By J. A. Herbst

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build these mills owing to what is perceived as an excessively large design risk. This risk results from the fact that traditional predictions for mill-scale-up to large diameters are not always accurate. It is apparent that alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses, i.e., grinding kinetics, material transport, and classification, are capable of predicting the performance of small- and intermediate diameter mills (up to 4.3 m (14 ft)) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline" large ball mill (4.7x5.5 m) at Asarco's Sacaton operation, a ball mill (5.0x5.8 m) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5x6.1 m), at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm diameter batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equation is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1983

By Mike Lewis

"Descending several stories down a metal staircase into a shaft spanning a quarter city block -- soon to become Roosevelt Light Rail Station in Seattle, WA -- visitors are greeted with four perfectly round, precast concrete-lined horizontal holes leading deep into the earth. The sound of water trickling out from a small drainage trough can be heard over the faint echoes of construction within. Upon entering, the light is dim, but the air is clear with barely a dust particle flowing through the sunbeams. This type of air quality is only accomplished with diligent controls, and JCM Northlink, the company in charge of building the Northgate Link Extension Project, is taking those measures seriously.Commissioned by Sound Transit, JCM is a joint venture of three companies: Jay Dee Contractors, Frank Coluccio Construction Co. and Michels Corp. The tunnels JCM constructed are intended to provide fast, reliable underground rail service, as well as relieve one of the region’s most congested traffic areas. The $440 million project will connect the Northgate, Roosevelt and University District neighborhoods north of Seattle to the downtown corridor and SeaTac airport further south.The scope of this project includes excavation for two light rail stations, boring of two parallel 5 km- (3.3-mile) long light rail tunnels in six runs and the construction of 23 cross passages. Begun in 2014, Sound Transit estimates that crews excavated more than 382,000 m3 (500,000 cu yds) of soil and installed 7,352 precast concrete tunnel liner rings during the shaft construction and boring phase. Now that tunnel boring is complete, JCM is in the process of constructing the cross passages, which act as maintenance areas and escape routes for passengers. Throughout the entire process, the company has utilized atomized mist to control particle emissions.“Our dust control needs change at every phase of the project and don’t go away until the project is fully complete,” said a JCM safety representative. “We found that different dust suppression technologies were needed at different intervals, but atomized mist seemed to fulfill our needs at every step.”"

Jan 9, 2017

By Barrie C. Butt

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been in progress for six years and the writer has been intimately associated with the project during the five years of exploration and the six years of exploitation. The industry is possibly aware of the fact that the Woodsreef Mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and of the fibre. Because of these unique features, a large volume of research has been undertaken by Woodsreef and by other scientific organisations in Australia, England and Canada on the Woodsreef fibre. The answers to some of the problems have negated some semi-sacred concepts of asbestos ore milling and led to the development of new techniques, such as the adoption of microscopic fibre counts as a routine procedure; the modification of accepted evaluation procedures; the development of new machines for dedusting fibres, and to the recognition of a fibre with a unique milling behaviour pattern and, possibly, properties. The problems experienced can be divided broadly into those associated with the geology and those associated with the physical properties of the fibre. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognised during the exploration stages a feasibility evaluation may be just that little closer to the actual.

Jan 1, 1978

By D. Pappas

Over the past decade, the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry's injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked and injury rate. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992-2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent. Mining Engineering, 2011, Vol. 63, No. 11, pp. 73-79. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Kenneth P. Katen

Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped [ ] that the information presented in this chapter will enable the reader to better understand the two mechanical systems and the mining concepts involved in their employment.

Jan 1, 1981

"Mining of ore bodies that are located at great depths enforces long distances to move the excavated rock masses to the surface. The excavated rock mass contains not only ore that can be economically extracted from the face but also waste, which is usually discarded several steps further downstream in the process. As a result, a large amount of rock is transported to the surface, influencing the costs at which the ore is produced. Reducing the amount of waste rock being transported to the surface by introducing a near-to-face sorting plant would improve the in many cases strained transport system in the deep mine. In this study, one of Boliden’s cut-and-fill mines was analysed with respect to the challenges related to rock transportation and increasing mining depth. The study aims to evaluate the potential use of a new near-to-face sorting system in the operating underground mine. Discrete event simulation was used to study and analyse the rock transportation system with and without the near-to-face sorting plant. The paper shows how the underground rock transportation system and the production were influenced when the near-to-face sorting equipment was added into the current system. INTRODUCTION The locations of waste rejection in the mining processes and the cost of removing waste from the system compared with the cost and energy necessary for further comminution are important parts in the material handling system (Bowman and Bearman, 2014). In an underground mine, longer material transportation distances generate the need for further investment in the mobile fleet and ancillary equipment in order to reduce the waste from the material handling as early as possible. One of the ways of reducing the waste (coarse particle size) in material handling is by use of pre-concentration. The benefits of pre-concentration are well known (Schena et al. 1990; Feasby, 1995; Peters et al. 1999; Klein et al. 2002), as well as the factors governing the feasibility of underground pre-concentration (Peters et al., 1999) and the mining integration issues (Klein et al. 2003). In the Onaping Depth orebody in Sudbury, Ontario the study of implementing the pre-concentration resulted in increased capital costs of 6% and a reduction in the operating costs of between 20-40% (Bamber et al, 2004). In this paper, the effects on the production and the transportation system of implementing underground pre-concentration by means of a near-to-face ore sorting plant in the Kristineberg mine are modeled and analyzed using the AutoMod tool. This tool is based on discrete event simulation (DES) (Banks, 2004), allowing high flexibility in customization and enabling the user to view the production of the system before ore sorting plant integration. The sorting plant selected in the simulation is built from modules. The material is fed by conveyor and goes through the comminution, classification, sorting and service processes after which the waste is redirected to backfill headings via trucks. The system mechanically ejects the particles from the feed stream on the basis of the information obtained from both the XRT sensor’s signal and 3D laser scanner based on both density and rate of refraction of light within a particular mineral. The sorting plant could pre-concentrate the metal ore up to 300 mm size. The plant requires little auxiliary infrastructure, is easily modularized for underground installation and can be easily relocated to different areas."

Jan 1, 2016

By Xiaolong Bi, Shaohua Luo, Longjiao Chang, Shiyuan Cao, Jianan Liu

iliary agent was proposed. The mineralogical transformation and silicon extraction kinetics of laterite nickel ore in alkaline hydrothermal treatment were studied. The effects of reaction temperature (175 ~ 250℃), molar ratios of sodium hydroxide to ore (1.05 ~ 1.2:1), and laterite nickel ore particle size (44 ~ 178 μm) on the extraction ratio of silica were investigated by using the shrinking core model. The results show that the extraction ratio of silica increases with the increase of reaction temperature, sodium hydroxide to ore molar ratio, reaction time, and the decrease of raw ore particle size. The kinetic analysis shows that the separation of silica in laterite ore can be described by internal diffusion model. The apparent activation energy (Ea) of the reaction was 8.87 kJ mol− 1, and the kinetic modeling was established.

Dec 2, 2021

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

By J. S. Peterson

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Jan 1, 1997